Get Operating Your Vehicle -> Braking Guide for Suzuki S Cross SUV First Generation (2006-2012)

3-20

OPERATING YOUR VEHICLE

80J23-03E

To Change Cruising Speed

Using the accelerator pedal

To reset at a faster cruising speed, acceler-

ate to the desired speed using the acceler-

ator pedal and push the “SET/COAST”

switch (3). The new speed will be main-

tained.

Using the brake pedal

To reset at a slower cruising speed, decel-

erate to the desired speed using the brake

pedal and push the “SET/COAST” switch

(3). The new speed will be maintained.

NOTE:

When the brake pedal is depressed, the

“SET” indicator light goes off until reset the

cruising speed.

Using the cruise control switch

To reset at a faster cruising speed, press

repeatedly or hold in the “RES/ACC”

switch (4). Vehicle speed will steadily

increase. When you release the switch, the

new speed will be maintained.

To reset at a slower cruising speed, press

repeatedly or hold in the “SET/COAST”

switch (3) until the vehicle has slowed to

the desired speed, then release the switch.

The new speed will be maintained.

NOTE:

You can adjust the set speed by approxi-

mately 1.0 mph (1.6 km/h) by pushing a

cruise control switch quickly.

Cancellation of the Cruise Control

The “SET” indicator light will go off and the

cruise control will be canceled temporarily

with following procedures:

• Push the “CANCEL” switch (2).

• Depress the brake pedal.

• For manual transaxle, depress the clutch

pedal.

• For CVT, downshift from 3rd to 2nd in the

manual mode.

• The vehicle speed falls more than about

20 percent from the set speed.

• Any time the vehicle speed falls below

25 mph (40 km/h).

• When the vehicle skids and ESP

(if

equipped) is activated.

To resume the previously set speed, push

the “RES/ACC” switch (4) and turn on the

“SET” indicator light. Besides, the vehicle

speed has to be above 25 mph (40 km/h)

when the vehicle is not in the above condi-

tions.

To turn off the cruise control system, push

the “CRUISE” switch (1) and make sure

the “CRUISE” indicator light is off.

Also, if the malfunction indicator light in the

instrument cluster comes on or blinks, the

cruise control system will be turned off.

NOTE:

If you turn off the cruise control system, the

previously set speed in the memory is

cleared. Reset your cruising speed again.

Braking

60G165

The distance needed to bring any vehicle

to a halt increases with the speed of the

vehicle. The braking distance needed, for

example, at 60 km/h (37 mph) will be

approximately 4 times greater than the

braking distance needed at 30 km/h (19

mph). Start to brake the vehicle when there

is plenty of distance between your vehicle

and the stopping point, and slow down

gradually.

3-21

OPERATING YOUR VEHICLE

80J23-03E

Power-Assisted Brakes

Your vehicle has power-assisted brakes. If

power assistance is lost due to a stalled

engine or other failures, the system is still

fully operational on reserve power and you

can bring the vehicle to a complete stop by

pressing the brake pedal once and holding

it down. The reserve power is partly used

up when you depress the brake pedal and

reduces each time the pedal is pressed.

Apply smooth and even pressure to the

pedal. Do not pump the pedal.

Brake Assist System

When you slam the brakes on, the brake

assist system judges as an emergency

stop and provides more powerful braking

for a driver who cannot hold down the

brake pedal firmly.

NOTE:

If you quickly and forcefully depress the

brakes, you may hear a clicking sound in

the brake pedal. This is normal and indi-

cates that the brake assist system is acti-

vated properly.

Anti-Lock Brake System (ABS)

(if equipped)

ABS will help you avoid skidding by elec-

tronically controlling braking pressure. It

will also help you maintain steering control

when braking on slippery surfaces or when

braking hard.

The ABS works automatically, so you do

not need any special braking technique.

Just push the brake pedal down without

pumping. The ABS will operate whenever it

senses that the wheels are locking up.

You may feel the brake pedal pulsate while

the ABS is operating.

NOTE:

The ABS will not work if vehicle speed is

under about 6 km/h (4mph).

WARNING

If water gets into the brake drums,

brake performance may become poor

and unpredictable.

After driving through water or wash-

ing the underside of the vehicle, test

the brakes while driving at a slow

speed to see if they have maintained

their normal effectiveness. If the

brakes are less effective than normal,

dry them by repeatedly applying the

brakes while driving slowly until the

brakes have regained their normal

effectiveness.

WARNING

Even without reserve power in the

brake system, you can still stop the

vehicle by pressing the brake pedal

harder than normally required. How-

ever, the stopping distance may be

longer.

3-22

OPERATING YOUR VEHICLE

80J23-03E

65D451

(1) ABS warning light Type 1

(2) ABS warning light Type 2

(3) Brake system warning light

WARNING

• On some types of loose surfaces

(such as gravel, snow-covered

roads, etc.), the stopping distance

required for an ABS-equipped vehi-

cle may be slightly greater than for

a comparable vehicle with a con-

ventional brake system. With a

conventional brake system, skid-

ding tires are able to “plow” the

gravel or snow layer, shortening

the stopping distance. ABS mini-

mizes this resistance effect. Allow

for extra stopping distance when

driving on loose surfaces.

• On regular paved roads, some driv-

ers may be able to obtain slightly

shorter stopping distances with

conventional brake systems than

with ABS.

• In both of the above conditions,

ABS will still offer the advantage of

helping you maintain directional

control. However, remember that

ABS will not compensate for bad

road or weather conditions or poor

driver judgment. Use good judg-

ment and do not drive faster than

conditions will safely allow.

(1) (2)

(3)

WARNING

If the ABS warning light ((1) or (2)) on

the instrument panel comes on and

stays on while driving, there may be a

problem with the ABS system.

If this happens:

1) Pull off the road and stop care-

fully.

2) Turn the ignition switch to “LOCK”

and then start the engine again.

If the warning light comes on briefly

then turns off, the system is normal.

If the warning light still stays on,

have the system inspected by your

SUZUKI dealer immediately. If the

ABS system becomes inoperative,

the brake system will function as an

ordinary brake system that has no

ABS.

3-23

OPERATING YOUR VEHICLE

80J23-03E

How the ABS Works

A computer continuously monitors wheel

speed. The computer compares the

changes in wheel speed when braking. If

the wheels slow suddenly, indicating a

skidding situation, the computer will

change braking pressure several times

each second to prevent the wheels from

locking. When you start your vehicle or

when you accelerate after a hard stop, you

may hear a momentary motor or clicking

noise as the system resets or checks itself.

Electronic Stability Program

(ESP

) (if equipped)

ESP

is a registered trademark of Daimler

AG.

The Electronic Stability Program (ESP

)

helps to control the vehicle during corner-

ing if front wheels or rear wheels skid. It

also assists you in maintaining traction

while accelerating on loose or slippery

road surfaces. It does this by regulating the

engine’s output, and by selectively apply-

ing the brakes. In addition, ESP

helps to

avoid skidding by controlling braking pres-

sure.

WARNING

If the ABS warning light ((1) or (2))

and the Brake system warning light

(3) on the instrument panel simulta-

neously stay on or come on when

driving, both anti-lock function and

rear brake force control function (pro-

portioning valve function) of the ABS

system may have failed. This could

cause the rear wheels to skid or the

vehicle to spin during braking on a

slippery road or hard braking on a

dry paved road. If both warning lights

come on, drive carefully, avoiding

hard braking as much as possible,

and ask your SUZUKI dealer to

inspect the ABS system immediately.

WARNING

The ABS may not work properly if

tires or wheels other than those

specified in the owner’s manual are

used. This is because the ABS works

by comparing changes in wheel

speed. When replacing tires or

wheels, use only the size and type

specified in this owner’s manual.

WARNING

The ESP

cannot enhance the vehi-

cle’s driving stability in all situations

and does not control your vehicle’s

entire braking system. The ESP

can-

not prevent accidents, including

those resulting from excessive speed

in turns, or hydroplaning. Only a safe

and attentive driver can prevent acci-

dents. The capabilities of an ESP

equipped vehicle must never be used

as a substitute for careful driving.

Operating Your Vehicle -> Braking for Your Suzuki S Cross SUV First Generation (2006-2012)

Related Topics

Popular Owner Manuals

Latest Owner Manuals