2010-2015 Suzuki Swift 4 Door INSPECTION AND MAINTENANCE -> Bulb Replacement User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

INSPECTION AND MAINTENANCE -> Bulb Replacement for Your Suzuki Swift 4 Door Second Generation (2010-2015)

Battery: 9  
Fuses: 7  
INSPECTION AND MAINTENANCE  
Center Interior Light  
Headlight Aiming  
Since special procedures are required, we  
recommend you take your vehicle to your  
SUZUKI dealer for headlight alignment.  
Bulb Replacement  
CAUTION  
• Light bulbs can be hot enough to  
burn your finger right after being  
turned off. This is true especially  
for halogen headlight bulbs.  
Replace the bulbs after they  
become cool enough.  
• The headlight bulbs are filled with  
pressurized halogen gas. They can  
burst and injure you if they are hit  
or dropped. Handle them carefully.  
60G115  
NOTICE  
Pull down the lens by using a flat blade  
screwdriver covered with a soft cloth as  
shown. To install it, simply push it back in.  
The bulb can be removed by simply pulling  
it out. When replacing the bulb, make sure  
that the contact springs are holding the  
bulb securely.  
The oils from your skin may cause a  
halogen bulb to overheat and burst  
when the lights are on. Grasp a new  
bulb with a clean cloth.  
NOTICE  
Frequent replacement of a bulb indi-  
cates the need for an inspection of  
the electrical system. This should be  
carried out by your SUZUKI dealer.  
7-27  
58MS0-14E  
Fuses: 7  
INSPECTION AND MAINTENANCE  
Side Turn Signal Light (if equipped)  
Headlight  
(3)  
(2)  
(1)  
68LM713  
64J195  
NOTE:  
As the bulb is built-in type, the light assem-  
bly must be replaced. Remove the light  
assembly by sliding the light housing left-  
ward with your finger.  
You can see the position of retaining spring  
(3) from the hole of headlight.  
(3)  
80JM069  
Open the engine food. Disconnect the cou-  
pler (1). Remove the sealing rubber (2).  
Push the retaining spring (3) forward and  
unhook it. Then remove the bulb. Install a  
new bulb in the reverse order of removal.  
7-28  
58MS0-14E  
Fuses: 7  
INSPECTION AND MAINTENANCE  
Bulb  
EXAMPLE  
Front turn signal light (1)  
Front position light (2)  
Other General Lights  
Bulb holder  
EXAMPLE  
(1)  
(2)  
(2)  
(1)  
(1)  
(3)  
(4)  
(2)  
(1)  
(2)  
54G124  
68LM714  
(3) Removal  
(4) Installation  
54G123  
(1) Removal  
(2) Installation  
There are two types of bulb, “Full glass  
type” (1) and “Glass/metal type” (2).  
To remove a bulb holder from a light hous-  
ing, turn the holder counterclockwise and  
pull it out. To install the holder, push the  
holder in and turn it clockwise.  
To remove and install a full glass type bulb  
(1), simply pull out or push in the bulb.  
To remove a glass metal type bulb (2) from  
a bulb holder, push in the bulb and turn it  
counterclockwise. To install a new bulb,  
push it in and turn it clockwise.  
You can access the individual bulb or bulb  
holders as follows.  
7-29  
58MS0-14E  
Fuses: 7  
Bulb Replacement: 7  
INSPECTION AND MAINTENANCE  
Front fog light (if equipped)  
Rear combination light  
(tail, stop, turn signal, etc.)  
EXAMPLE  
1) Start the engine. Turn the steering  
wheel to the opposite side of the replac-  
ing fog light to replace the bulb easily.  
Then turn off the engine.  
(1)  
EXAMPLE  
(1)  
(1)  
(2)  
(2)  
80JM071  
3) Open the fender cover. Disconnect the  
coupler with pushing the lock release.  
Turn the bulb holder counterclockwise  
and remove it.  
68LM704  
Remove the screw (1). Remove the combi-  
nation light (2) by pulling it outside.  
68LM715  
2) Insert a flat blade screwdriver into the  
hole (2) and remove the clips (1) by  
twist the driver as shown in the illustra-  
tion.  
7-30  
58MS0-14E  
Bulb Replacement: 7  
INSPECTION AND MAINTENANCE  
License plate light  
High-mount stop light  
(3)  
(2)  
(2)  
(1)  
63J127  
68LM705  
80J100  
2) Close the tailgate. Remove a high-  
mount stop light housing (2) from the  
tailgate.  
To open the trim (1), insert a flat blade  
screwdriver into the hole (3) and remove  
the clips (2) by twist the driver as shown in  
the illustration.  
To remove a high-mount stop light housing  
the following procedure:  
1) Open the tailgate, and remove the nuts  
(1) as shown in the illustration.  
68LM722  
7-31  
58MS0-14E  

Related Topics

Popular Owner Manuals