Get OPERATING YOUR VEHICLE -> Keyless Push Start System Guide for Suzuki Swift 4 Door Second Generation (2010-2015)

Using the Transaxle: 10

Braking: 6

OPERATING YOUR VEHICLE

Manual transaxle – Provided you have the

keyless push start system remote control-

ler with you, the engine automatically

starts when you press the engine switch to

select this ignition mode after shifting to

“N” (Neutral) and depressing the brake and

clutch pedals.

Engine Switch Illumination

The engine switch is illuminated (lit) in the

following situations:

• The driver’s door is open (only when the

engine is not in operation).

• For 15 seconds after the driver’s door is

closed (only when the engine is not in

operation).

• The position lights are on.

The illumination will fade out when it is not

required.

Keyless Push Start System

Provided the keyless push start system

remote controller is within the “interior

workable area” (Refer to the related expla-

nation in this section), you can use the

engine switch for starting the engine and

selecting an ignition mode (“ACC” or

“ON”). In addition, the following functions

can be used:

NOTE:

You do not need to keep the engine switch

pressed to start the engine.

• Keyless entry function. Refer to “Keyless

Push Start System Remote Controller” in

the “BEFORE DRIVING” section for

details.

• Locking and unlocking doors (including

the tailgate) using a request switch.

Refer to “Keyless Push Start System

Remote Controller” in the “BEFORE

DRIVING” section for details.

NOTICE

Do not leave the engine switch in the

“ACC” or “ON” mode when the

engine is not running. Avoid using

the radio or other electric accesso-

ries for a long time when the engine

switch is in the “ACC” or “ON” mode

when the engine is not running, oth-

erwise the battery may discharge.

• Immobilizer (anti-theft) function. Refer to

“Immobilizer System” in the “BEFORE

DRIVING” section for details.

NOTE:

• The steering lock may not be released if

some load is acting on the steering

wheel. If this happens, turn the steering

wheel to the right or left to relieve it from

the load before you press the engine

switch again to change to the desired

ignition mode.

• In the presence of strong radio signals or

noise, you may not be able to change

the ignition mode to “ACC” or “ON” or to

start the engine using the engine switch.

3-6

58MS0-14E

Braking: 6

OPERATING YOUR VEHICLE

Selection of Ignition Modes

Press the engine switch to select the

“ACC” or “ON” mode as follows when you

use an electric accessory or check the

operation of instruments without running

the engine.

CVT

Gearshift

lever in

1) Bring the keyless push start system

remote controller with you and sit in the

driver’s seat.

LOCK

(OFF)

ACC

(Audio equipment)

Gearshift lever in a

position other than

2) Manual transaxle – Without depressing

the clutch pedal, press the engine

switch (1).

CVT – Without depressing the brake

pedal, press the engine switch (1).

82K253

57L31006

NOTE:

Manual transaxle

To save the battery, the illumination will be

automatically turned off when both of the

following conditions are simultaneously

met (battery saver function):

• The headlights and position lights are

turned off.

• A period of 15 minutes has elapsed after

opening the driver’s door.

LOCK

(OFF)

ACC

(Audio equipment)

(1)

57L31033

82K254

Every time you press the engine switch,

the ignition mode changes as follows.

3-7

58MS0-14E

Braking: 6

OPERATING YOUR VEHICLE

NOTE:

EXAMPLE

CVT – If the gearshift lever is in any posi-

• If you still cannot select the ignition

modes, there may be some problem with

the keyless push start system. Contact

an authorized SUZUKI dealer for an

inspection of the system.

tion other than “P”, or if the knob button is

pushed when the gearshift lever is in “P”

position the ignition mode cannot be

returned to “LOCK” (OFF).

(1)

• The immobilizer/keyless push start sys-

tem warning light will light for about 5

seconds while the “PUSH” indicator light

is blinking. Refer to “Warning and Indica-

tor Lights” in the “BEFORE DRIVING”

section for details.

• You may customize the system to cause

the interior buzzer to sound once for the

“remote controller out of sensing range”

warning. To incorporate this customiza-

tion, please contact an authorized

SUZUKI dealer.

• If the battery of the remote controller is

about to become completely discharged,

the keyless push start system remote

controller battery consumption warning

light in the instrument cluster will come

on for a few seconds when you press the

engine switch to change the ignition

mode to “ON”. Refer to “Warning and

Indicator Lights” in the “BEFORE DRIV-

ING” section for details. For details on

replacing the battery, refer to the “Key-

less Push Start System Remote Control-

ler” in the “BEFORE DRIVING” section.

If the “PUSH” indicator light blinks and

the ignition modes cannot be selected

Your keyless push start system remote

controller may not be sensed as being

within the “interior workable area” (Refer to

the related explanation in this section). Try

again after making sure you have the

remote controller with you. If the ignition

modes still cannot be selected, the battery

of the remote controller may be dis-

charged. To be able to select an ignition

mode, you must then use the following

method:

(2)

58MST0302

1) Without depressing the clutch pedal,

push the engine switch (1).

2) Within about 10 seconds during which

the “PUSH” indicator light in the instru-

ment cluster is blinking, touch the

engine switch with the lock switch end

of the remote controller (2) for about 2

seconds.

3-8

58MS0-14E

Running-in: 6

Catalytic Converter: NO

OPERATING YOUR VEHICLE

NOTE:

“Remote Controller Outside” Warning

When the conditions described below are

met, the system gives a “remote controller

outside” warning by sounding the interior

and exterior buzzers and blinking the

immobilizer/keyless push start system

warning light.

Interior Workable Area for Engine

Starting, Ignition Mode Selection

and “Remote Controller Outside”

Warning

• If the warning is given, locate the remote

controller as soon as possible.

• Any attempt to start the engine will fail

while the warning is active. Blinking of

the immobilizer/keyless push start sys-

tem warning light in the instrument clus-

ter will indicate this condition. Refer to

“Warning and Indicator Lights” in the

“BEFORE DRIVING” section for details.

• Blinking of the immobilizer/keyless push

start system warning light should stop

shortly after the remote controller is

brought back inside the vehicle. If they

do not stop blinking, change the ignition

mode to “LOCK” (OFF) by pressing the

engine switch and then perform the

engine starting operation.

• The remote controller is not inside the

vehicle when any of the doors is opened

when the engine is running or when the

engine switch is pressed to change the

ignition mode to “ACC” or “ON” and then

all doors are closed.

• The remote controller is not inside the

vehicle when you attempt to start the

engine after changing the ignition mode

to “ACC” or “ON” by pressing the engine

switch.

(1)

• Always keep the remote controller with

you as the driver.

68LM302

(1) Interior workable area

The “interior workable area” for these func-

tions is defined as all the interior spaces

except for the space above the instrument

panel.

(1)

68LM308

(1) Immobilizer/keyless push start sys-

tem warning light (blinking)

3-9

58MS0-14E

OPERATING YOUR VEHICLE -> Keyless Push Start System for Your Suzuki Swift 4 Door Second Generation (2010-2015)

Related Topics

Popular Owner Manuals

Latest Owner Manuals