2004-2009 Suzuki Swift 4 Door INSPECTION AND MAINTENANCE -> Bulb replacement User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

INSPECTION AND MAINTENANCE -> Bulb replacement for Your Suzuki Swift 4 Door First generation (2004-2009)

INSPECTION AND MAINTENANCE  
Headlight aiming  
Bulb replacement  
Since special procedures are required, ask  
an authorized SUZUKI dealer for this job.  
CAUTION  
• Light bulbs can be hot enough to  
burn your finger right after turning  
off lights. This is true especially for  
halogen headlight bulbs. Replace  
the bulbs after they become cool  
enough.  
OK  
BLOWN  
• The headlight bulbs are filled with  
pressurized halogen gas. They can  
burst and injure you if they are hit  
or dropped. Handle them carefully.  
• To avoid injury by sharp-edged  
parts of the body, wear gloves and  
a long-sleeved shirt when replacing  
light bulbs.  
81A283  
WARNING  
Always replace a blown fuse with a  
fuse of the correct amperage. Never  
use a substitute such as aluminum  
foil or wire to replace a blown fuse. If  
you replace a fuse and the new one  
blows in a short period of time, you  
may have a major electrical problem.  
Have your vehicle inspected immedi-  
ately by an authorized SUZUKI dealer.  
NOTICE  
The oils from your skin may cause a  
halogen bulb to overheat and burst  
when the lights are on. Grasp a new  
bulb with a clean cloth.  
NOTICE  
Frequent bulb replacement indicates  
the need for an inspection of the elec-  
trical system. This should be carried  
out by an authorized SUZUKI dealer.  
7-38  
52RM0-01E  
INSPECTION AND MAINTENANCE  
Headlights  
LED type  
(4)  
(2)  
Since special procedures are required, it is  
recommended that you take your vehicle  
to an authorized SUZUKI dealer for bulb  
replacement.  
(3)  
Halogen type  
(1)  
52RM70320  
52RM70230  
1) Open the engine food while the engine  
is stopped. Disconnect the coupler (2).  
Remove the sealing rubber (3) by pull-  
ing the grip (4).  
NOTE:  
You can see the position of retaining spring  
from the hole of headlight.  
52RM70220  
(1) Bulb  
(5)  
52RM70330  
2) Push the retaining spring (5) forward  
and unhook it. Then remove the bulb.  
Install a new bulb in the reverse order  
of removal.  
7-39  
52RM0-01E  
INSPECTION AND MAINTENANCE  
EXAMPLE  
Vehicle with the LED headlights  
Front turn signal light and  
front position light  
For LED position light (if equipped), it is  
recommended that you take your vehicle  
to an authorized SUZUKI dealer for bulb  
replacement since special procedures are  
required.  
(1)  
Vehicle with the halogen headlights  
68PH00732  
52RM70140  
(1)  
1) Open the engine hood while the engine  
is stopped. To remove the bulb holder  
of the front turn signal light or the front  
position light from the light housing,  
turn the holder counterclockwise and  
pull it out.  
(1) Front turn signal light  
(2)  
52RM70240  
(1) Front turn signal light  
(2) Front position light (if equipped)  
7-40  
52RM0-01E  
INSPECTION AND MAINTENANCE  
EXAMPLE  
Side turn signal light  
Front fog light (if equipped)  
Outside rearview mirror type  
1) Start the engine. Turn the steering  
wheel to the opposite side of the fog  
light to be replaced to replace the bulb  
easily. Then turn off the engine.  
LED is used. It is recommended that you  
take your vehicle to an authorized SUZUKI  
dealer for bulb replacement since special  
procedures are required.  
(2)  
EXAMPLE  
Fender type  
(3)  
(4)  
(1)  
(1)  
68PM00721  
(3) Removal  
(4) Installation  
2) To remove the bulb of the front turn sig-  
nal light (1) from the bulb holder, push  
in the bulb and turn it counterclockwise.  
To install a new bulb, push it in and turn  
it clockwise.  
(2)  
52RM70150  
2) Remove the clip (1) and screws (2) at  
the bottom of bumper.  
64J195  
To remove and install the bulb of the  
front position light (2), simply pull out or  
push in the bulb.  
Since the bulb is built-in type, replace it as  
the light assembly. Remove the light  
assembly by sliding the light housing left-  
ward with your finger.  
For removing the clip, use a flat blade  
screwdriver as show in the illustration.  
7-41  
52RM0-01E  
INSPECTION AND MAINTENANCE  
Rear combination light  
Daytime running light  
For LED tail / brake light (if equipped), it is  
recommended that you take your vehicle  
to an authorized SUZUKI dealer for bulb  
replacement since special procedures are  
required.  
LED type  
Since special procedures are required, it is  
recommended that you take your vehicle  
to an authorized SUZUKI dealer for bulb  
replacement.  
Bulb type  
(2)  
1) Perform step 1) to 3) of “Front fog light  
(if equipped)” in this section.  
(1)  
52RM70250  
3) Open the end of the cover inside the  
fender.  
52RM70160  
(4)  
(3)  
(2)  
1) With the tailgate opened, remove the  
bolts (1) and pull the light housing (2)  
firmly to the rearward.  
(1)  
52RM70340  
2) Disconnect the coupler (1) from the  
bulb holder (2) by pushing the lock  
release. Then, turn the bulb holder  
counterclockwise and remove it from  
the light case (3).  
(3)  
52R70140  
4) Disconnect the coupler (3) by pushing  
the lock release. Turn the bulb holder  
(4) counterclockwise and remove it.  
7-42  
52RM0-01E  
INSPECTION AND MAINTENANCE  
EXAMPLE  
EXAMPLE  
EXAMPLE  
(5)  
(4)  
(3)  
(5) / (6) / (7)  
(6)  
(8)  
(9)  
(7)  
52RM70170  
52RM70180  
2) Remove the wire (3) from a clamp (4).  
3) To remove the bulb holder of the bulb  
type tail/brake light (5) (if equipped), the  
rear turn signal light (6) or the reversing  
light (7) from the light housing, turn the  
holder counterclockwise and pull it out.  
(8) Removal  
(9) Installation  
4) To remove and install the bulb of the  
bulb type tail/brake light (5) (if  
equipped), the rear turn signal light (6)  
or the reversing light (7), simply pull out  
or push in the bulb.  
52RM70190  
NOTE:  
When reinstalling the light housing, check  
that the clips are properly attached.  
7-43  
52RM0-01E  
INSPECTION AND MAINTENANCE  
Rear fog light  
License plate light  
(2)  
(1)  
76MH0A126  
(1)  
2) To remove and install the bulb of the  
license plate light (2), simply pull out or  
push in the bulb.  
52RM70070  
52RM70350  
1) Remove the cover (1) by turning it  
counterclockwise.  
1) Remove the clips (1) in rear bumper by  
using a flat blade screwdriver as shown  
in the illustration.  
High-mount stop light  
LED is used. It is recommended that you  
take your vehicle to an authorized SUZUKI  
dealer for bulb replacement since special  
procedures are required.  
(2)  
52RM70360  
7-44  
52RM0-01E  
INSPECTION AND MAINTENANCE  
2) Turn rear bumper by hand as shown in  
the illustration and remove harness  
clamp (2).  
4) Turn the bulb holder counterclockwise  
and pull it out.  
Interior light  
Remove the lens by using a flat-bladed  
screwdriver covered with a soft cloth as  
shown. To install it, simply push it back in.  
EXAMPLE  
Front  
(4)  
(5)  
(6)  
(3)  
61MM0B084  
52RM70370  
(5) Removal  
(6) Install  
3) Remove the nuts (3) and then push  
rear fog light housing rearward.  
76MH0A139  
5) To remove the bulb of the rear fog light  
(4) from bulb holder, push in the bulb  
and turn it counterclockwise. To install a  
new bulb, push it in and turn it clock-  
wise.  
52RM70380  
7-45  
52RM0-01E  

Related Topics

INSPECTION AND MAINTENANCE
Maintenance schedule Periodic maintenance schedule Drive belt Engine oil and filter Engine coolant Air cleaner Spark plugs Gear oil Clutch pedal Continuously Variable Transaxle (CVT) fluid Brakes Steering wheel Tires Battery Fuses Headlight aiming Wiper blades Windshield washer fluid Air conditioning system

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot