Get Other Controls and Equipment -> Audio system (Type A / Type B / Type C) (if equipped) Guide for Suzuki Ignis SUV Second Generation (2016-2024)

5-33

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

Audio system (Type A / Type B / Type C) (if equipped)

75RM080

Type A: AM/FM/DAB CD player with Bluetooth

function

Type B: AM/FM CD player with Bluetooth

function

Type C: AM/FM CD player without Bluetooth

function

EXAMPLE

Type A Type CType B

5-34

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

Safety information Notes on discs

Precautions

• When the inside of the vehicle is very

cold and the player is used soon after

switching on the heater, condensation

may form on the disc or the optical

parts of the player and proper playback

may not be possible. If condensation

forms on the disc, wipe it off with a soft

cloth. If condensation forms on the opti-

cal parts of the player, do not use the

player for about one hour. This will

allow the condensation to disappear

normally.

• Driving on extremely bumpy roads

which cause severe vibrations may

cause sound to skip.

• This unit uses a precision mechanism.

Even in the event that trouble arises,

never open the case, disassemble the

unit, or lubricate the rotating parts.

Bring the unit to an authorized SUZUKI

dealer.

Cautions on handling

52D274

This unit has been designed specifically for

playback of compact discs bearing mark

(A) shown above.

No other discs can be played.

WARNING

If you pay too much attention to

operating the audio system or view-

ing the audio system display while

driving, an accident can occur. If

you set the sound volume too loud,

it could prevent you from being

aware of road and traffic conditions.

• Keep your eyes on the road and

your mind on the drive. Avoid pay-

ing too much attention to operat-

ing the audio system or viewing

the audio system display.

• Familiarize yourself with the audio

system controls and operation of

the audio system before driving.

• Preset your favorite radio stations

before driving so that you can

quickly tune to them using the

presets.

• Set the sound volume to a level

that will allow you to continue to

be aware of road and traffic condi-

tions while driving.

(A)

5-35

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

52D275

To remove the compact disc from its stor-

age case, press down on the center of the

case and lift the disc out, holding it care-

fully by the edges.

Always handle the compact disc by the

edges.

Never touch the surface.

52D347

To remove fingermarks and dust, use a

soft cloth, and wipe in a straight line from

the center of the compact disc to the cir-

cumference.

52D277

New discs may have some roughness

around the edges. The unit may not work

or the sound may skip if such discs are

used. Use a ball-point pen (B), etc. to

remove the roughness (C) from edges of

the disc before inserting it into the unit.

52D348

Never stick labels on the surface of the

compact disc or write on the surface with a

pencil or pen.

52D349

Do not use any solvents such as commer-

cially available cleaners, anti-static spray,

or thinner to clean compact discs.

Removing the disc

Proper way to hold

the compact disc

(B)

(C)

5-36

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

52D350

Do not use compact discs that have large

scratches, are misshaped, or cracked, etc.

Use of such discs will cause damage or

prevent the system from operating prop-

erly.

52D351

Do not expose compact discs to direct sun-

light or any heat source.

NOTE:

• Do not use commercially available CD

protection sheets or discs equipped with

stabilizers, etc.

These may get caught in the internal

mechanism and damage the disc.

• It may be impossible to play CD-R discs

with this unit due to the recording condi-

tions.

• CD-RW discs cannot be played with this

unit.

5-37

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

The Bluetooth

word mark and logo are

registered trademarks and are owned by

the Bluetooth SIG, Ink.

Stop using this unit and a Bluetooth

ready device whenever requested.

This unit shares the communication fre-

quency with other private or public wireless

communication equipment such as a wire-

less LAN and other wireless communica-

tion radios.

You should stop using this unit whenever

you are notified that your unit disturbs

other wireless communication immediately.

Access to http:www.ptc.panaso

enter the below

Model No. into the keyword search box,

you can download the latest “DECLARA-

TION of CONFORMITY” (DoC).

Set No. AZ1601

WARNING

This is a class I laser product. Use

of controls or adjustments or perfor-

mance of procedures other than

those specified herein may result in

hazardous radiation exposure.

Do not open covers and do not

attempt to repair this unit by your-

self.

Ask an authorized dealer for the

repair.

5-38

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

Information on disposal for users of waste electrical & electronic equip-

ment (private households)

This symbol on the products and/or accompanying documents

means that used electrical and electronic products should not be

mixed with general household waste.

For proper treatment, recovery and recycling, please take these

products to designated collection points, where they will be accepted

on a free of charge basis. Alternatively, in some countries you may

be able to return your products to your local retailer upon the pur-

chase of an equivalent new product.

Disposing of this product correctly will help to save valuable

resources and prevent any potential negative effects on human

health and the environment which could otherwise arise from inap-

propriate waste handling. Please contact your local authority for fur-

ther details of your nearest designated collection point.

Penalties may be applicable for incorrect disposal of this waste, in

accordance with national legislation.

For business users in the European Union

If you wish to discard electrical and electronic equipment, please contact your dealer or

supplier for further information.

Information on disposal in other countries outside the European Union

This symbol is only valid in the European Union.

If you wish to discard this product, please contact your local authorities or dealer and ask

for the correct method of disposal.

68LM560

5-39

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

Part 15 of the FCC Rules

FCC ID: ACJ932AZ1601

NOTE:

Properly shielded and grounded cables

and connectors must be used for connec-

tion to host computers and/or peripherals

in order to meet FCC emission limits.

The Bluetooth

word mark and logo are

registered trademarks and are owned by

the Bluetooth SIG, Ink.

NOTE:

This equipment complies with FCC radia-

tion exposure limits set forth for uncon-

trolled equipment and meets the FCC

radio frequency (RF) Exposure Guidelines

in Supplement C to OET65. This equip-

ment has very low level of RF energy

which does not comply with maximum per-

missive exposure (MPE) evaluation. But it

is desirable that it should be installed and

operated with at least 20cm and more

between the radiator and person’s body

(excluding extremities: hands, wrists, feet

and ankles).

WARNING

RF Exposure

This equipment complies with FCC

radiation exposure limits set forth for

an uncontrolled environment and

meets the FCC radio frequency (RF)

Exposure Guidelines. This equipment

has very low levels of RF energy that

it deemed to comply without maxi-

mum permissive exposure evaluation

(MPE). [But it is desirable that it

should be installed and operated

keeping the radiator at least 20 cm or

more away from person’s body.]

CAUTION

Changes or modifications not

expressly approved by the party

responsible for compliance could

void the user’s authority to operate

the equipment.

WARNING

This is a class I laser product. Use of

controls or adjustments or perfor-

mance of procedures other than

those specified herein may result in

hazardous radiation exposure.

Do not open covers and do not

attempt to repair this unit by yourself.

Ask an authorized dealer for the

repair.

5-40

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

Stop using this unit and a Bluetooth

ready device whenever requested.

This unit shares the communication fre-

quency with other private or public wireless

communication equipment such as a wire-

less LAN and other wireless communica-

tion radios.

You should stop using this unit whenever

you are notified that your unit disturbs

other wireless communication immediately.

NOTE:

These limits are designed to provide rea-

sonable protection against harmful interfer-

ence in a residential installation. This

equipment generates, uses and can radi-

ate radio frequency energy and, if not

installed and used in accordance with the

instructions, may cause harmful interfer-

ence to radio communications. However,

there is no guarantee that interference will

not occur in a particular installation. If this

equipment does cause harmful interfer-

ence to radio or television reception, which

can be determined by turning the equip-

ment off and on, the user is encouraged to

try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving anten-

na.

• Increase the separation between the

equipment and receiver.

• Connect the equipment into an outlet on

a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced

radio/TV technician for help.

• This transmitter must not be co-located

or operated in conjunction with any other

antenna or transmitter.

5-41

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

Basic operations

75RM081

(1) “VOL PUSH PWR” knob

(2) “TUNE/FLD PUSH SOUND” knob

(3) MUTE button

(2)(1)

(2)

(3)

(1)

Type A

Type B

EXAMPLE

Type C

Turning on/off power

Press “VOL PUSH PWR” knob (1) to turn

on the power. The unit starts to operate in

the previous setting that the power was

turned off.

Adjusting the volume

Turn “VOL PUSH PWR” knob (1).

Turning it clockwise increases the volume;

turning it counterclockwise decreases the

volume.

NOTE:

For the purposes of safe driving, adjust the

audio volume to a level that allows you to

hear sounds outside of the vehicle includ-

ing car horns and particularly emergency

vehicle sirens.

Mute

Press MUTE button (3) to mute the sound.

To cancel the mute, press MUTE button (3)

again.

5-42

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

Adjusting bass/treble/balance/fader

1) Press “TUNE/FLD PUSH SOUND”

knob (2).

Each time the knob is pressed, sound

adjustment will change as follows:

2) Turn “TUNE/FLD PUSH SOUND” knob

(2) to adjust the sound.

Adjusting the AVC (Auto volume con-

trol)

The Auto Volume Control (AVC) function

automatically adjusts (increases/

decreases) the sound volume in accor-

dance with vehicle speed. The AVC control

is provided with three selectable levels

(LEVEL OFF, 1, 2, 3). The range of volume

adjustment increases together with the

LEVEL number.

1) Press “TUNE/FLD PUSH SOUND”

knob (2) until the AVC adjustment mode

is selected.

2) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select the desired AVC adjust-

ment level. (Initial setting: LEVEL 2)

Preset-EQ

Preset-EQ calls up various sound types in

accordance with the listening music type.

1) Press “TUNE/FLD PUSH SOUND”

knob (2) several times until “PRESET-

EQ” appears.

2) Turn “TUNE/FLD PUSH SOUND” knob

(2).

Each time the knob is turned, preset

EQ mode will change as follows:

Preset-EQ (EQ OFF)

Bass adjustment (BASS 0)

Treble adjustment (TREBLE 0)

Balance adjustment (BALANCE 0)

Fader adjustment (FADER 0)

AVC adjustment (AVC LEVEL 2)

OFF (FLAT)

JAZZ

ROCK

POP

CLASSIC

HIP-HOP

5-43

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

Listening to the radio (Type A)

75RM082

(2)

(3)

(6)

(4)

(5)

(1)

EXAMPLE

Display

68LM561

(1) “RADIO” button

(2) UP button

(3) DOWN button

(4) “TUNE/FLD PUSH SOUND” knob

(5) PRESET buttons ([1] to [6])

(6) “AS” button

(A) Band

(B) Frequency

(A)

(B)

5-44

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

Selecting the reception band

Press the “RADIO” button (1).

Each time the button is pressed, the recep-

tion band will change as follows:

Seek tuning

Press UP button (2) or DOWN button (3).

The unit stops searching for a station at a

frequency where a broadcast station is

available.

NOTE:

If AF is on, the unit searches for RDS sta-

tions only.

Manual tuning

Turn “TUNE/FLD PUSH SOUND” knob (4).

The frequency being received is displayed.

Preset memory

1) Select the desired station.

2) Hold down a desired button ([1] to [6])

of PRESET buttons (5) to which you

want to store the station for 2 seconds

or longer.

Auto store

Hold down “AS” button (6) for 2 seconds or

longer.

6 stations in good reception will automati-

cally be stored to PRESET buttons (5) in

order, starting from a station whose fre-

quency is the lowest.

NOTE:

• Auto store can be released by pressing

“AS” button (6) while auto store is under

way.

• When the auto store is performed, the

station previously stored in the memory

at the position is overwritten.

• When there are fewer than 6 stations that

can be stored even if 1 round of auto

store operation is performed, no station

will be stored at the remaining PRESET

buttons (5).

• 6 stations can be preset for FM1 and

FM2 in common, and 6 stations for AM in

auto store mode.

• If AF is on, the unit searches for RDS

stations only.

Auto store mode on/off

Press “AS” button (6).

Each time the button is pressed, the mode

is switched as follows:

Radio reception

Radio reception can be affected by envi-

ronment, atmospheric conditions, or radio

signal’s power and distance from the sta-

tion. Nearby mountains and buildings may

interfere or deflect radio reception, causing

poor reception. Poor reception or radio

static can also be caused by electric cur-

rent from overhead wires or high voltage

power lines.

FM1 FM2 DAB1 (if equipped)

AM DAB2 (if equipped)

AS mode on AS mode off

5-45

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

Listening to the radio (Type B / Type C)

75RM083

(5)

(3)

(4)

(1)

(2)

(6)

(7)

(5)

(3)

(4)

(1)

(2)

(6)

(7)

Type B

Type C

EXAMPLE

Display

(1) “FM” button

(2) “AM” button

(3) UP button

(4) DOWN button

(5) “TUNE/FLD PUSH SOUND” knob

(6) PRESET buttons ([1] to [6])

(7) “AS” button

(A) Band

(B) Frequency

(A)

(B)

5-46

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

Selecting the FM band

Press “FM” button (1).

Each time the button is pressed, the recep-

tion band will change as follows:

Selecting the AM band

Press “AM” button (2).

Seek tuning

Press UP button (3) or DOWN button (4).

The unit stops searching for a station at a

frequency where a broadcast station is

available.

Manual tuning

Turn “TUNE/FLD PUSH SOUND” knob (5).

The frequency being received is displayed.

Preset memory

1) Select the desired station.

2) Hold down a desired button ([1] to [6])

of the PRESET buttons (6) to which you

want to store the station for 2 seconds

or longer.

Auto store

Hold down “AS” button (7) for 2 seconds or

longer.

6 stations in good reception will automati-

cally be stored to PRESET buttons (6) in

order, starting from a station whose fre-

quency is the lowest.

NOTE:

• Auto store can be released by pressing

“AS” button (7) while auto store is under

way.

• When the auto store is performed, the

station previously stored in the memory

at the position is overwritten.

• When there are fewer than 6 stations

that can be stored even if 1 round of

auto store operation is performed, no

station will be stored at the remaining

PRESET buttons (6).

• 6 stations can be preset for FM1 and

FM2 in common, and 6 stations for AM

in auto store mode.

Auto store mode on/off

Press “AS” button (7).

Each time the button is pressed, the mode

is switched as follows:

Radio reception

Radio reception can be affected by envi-

ronment, atmospheric conditions, or radio

signal’s power and distance from the sta-

tion. Nearby mountains and buildings may

interfere or deflect radio reception, causing

poor reception. Poor reception or radio

static can also be caused by electric cur-

rent from overhead wires or high voltage

power lines.

FM1 FM2

AS mode on AS mode off

5-47

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

Using the RDS functions (Type A)

75RM084

(4)

(5)

(6)

(1)

(3) (2)

EXAMPLE

Display

68LM562

(1) “TA” button

(2) “RDM/PTY” button

(3) “RPT/AF” button

(4) UP button

(5) DOWN button

(6) “DISP” button

(A) Band

(B) Channel number

(A)

(C)

(B)

5-48

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

TA (Traffic Announcement) on/off

Press “TA” button (1).

Each time it is pressed, TA adjustment is

changed as follows:

NOTE:

• For listening to only traffic information,

activate TA. Once traffic information

starts, the volume changes automatically.

• “TP” indicator lights up when TP (Traffic

Program) is on. It blinks when no TP data

is received.

• “TA” indicator lights while TA is activated.

On the other hand, “TA” indicator blinks if

the TP data cannot be received.

• If UP button (4) or DOWN button (5) is

pressed while TA or TP is set to on, the

unit searches for a TP station.

• If no TP station is received, the unit dis-

plays “TP NOTHING”.

PTY (Program Type) search

1) Press “RDM/PTY” button (2) to select

PTY mode.

2) Press “RDM/PTY” button (2) while PTY

is displayed.

Each time it is pressed, PTY adjust-

ment is changed as follows:

3) Press UP button (4) or DOWN button

(5) while PTY is displayed.

Search begins.

NOTE:

If no PTY information is received, the unit

displays “NOPTY”.

AF (Alternative Frequency) on/off

Press “RPT/AF” button (3).

Each time it is pressed, AF adjustment is

changed as follows:

AF: If the reception condition becomes

poor, the frequency of the same program

with good reception is automatically

searched.

REG: With regard to the automatically

searched frequency with AF activated, the

alternative frequency of the same program

is searched within the present region when

REG is activated.

NOTE:

“AF” indicator lights up when AF is on. In

addition, “REG” indicator lights up when

REG is on.

OFF TP ON TA ON

NEWS

SPORTS

TALK

POP

CLASSICS

AF-ON/REG-OFF

AF-ON/REG-ON

AF-OFF/REG-OFF

5-49

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

TA standby

At the moment traffic information is

received while the source is set to CD,

USB, iPod

, AUX, DAB, or Blue-

tooth

audio with TA activated, the source

is automatically changed to radio. After

reception of traffic information, the source,

which was selected before being changed

to radio, resumes.

NOTE:

If no TP station can be received while the

unit stands by for TA, it automatically

searches for a TP station.

EON (Enhanced Other Network)

When the EON data is received with TP or

TA activated, “EON” indicator lights up,

and the traffic information from a network

other than the currently received station is

allowed to be received.

Emergency announcement reception

Emergency announcements are automati-

cally received and displayed.

5-50

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

Listening to a CD

75RM085

(5)

(4)

(2)

(3)

(8)(6)(7)

(1)

(5)

(4)

(2)

(3)

(8)(6)(7)

(1)

(5)

(4)

(2)

(3)

(8)(6)(7)

(1)

Type A

Type B

EXAMPLE

Type C

Display

(1) Insertion slot

(2) EJECT button

(3) “CD” button

(4) UP button

(5) DOWN button

(6) “RPT” button

(7) “RDM” button

(8) “DISP” button

(A) Track number

(B) Play time

NOTE:

This product does not support 8 cm CD

(sometimes called as “mini single CD”, “3-

inch CD”, “CD3”, etc.).

(B)

(A)

5-51

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

• CDs or CD-ROMs without mark (A) can-

not be used.

• Some discs recorded in CD-R/CD-RW

format may sometimes be impossible to

use.

• A CD is to be inserted with its label side

up.

• When there is a CD already in the unit, it

is impossible to insert another CD with-

out ejecting the CD in the unit. Do not

use force to insert a CD into the CD

insertion slot.

Loading a CD

Insert a CD in the insertion slot (1).

When the CD is loaded, it starts to play.

Ejecting a CD

Press EJECT button (2).

When the ignition switch is in “LOCK” posi-

tion or the engine switch is in LOCK (OFF)

mode, the CD remained ejected for around

15 seconds or longer will automatically be

drawn inside the unit. (Auto reload func-

tion)

The backup eject function:

This function allows you to eject a CD by

pressing EJECT button (2) even when the

ignition switch is in “LOCK” position or the

engine switch is in LOCK (OFF) mode.

Listening to a CD

When a CD is inserted, playback will auto-

matically start.

When a CD is already inside the unit,

press “CD” button (3) to start playback.

Selecting a track

• Press UP button (4) to listen to the next

track.

• Press DOWN button (5) twice to listen to

the previous track.

When DOWN button (5) is pressed

once, the track currently being played

will start from the beginning again.

Fast forwarding/rewinding a track

• Hold down UP button (4) to fast forward

the track.

• Hold down DOWN button (5) to fast

rewind the track.

(A)

NOTICE

• Never insert your finger or hand

into the CD insertion slot. Never

insert foreign objects.

• Never insert a CD with glue coming

out from adhesive tape or a rental

CD label or with a trace indicating

that adhesive tape or a rental CD

label has been removed. This may

cause the CD not to eject or result

in a malfunction.

NOTICE

If you forcefully try to push an

ejected CD inside the unit before auto

reloading, the disc surface might be

scratched.

Before reloading a CD, remove it

from the unit completely.

5-52

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

Random playback

Press “RDM” button (7).

Each time the button is pressed, the mode

will change as follows:

• TRACK RANDOM

The random indicator “RDM” will light.

The tracks in the loaded disc will be

played in random order.

Repeat playback

Press “RPT” button (6).

Each time the button is pressed, the mode

will change as follows:

• TRACK REPEAT

The repeat indicator “RPT” will light.

The track currently being played will be

played repeatedly.

Display change

Press “DISP” button (8).

Each time the button is pressed, display

will change as follows:

NOTE:

• “NO TITLE” will be displayed when there

is no text information in the disc currently

being played.

• If text data contains more than 16 char-

acters, “>” mark will appear at the right

end. Holding down “DISP” button (8) for

1 second or longer can display the next

page.

OFF TRACK RANDOM

OFF TRACK REPEAT

Play time

Disc title

Track title

5-53

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

Listening to an MP3/WMA/AAC disc

75RM086

(3)

(2)

(1)

(6)

(4)(5)

(3)

(2)

(1)

(6)

(4)(5)

(3)

(2)

(1)

(6)

(4)(5)

Type A

Type B

EXAMPLE

Type C

Display

(1) “TUNE/FLD PUSH SOUND” knob

(2) UP button

(3) DOWN button

(4) “RPT” button

(5) “RDM” button

(6) “DISP” button

(A) Folder number

(B) Track number

(D) File type

(C)

(B)(A)

(D)

5-54

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

Selecting a folder

Turn “TUNE/FLD PUSH SOUND” knob (1)

to select a folder.

Selecting a track

• Press UP button (2) to listen to the next

track.

• Press DOWN button (3) twice to listen to

the previous track.

When DOWN button (3) is pressed

once, the track currently being played

will start from the beginning again.

Fast forwarding/rewinding a track

• Hold down UP button (2) to fast forward

the track.

• Hold down DOWN button (3) to fast

rewind the track.

Random playback

Press “RDM” button (5).

Each time the button is pressed, the mode

will change as follows:

• FOLDER RANDOM

The random indicator “F.RDM” will light.

The tracks in the current folder will be

played in random order.

•ALL RANDOM

The random indicator “RDM” will light.

The tracks in the loaded disc will be

played in random order.

Repeat playback

Press “RPT” button (4).

Each time the button is pressed, the mode

will change as follows:

• FILE REPEAT

The repeat indicator “RPT” will light.

The track currently being played will be

played repeatedly.

• FOLDER REPEAT

The repeat indicator “F.RPT” will light.

All tracks in the currently selected folder

will be played repeatedly.

OFF FOLDER RANDOM ALL RANDOM

OFF FILE REPEAT FOLDER REPEAT

5-55

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

Display change

Press “DISP” button (6).

Each time the button is pressed, display

will change as follows:

NOTE:

• “NO TITLE” will be displayed when there

is no text information in the disc currently

being played.

• If text data contains more than 16 char-

acters, “>” mark will appear at the right

end. Holding down “DISP” button (6) for

1 second or longer can display the next

page.

Notes on MP3/WMA/AAC

What is MP3?

• An abbreviation of “MPEG audio layer3”,

MP3 is an audio compression format

that has become the standard format

among PC users. Its merit is that the

original audio data is compressed to

approximately 1/10 and high sound qual-

ity is maintained. This means that it is

possible to store the data of approxi-

mately 10 music CDs on a single CD-R/

RW disc, which in turn makes it possible

to play music for a long time without hav-

ing to change the disc.

What is WMA?

• An abbreviation of “Windows Media

Audio,” WMA is an audio compression

format developed by Microsoft.

• WMA files for which the DRM (Digital

Rights Management) function is on can-

not be played.

• Windows Media

and the Windows

logo are trademarks or registered trade-

marks of Microsoft Corporation in the

United States and other countries.

What is AAC?

• An abbreviation of “Advanced Audio

Coding,” AAC is an audio compression

format used by MPEG2 and MPEG4.

Points to remember when making MP3/

WMA/AAC files

Common

• High bit rate and high sampling fre-

quency are recommended for high qual-

ity sounds.

• Selecting VBR (Variable Bit Rate) is not

recommended. Selecting VBR may

cause display of incorrect playing time

and jumpiness of playback.

• Playback sound quality varies depend-

ing on the encoding environment. For

details, refer to the user manual of the

encoding software and the writing soft-

ware in use.

Play time

Folder name

File name

Album name (MP3, AAC only)

Track title

Artist name

NOTICE

Never use “.mp3”, “.wma” or “.m4a”

as a file name extension if it is not in

the MP3/WMA/AAC format file. Fail-

ure to observe this may result in

damage to the speaker due to noise

production.

5-56

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

Recording MP3/WMA/AAC files on a CD

media

• It is recommended not to write both CD-

DA files and MP3/WMA/AAC files on a

disc.

• If both CD-DA files and MP3/WMA/AAC

files are on the same disc, tracks may

not be played in the correct order or

some tracks may not be played at all.

• When storing both MP3 data and WMA

data on the same disc, sort and place

them in different folders.

• Do not write files other than MP3/WMA/

AAC files and unnecessary folders on a

disc.

• MP3/WMA/AAC files should be named

to meet the standards and the file sys-

tem specifications as shown below.

• The file extension “.mp3”, “.wma” or

“.m4a” should be assigned to files based

on their format independently.

• You may encounter a trouble in playing

MP3/WMA/AAC files or displaying infor-

mation of MP3/WMA/AAC files depend-

ing on the writing software or CD

recorder in use.

• This unit does not have a playlist func-

tion.

• It is recommended to write discs in Disc-

at-Once mode even though Multi-ses-

sion mode is supported. These modes

are the methods for writing audio data in

CD.

Compression formats

MP3

• Bit rate

MPEG1 Audio Layer III: 32 k - 320 kbps

MPEG2 Audio Layer III: 8 k - 160 kbps

MPEG2.5 Audio Layer III: 8 k - 160 kbps

• Sampling frequency

MPEG1 Audio Layer III: 32 k/44.1 k/

48 kHz

MPEG2 Audio Layer III: 16 k/22.05 k/

24 kHz

MPEG2.5 Audio Layer III: 8 k/11.025 k/

12 kHz

WMA (Ver. 7, Ver. 8, Ver. 9*)

• Bit rate: CBR 32 k - 320 kbps

• Sampling frequency: 32 k/44.1 k/48 kHz

* WMA 9 Professional/LossLess/Voice are

not supported.

AAC*

• Bit rate: ABR 16 k - 320 kbps

• Sampling frequency: 32 k/44.1 k/48 kHz

* Apple Lossless is not supported.

Supported file systems

ISO 9660 Level 1/Level 2, Joliet, Romeo

Maximum number of files/folders

• Maximum number of files: 512

• Maximum number of files in a folder: 255

• Maximum depth of tree structure: 8

• Maximum number of folders: 255

(Root folder is included.)

5-57

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

Listening to files stored in a USB device

75RM087

(4)

(3)

(2)

(7)

(5)(6)

(1)

(4)

(3)

(2)

(7)

(5)(6)

(1)

(4)

(3)

(2)

(7)

(5)(6)

(1)

Type A

Type B

EXAMPLE

Type C

Display

(1) “MEDIA” button

(2) “TUNE/FLD PUSH SOUND” knob

(3) UP button

(4) DOWN button

(5) “RPT” button

(6) “RDM” button

(7) “DISP” button

(A) Folder number

(B) Track number

(D) File type

NOTICE

Do not connect any USB device other

than a USB memory or a USB audio

player. Do not connect multiple USB

devices to the USB connector using a

USB hub, etc. Supplying power to

multiple USB devices from the con-

nector could cause overheating and

smoking.

(C)

(B)(A)

(D)

5-58

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

Selecting a USB device mode

Press “MEDIA” button (1).

Each time the button is pressed, the mode

will change as follows:

Selecting a folder

Turn “TUNE/FLD PUSH SOUND” knob (2)

to select the desired folder.

Selecting a track

• Press UP button (3) to listen to the next

track.

• Press DOWN button (4) twice to listen to

the previous track.

When DOWN button (4) is pressed

once, the track currently being played

will start from the beginning again.

Fast forwarding/rewinding a track

• Hold down UP button (3) to fast forward

the track.

• Hold down DOWN button (4) to fast

rewind the track.

Random playback

Press “RDM” button (6).

Each time the button is pressed, the mode

will change as follows:

• FOLDER RANDOM

The random indicator “F.RDM” will light.

The tracks in the currently selected

folder will be played in random order.

•ALL RANDOM

The random indicator “RDM” will light.

The tracks in the connected USB device

will be played in random order.

Repeat playback

Press “RPT” button (5).

Each time the button is pressed, the mode

will change as follows:

• FILE REPEAT

The repeat indicator “RPT” will light.

The track currently being played will be

played repeatedly.

• FOLDER REPEAT

The repeat indicator “F.RPT” will light.

All the tracks in the folder currently

selected will be played repeatedly.

Display change

Press “DISP” button (7).

Each time the button is pressed, display

will change as follows:

NOTE:

• “NO TITLE” will be displayed when there

is no text information in the file currently

being played.

• If text data contains more than 16 char-

acters, “>” mark will appear at the right

end. Holding down “DISP” button (7) for

1 second or longer can display the next

page.

USB (iPod

) (if equipped)

Bluetooth

audio (if equipped)

AUX (if equipped)

OFF FOLDER RANDOM ALL RANDOM

OFF FILE REPEAT FOLDER REPEAT

Play time

Folder name

File name

Album name (MP3, AAC only)

Track title

Artist name

5-59

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

Notes on USB device

Compatible USB devices

• USB mass storage class

For details as to whether your USB

memory/USB audio is compatible with

USB mass storage class, please contact

the USB memory/USB audio manufac-

turer.

• USB standard compatibility 1.1/2.0 full

speed

• File system FAT12/16/32, VFAT

• Maximum current less than 1.0 A

• If devices such as USB hub, extension

cable are connected to the audio sys-

tem, it may not be recognized. In such

case, connect the USB device directly to

the audio system.

• Devices such as MP3 player/mobile

phone/digital camera may not be recog-

nized by the audio system for playing

music.

USB device connection

• When connecting a USB device, check

that the connector is pushed all the way

into the port.

• Do not leave the USB device for long

periods of time inside the vehicle where

the temperature can rise too high.

• Back up any important data beforehand.

We cannot accept responsibility for any

lost data.

• It is recommended not to connect a USB

device that contains data files other than

MP3/WMA/AAC format.

Recording MP3/WMA/AAC files on a

USB device

• Playback or display may not be possible

depending on the type of USB device in

use or the condition of the recording.

• Depending on the connected USB mem-

ory, the files may be played in different

order from the stored one.

Compression formats

MP3

• Bit rate

MPEG1 Audio Layer III: 32 k - 320 kbps

MPEG2 Audio Layer III: 8 k - 160 kbps

MPEG2.5 Audio Layer III: 8 k - 160 kbps

• Sampling frequency

MPEG1 Audio Layer III: 32 k/44.1 k/48 kHz

MPEG2 Audio Layer III: 16 k/22.05 k/24 kHz

MPEG2.5 Audio Layer III: 8 k/11.025 k/12 kHz

WMA (Ver. 7, Ver. 8, Ver. 9*)

• Bit rate: CBR 32 k - 320 kbps

• Sampling frequency: 32 k/44.1 k/48 kHz

* WMA 9 Professional/LossLess/Voice are

not supported.

AAC*

• Bit rate: ABR 16 k - 320 kbps

• Sampling frequency: 32 k/44.1 k/48 kHz

* Apple Lossless is not supported.

Maximum number of files/folders

• Maximum number of files: 2500

• Maximum number of files in a folder: 255

• Maximum depth of tree structure: 8

• Maximum number of folders: 255

(Root folder is included.)

5-60

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

Listening to an iPod

75RM088

(4)

(3)

(2)

(8)

(1)

(7)(5)(6)

(4)

(3)

(2)

(8)

(1)

(7)(5)(6)

(4)

(3)

(2)

(8)

(1)

(7)(5)(6)

Type A

Type B

EXAMPLE

Type C

Display

(1) “MEDIA” button

(2) “TUNE/FLD PUSH SOUND” knob

(3) UP button

(4) DOWN button

(5) “RPT” button

(6) “RDM” button

(7) “DISP” button

(8) PRESET buttons ([1] to [6])

(A) Track title

(B) Track number

(C)

(A)

(B)

5-61

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

Selecting an iPod

mode

Press “MEDIA” button (1).

Each time the button is pressed, the mode

will change as follows:

Selecting a track

• Press UP button (3) to listen to the next

track.

• Press DOWN button (4) twice to listen to

the previous track.

When DOWN button (4) is pressed

once, the track currently being played

will start from the beginning again.

Fast forwarding/rewinding a track

• Hold down UP button (3) to fast forward

the track.

• Hold down DOWN button (4) to fast

rewind the track.

Random playback

Press “RDM” button (6).

Each time the button is pressed, the mode

will change as follows:

• SONG RANDOM

The random indicator “RDM” will light.

The tracks in the iPod

will be played in

random order.

• ALBUM RANDOM

The random indicator “F.RDM” will light.

The albums in the iPod

will be played in

random order.

Repeat playback

Press “RPT” button (5).

Each time the button is pressed, the mode

will change as follows:

• SONG REPEAT

The repeat indicator “RPT” will light.

The track currently being played will be

played repeatedly.

Display change

Press “DISP” button (7).

Each time the button is pressed, display

will change as follows:

NOTE:

If text data contains more than 16 charac-

ters, “>” mark will appear at the right end.

Holding down “DISP” button (7) for 1 sec-

ond or longer can display the next page.

USB (iPod

) (if equipped)

Bluetooth

audio (if equipped)

AUX (if equipped)

OFF SONG RANDOM ALBUM RANDOM

OFF SONG REPEAT

Playlist name /

Track title (Playlist mode only)

Artist name /

Track title

Album name /

Track title

Track title /

Play time

5-62

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

Playing mode selection

1) Press the button numbered [6] of PRE-

SET buttons (8) for 1 second or longer.

2) Turn “TUNE/FLD PUSH SOUND” knob

(2).

Each time the knob is turned, the mode

will change as follows:

3) Press “TUNE/FLD PUSH SOUND”

knob (2) to select the desired mode.

NOTE:

• When the button numbered [6] of PRE-

SET buttons (8) is pressed, the previous

mode will be displayed.

Notes on iPod

Supported iPod

•iPod

touch (6th generation)

•iPod

touch (5th generation)

•iPod

touch (4th generation)

•iPod

touch (3rd generation)

•iPod

touch (2nd generation)

•iPod

touch (1st generation)

•iPod

classic

•iPod

nano (7th generation)

•iPod

nano (6th generation)

•iPod

nano (5th generation)

•iPod

nano (4th generation)

•iPod

nano (3rd generation)

•iPod

nano (2nd generation)

•iPod

nano (1st generation)

•iPod

(5th generation)

• iPhone

6S Plus

• iPhone

6 Plus

• iPhone

3GS

• iPhone

* Some functions may not be available

depending on the model of iPod

*iPod

is a trademark of Apple Inc., regis-

tered in the U.S. and other countries.

* iPhone

is a trademark of Apple Inc.,

registered in the U.S. and other coun-

tries.

* Apple is not responsible for the opera-

tion of this device or its compliance with

safety and regulatory standards.

iPod

connection

• Make sure to detach the iPod

after

turning the ignition switch to “LOCK”

position or pressing the engine switch to

change the ignition mode to LOCK

(OFF). The iPod

may not be shut down

when it is being connected and may

result in battery depletion.

• Do not connect iPod

accessories such

as an iPod

remote control or head-

phones while connecting the iPod

with

the unit. The unit may not operate cor-

rectly.

PLAYLIST

ARTIST

ALBUM

SONGS

PODCAST

GENRE

AUDIOBOOK

5-63

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

AUX function

75RM089

(1) “MEDIA” button

(1)

(1) (1)

Type A

Type B

EXAMPLE

Type C

AUX connection

To listen to auxiliary audio sources (sold

separately) through the unit, follow the

instruction below.

1) Connect the auxiliary audio source to

the AUX/USB socket (separately

attached) with an AUX cable.

2) Press “MEDIA” button (1).

Each time the button is pressed, the

mode will change as follows:

CAUTION

• Before connection, mute the unit,

and also keep the volume of the

auxiliary audio source within a

range that will not cause distortion.

• When the audio source is turned

off, noise may be emitted. Be sure

to turn off the unit or switch to

another mode before turning off the

audio source.

USB (iPod

) (if equipped)

Bluetooth

audio (if equipped)

AUX (if equipped)

5-64

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

NOTE:

• Please consult your place of purchase

for details about whether a given auxil-

iary audio source can be connected and

the proper auxiliary cord to use.

• The volume and tone controls of the

auxiliary audio source can be adjusted

on the unit.

• In AUX mode, the volume setting is dif-

ferent from another mode.

5-65

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

Bluetooth

hands-free (Type A / Type B) (if equipped)

75RM090

(1) “TUNE/FLD PUSH SOUND” knob

(2) “VOL PUSH PWR” knob

(3) PRESET buttons

(4) BACK button

(5) Bluetooth

setup button (on control panel)

(1)

(5)

(2)

(3)

(4)

(1)

(5)

(2)

(3)

(4)

Type A

Type B

EXAMPLE

Steering switch

75RM061

(6) Bluetooth

setup button (on steering

wheel)

(7) OFF HOOK button

(8) ON HOOK button

(9) MUTE switch

(10) “VOL” switch

(9)

(10)

(8)

(7)

(6)

5-66

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

Phone registration

NOTE:

• Up to 5 phones can be registered.

• To set up a new phone, disconnect the

audio player from the unit. Connect the

audio player again after phone setup is

completed if necessary.

• When attempts to establish the pairing

fail within 60 seconds, the connecting

operation will be canceled. Try to estab-

lish the pairing again or refer to the man-

ual of the phone in use for how to

establish the pairing with the phone.

1) Press the Bluetooth

setup button (5)

or (6).

The Bluetooth

setup menu will be dis-

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Bluetooth”, and

press the knob (1) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Pairing”, and press the

knob (1) to determine the selection.

4) Select “My Car” from the Bluetooth

menu of the phone and establish the

pairing.

Refer to the manual of the phone in use

for further information.

5) Enter the passkey displayed on the unit

to the phone.

6) When the pairing with the phone is

established, automatic transfer of the

phonebook and the call history

becomes selectable. The automatic

transfer starts with “Yes” and it does not

with “No”.

7) Press ON HOOK button (8).

NOTE:

• When selecting “Go Back” or pressing

BACK button (4), the previous menu will

be displayed.

• When registering an additional phone,

repeat Step from 1).

Receiving a call

Press OFF HOOK button (7) to receive a

call.

Ending a call

Press ON HOOK button (8) to end a call.

Rejecting a call (only for supported

models)

Press ON HOOK button (8) to reject a

incoming call.

Mute of hands-free microphone

Press MUTE switch (9) to mute the micro-

phone. To cancel the mute, press MUTE

switch (9) again.

Adjusting the listening volume

• Turn “VOL PUSH PWR” knob (2) during

a call.

Turning it clockwise increases the vol-

ume; turning it counterclockwise

decreases the volume.

• Press “VOL” switch (10) during a call.

Pressing the switch up increases the vol-

ume; pressing the switch down

decreases the volume.

Adjusting the ring volume

• Turn “VOL PUSH PWR” knob (2) while a

call is coming in.

Turning it clockwise increases the vol-

ume; turning it counterclockwise

decreases the volume.

• Press “VOL” switch (10) during a call.

Pressing the switch up increases the vol-

ume; pressing the switch down

decreases the volume.

To use the hands-free function with this

unit, it is required to register the phone

in advance.

5-67

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

Adjusting the call or ringtone volume

Follow the instructions below to adjust the

call or ringtone volume.

1) Press the Bluetooth

setup button (5)

or (6).

The Bluetooth

setup menu will be dis-

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Telephone”, and

press the knob (1) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Sound Setting”, and press

the knob (1) to determine the selection.

4) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Call Volume” or “Ringtone

Volume”, and press the knob (1) to

determine the selection.

The current call or ringtone volume will

be displayed.

5) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select the desired call or ringtone

volume, and press the knob (1) to

determine the selection.

NOTE:

When selecting “Go Back” or pressing

BACK button (4), the previous menu will

be displayed.

Dialing using missed/incoming/

outgoing calls

Follow the instructions below to dial to the

previously dialed number again.

NOTE:

Up to 30 phone numbers of the latest calls

can be stored. (30 calls including missed,

received and dialed call)

1) Press OFF HOOK button (7).

The Bluetooth

phonebook menu will

be displayed.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “All Calls”, “Missed Calls”,

“Incoming Calls” or “Outgoing Calls”,

and press the knob (1) to determine the

selection.

To dial from the dialed history or the

received history, select “All Calls”,

“Missed Calls”, “Incoming Calls” or

“Outgoing Calls” respectively.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select the desired number, and

press the knob (1) to determine the

selection.

4) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Dial”, and press the knob

(1) or OFF HOOK button (7) to dial to

the selected number.

NOTE:

• When selecting “Go Back” or pressing

BACK button (4), the previous menu will

be displayed.

• Pressing “Confirm” after selecting “Add

Speed Dial” can register the selected

number in the speed dial.

• Pressing “Confirm” after selecting

“Delete” can delete the selected number

from the call history.

Deletion of call history

Follow the instructions below to delete a

missed/incoming/outgoing call history.

1) Press the Bluetooth

setup button (5)

or (6).

The Bluetooth

setup menu will be dis-

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Telephone”, and

press the knob (1) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Phonebook”, and

press the knob (1) to determine the

selection.

4) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Delete History”, and press

the knob (1) to determine the selection.

5) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Missed Calls”, “Incoming

Calls”, or “Outgoing Calls”, and press

the knob (1) to determine the selection.

6) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select a number to be deleted or

“ALL”, and press the knob (1) to deter-

mine the selection.

5-68

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

7) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Delete?” or “Delete All?”,

and press the knob (1) to determine the

selection.

8) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Confirm”, and press the

knob (1) to complete the deletion.

NOTE:

When selecting “Go Back” or pressing

BACK button (4), the previous menu will

be displayed.

Registration in Phonebook

Follow the instructions below to register

phone numbers in the Phonebook of the

unit.

1) Press the Bluetooth

setup button (5)

or (6).

The Bluetooth

setup menu will be dis-

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Telephone”, and

press the knob (1) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Phonebook”, and

press the knob (1) to determine the

selection.

4) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Add Contacts”, and press

the knob (1) to determine the selection.

5) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Overwrite All” or “Add One

Contact”, and press the knob (1) to

determine the selection.

“Rewrite All (MAX1000): Ok?” or “Rest

of Memory XXXX: Ok?” will be dis-

played.

6) Press or turn “TUNE/FLD PUSH

SOUND” knob (1) to select “Confirm”,

and press the knob (1) to determine the

selection.

7) Transfer contacts from the phone.

When the registration is completed, the

“Setup Phonebook” will be displayed.

NOTE:

• When selecting “Go Back” or pressing

BACK button (4), the previous menu will

be displayed.

• Up to 1000 numbers can be registered in

Phonebook.

Transfer of call history (Call History)

Follow the instructions below to transfer

call history of the registered phone.

1) Press the Bluetooth

setup button (5)

or (6).

The Bluetooth

setup menu will be dis-

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Telephone”, and

press the knob (1) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Call History”, and press

the knob (1) to determine the selection.

4) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Overwrite Call History?”,

and press the knob (1) to determine the

selection.

5) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Confirm”, and press the

knob (1) to transfer the call history from

the phone.

NOTE:

When selecting “Go Back” or pressing

BACK button (4), the previous menu will

be displayed.

5-69

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

Automatic transfer of phonebook/call

history

You can select whether or not the device

transfers the phonebook and the call his-

tory automatically when the phone is regis-

tered.

Follow the instructions below to select.

1) Press the Bluetooth

setup button (5)

or (6).

The Bluetooth

setup menu will be dis-

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Telephone”, and

press the knob (1) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “”, and press the

knob (1) to determine the selection.

4) Pressing “TUNE/FLD PUSH SOUND”

knob (1) switches between “

On” and “ Off”.

5) Selecting “Go Back” or pressing the

BACK button (4) stores displayed set-

ting and the previous menu is dis-

played.

Making a call by phonebook

Follow the instructions below to dial a num-

ber registered in phonebook.

1) Press OFF HOOK button (7).

The Bluetooth

phonebook menu will

be displayed.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Phonebook”, and press

the knob (1) to determine the selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select the initial of the name you

would like to make a call, and press the

knob (1) to determine the selection.

The registered numbers will be dis-

played in sequence. If names have

been registered together with numbers,

the names will be displayed.

Turn “TUNE/FLD PUSH SOUND” knob

(1) to select the name you would like to

make a call, and press the knob (1) to

determine the selection.

4) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Dial”, and press the knob

(1) or OFF HOOK button (7).

The displayed number or the number

registered with the displayed name will

be dialed.

Deletion of registered data (Delete

Entry)

Follow the instructions below to delete a

number registered in phonebook.

1) Press the Bluetooth

setup button (5)

or (6).

The Bluetooth

setup menu will be dis-

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Telephone”, and

press the knob (1) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Phonebook”, and

press the knob (1) to determine the

selection.

4) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Delete Contacts”, and

press the knob (1) to determine the

selection.

5) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select the initial of the name you

would like to delete or “ALL”, and press

the knob (1) to determine the selection.

Turn “TUNE/FLD PUSH SOUND” knob

(1) to select the name you would like to

delete, and press the knob (1) to deter-

mine the selection.

6) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Delete?” or “Delete All?”,

and press the knob (1) to determine the

selection.

7) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Confirm”, and press the

knob (1) to complete the deletion.

5-70

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

NOTE:

When selecting “Go Back” or pressing

BACK button (4), the previous menu will

be displayed.

Registration in speed dial

Follow the instructions below to assign a

number to one of PRESET buttons (3) to

use as the speed dial.

1) Press the Bluetooth

setup button (5)

or (6).

The Bluetooth

setup menu will be dis-

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Telephone”, and

press the knob (1) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Phonebook”, and

press the knob (1) to determine the

selection.

4) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Add Speed Dial”, and

press the knob (1) to determine the

selection.

5) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select the initial of the name you

would like to register in speed dial, and

press the knob (1) to determine the

selection.

The registered numbers will be dis-

played in sequence. If names have

been registered together with numbers,

the names will be displayed.

Turn “TUNE/FLD PUSH SOUND” knob

(1) to select the name you would like to

knob (1) to determine the selection.

6) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Choose Preset”, and

press one of PRESET buttons (3) to

which the selected number is to be

assigned. If a number is already

assigned to the selected button, a con-

firmation message will be displayed.

Turn “TUNE/FLD PUSH SOUND” knob

(1) to select a confirmation message,

and press the knob (1) to complete the

assignment.

Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Confirm”, and press the

knob (1) to complete the assignment.

When the assignment is completed, the

“Setup Phonebook” will be displayed.

NOTE:

When selecting “Go Back” or pressing

BACK button (4), the previous menu will

be displayed.

One-touch call (Speed dial)

Follow the instructions below to dial the

number assigned to each of the PRESET

buttons (3).

1) Press OFF HOOK button (7).

The Bluetooth

phonebook menu will

be displayed.

Pressing one of PRESET buttons (3)

can skip step 2) and the 1st line of step

3).

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Speed Dials”, and press

the knob (1) to determine the selection.

3) Press one of PRESET buttons (3).

The assigned number will be displayed.

If no number is assigned, “No Entry” is

displayed.

4) Press OFF HOOK button (7).

The selected number will be dialed.

5-71

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

Deletion of speed dial (Del Speed Dial)

Follow the instructions below to delete the

number assigned for the speed dial.

1) Press OFF HOOK button (7).

The Bluetooth

phonebook menu will

be displayed.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Speed Dials”, and press

the knob (1) to determine the selection.

3) Press one of PRESET buttons (3) to

which the number to be deleted is

assigned.

If the number is not registered, “No

Entry” is displayed.

4) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Delete”, and press the

knob (1) to determine the selection.

5) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Del Speed Dial”, and

press the knob (1) to determine the

selection.

6) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Confirm”, and press the

knob (1) to complete the deletion.

NOTE:

When selecting “Go Back” or pressing

BACK button (4), the previous menu will

be displayed.

Display of device data (Device Name)

Follow the instructions below to display the

BD (Bluetooth

Device) address and

device name.

1) Press the Bluetooth

setup button (5)

or (6).

The Bluetooth

setup menu will be dis-

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Bluetooth”, and

press the knob (1) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Bluetooth Info”, and press

the knob (1) to determine the selection.

4) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Device Name” or “Device

Address”, and press the knob (1) to dis-

play the device name or the BD (Blue-

tooth

Device) address.

NOTE:

When selecting “Go Back” or pressing

BACK button (4), the previous menu will

be displayed.

Reset to the factory defaults

Follow the instructions below to reset all

the settings to the factory defaults.

1) Press the Bluetooth

setup button (5)

or (6).

The Bluetooth

setup menu will be dis-

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Bluetooth”, and

press the knob (1) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Initialize”, and press the

knob (1) to determine the selection.

4) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “All Initialize”, and press

the knob (1) to determine the selection.

5) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Confirm”, and press the

knob (1) to start the reset.

NOTE:

When selecting “Go Back” or pressing

BACK button (4), the previous menu will

be displayed.

5-72

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

Selection of phone (Select Phone)

Follow the instructions below to select a

phone to be paired with from the registered

phones.

1) Press the Bluetooth

setup button (5)

or (6).

The Bluetooth

setup menu will be dis-

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Bluetooth”, and

press the knob (1) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “List Phone”, and press the

knob (1) to determine the selection.

4) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select a phone to be paired with,

and press the knob (1) to determine the

selection.

5) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Select”, and press the

knob (1) to determine the selection.

NOTE:

• When selecting “Go Back” or pressing

BACK button (4), the previous menu will

be displayed.

• The Bluetooth

ready audio device will

be disconnected when the phone is

selected.

List of phones (List Phones)

Follow the instructions below to display the

names of the registered phones in

sequence.

1) Press the Bluetooth

setup button (5)

or (6).

The Bluetooth

setup menu will be dis-

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Bluetooth”, and

press the knob (1) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “List Phone”, and press the

knob (1) to determine the selection.

The names of the registered phones

are displayed in sequence.

NOTE:

When selecting “Go Back” or pressing

BACK button (4), the previous menu will

be displayed.

Passkey setting (Set Passkey)

Follow the instructions below to set the

security number (passkey).

1) Press the Bluetooth

setup button (5)

or (6).

The Bluetooth

setup menu will be dis-

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Bluetooth”, and

press the knob (1) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Passkey”, and press the

knob (1) to determine the selection.

4) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Enter New Passkey”, and

press the knob (1) to determine the

selection.

5) Press or turn “TUNE/FLD PUSH

SOUND” knob (1) to select “Confirm”.

6) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select a number for the first digit,

and press the knob (1) to determine the

selection. Select and determine num-

bers for the second, third and fourth

digits in order in the same manner.

When not entering up to the eighth

digit, enter blanks for the successive

digits.

7) Press “TUNE/FLD PUSH SOUND”

knob (1) to determine the passkey set-

ting.

NOTE:

When selecting “Go Back” or pressing

BACK button (4), the previous menu will

be displayed.

5-73

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

Deletion of phone information (Delete

Phone)

Follow the instructions below to delete the

registered phone information.

1) Press the Bluetooth

setup button (5)

or (6).

The Bluetooth

setup menu will be dis-

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Bluetooth”, and

press the knob (1) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “List Phone”, and press the

knob (1) to determine the selection.

4) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select a phone to be deleted, and

press the knob (1) to determine the

selection.

5) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Delete”, and press the

knob (1) to determine the selection.

6) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Delete?”, and press the

knob (1) to determine the selection.

7) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Confirm”, and press the

knob (1) to determine the selection.

NOTE:

When selecting “Go Back” or pressing

BACK button (4), the previous menu will

be displayed.

BT function on/off (BT Power)

Follow the instructions below to turn on/off

the Bluetooth

function.

1) Press the Bluetooth

setup button (5)

or (6).

The Bluetooth

setup menu will be dis-

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Bluetooth”, and

press the knob (1) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “BT Power”, and press the

knob (1) to determine the selection.

4) Press “TUNE/FLD PUSH SOUND”

knob (1) to select “BT Power On” or “BT

Power Off”.

NOTE:

• When the BT function is turned off, the

connection between this unit and the

registered phone in use will be discon-

nected.

• When selecting “Go Back” or pressing

BACK button (4), the previous menu will

be displayed.

5-74

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

Bluetooth

audio (Type A / Type B) (if equipped)

75RM091

(2)

(7)

(4)

(3)

(1)

(5) (6)

(2)

(7)

(4)

(3)

(1)

(5) (6)

Type A

Type B

EXAMPLE

Steering switch

75RM062

Display

(1) “MEDIA” button

(2) “TUNE/FLD PUSH SOUND” knob

(3) UP button

(4) DOWN button

(5) “DISP” button

(6) BACK button

(7) Bluetooth

setup button (on control

panel)

(8) Bluetooth

setup button (on steering

wheel)

(A) Track number

(B) Play time

(8)

(B)

(A)

5-75

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

Registration of audio devices

NOTE:

• To set up a new audio player, disconnect

the phone from the unit. Connect the

phone after audio player setup is com-

pleted if necessary.

• When attempts to establish the pairing

fail within 60 seconds, the connecting

operation will be canceled. Try to estab-

lish the pairing again or refer to the audio

player manual for assistance with the

pairing process.

1) Press the Bluetooth

setup button (7)

or (8).

The Bluetooth

setup menu will be dis-

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select “Setup Bluetooth”, and

press the knob (2) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select “Pairing”, and press the

knob (2) to determine the selection.

4) Select “My Car” from the Bluetooth

menu of the audio player and establish

the pairing.

Refer to the manual of the audio player

in use for further information.

5) Enter the passkey displayed on the unit

to the audio player.

NOTE:

• When selecting “Go Back” or pressing

BACK button (6), the previous menu will

be displayed.

• When registering additional audio

devices, repeat Step from 1).

Selecting Bluetooth

audio mode

Press “MEDIA” button (1).

Each time the button is pressed, the mode

will change as follows:

Selecting a group (only for supported

models)

Turn “TUNE/FLD PUSH SOUND” knob (2)

to select a group.

Selecting a track

• Press UP button (3) to listen to the next

track.

• Press DOWN button (4) twice to listen to

the previous track.

When DOWN button (4) is pressed

once, the track currently being played

will start from the beginning again.

Fast forwarding/rewinding a track

• Hold down UP button (3) to fast forward

the track.

• Hold down DOWN button (4) to fast

rewind the track.

NOTE:

Some functions may not be available

depending on Bluetooth

audio.

Display change

Press “DISP” button (5).

Each time the button is pressed, display

will change as follows:

NOTE:

If text data contains more than 16 charac-

ters, “>” mark will appear at the right end.

Holding down “DISP” button (5) for 1 sec-

ond or longer can display the next page.

To use Bluetooth

ready audio devices

with this unit, it is required to register the

devices.

USB (iPod

) (if equipped)

Bluetooth

audio (if equipped)

AUX (if equipped)

Play time

Track name

Artist name

Album name

5-76

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

Selection of audio device (Select Audio)

Follow the instructions below to select an

audio device to be paired with from the

registered audio devices.

1) Press the Bluetooth

setup button (7)

or (8).

The Bluetooth

setup menu will be dis-

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select “Setup Bluetooth”, and

press the knob (2) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select “List Audio”, and press the

knob (2) to determine the selection.

4) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select an audio device to be

used, and press the knob (2) to deter-

mine the selection.

5) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select “Select”, and press the

knob (2) to determine the selection.

NOTE:

• When selecting “Go Back” or pressing

BACK button (6), the previous menu will

be displayed.

• The phone will be disconnected when

the Bluetooth

ready audio device is

selected.

List of audio devices (List Audio)

Follow the instructions below to display the

names of the registered audio devices in

sequence.

1) Press the Bluetooth

setup button (7)

or (8).

The Bluetooth

setup menu will be dis-

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select “Setup Bluetooth”, and

press the knob (2) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select “List Audio”, and press the

knob (2) to determine the selection.

The names of registered audio devices

will be displayed in sequence.

NOTE:

When selecting “Go Back” or pressing

BACK button (6), the previous menu will

be displayed.

Passkey setting (Set Passkey)

Follow the instructions below to set the

security number (Passkey).

1) Press the Bluetooth

setup button (7)

or (8).

The Bluetooth

setup menu will be dis-

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select “Setup Bluetooth”, and

press the knob (2) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select “Passkey”, and press the

knob (2) to determine the selection.

4) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select “Enter New Passkey”, and

press the knob (2) to determine the

selection.

5) Press or turn “TUNE/FLD PUSH

SOUND” knob (2) to select “Confirm”.

6) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select a number for the first digit,

and press the knob (2) to determine the

selection. Select and determine num-

bers for the second, third and fourth

digits in order in the same manner.

When not entering up to the eighth

digit, enter blanks for the successive

digits.

7) Press “TUNE/FLD PUSH SOUND”

knob (2) to determine the passkey set-

ting.

NOTE:

When selecting “Go Back” or pressing

BACK button (6), the previous menu will

be displayed.

5-77

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

Deletion of audio device information

(Delete Audio)

Follow the instructions below to delete the

registered audio device information.

1) Press the Bluetooth

setup button (7)

or (8).

The Bluetooth

setup menu will be dis-

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select “Setup Bluetooth”, and

press the knob (2) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select “List Audio”, and press the

knob (2) to determine the selection.

4) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select an audio device to be

deleted, and press the knob (2) to

determine the selection.

5) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select “Delete”, and press the

knob (2) to determine the selection.

6) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select “Delete?”, and press the

knob (2) to determine the selection.

7) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select “Confirm”, and press the

knob (2) to complete the deletion.

NOTE:

When selecting “Go Back” or pressing

BACK button (6), the previous menu will

be displayed.

Disclaimer for Bluetooth

function

• Depending on compatibility of mobile

phone models, no Bluetooth

function

can be used, or some Bluetooth

func-

tions may be restricted.

• Connectivity or voice quality may get

affected depending on circumstances.

• After the ignition switch is turned to “ON”

position or the engine switch is pressed

to change the ignition mode to ON, the

audio system takes few seconds to

detect and connect to the Bluetooth

device (if already paired).

Remote audio controls (if equipped)

Controlling basic functions of the audio

system is available using the switches on

the steering wheel.

75RM063

(4)

(2)

(1) (3)

5-78

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

Adjusting the volume

• To increase the volume, press the “VOL”

switch (1) up. The volume will continue

to increase until the switch is released.

• To decrease the volume, press the

“VOL” switch (1) down. The volume will

continue to decrease until the switch is

released.

• To mute the sound, press the switch (2).

Selecting the mode

Press the switch (3).

Each time the button is pressed, the mode

will change as follows:

It is possible to turn on the audio system

by pressing the switch (3).

Selecting the radio station (AM, FM1,

FM2, DAB1, DAB2 mode)

• To select the next preset station, press

“>” of the switch (4) only for a moment.

• To select the previous preset station,

press “<” of the switch (4) only for a

moment.

• To scan a higher frequency radio station,

press “>” of the switch (4) for 1 second

or longer.

• To scan a lower frequency radio station,

press “<” of the switch (4) for 1 second

or longer.

Selecting the track (CD, USB (iPod

Bluetooth

audio mode)

• To skip to the next track, press “>” of the

switch (4) only for a moment.

• To skip to the previous track, press “<” of

the switch (4) twice only for a moment.

When the switch (4) is pushed down

once only for a moment, the track cur-

rently being played will start from the

beginning again.

Fast forwarding/rewinding a track

• To fast forward a track, press “>” of the

switch (4) for 1 second or longer.

• To fast rewind a track, press “<” of the

switch (4) for 1 second or longer.

AM (Radio)

FM1 (Radio)

FM2 (Radio)

DAB1 (if equipped)

DAB2 (if equipped)

Bluetooth

audio (if equipped)

AUX (if equipped)

USB (iPod

) (if equipped)

5-79

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

Anti-theft feature

75RM092

(1) VOL PUSH PWR” knob

(2) PRESET buttons ([1] to [6])

(3) UP button

(4) “TUNE/FLD PUSH SOUND” knob

(3)

(4)

(2)

(1)

(3)

(4)

(2)

(1)

(3)

(4)

(2)

(1)

Type A

Type B

EXAMPLE

Type C

The anti-theft function is intended to dis-

courage thefts. For example, when the

audio system is installed in another vehi-

cle, it will become unable to operate.

This function works by entering a Personal

Identification Number (PIN).

When the unit is disconnected from its

power source, such as when the audio

system is removed or the lead-acid battery

is disconnected, the unit will become inop-

erable until the PIN is reentered.

5-80

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

Setting the anti-theft function

1) Press “VOL PUSH PWR” knob (1) to

power off.

2) Hold down the buttons numbered [1]

and [6] of PRESET buttons (2) and

press “VOL PUSH PWR” knob (1).

“SECURITY” will be displayed.

3) Press UP button (3) and the button

numbered [1] of PRESET buttons (2)

simultaneously.

4) Enter a 4-digit number to be registered

as PIN using the buttons numbered [1]

- [4] of PRESET buttons (2).

5) Hold down “TUNE/FLD PUSH

SOUND” knob (4) for 1 second or lon-

ger to set the anti-theft function.

NOTE:

Take a note of the registered PIN and keep

it for the future use.

Canceling the anti-theft feature

To cancel the anti-theft function, delete the

registered PIN.

1) Press “VOL PUSH PWR” knob (1) to

power off.

2) Hold down the buttons numbered [1]

and [6] of PRESET buttons (2) and

press “VOL PUSH PWR” knob (1).

“PIN ENTRY” will be displayed.

3) Press UP button (3) and the button

numbered [1] of PRESET buttons (2)

simultaneously.

4) Enter a 4-digit number to be registered

as PIN using the buttons numbered [1]

- [4] of PRESET buttons (2).

5) Hold down “TUNE/FLD PUSH

SOUND” knob (4) for 1 second or lon-

ger to delete the registered PIN. The

indication “----” will be displayed and

the anti-theft function will be canceled.

NOTE:

To change your PIN, first delete your cur-

rent PIN, and then set a new one.

Confirming the Personal Identification

Number (PIN)

When the main power source is discon-

nected such as when the lead-acid battery

is replaced, etc, it is required to enter the

PIN to operate the unit again.

1) Set the ignition switch to “ACC” posi-

tion or the ignition mode to ON.

“SECURITY” will be displayed.

2) Press UP button (3) and the button

numbered [1] of PRESET buttons (2)

simultaneously.

3) Enter a 4-digit number to be registered

as PIN using the buttons numbered [1]

- [4] of PRESET buttons (2).

4) Hold down “TUNE/FLD PUSH

SOUND” knob (4) for 1 second or lon-

ger.

When the same PIN as registered is

entered, the power of the audio system

will be turned off automatically and it

will become operable again.

NOTE:

If an incorrect PIN is entered, “ERROR”

and the total number of incorrect entry

attempts will be displayed.

If an incorrect PIN is entered 10 times or

more, “HELP” will be displayed and the

audio system will become inoperable.

5-81

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

Troubleshooting

When encountering a problem, check and follow the instructions below.

If the described suggestions do not solve the problem, it is recommended to take the unit to your authorized SUZUKI dealer.

Problem Possible cause Possible solution

Common

Unable to operate The security function is on.

When “SECURITY” is displayed, enter

the PIN.

When “HELP” is displayed, contact your

authorized SUZUKI dealer.

Unable to turn on the power

(No sound is produced)

Fuse is blown. Contact your authorized SUZUKI dealer.

Radio

Much noise

It may not be exactly tuned in to the sta-

tion.

Tune it in exactly to the station.

Unable to receive by auto tuning

There may be no station emitting signals

powerful enough.

Pick up a station by manual tuning.

If AF is on, the unit searches for RDS sta-

tions only.

Turn off AF.

Sound skips or noise produced

The disc is dirty. Wipe the disc with a soft cloth.

The disc has a major scratch or is

warped.

Replace the disc with the one which has

no scratch and warp.

5-82

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

MP3/WMA/AAC

No playback

The disc contains unsupported formatted

data.

Check the file format.

Sound skips or noise produced

Sound skipping may occur when playing

VBR (Variable Bit Rate) files.

It is not recommended to play VBR files.

USB

Playback does not start when the USB

device is connected

There is no supported format file to play

on this unit.

Check the file format.

The current consumption of the USB

device exceeds 1.0 A.

Use a USB device with a current con-

sumption lower than 1.0 A.

Bluetooth

Pairing failed

The distance between this unit and the

Bluetooth

ready device is too far, or a

metallic object may be located between

the Bluetooth

ready device and this unit.

Change the location of the Bluetooth

ready device.

The Bluetooth

function of the Bluetooth

ready device is off.

Refer to the manual of the Bluetooth

ready device. (Some devices have the

power saving function that automatically

activates after a certain time.)

Unable to receive a call

Your current location may be out of ser-

vice area.

Drive your vehicle to the service area of

the phone.

The voice quality of hands-free is low

(Distortion, noise etc.)

Another wireless device may be located

near the unit.

Switch off the wireless device or keep it

away from the unit.

Problem Possible cause Possible solution

5-83

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

Error display messages

Display Possible cause Possible solution

“ERROR 1” The disc cannot be read.

Insert the disc with its label side up.

Check the disc if it is not warped or is free of flaws.

When “ERROR 1” does not disappear even when a nor-

mal disc is inserted, contact your dealer.

“ERROR 3”

The player developed an error of an

unidentified cause.

When the CD is in the unit, press the CD eject button to

remove the disc.

When the disc cannot be ejected, contact your dealer.

USB/iPod

“USB ERROR” The USB device is disconnected. Check the connection of the USB device.

“ERROR 2”

Impossible to communicate correctly with

the USB device.

Unplug the USB device and plug it again.

Check the USB device.

“ERROR 3” Inoperable due to an unidentified cause.

Unplug the USB device and plug it again.

When “ERROR 3” does not disappear, contact your

dealer.

“ERROR 4”

The current consumption of the USB

device exceeds 1.0 A.

Check the USB device.

5-84

OTHER CONTROLS AND EQUIPMENT

75RM4-01E

Bluetooth

“ERROR 1”

The player developed an error of an

unidentified cause.

Disconnect the Bluetooth

ready device and connect it

again.

When “ERROR 1” does not disappear, contact your

dealer.

“Connection Failed” Failed to establish pairing or connection Try to establish the pairing or connection again.

“Memory Full”

Reached the limit for the number of phone-

book data in transfer

Delete registered data of unnecessary number in phone-

book and try to transfer the register phone numbers in

the phonebook again.

“Not Available” Inoperable during driving Operate the system after pulling over your car.

Display Possible cause Possible solution

Other Controls and Equipment -> Audio system (Type A / Type B / Type C) (if equipped) for Your Suzuki Ignis SUV Second Generation (2016-2024)

Related Topics

Popular Owner Manuals

Latest Owner Manuals