INTERIOR FEATURES -> Touch-screen audio system for Your Toyota Aurion 4 Door Second Generation (2013-2017)

INTERIOR FEATURES  
Touch-screen audio system  
Touch-screen audio system  
HINT: For vehicles with Navigation system refer to the separate owners manual.  
By touching the screen with your finger, you can control the audio system and hands-free  
system, etc.  
QUICK REFERENCE  
Button  
Function  
AUDIO  
Audio system, refer to page 169  
Hands-free system, refer to page 204  
Setup menu, refer to page 164  
Vehicle information, refer to page 167  
SETUP  
CAR  
INFORMATION  
To avoid damaging the touch screen  
•
Touch the screen lightly with your finger. If there is no response, remove your finger  
from the screen and try again.  
•
Remove any dirt on the screen by wiping with a soft cloth. Do not use detergent.  
When using the touch screen  
•
If the screen is cold, the display may be dark, or the system may seem to be  
operating slightly slower than normal.  
•
The screen may seem dark and hard to see when viewed through sunglasses.  
Change your angle of viewing, adjust the display on the DISPLAY SETTINGS  
screen, refer to page 166, or remove your sunglasses.  
163  
INTERIOR FEATURES  
Touch-screen audio system  
SETUP MENU  
You can change the Touch-screen audio system to your desired setting.  
Press  
to display the SETUP screen.  
Touch the desired screen button to proceed to thollowing screens.  
Switch  
GENERAL  
DISPLAY  
Reference  
Refer to page 165  
Refer to page 166  
Refer to page 227  
Refer to page 218  
Refer to page 167  
BLUETOOTH  
TELEPHONE  
VEHICLE*  
Bluetooth® is a registered trademark of Bluetooth SIG, Inc.  
*Displayed only when the ignition switch is in the ON position (vehicles with standard  
type ignition switch) or the ENGINE START STOP switch is in the IGNITION ON position  
(vehicles with smart entry and start system).  
164  
INTERIOR FEATURES  
Touch-screen audio system  
General settings  
This screen is used for various settings.  
1. Press  
.
a
b
c
d
2. Touch GENERAL on the SETUP screen.  
a. Touch BEEP to set ON / OFF.  
b. Touch DISPLAY CAPTURED  
IMAGE to set ON / OFF.  
ON or OFF can be selected to  
display captured image / iPod®  
cover art in the screen.  
STNDA00001Ea  
c. Touch ANIMATION to set ON / OFF.  
The animation effect for audio  
source selection screen can be set  
to ON or OFF.  
d. Personal data can be deleted, refer  
below.  
3. When you complete settings, touch OK.  
Delete personal data−  
1. Touch DELETE PERSONAL DATA on  
the GENERAL SETTINGS screen.  
2. Touch DELETE.  
Check carefully beforehand, as data  
cannot be retrieved once deleted.  
3. A confirmation screen will be  
displayed. Touch Y.  
The following persoal data can be deleted  
or returned to their default settings:  
•
•
•
•
•
•
•
Phonebook data  
Call history data  
Speed dial data  
Bluetooth® devices data  
Phone sound settings  
Detailed Bluetooth® settings  
Sound settings  
165  
INTERIOR FEATURES  
Touch-screen audio system  
Display settings  
1. Press SETUP.  
2. Touch DISPLAY on the SETUP screen.  
a. Turn off screen.  
The screen is turned off.  
To turn it on, press any button such  
as AUDIO or SETUP.  
a
b
b. Changes to day mode, refer below.  
Displays only when the headlights  
are set to ON or AUTO.  
c
d
STNDA00109Ea  
c. Adjust screen contrast /  
brightness, refer below.  
d. Adjust screen contrast / brightness of the rear view monitor cmera, refer below.  
Changing between day mode and night mode−  
When the headlights are turned on, the screen dims.  
However, the screen can be switched to day mode by touching DAY MODE.  
The screen will stay in day mode when the headlights are turned on until DAY MODE is  
touched again.  
Adjusting the screen contrast / brightness−  
1. Touch GENERAL or CAMERA on the  
DISPLAY SETTINGS screen.  
2. Adjust the display as desired using  
[+] or [−].  
Select CONTRAST or BRIGHTNESS  
using the [<<] or [>>
[–]  
[+]  
CONTRAST  
Weaker  
Darker  
Stronger  
Brighter  
BRIGHTNESS  
3. Touch OK.  
166  
INTERIOR FEATURES  
Touch-screen audio system  
Vehicle settings  
1. Press SETUP.  
2. Touch VEHICLE* on the SETUP  
screen.  
Various settings can be changed.  
For details refer to “Customisable  
features” on page 333.  
3. When you complete the settings,  
touch OK.  
*Displayed only when the ignition switch is in the ON position (vehicles with standard  
type ignition switch) or the ENGINE START STOP switch is in the IGNITION ON position  
(vehicles with smart entry and start system).  
VEHICLE INFORMATION  
This screen can be used to display the fuel consumption.  
Press CAR to display the TRIP INFORMATION or PARECORD screen.  
167  
INTERIOR FEATURES  
Touch-screen audio system  
Fuel consumption  
Trip information−  
If the TRIP INFORMATION screen does  
not appear, touch TRIP INFORMATION.  
1. Average vehicle speed.  
2. Elapsed time.  
3. Cruising range.  
4. Previous fuel consumption per minute.  
5. Current fuel consumption.  
6. Reset the trip information data.  
7. PAST RECORD screen appears.  
NOTE: These images are examples only, and may vary slightly from actual conditions.  
Past record−  
If the PAST RECORD screen does not  
appear, touch PAST RECORD.  
1. Previous fuel economy record.  
2. Current fuel economy.  
3. Best recorded fuel economy.  
4. Update the Past record data.  
5. Reset the Past record data.  
6. TRIP INFORMATION screen appears.  
NOTE: These images are examples only, and may vary slightly from actual conditions.  
INFORMATION  
Resetting the data  
Selecting CLEAR on the TRIP INFORMATION screen will reset the consumption data.  
Selecting CLEAR on the PAST RECORD screen will reset the past record data.  
Updating the past record data  
Selecting UPDATE on the PAST RECORD screen will update the past record data.  
Also, the average fuel consumption displayed in the multi-information display will be  
reset at the same time.  
168  
INTERIOR FEATURES  
Touch-screen audio system  
AUDIO SYSTEM  
Press AUDIO to display the audio control screen.  
Title  
Page  
Using the radio  
Refer to page 172  
Refer to page 174  
Refer to page 174  
Refer to page 182  
Refer to page 187  
Refer to page 193  
Refer to page 194  
Refer to page 201  
Refer to page 202  
Using the CD player  
Playing an audio CD and MP3/WMA discs  
Listening to an iPod  
Listening to a USB memory  
Using the AUX port  
Listening to Bluetooth® audio  
Optimal use of the audio system  
Using the steering wheel audio switches  
169  
INTERIOR FEATURES  
Touch-screen audio system  
Switching the audio source  
1. Touch SOURCE or press AUDIO to  
display the audio source selection  
screen.  
2. Touch the desired audio source.  
: To scroll the screen.  
: Change to the list style screen  
as shown below.  
List style screen.  
170  
INTERIOR FEATURES  
Touch-screen audio system  
List screen operation  
When a list is displayed, use the  
appropriate button to scroll through the list.  
: To scroll to the next or previous  
page.  
: If  
appears to the right of titles, the  
complete titles are too long for the  
display.  
Touch this button to scroll to the title.  
Turn TUNE / SCROLL to move the cursor  
box to select a desired item from the list,  
and press TUNE / SCROLL to play it. The  
track that is being played is highlighted.  
INFORMATION  
Using mobile phones  
Interference may be heard through the audio systems speakers if a mobile phone is  
being used inside or close to the vehicle while the audio system is operating.  
CAUTION  
Laser product  
This product is a class 1 laser prouct.  
•
•
A laser beam leak may est in hazardous radiation exposure.  
Do not open the cover of the player or attempt to repair the unit yourself.  
Refer servicing to alified personnel.  
NOTICE  
To prevent battery discharge  
Do not leave the audio system on longer than necessary when the engine is off.  
To avoid damaging the audio system  
Take care not to spill drinks or other fluids on the audio system.  
171  
INTERIOR FEATURES  
Touch-screen audio system  
USING THE RADIO  
Touch AM or FM on the audio source selection screen.  
Power  
Volume  
Adjusting  
the frequency  
Selecting a frequency  
Muting the sound  
Dplaying the source selection  
or audio control screen  
CTY33AV192  
Audio control screen  
Pressing AUDIO displays the audio control  
screen from any screens of the slected  
source.  
1. Audio source selection creen  
appears.  
2. Scanning for receivable station.  
3. Setting the sound, refer to page 201.  
4. Preset stations.  
Selecting a station  
Seek tuning−  
Press [b] or [d] on SEEK / TRACK.  
Manual tuning−  
Turn TUNE / SCROLL.  
Preset stations−  
Touch desired preset stations [1 to 12].  
Change the page by using  
or  
.
172  
INTERIOR FEATURES  
Touch-screen audio system  
Setting station presets  
1. Search for desired stations by turning TUNE / SCROLL or pressing [b] or [d] on  
SEEK / TRACK.  
2. Touch and hold one of the preset stations [1 to 12] until you hear a beep.  
Scanning radio stations  
Scanning the preset radio stations−  
1. Touch SCAN on the screen until P.SCAN appears.  
Preset stations will be played for a few seconds each.  
2. Touch SCAN once again when the desired station is reached.  
Scanning all radio stations within range−  
1. Touch SCAN on the screen.  
SCAN appears on the screen and all stations within range will be played for a few  
seconds each.  
2. Touch SCAN once again when the desired station is reached.  
INFORMATION  
Reception sensitivity  
•
Maintaining perfect radio reception at all times is difficult due to the continually  
changing position of the antenna, differnces in signal strength and surrounding  
objects, such as trains, transmittrs, etc.  
•
The radio antenna is mounted inside the rear window. To maintain clear radio  
reception, do not attach metallic window tinting or other metallic objects to the  
antenna wire mounted nside the rear window.  
173  
INTERIOR FEATURES  
Touch-screen audio system  
USING THE CD PLAYER  
Power  
Volume  
Selecting a  
track and file  
Ejecting  
a disc  
Disc slot  
Selecting a track and fie / fast-forwarding  
and reversing  
Playback / pause  
Displayinthe source selection  
or audio control screen  
Loading a disc  
Insert a disc into the disc slot with the label facing up.  
Ejecting a disc  
Press  
and remove the disc.  
PLAYING AN AUDIO CAND MP3 / WMA DISCS  
Insert a disc or touch Con the audio source selection screen with a disc inserted.  
Audio control screen  
Pressing AUDIO displays the audio control screen from any screens of the selected source.  
Audio CD  
1. Audio source selection screen  
appears.  
2. Displaying the track / file list.  
3. Pause.  
(Touch  
to play.)  
4. Repeat play.  
5. Random playback.  
6. Setting the sound, refer to page 201.  
174  
INTERIOR FEATURES  
Touch-screen audio system  
MP3 / WMA disc  
1. Audio source selection screen  
appears.  
2. Displaying the track / file list.  
3. Pause.  
(Touch  
to play.)  
4. Repeat play.  
5. Random playback.  
6. Displaying the folder list.  
7. Setting the sound, refer to page 201.  
Selecting, fast-forwarding and reversing tracks (Audio CD)  
Selecting a track−  
Press [b] or [d] on SEEK / TRACK or turn TUNE / SCROLL to sect the desired track  
number.  
To fast-forward or reverse, press and hold [b] or [d] on SEEK / TRACK.  
Selecting a track from the track list−  
1. Touch TRACKS on the audio control  
screen.  
2. Touch the desired track number.  
Selecting, fast-forwarding and reversing files (MP3/WMA disc)  
Selecting a file−  
Press [b] or [d] on SEEK / TRACK or turn TUNE / SCROLL to select the desired file  
number.  
To fast-forward or reverse, press and hold [b] or [d] on SEEK / TRACK until you hear a  
beep.  
Selecting a file from the file list−  
1. Touch FILES on the audio control  
screen.  
2. Touch the desired file number.  
175  
INTERIOR FEATURES  
Touch-screen audio system  
Selecting a folder (MP3/WMA disc)  
1. Touch FOLDERS on the audio control  
screen.  
2. Touch the desired folder number.  
3. Touch the desired file number.  
Random playback  
Each time  
is touched, the mode changes in the following order:  
Audio CD−  
.
MP3/WMA disc−  
.
Repeat play  
Each time  
is touched, the mode changes in the following order:  
Audio CD−  
.
MP3/WMA disc−  
.
176  
INTERIOR FEATURES  
Touch-screen audio system  
INFORMATION  
Displaying the title and artist name  
If a CD-TEXT disc is inserted, the title of the disc and track will be displayed.  
Error messages  
Refer to the following table and take the appropriate measures. If the problem is not  
rectified, take the vehicle to your Toyota dealer.  
Message  
Cause  
Correction procedures  
Clean the disc.  
•
•
•
The disc is dirty or  
damaged.  
The disc is inserted upside  
down.  
Insert the disc correctly.  
CHECK DISC  
The disc is not playable  
with the player.  
Confirm e disc is playable  
with the player.  
There is a malfunction within  
the system.  
DISC ERROR  
Eject the disc.  
Eject the disc.  
NO MUSIC  
FILES FOUND  
This indicates that no playabl
data is included in the disc
Discs that can be used  
Discs with the marks shown below can be used.  
Playback may not be possible depending on the recording format or disc features, or  
due to scratches, dirt or deterioration.  
CDs with copy-protecion features may not play correctly.  
CD player protection feature  
To protect the internal components, playback is automatically stopped when a problem  
is detected.  
If a disc is left inside the CD player or in the ejected position for extended periods  
The disc may be damaged and may not play properly.  
Lens cleaners  
Do not use lens cleaners. Doing so may damage the CD player.  
177  
INTERIOR FEATURES  
Touch-screen audio system  
INFORMATION  
MP3 and WMA files  
MP3 (MPEG Audio LAYER3) is a standard audio compression format.  
Files can be compressed to approximately 1/10 of their original size by using MP3  
compression.  
WMA (Windows Media Audio) is a Microsoft audio compression format.  
This format compresses audio data to a size smaller than that of the MP3 format.  
There is a limit to the MP3 and WMA file standards that can be used and to the  
media / formats on which the files are recorded.  
MP3 file compatibility−  
•
Compatible standards  
MP3 (MPEG1 LAYER3, MPEG2 LSF LAYER3).  
•
Compatible sampling frequencies  
MPEG1 LAYER3: 32, 44.1, 48 (kHz)  
MPEG2 LSF LAYER3: 16, 22.05, 24 (kHz).  
•
•
Compatible bit rates  
MPEG1 LAYER3: 32—320 (kbps)  
MPEG2 LSF LAYER3: 8—160 (kbps).  
Compatible channel modes: stereo, joinstereo, dual channel and monaural.  
WMA file compatibility−  
•
•
•
Compatible standards  
WMA Ver. 7, 8, 9.  
Compatible sampling frequencies  
32, 44.1, 48 (kHz).  
Compatible bit rates (only compatible with 3-channel playback)  
Ver. 7, 8: CBR 48—192 (kbps)  
Ver. 9: CBR 48—320 (kbps).  
Compatible media−  
Media that can be used for MP3 and WMA playback are CD-Rs and CDRWs.  
Playback in some instances may not be possible if the CD-R or CD-RW is not finalised.  
Playback may not be possible or the audio may jump if the disc is scratched or marked  
with fingerprints.  
178  
INTERIOR FEATURES  
Touch-screen audio system  
INFORMATION  
Compatible disc formats−  
The following disc formats can be used.  
•
•
Disc formats: CD-ROM Mode 1 and Mode 2  
CD-ROM XA Mode 2, Form 1 and Form 2.  
File formats: ISO9660 Level 1, Level 2, (Romeo, Joliet)  
UDF (2.01 or lower).  
MP3 and WMA files written in any format other than those listed above may not  
play correctly, and their file names and folder names may not be displayed correctly.  
Items related to standards and limitations are as follows:  
•
•
•
•
Maximum directory hierarchy: 8 levels (including the root)  
Maximum length of folder names / file names: 32 characters  
Maximum number of folders: 192 (including the root)  
Maximum number of files per disc: 255  
File names−  
The only files that can be recognised as MP3 / WMA and played are those with the  
extension .mp3 or .wma.  
Discs containing multi-session recordings−  
As the audio system is compatible witmulti-sessions, it is possible to play discs that  
contain MP3 and WMA files. However, only the first session can be played.  
ID3 and WMA tags−  
ID3 tags can be added to MP3 files, making it possible to record the track title, artist  
name, etc.  
The system is compatible with ID3 Ver. 1.0, 1.1, and Ver. 2.2, 2.3 ID3 tags.  
(The number of characters is based on ID3 Ver. 1.0 and 1.1.)  
WMA tags can be added to WMA files, making it possible to record the track title and  
artist name in the same way as with ID3 tags.  
MP3 and WMA playback−  
When a disc containing MP3 or WMA files is inserted, all files on the disc are first  
checked. Once the file check is finished, the first MP3 or WMA file is played. To make  
the file check finish more quickly, we recommend you do not write in any files other than  
MP3 or WMA files or create any unnecessary folders.  
Discs that contain a mixture of music data and MP3 or WMA format data cannot be  
played.  
179  
INTERIOR FEATURES  
Touch-screen audio system  
INFORMATION  
Extensions−  
If the file extensions .mp3 and .wma are used for files other than MP3 and WMA files,  
they will be mistakenly recognised and played as MP3 and WMA files. This may result in  
large amounts of interference and damage to the speakers.  
Playback−  
•
•
•
To play MP3 files with steady sound quality, we recommend a fixed bit rate of 128  
kbps and a sampling frequency of 44.1 kHz.  
CD-R or CD-RW playback may not be possible in some instances, depending on the  
characteristics of the disc.  
There is a wide variety of freeware and other encoding software for MP3 and WMA  
files on the market, and depending on the status of the encoding and the file  
format, poor sound quality or noise at the start of playback may esult. In some  
cases, playback may not be possible at all.  
•
•
When files other than MP3 or WMA files are recorded on a disc, it may take more  
time to recognise the disc and in some cases, playback may not be possible at all.  
Microsoft, Windows, and Windows Media are the registered trademarks of  
Microsoft Corporation in the U.S. and other countries.  
180  
INTERIOR FEATURES  
Touch-screen audio system  
NOTICE  
Discs and adapters that cannot be used  
Do not use the following types of discs  
or 8 cm disc adapters or Dual Discs.  
Doing so may damage the player  
and / or the insert / eject function.  
•
Discs that have a diameter that is  
not 12 cm.  
•
Low-quality and deformed discs.  
•
Discs with a transparent or  
translucent recording area.  
•
Discs that have had tape, stickers or  
CD-R labels attached to them, or  
that have had the label peeled off.  
181  
INTERIOR FEATURES  
Touch-screen audio system  
NOTICE  
Player precautions  
Failure to follow the precautions below may result in damage to the discs or the player  
itself.  
•
•
•
•
Do not insert anything other than discs into the disc slot.  
Do not apply oil to the player.  
Store discs away from direct sunlight.  
Never try to disassemble any part of the player.  
LISTENING TO AN iPod®  
Connecting an iPod® enables you to enjoy music from the vehicle speakers.  
Touch iPod® on the audio source selection screen.  
Power  
Volume  
Selecting a song  
Selecting a song / fast-forwarding  
and reversing  
Playback / pause  
Displaying the source selection  
or audio control screen  
182  
INTERIOR FEATURES  
Touch-screen audio system  
Audio control screen  
Pressing AUDIO displays the audio control  
screen from any screens of the selected  
source.  
1. Audio source selection screen  
appears.  
2. Selecting the play mode.  
3. Displaying the song list.  
4. Pause.  
(Touch  
to playback.)  
5. Repeat play.  
6. Shuffle play.  
7. Setting the sound, refer to page 201.  
Connecting an iPod®  
1. Lift the lid.  
2. Open the cover and onnect an iPod®  
using an iPod® cable.  
Turn on the power of the iPod® if it is  
not turned on.  
183  
INTERIOR FEATURES  
Touch-screen audio system  
Playing an iPod®  
Play / Pause−  
Touch  
or  
to Play / Pause.  
Selecting a play mode−  
1. Touch BROWSE on the audio control  
screen.  
2. Select the desired play mode by  
touching the PLAYLISTS, ARTISTS,  
ALBUMS, SONGS, PODCASTS,  
AUDIO BOOKS, GENRES or  
COMPOSERS tabs.  
Selecting, fast-forwarding and reversing songs  
Selecting one song at a time−  
Press [b] or [d] on SEEK / TRACK or turn TUNE / SCROLL to select the desired song.  
To fast-forward or reverse, press and hold [b] or [d] oSEEK / TRACK until you hear a  
beep.  
Selecting a song from the list−  
1. Touch SONGS on the audio control  
screen.  
2. Touch the desired song.  
Shuffle play  
Each time  
is touched, the mode changes in the following order:  
.
When a large number of songs is stored in an iPod®, shuffle selection may take time.  
Repeat play  
Each time  
is touched, the mode changes in the following order:  
.
184  
INTERIOR FEATURES  
Touch-screen audio system  
INFORMATION  
About iPod®  
•
“Made for iPod®” and “Made for  
iPhone®” means that an electronic  
accessory has been designed to  
connect specifically to iPod®, or  
iPhone®, respectively, and has been  
certified by the developer to meet  
Apple performance standards.  
•
•
Apple is not responsible for the operation of this device or its compliance with  
safety and regulatory standards. Please note that the use of this accessory with  
iPod® or iPhone® may affect wireless performance.  
iPhone®, iPod®, iPod® classic, iPod® nano, iPod® shuffle, and iPod® touch are  
trademarks of Apple Inc., registered in the U.S. and other countries.  
iPod® cover art  
•
•
•
Depending on the iPod® and songs in the iPod®, iPod® cover art may be displayed.  
This function can be changed to ON or OFF, refto page 165.  
It may take time to display iPod® cover art, and the iPod® may not be operated while  
the cover art display is in process.  
•
Only iPod® cover art that is saved in JPEG format can be displayed.  
iPod® functions  
•
When an iPod® is connected and the audio source is changed to iPod® mode, the  
iPod® will resume play om the same point in which it was last used.  
•
Depending on the iPd® that is connected to the system, certain functions may  
not be available. If function is unavailable due to a malfunction (as opposed to a  
system specificaion), disconnecting the device and reconnecting it once again may  
resolve the problem.  
•
•
•
While connected to the system, the iPod® cannot be operated with its own controls.  
It is necessary to use the controls of the vehicle’s audio system instead.  
When the battery level of an iPod® is very low, the iPod may not operate. If so,  
charge the iPod® before use.  
For supported models refer to “Compatible models” on page 186.  
iPod® problems  
To resolve most problems encountered when using your iPod®, disconnect your iPod®  
from the vehicle iPod® connection and reset it.  
For instructions on how to reset your iPod®, refer to your iPod® Owner’s Manual.  
185  
INTERIOR FEATURES  
Touch-screen audio system  
INFORMATION  
Error messages  
CONNECTION ERROR: This indicates a problem in the iPod® or its connection.  
THERE ARE NO SONGS AVAILABLE FOR PLAYBACK:  
This indicates there is no music data in the iPod®.  
NO ITEMS AVAILABLE: This indicates that some available songs are not found in a  
selected playlist.  
Compatible models  
The following iPod®, iPod nano®, iPod classic®, iPod touch® and iPhone® devices can  
be used with this system.  
Made for  
• iPod touch (1st, 2nd, 3rd and 4th generation)  
• iPod classic  
• iPod with video  
• iPod nano (1st, 2nd, 3rd, 4th, 5th and 6th generation)  
• iPhone (iPhone, 3G, 3GS and 4)  
Depending on differences between models or softwre version etc., some models listed  
above might be incompatible with this system.  
iPod® 4th generation and earlier models are not compatible with this system.  
iPod® mini, iPod® shuffle and iPod® pho are not compatible with this system.  
CAUTION  
Do not connect an iPod® or operate the controls while driving.  
NOTICE  
If the auxiliary box lid cannot be fully closed  
Depending on the size and shape of the iPod® that is connected to the system, the  
auxiliary box lid may not close fully. In this case, do not forcibly close the lid as this may  
damage the iPod® or the terminal, etc.  
To prevent damage to the iPod or its terminal  
•
•
•
Do not leave the iPod® in the vehicle. The temperature inside the vehicle may  
become high, resulting in damage to the iPod®.  
Do not push down on or apply unnecessary pressure to the iPod® while it is  
connected.  
Do not insert foreign objects into the port.  
186  
INTERIOR FEATURES  
Touch-screen audio system  
LISTENING TO A USB MEMORY  
Connecting a USB memory enables you to enjoy music from the vehicle speakers.  
Touch USB on the audio source selection screen.  
Power  
Volume  
Selecting a file  
Selecting a file / fast-forwarding  
and reversing  
Playback / pause  
Displaying the source selection  
or audio control screen  
Audio control screen  
Pressing AUDIO displays the audio control screen from any screens of the selected source.  
1. Audio source selection screen  
appears.  
2. Displaying the folder list.  
3. Displaying the file list.  
4. Pause.  
(Touch  
to playback.)  
5. Repeat play.  
6. Random playback.  
7. Setting the sound, refer to page 201.  
187  
INTERIOR FEATURES  
Touch-screen audio system  
Connecting a USB memory  
1. Lift the lid.  
2. Open the cover and connect the USB  
memory.  
Turn on the power of the USB memory  
if it is not turned on.  
Selecting, fast-forwarding and reversing files  
Selecting one file at time−  
Press [b] or [d] on SEEK / TRACK or turn TUNE / SCROLL to select the desired file.  
To fast-forward or reverse, prss and hold [b] or [d] on SEEK / TRACK until you hear a  
beep.  
Selecting a file from the list−  
1. Touch FILES on the audio control  
screen.  
2. Touch the desired file number.  
188  
INTERIOR FEATURES  
Touch-screen audio system  
Selecting a folder  
1. Touch FOLDERS on the audio control  
screen.  
2. Touch the desired folder number.  
3. Touch the desired file number.  
Random playback  
Each time  
is touched, the mode changes in the following order:  
.
Repeat play  
Each time  
is touched, the mode changes in the following order:  
.
189  
INTERIOR FEATURES  
Touch-screen audio system  
INFORMATION  
USB memory functions  
•
Depending on the USB memory that is connected to the system, the device itself  
may not be operable and certain functions may not be available. If the device  
is inoperable or a function is unavailable due to a malfunction (as opposed to a  
system specification), disconnecting the device and reconnecting it once again may  
resolve the problem.  
•
If the USB memory still does not begin operation after being disconnected and  
reconnected, format the memory.  
Error messages  
CONNECTION ERROR: This indicates a problem in the USB memory or its connection.  
THERE ARE NO FILES AVAILABLE FOR PLAYBACK:  
This indicates that no MP3/WMA files are included in the USB  
memory.  
USB memory  
Compatible devices−  
USB memory that can be used for MP3 and WMA playback.  
Compatible device formats−  
The following device formats can be used:  
•
•
•
USB communication formats: USB2.0 FS (12 Mbps)  
File formats: FAT16/32 (Windows)  
Correspondence class: Mass storage class  
MP3 and WMA files written in any format other than those listed above may not  
play correctly, and thefile names and folder names may not be displayed correctly  
Items related to standads and limitations are as follows:  
•
•
•
•
Maximum directory hierarchy: 8 levels  
Maximum number of folders in a device: 3000 (including the root)  
Maximum number of files in a device: 9999  
Maximum number of files per folder: 255  
190  
INTERIOR FEATURES  
Touch-screen audio system  
INFORMATION  
MP3 and WMA files−  
MP3 (MPEG Audio LAYER 3) is a standard audio compression format.  
Files can be compressed to approximately 1/10 of their original size using MP3  
compression.  
WMA (Windows Media Audio) is a Microsoft audio compression format.  
This format compresses audio data to a size smaller than that of the MP3 format.  
There is a limit to the MP3 and WMA file standards that can be used and to the  
media / formats on which the files are recorded.  
MP3 file compatibility−  
•
Compatible standards  
MP3 (MPEG1 AUDIO LAYERII, III, MPEG2 AUDIO LAYERII, I, MPEG2.5).  
•
Compatible sampling frequencies  
MPEG1 AUDIO LAYERII, III: 32, 44.1, 48 (kHz)  
MPEG2 AUDIO LAYERII, III: 16, 22.05, 24 (kHz).  
•
•
Compatible bit rates (compatible with VBR)  
MPEG1 AUDIO LAYERII, III: 32-320 (kbps)  
MPEG2 AUDIO LAYERII, III: 8-160 (kbps).  
Compatible channel modes: stereo, int stereo, dual channel and monaural.  
WMA file compatibility−  
•
•
•
Compatible standards  
WMA Ver. 7, 8, 9.  
Compatible sampling frequencies  
HIGH PROFILE 32, 4.1, 48 (kHz).  
Compatible bt rtes  
HIGH PROFILE 48-320 (kbps, VBR).  
File names−  
The only files that can be recognised as MP3/WMA and played are those with the  
extension .mp3 or .wma.  
ID3 and WMA tags−  
ID3 tags can be added to MP3 files, making it possible to record the track title, artist  
name, etc.  
The system is compatible with ID3 Ver. 1.0, 1.1, and Ver. 2.2, 2.3, 2.4 ID3 tags.  
(The number of characters is based on ID3 Ver. 1.0 and 1.1.)  
WMA tags can be added to WMA files, making it possible to record the track title and  
artist name in the same way as with ID3 tags.  
191  
INTERIOR FEATURES  
Touch-screen audio system  
INFORMATION  
MP3 and WMA playback−  
•
When a device containing MP3 or WMA files is connected, all files in the USB  
memory are checked. Once the file check is finished, the first MP3 or WMA file is  
played. To make the file check finish more quickly, we recommend that you do not  
include any files other than MP3 or WMA files or create any unnecessary folders.  
•
When the USB memory is connected and the audio source is changed to USB  
memory mode, the USB memory will start playing the first file in the first folder.  
If the same device is removed and reinserted (and the contents have not been  
changed), the USB memory will resume play from the same point in which it was  
last used.  
Extensions−  
If the file extensions .mp3 and .wma are used for files other than MP3 and WMA files,  
they will be skipped (not played).  
Playback−  
•
To play MP3 files with steady sound quality, we recommend a fixed bit rate of at  
least 128 kbps and a sampling frequency of 44.1 kH
•
There is a wide variety of freeware and other ending software for MP3 and WMA  
files on the market, and depending on the status of the encoding and the file  
format, poor sound quality or noise at the strt of playback may result. In some  
cases, playback may not be possible t all.  
•
Microsoft, Windows, and Windows Media are registered trademarks of Microsoft  
Corporation in the U.S.A. and other countries.  
CAUTION  
Do not connect a USB memory or operate the controls while driving.  
NOTICE  
If the auxiliary box lid cannot be fully closed  
Depending on the size and shape of the USB memory that is connected to the system,  
the auxiliary box lid may not close fully. In this case, do not forcibly close the lid as this  
may damage the USB memory or the terminal, etc.  
To prevent damage to the USB memory or its terminal  
•
•
•
Do not leave the USB memory in the vehicle. The temperature inside the vehicle  
may become high, resulting in damage to the USB memory.  
Do not push down on or apply unnecessary pressure to the USB memory while it is  
connected.  
Do not insert foreign objects into the port.  
192  
INTERIOR FEATURES  
Touch-screen audio system  
USING THE AUX PORT  
This port can be used to connect a portable  
audio device and listen to it through the  
vehicle’s speakers.  
1. Lift the lid.  
2. Open the cover and connect the  
portable audio device.  
3. Touch AUX on the audio source  
selection screen.  
INFORMATION  
Operating portable audio deves connected to the audio system  
The volume can be adjusted using the vehicle’s audio controls. All other adjustments  
must be made on the portable audio device itself.  
When using a portale audio device connected to the power outlet  
Noise may occur during playback. Use the power source of the portable audio device.  
193  
INTERIOR FEATURES  
Touch-screen audio system  
LISTENING TO BLUETOOTH® AUDIO  
The Bluetooth® audio system enables users to enjoy music played on a portable player  
from the vehicle speaker via wireless communication. This audio system supports  
Bluetooth®, a wireless data system capable of playing portable audio music without  
cables. If your portable player does not support Bluetooth®, the Bluetooth® audio system  
will not function.  
Touch BT on the audio source selection screen.  
Power  
Volume  
Selecting a track  
Selecting a track / fast-forwarding  
and reversing  
Playback / pause  
Displaying the source selection  
or audio control screen  
Audio control screen  
Pressing AUDIO displays the audio control  
screen from any screens of the selected  
source.  
1. Audio source selection screen appears.  
2. Displaying the album list.  
3. Displaying the track list.  
4. Connecting a Bluetooth® audio player.  
5. Playback.  
6. Pause.  
7. Repeat play.  
8. Random playback.  
9. Setting the sound, refer to page 201.  
194  
INTERIOR FEATURES  
Touch-screen audio system  
Status display  
You can check such indicators as signal  
strength and battery charge on the screen.  
1. Connection status.  
2. Battery charge.  
Indicators  
Conditions  
Connection status  
Battery charge  
Registering a Bluetooth® audio player  
To use the Bluetooth® audio system, you  
need to register your portable audio player  
into the system. Once registered, you can  
enjoy your music on the vehicle’s audio  
system.  
You can register up to 5 devics in the  
system.  
1. Touch CONNECT ohe audio control  
screen.  
2. Touch YES.  
195  
INTERIOR FEATURES  
Touch-screen audio system  
3. Input the passcode displayed on the  
screen into your portable audio player.  
For the operation of the portable audio  
player, see the manual that comes  
with your portable audio player.  
Passcodes are not required for SSP  
(Secure Simple Pairing) compatible  
Bluetooth® devices. Depending on the  
device, you may need to select YES  
to register, or NO to cancel on your  
Bluetooth® device.  
If you want to cancel it, select CANCEL.  
If a completion message is displayed, registration is complete.  
If an error message is displayed, follow the guidance on the scren to try again.  
Selecting the Bluetooth® audio player  
If multiple Bluetooth® devices are  
registered, follow the procedure below to  
select the Bluetooth® device to be used.  
You may only use one device at a time.  
1. Touch CONNECT on the audio control  
screen.  
2. Touch the device to coect.  
ADD NEW: Registeing a Bluetooth®  
device, refer to page 195.  
The selection indicator is displayed on  
left side of the selected device name.  
The Bluetooth® mark is displayed  
when you connect the device.  
196  
INTERIOR FEATURES  
Touch-screen audio system  
Connecting the Bluetooth® audio player  
There are two connection methods available.  
When the connection method is set to FROM VEHICLE−  
Vehicles with standard type ignition switch−  
When the portable audio player is on standby for the connection, it will be automatically  
connected whenever the ignition switch is in either ACC or ON position.  
Vehicles with a smart entry and start system−  
When the portable audio player is on standby for the connection, it will be automatically  
connected whenever the ENGINE START STOP switch is in either ACCESSORY or  
IGNITION ON mode.  
When the connection method is set to FROM AUDIO PLAYER−  
Operate the portable player and connect  
it to the Bluetooth® audio system.  
1. Touch CONNECT on the audio control  
screen.  
2. Touch the device to connect.  
A message is shown if connecion has  
been successful.  
If connection fails, a message will be  
displayed and connection will be  
re-attempted.  
Playing Bluetooth® audio  
Touch  
or  
to play / pause.  
197  
INTERIOR FEATURES  
Touch-screen audio system  
Some titles and controls may not be  
displayed depending on the type of  
portable audio player.  
Selecting a track  
Selecting a track−  
Press [b] or [d] on SEEK / TRACK or turn TUNE / SCROLL to select the desired track  
number.  
To fast-forward or rewind, press and hold [b] or [d] on SEEK / TRACK until you hear a  
beep.  
Selecting a track from the list−  
1. Touch TRACKS on the audio control  
screen.  
2. Touch the desired track.  
Selecting an album  
1. Touch BROWSE on the audio control  
screen.  
2. Touch the desired album.  
198  
INTERIOR FEATURES  
Touch-screen audio system  
3. Touch the desired track.  
Random playback  
Each time  
is touched, the mode changes in the following order:  
.
Repeat play  
Each time  
is touched, the mode changes in the following order:  
.
INFORMATION  
When using the Bluetooth® audio sstem  
In the following conditions, the sytem may not function.  
•
•
•
If the portable audio playes turned off.  
If the portable audio player is not connected.  
If the portable audplayer’s battery is low.  
There may be a dely if phone connection is carried out during Bluetooth® audio play.  
Depending on the type of portable audio player that is connected to the system,  
operation may differ slightly and certain functions may not be available.  
Bluetooth® antenna  
The antenna is built into the display. If the portable audio player is behind the seat or  
in the glove box or console box, or is touching or covered by metal objects, connection  
status may deteriorate.  
Battery charge / signal status  
This display may not correspond exactly with the portable audio player, and this system  
does not have a charging function.  
199  
INTERIOR FEATURES  
Touch-screen audio system  
INFORMATION  
About Bluetooth®  
Bluetooth is a registered trademark of  
Bluetooth SIG, Inc.  
The Bluetooth wordmark and logo are  
owned by Bluetooth SIG. and permission  
has been granted to use the trademark of  
the licensee FUJITSU TEN LIMITED.  
Other trademarks and trade names are  
owned by various different owners.  
Compatible models  
Portable audio players must correspond to the specifications.  
•
Bluetooth® specifications:  
Ver. 1.1, or higher (recommended: Ver. 2.1 + EDR ohigher)  
•
Profiles:  
–
A2DP (Advanced Audio Distribution Profil) Ver. 1.0, or higher (recommended:  
Ver. 1.2 or higher). This is a profile to tramit stereo audio or high quality  
sounds to the headphone  
–
AVRCP (Audio / Video Remote Cntrol Profile) Ver. 1.0 or higher (recommended:  
Ver. 1.4 or higher). This is a profile to remote control the A/V equipment  
However, please note that me functions may be limited depending on the type  
of portable audio player  
Reconnecting the portabaudio player  
Vehicles with standard ype ignition switch−  
If the portable audio player is disconnected due to a poor reception when the ignition  
switch is in the ACC or ON position, the system automatically reconnects the portable  
audio player when possible.  
Vehicles with a smart entry and start system−  
If the portable audio player is disconnected with a poor reception when the ENGINE  
START STOP switch is in ACCESSORY or IGNITION ON mode, the system automatically  
reconnects the portable audio player.  
If you have switched off the portable audio player yourself, follow the instructions below  
to reconnect.  
•
•
Select the portable audio player again.  
Enter the portable audio player.  
200  
INTERIOR FEATURES  
Touch-screen audio system  
INFORMATION  
When transferring ownership of the vehicle  
Initialise the system to prevent personal data from being improperly accessed, refer to  
page 165.  
CAUTION  
Do not use the portable audio player or connect the Bluetooth® system while driving.  
NOTICE  
When leaving the vehicle  
Do not leave your portable audio player in the vehicle. The inside of the vehicle may  
become hot, causing damage to the portable audio player.  
OPTIMAL USE OF THE AUDIO SYSTEM  
Touch  
to adjust the sound settings.  
SOUND tab  
1, 2, 3. Touch [−] or [+] to adjust the  
treble, mid or bass to a level  
between −5 to 5.  
4, 5.  
Touch FRONT or REAR to adjust the  
front / rear audio balance to a level  
between Front 7 and Rear 7.  
6, 7.  
Touch L or R to adjust the left / right  
audio balance to a level between L7  
and R7.  
201  
INTERIOR FEATURES  
Touch-screen audio system  
DSP tab  
1. Automatic sound leveliser (ASL)  
Adjust the ASL level in the order of  
HIGH, MID, LOW or OFF.  
INFORMATION  
The sound quality level is adjusted individually  
The treble, mid and bass levels can be adjusted for each audio mode separately.  
About Automatic Sound Leveliser (ASL)  
ASL automatically adjusts the volume and tone quality according to the vehicle speed.  
USING THE STEERING WHEEL AUDIO SWITCHES  
Some audio features can be controlled using the witches on the steering wheel.  
1. Increases / decreases volume.  
Without Paddle Shift  
2. Returns to the previous screen.  
3. Radio mode:  
Selects radio stations.  
CD mode:  
Selects tracks / files and folders  
(MP3/WMA).  
iPod® mode:  
Selects songs.  
USB memory mode:  
Selects files and folders.  
With Paddle Shift  
Bluetooth® audio mode:  
Selects tracks and albums.  
List screen:  
Moves cursor.  
4. Turns the power on, selects audio source.  
5. Radio mode:  
Displays the preset screen.  
Media mode:  
CTY33AV211a  
Displays the list screen  
List screen:  
Selects items.  
202  
INTERIOR FEATURES  
Touch-screen audio system  
Turning on the power  
Press MODE when the audio system is turned off.  
Changing the audio source  
Press MODE when the audio system is turned on. The audio source changes as follows  
each time MODE is pressed. If no discs are inserted in the player, or if the external device  
is not connected, that mode will be skipped.  
FM → CD player → iPod® / USB memory → Bluetooth® audio → AUX → AM.  
Adjusting the volume  
Press [+] to increase the volume and [−] to decrease the volume.  
Hold the button in that position to continue increasing or decreasing the volume.  
Silencing a sound  
Press and hold MODE.  
To cancel, press and hold MODE.  
Returning to the previous screen  
Press  
to display the previous screen.  
Displaying the preset screen (radio)  
1. Press MODE to select the radio mode.  
2. Press  
to display the preset screen.  
Selecting a radio station  
1. Press MODE to select the radio mode.  
2. Press [b] or [d] on  
to elect a radio station.  
To seek stations, press and hold [b] or [d] on  
until you hear a beep.  
The radio preset page can be changed by pressing [>] or [<] on  
(FM mode only).  
Selecting a track / fior song  
1. Press MODE to select the CD, Bluetooth® audio, iPod®, USB memory mode.  
2. Press [b] or [d] on to select the desired track / file or song.  
To return to the beginning of the track / file or song, press [d] on  
once quickly.  
Selecting a folder or album  
1. Press MODE to select the CD (only when MP3/WMA disc is in use), Bluetooth® audio,  
iPod® or USB memory mode.  
2. Press [�] or [ ] on  
to select the desired folder or album.  
Displaying the list screen  
1. Press MODE to select CD, Bluetooth® audio, iPod® or USB memory mode.  
2. Press to display the list screen.  
203  
INTERIOR FEATURES  
Touch-screen audio system  
Operating on the list screen  
1. Press [b] or [d] on  
2. Press to select an item.  
When the folder or album is selected, the SELECT FILE screen is displayed.  
to move the cursor up or down.  
CAUTION  
To reduce the risk of an accident  
Exercise care when operating the audio switches on the steering wheel.  
HANDS-FREE SYSTEM (FOR MOBILE PHONES)  
The hands-free system is a function that allows you to use your mobile phone without  
touching it.  
This system supports Bluetooth®. Bluetooth® is a wireless data systethat allows the  
mobile phone to wirelessly connect to the hands-free system and make / receive calls.  
Telephone switch  
1. Off hook switch  
With padde shift switches  
–
–
Sending.  
Receiving.  
2. On hook switch  
–
–
End call.  
Refuse call.  
3. Volume switch  
–
–
–
Increase the volume.  
Decrease the volume.  
Without paddle shift switches  
TELEPHONE scren display.  
4. Back switch  
–
Return to the previous screen.  
5. Cursor switch  
–
–
Selects lists.  
Selects tabs.  
6. Enter switch  
Select items.  
–
CTY33AV251a  
204  
INTERIOR FEATURES  
Touch-screen audio system  
Microphone  
You can use the microphone when talking  
on the phone.  
The person you are speaking to can be  
heard from the front speakers.  
To use the hands-free system, you must  
register your Bluetooth® phone in the  
system, refer to page 209.  
Status display  
You can check indicators such as signal  
strength and battery charge on the  
TELEPHONE screen.  
1. Connection status.  
2. Battery charge.  
3. Call area.  
4. Signal strength.  
Indicators  
Conditions  
Connection status  
Battery chage  
Call area  
Rm: Roaming area  
Signal strength  
205  
INTERIOR FEATURES  
Touch-screen audio system  
INFORMATION  
When using the hands-free system  
•
•
•
The audio system is muted when making a call.  
If both parties speak at the same time, it may be difficult to hear.  
If the received call volume is overly loud, an echo may be heard.  
If the Bluetooth® phone is too close to the system, quality of the sound may  
deteriorate and connecting condition may go down.  
•
In the following circumstances, it may be difficult to hear the other party.  
–
–
–
–
–
When driving on unpaved roads.  
When driving at high speeds.  
If a window is open.  
If the air conditioning is blowing directly on the microphone.  
There is an effect from the network of the mobile phone.  
Conditions under which the system will not operate  
•
•
•
•
•
•
•
•
If using a mobile phone that does not support Bluetooth®.  
If the mobile phone is turned off.  
If you are outside service range.  
If the mobile phone is not connected.  
If the mobile phone’s battery is low.  
When outgoing is controlled, due to heavy traffic on telephone lines, etc.  
When the mobile phone itself cannot be used.  
When transferring the phonebook data from the mobile phone.  
Bluetooth® antenna  
The antenna is built into he display. If the mobile phone is behind the seat or in the  
console box, or touching or covered by metal objects, connection status may deteriorate.  
Battery charge / Signal status  
•
•
•
This display may not correspond exactly with the mobile phone itself.  
This system does not have a charging function.  
The Bluetooth® phone battery will be depleted quickly when it is connected to  
Bluetooth®.  
•
•
When the mobile phone is not connected, NO CONNECT is displayed.  
When you are out of service area or in a place inaccessible by radio waves,  
NO SERVICE is displayed.  
206  
INTERIOR FEATURES  
Touch-screen audio system  
INFORMATION  
When using Bluetooth® audio and hands-free system at the same time  
The following problems may occur.  
•
•
The Bluetooth® connection may be cut.  
Noise may be heard on the Bluetooth® audio playback.  
About the phonebook in this system  
The following data is stored for every registered phone. When another phone is  
connected, you cannot read the registered data.  
•
•
•
Phonebook data.  
All of call history.  
Speed dial.  
When you delete the phone, the above-mentioned data is also dted.  
When transferring ownership of the vehicle  
Initialise the system to prevent personal data from being improperly accessed, refer to  
page 165.  
About Bluetooth®  
Bluetooth is a registered trademark of  
Bluetooth SIG, Inc.  
The Bluetooth wordmark and logo  
are owned by Bluetooth SIG. and  
permission has been granted tse the  
trademark of the licensee FUJITSU TEN  
LIMITED.  
Other trademarks and trade names are  
owned by various different owners.  
207  
INTERIOR FEATURES  
Touch-screen audio system  
INFORMATION  
Compatible models  
This system supports the following service.  
•
Bluetooth® Specification:  
Ver. 1.1 or higher (Recommended: Ver. 2.1+EDR or higher)  
•
Profiles:  
–
HFP (Hands Free Profile) Ver. 1.0 or higher (Recommended: Ver. 1.5 or higher)  
This is a profile to allow hands-free phone calls using the mobile phone or head  
sets. It has an outgoing and incoming call function  
–
–
OPP (Object Push Profile) Ver. 1.1 or higher.  
This is a profile to exchange phonebook data. When the Bluetooth® phone has  
PBAP and OPP, OPP cannot be used  
PBAP (Phone Book Access Profile) Ver. 1.0 or higher.  
This is a profile to transfer phonebook data  
If your mobile phone does not support HFP, you cannot enter the Bluetooth® phone. You  
need to take OPP or PBAP service individually.  
CAUTION  
Do not use the mobile phone or connect the luetooth® system while driving.  
NOTICE  
When leaving the vehicle  
Do not leave your mobile phone in the vehicle. The inside of the vehicle may become  
hot, causing damage to the phone.  
208  
INTERIOR FEATURES  
Touch-screen audio system  
USING THE BLUETOOTH® PHONE  
1
2
Device name  
Bluetooth® connection status  
3
Make a call  
To display the TELEPHONE screen shown above, press  
on the steering wheel or  
.
Registering a Bluetooth® phone  
To use the hands-free system, you must  
register a Bluetooth® phone in the system.  
You can register up to 5 phones in the  
system.  
1. Display the TELEPHONE screen.  
2. Touch YES.  
3. Input the passcode displayed on the  
screen into your phone.  
For the operation of the phone, see the  
manual that comes with your mobile  
phone.  
Passcodes are not required for SSP  
(Secure Simple Pairing) compatible  
Bluetooth® devices. Depending on  
the phone, you may need to select YES  
to register, or NO to cancel on your  
mobile phone.  
If you want to cancel it, select CANCEL.  
If a completion message is displayed, registration is complete.  
If an error message is displayed, follow the guidance on the screen to try again.  
209  
INTERIOR FEATURES  
Touch-screen audio system  
Selecting the Bluetooth® phone  
If multiple Bluetooth® devices are registered, follow the procedure below to select the  
Bluetooth® device to be used. You may only use one device at a time.  
1. Touch CONNECT TELEPHONE on the  
TELEPHONE screen.  
2. Touch the device to connect.  
ADD NEW: Registering a Bluetooth®  
device, refer to page 209.  
The selection indicator is displayed on  
left side of the selected device name.  
The Bluetooth® mark is displayed  
when you connect the device.  
When the system cannot get the  
device names, alternate names will be  
displayed such as DEVICE1, DEVICE2,  
etc.  
Connecting a Bluetooth® phone  
There are two connecting mhods available - automatic and manual.  
Automatic−  
When you register your phone, auto connection will be activated. Always set it to this  
mode and leave the Bluetooth® phone in a place where connection can be established.  
Vehicles with standard type ignition switch−  
When the ignition switch is turned to the ACC or ON position, the system will search for  
a nearby mobile phone you have registered.  
Vehicles with a smart entry and start system−  
When the ENGINE START STOP switch is in ACCESSORY or IGNITION ON mode, the  
system will search for a nearby mobile phone you have registered.  
Next, the system automatically connects with the most recent of the phones connected  
to in the past. Then, the connection result is displayed.  
210  
INTERIOR FEATURES  
Touch-screen audio system  
Manual−  
When the auto connection has failed or BLUETOOTH POWER is turned off, you must  
connect Bluetooth® manually.  
1. Touch CONNECT TELEPHONE on the  
TELEPHONE screen.  
2. Touch the device to connect.  
A message is shown if connection has  
been successful.  
If connection fails, a message will be  
displayed and connection will be  
re-attempted.  
INFORMATION  
Reconnecting to the Bluetooth® phone  
Vehicles with standartype ignition switch−  
If the system cannot connect due to poor signal strength with the ignition switch in the  
ACC or ON position, the system will automatically attempt to reconnect.  
Vehicles with a smart entry and start system−  
If the system cannot connect due to poor signal strength with the ENGINE START STOP  
switch in ACCESSORY or IGNITION ON mode, the system will automatically attempt to  
reconnect.  
If the phone is turned off, the system will not attempt to reconnect. In this case,  
connection must be made manually, or the phone must be re-selected.  
Connecting the phone while Bluetooth® audio is playing  
•
•
Bluetooth® audio will stop temporarily.  
It may take time to connect.  
211  
INTERIOR FEATURES  
Touch-screen audio system  
Making a call  
Once the Bluetooth® phone is registered, you can make a call using the following  
procedure:  
Dialing−  
1. Input the phone number on the  
TELEPHONE screen.  
To delete the inputted phone number,  
touch  
To enter + as the first digit, prolong  
the touch on [ +].  
.
*
2. Press  
touch  
on the steering wheel or  
on the screen.  
Dialing from the phonebook−  
You can dial a number from the phonebook data imported from your mobile phone. The  
system has one phonebook for each telephone. Up to 1000 entries may be stored in each  
phonebook, refer to page 219.  
1. Touch CONTACTS on the TELEPHONE  
screen.  
2. Choose the desired data to call from  
the list.  
If the phonebook is empty, a message  
will be displayed, refer to page 213.  
3. Choose the number and then press  
on the steering wheel or touch  
on the screen.  
212  
INTERIOR FEATURES  
Touch-screen audio system  
When the phonebook is empty−  
You can transfer the phone numbers in your Bluetooth® phone to the system.  
Operation methods differ between PBAP compatible and PBAP incompatible Bluetooth®  
phones. If your mobile phone does not support either PBAP or OPP service, you cannot  
transfer contacts.  
1. Touch CONTACTS on the TELEPHONE  
screen.  
2. If the phonebook is empty, a message  
will be displayed.  
3. For a PBAP compatible Bluetooth® phone−  
Touch YES if you want to transfer new contacts rom a mobile phone.  
Touch NO if you want to cancel transferring e contacts.  
For a PBAP incompatible and OPP compaible Bluetooth® phone−  
Touch TRANSFER if you want to trsfer new contacts from a mobile phone.  
Touch CANCEL if you want to cncel transferring the contacts.  
You need to operate your phone to transfer new contacts.  
Calling using speed dial−  
You can make a call usinnumbers  
registered from the phebook.  
1. Touch SPEED IAL on the  
TELEPHONE screen.  
Select the desired tab and choose the  
desired number to make a call.  
213  
INTERIOR FEATURES  
Touch-screen audio system  
Dialing from history−  
You can call using the call history which has the following 4 functions.  
ALL:  
All the calls below which were memorised.  
Calls which you missed.  
MISSED:  
INCOMING: Calls which you received.  
OUTGOING: Calls which you called.  
1. Touch CALL HISTORY on the  
TELEPHONE screen.  
2. Select the desired tab and choose the  
desired data from the list.  
3. Press  
touch  
on the steering wheel or  
on the screen.  
INFORMATION  
Call history list  
•
•
If you make a call to or receive a call from a number registered in the phonebook,  
the name is displayed in the call history.  
If you make multiple calls to the same number, only the last call made is displayed  
in the call history.  
When driving  
The functions DIALING, DIALING FROM THE PHONEBOOK, and DIALING FROM  
HISTORY (except for calls using the 5 most recently called numbers shown by ALL tab)  
are unavailable.  
International calls  
You may not be able to make international calls, depending on the mobile phone in use.  
214  
INTERIOR FEATURES  
Touch-screen audio system  
INFORMATION  
Calling by using the latest call history item  
1. Press  
2. Press  
3. Press  
on the steering wheel to display the TELEPHONE screen.  
on the steering wheel to display the CALL HISTORY screen.  
on the steering wheel to select the latest history item.  
on the steering wheel or touch on the screen to call the latest history  
4. Press  
item.  
Receiving a call  
When a call is received, the following  
screen is displayed together with a sound.  
To answer the phone:  
•
•
Press  
Touch  
on the steering wheel or,  
on the screen.  
To refuse a call  
•
•
Press  
Touch  
on the steering wheel or,  
on the screen.  
To adjust the incoming call volume−  
Touch [−] or [+]. You can also adjust he  
volume using the steering switches or  
volume knob.  
INFORMATION  
International calls  
Received internatinal calls may not be displayed correctly depending on the mobile  
phone in use.  
Speaking on the phone  
The following screen is displayed when  
speaking on the phone.  
215  
INTERIOR FEATURES  
Touch-screen audio system  
To adjust the incoming call volume−  
Touch [−] or [+]. You can also adjust the volume using the steering switches or the  
volume knob.  
To prevent the other party from hearing your voice−  
Touch MUTE.  
Inputting tones−  
When using phone services such as an  
answering service or a bank, you can  
store phone numbers and code numbers  
in the phonebook.  
1. Touch [0-9].  
2. Input the number.  
3. If repeated tone symbols* are stored  
in the phone book, SEND and EXIT  
are displayed on the right side of the  
screen.  
*: Repeated tone symbols are symbols  
or numbers displayed as p or w,  
that come after the phone number.  
(e.g. 056133w0123p#1*)  
4. Confirm the number displayd on the  
screen, and touch SEND.  
If you touch EXIT, this fction will  
end.  
To transfer a call−  
Touch HANDSET MODE to change from hands-free call to mobile phone call.  
Touch HANDS-FREE MODE to change from mobile phone call to hands-free call.  
To hang up−  
Press  
on the steering wheel or touch  
on the screen.  
216  
INTERIOR FEATURES  
Touch-screen audio system  
Call waiting  
When a call is interrupted by a third party  
while talking, the incoming call message  
will be displayed.  
To talk with the other party:  
•
•
Press  
Touch  
on the steering wheel or,  
on the screen.  
To refuse the call:  
•
•
Press  
Touch  
on the steering wheel or,  
on the screen.  
Every time you press  
wheel or touch  
on the steering  
on the screen during  
call waiting, you will be switched to the  
other party.  
INFORMATION  
Transferring calls  
•
•
It is not possible to transfer from hands-free to the mobile phone while driving.  
If you transfer from the mobile phone tands-free, the hands-free screen will be  
displayed, and you can operate the stem using the screen.  
•
•
Transfer method and operation may vary according to the mobile phone used.  
For operation of the mobile phone in use, see the phone’s manual.  
Call waiting operation  
Call waiting operation madiffer depending on your phone company and mobile phone.  
217  
INTERIOR FEATURES  
Touch-screen audio system  
SETTING THE HANDS-FREE SYSTEM  
You can set the hands-free system to your desired settings.  
1. Setting the sound.  
2. Phonebook settings.  
To display the TELEPHONE SETTINGS screen showabove, press SETUP, and touch  
TELEPHONE on the SETUP screen.  
Setting the sound  
1. Touch SOUND SETTINGS on the  
TELEPHONE SETTINGS screen.  
a. Changes the call volume.  
a
b. Changes the ring tone volume.  
c. Changes the ring tone.  
b
c
d. Restore default settings.  
HINT: Refer to the following rocedures for  
details.  
d
STNDA0057Ea  
Setting the volume−  
1. Touch CALL VOLUME or RING TONE  
VOLUME on the SOUND SETTINGS  
screen.  
2. Touch [−] or [+] to lower or raise the  
volume, and then OK.  
3. When you complete all settings, touch  
OK.  
218  
INTERIOR FEATURES  
Touch-screen audio system  
Setting the ring tone−  
1. Touch RING TONE on the SOUND  
SETTINGS screen.  
2. Touch TONE 1, TONE 2 or TONE 3 to  
change the ring tone, and then OK.  
3. When you complete all settings, touch  
OK.  
INFORMATION  
To return to the default volume settings  
Touch DEFAULT, and then YES.  
Phonebook settings  
The phonebook manages a maximum of 5 phones in totalThe data for 1000 contacts (up  
to 3 numbers per contact) can be registered in each onebook.  
a
b
c
STNDA00060Ea  
To display the screen above, follow the steps below.  
1. Display the TELEPHONE SETTINGS screen, refer to page 218.  
2. Touch PHONEBOOK on the TELEPHONE SETTINGS screen.  
a. Managing the contacts.  
b. Managing the speed dials.  
c. Deleting the call history.  
219  
INTERIOR FEATURES  
Touch-screen audio system  
Managing the contacts−  
Transferring a phone number:  
You can transfer the phone numbers in your Bluetooth® phone to the system. Operation  
methods differ between PBAP compatible and PBAP incompatible Bluetooth® phones.  
If your mobile phone does not support either PBAP or OPP services, you cannot transfer  
contacts.  
1. Touch MANAGE CONTACTS on the  
PHONEBOOK SETTINGS screen.  
2. Touch TRANSFER CONTACTS.  
3. For PBAP compatible Bluetooth®  
phones−  
Touch required selection.  
a. Automatic phonebook download  
on / off.  
b
The phonebook data can be  
automatically transferred.  
c
Depending on the mobile phone,  
call history will be also transferred.  
STNDA00062Ea  
b. Update phonebook.  
The phonebook dta can be  
updated.  
c. Restore default settings.  
For PBAP incompatible Bluetooth®  
phones−  
Touch required selection.  
a. Replace contacts.  
a
The phonebook data can be  
replaced.  
b
b. Add contacts  
The phonebook can be added.  
STNDA00063Ea  
220  
INTERIOR FEATURES  
Touch-screen audio system  
Deleting the phonebook data:  
1. Touch MANAGE CONTACTS on the  
PHONEBOOK SETTINGS screen.  
2. Touch DELETE CONTACTS.  
If your phone supports PBAP service,  
AUTOMATIC PHONEBOOK  
DOWNLOAD setting needs to be set to  
OFF, refer to page 220.  
3. Choose the data to delete.  
To delete all data, touch ALL DELETE.  
4. A confirmation message will be  
displayed. If everything is correct,  
touch YES.  
INFORMATION  
Phonebook data  
Phonebook data is managed fovery registered phone. When another phone is  
connecting, you cannot read the registered data.  
Setting the phonebook in a different way (To display the CONTACTS screen)  
1. Display the TELEPHONE screen, refer to page 209.  
2. Touch CONTACTS on the TELEPHONE screen.  
3. Touch OPTIONS on the CONTACTS screen.  
4. Touch MANAGE CONTACTS on the PHONEBOOK SETTINGS screen.  
When transferring a phone number  
Transfer the phone number while the engine is running.  
If your mobile phone is OPP or PBAP compatible, you may need to input [1234] by your  
mobile phone for OBEX certification.  
When you have selected UPDATE PHONEBOOK to transfer the phone number  
•
•
If your mobile phone does not support PBAP service, you cannot use this function.  
If your phone supports PBAP service, you can transfer the phonebook data without  
operating your phone.  
221  
INTERIOR FEATURES  
Touch-screen audio system  
INFORMATION  
When you have selected REPLACE CONTACTS or ADD CONTACTS to transfer the  
phone number  
If your mobile phone does not support OPP service, you cannot use these functions. You  
can transfer the phonebook data only by operating your phone  
Transferring the phone number in a different way (To display the CONTACT  
TRANSFER METHOD screen)  
1. Display the TELEPHONE screen, refer to page 209.  
2. Touch CONTACTS on the TELEPHONE screen.  
3. Touch TRANSFER on the CONTACTS screen.  
Transferring the phone number while Bluetooth® audio is playing  
Bluetooth® audio will disconnect. It will reconnect automatically whdata transfer  
finishes. It may not reconnect, depending on the phone you are using.  
Deleting the phonebook data in a different way  
1. Display the TELEPHONE screen, refer to page 209.  
2. Touch CONTACTS on the TELEPHONE screen.  
3. Choose the desired data from the list.  
4. Touch OPTIONS on the CONTACT screen.  
5. Touch DELETE on the CONTACT DAA screen.  
6. A confirmation message will be displayed. If everything is correct, touch YES.  
If your phone supports PBAP sere, AUTOMATIC PHONEBOOK DOWNLOAD setting  
needs to be set to OFF, refer to page 220.  
When you delete a Bluetoth® phone, the phonebook data will be deleted at the same  
time.  
Managing the speed dials−  
Registering the speed dial from contacts:  
You can register the desired phone  
number from the phonebook. Up to 18  
numbers per phone can be registered.  
1. Touch MANAGE SPEED DIALS on the  
PHONEBOOK SETTINGS screen.  
2. Touch NEW SPEED DIAL FROM  
CONTACTS.  
222  
INTERIOR FEATURES  
Touch-screen audio system  
3. Choose the data to register.  
4. Touch the desired phone number.  
5. Touch the switch you want to registe
the number in.  
6. If you select a switch you registered  
before, a confirmation mesge will be  
displayed. If you want to replace it,  
touch YES.  
Registering the speed dial from call  
history:  
1. Touch MANAGE SPEED DIALS on the  
PHONEBOOK SETTINGS screen.  
2. Touch NEW SPEED DIAL FROM CALL  
HISTORY.  
223  
INTERIOR FEATURES  
Touch-screen audio system  
3. Choose the data to register.  
4. Touch the switch you want to register  
the number in.  
5. If you select a switch you registered  
before, a confirmation message will be  
displayed. If you want to replace it,  
touch YES.  
Deleting the speed dial:  
1. Touch MANAGE SPEED DIALS on the  
PHONEBOOK SETTINGS screen.  
2. Touch DELETE SPEED DIALothe  
SPEED DIALS screen.  
3. Choose the data to dele.  
To delete all data, uch ALL DELETE.  
4. A confirmation message will be  
displayed. If everything is correct,  
touch YES.  
INFORMATION  
Setting the speed dials in a different way (From SPEED DIAL screen)  
1. Display the TELEPHONE screen, refer to page 209.  
2. Touch SPEED DIALS on the TELEPHONE screen.  
3. Touch OPTIONS on the SPEED DIAL screen.  
224  
INTERIOR FEATURES  
Touch-screen audio system  
INFORMATION  
Setting the speed dials in a different way (From CONTACTS screen)  
1. Display the TELEPHONE screen, refer to page 209.  
2. Touch CONTACTS on the TELEPHONE screen.  
3. Touch OPTIONS on the CONTACTS screen.  
4. Touch MANAGE SPEED DIALS on the PHONEBOOK SETTINGS screen.  
Registering the speed dial in a different way (From SPEED DIAL screen)  
1. Display the TELEPHONE screen, refer to page 209.  
2. Touch SPEED DIALS on the TELEPHONE screen.  
3. Touch (ADD NEW) on the SPEED DIAL screen.  
4. Touch CONTACTS or HISTORY to set new speed dial.  
Touch CANCEL to cancel it.  
5. Choose the desired data from the list.  
6. Touch the desired phone number.  
7. Follow the steps REGISTERING THE SPEED DIFROM CONTACTS from Step 6  
on page 223 or REGISTERING THE SPEED DL FROM CALL HISTORY from Step 5 on  
page 224.  
Registering the speed dial in a differeway (From CONTACT screen)  
1. Display the TELEPHONE screen, efer to page 209.  
2. Touch CONTACTS on the TELEPHONE screen.  
3. Choose the desired datfrom the list.  
4. Touch OPTIONS on the CONTACT screen.  
5. Touch SET SPEED IAL on the CONTACT DATA screen.  
6. Touch the desied telephone number.  
7. Follow the steps REGISTERING THE SPEED DIAL FROM CONTACTS from Step 6  
on page 223 or REGISTERING THE SPEED DIAL FROM CALL HISTORY from Step 5 on  
page 224.  
Registering the speed dial in a different way (From CALL HISTORY screen)  
1. Display the TELEPHONE screen, refer to page 209.  
2. Touch CALL HISTORY on the TELEPHONE screen.  
3. Choose the desired data from the list.  
4. Touch ADD SPEED DIAL on the CALL HISTORY screen.  
5. Follow the steps REGISTERING THE SPEED DIAL FROM CONTACTS from Step 6  
on page 223 or REGISTERING THE SPEED DIAL FROM CALL HISTORY from Step 5 on  
page 224.  
225  
INTERIOR FEATURES  
Touch-screen audio system  
Deleting the call history−  
1. Display the PHONEBOOK SETTINGS  
screen, refer to page 219.  
2. Touch DELETE CALL HISTORY on the  
PHONEBOOK SETTINGS screen.  
If your phone supports PBAP service,  
the AUTOMATIC PHONEBOOK  
DOWNLOAD setting needs to be set to  
OFF, refer to page 220.  
3. Choose the desired history to delete.  
4. Choose the data to delete.  
To delete all data, touch ALL DELETE.  
5. A confirmation message will be  
displayed. If everything is correct,  
touch YES.  
INFORMATION  
Deleting call history in a different way  
1. Display the TELEPHONE screrefer to page 209.  
2. Touch CALL HISTORY on the TELEPHONE screen.  
3. Touch DELETE on the CALL HISTORY screen.  
4. Follow the steps DEETING THE CALL HISTORY above.  
226  
INTERIOR FEATURES  
Touch-screen audio system  
BLUETOOTH® SETTINGS  
You can set the Bluetooth® system to your desired settings.  
1
2
Registered devices settings  
Connecting telephone  
3
4
Connecting audio player  
Detailed Bluetooth® settings  
To display the BLUETOOTH SETTINGS screen shown above, press SETUP, and touch  
BLUETOOTH on the SETUP screen.  
Registered devices settings  
Registering a Bluetooth® device−  
Bluetooth® devices compatible with  
phones (HFP) and portable audio players  
(AVP) can be registered simltaneously.  
You can register up to 5 Bluetooth®  
devices.  
1. Touch REGISTERD DEVICES on the  
BLUETOOTH SETTINGS screen.  
2. Touch ADD NEW.  
227  
INTERIOR FEATURES  
Touch-screen audio system  
3. When this screen is displayed, input  
the passcode displayed on the screen  
into your Bluetooth® device.  
For the operation of the Bluetooth®  
device, see the manual that comes  
with your Bluetooth® device.  
Passcodes are not required for SSP  
(Secure Simple Pairing) compatible  
Bluetooth® devices. Depending on the  
phone, you may need to select YES  
to register, or NO to cancel on your  
mobile phone.  
If you want to cancel it, touch  
CANCEL.  
If a completion message is displayed,  
registration is complete.  
If an error message is displayed,  
follow the guidance on the screen to  
try again.  
Removing a Bluetooth® device−  
1. Touch REGISTERED DEVICES on the  
BLUETOOTH SETTINGS screen.  
2. Touch REMOVE.  
3. Touch the device to remove.  
4. A confirmation message will be  
displayed, touch YES to remove the  
device.  
228  
INTERIOR FEATURES  
Touch-screen audio system  
Displaying a Bluetooth® device details−  
You can confirm and change the device  
details.  
1. Touch REGISTERED DEVICES on the  
BLUETOOTH SETTINGS screen.  
2. Touch DETAILS.  
3. Touch the device.  
4. The following screen is displayed:  
a. Display device name.  
b. Display device address.  
a
c. Display your telephone mber.  
b
c
The number may not be displayed  
depending on the phones.  
d
d. Display comptibility profile of the  
device.  
f
e. Change connection method, refer  
to page 230.  
STNDA00077Ea  
f. Restore default settings.  
5. When you complete settings, touch  
OK.  
e
f
STNDA00078Ea  
229  
INTERIOR FEATURES  
Touch-screen audio system  
Changing connection method:  
1. Touch CONNECTION METHOD on the  
DEVICE DETAILS screen.  
2. Touch FROM VEHICLE or FROM  
AUDIO PLAYER.  
FROM VEHICLE: Connect the audio  
system to the portable audio player.  
FROM AUDIO PLAYER: Connect the  
portable audio player to the audio  
system.  
Selecting the Bluetooth® phone  
If multiple Bluetooth® devices are registered, follow the procedure below to select the  
Bluetooth® device to be used. You may only use one device at a time.  
1. Touch CONNECT TELEPHONE on the  
BLUETOOTH SETTINGS screen.  
2. Touch the device to connect.  
ADD NEW: Registering a Bluetooth®  
device, refer to page 227.  
The selection indicator is displayed on  
left side of the selected device name.  
The Bluetooth® mark is displayed  
when you connect the device.  
Selecting the audio player  
If multiple Bluetooth® devices are registered, follow the procedure below to select the  
Bluetooth® device to be used. You may only use one device at a time.  
1. Touch CONNECT AUDIO PLAYER on the BLUETOOTH SETTINGS screen.  
2. Touch the device to connect.  
ADD NEW: Registering a Bluetooth®  
device, refer to page 227.  
The selection indicator is displayed on  
left side of the selected device name.  
The Bluetooth® mark is displayed when you  
connect the device.  
230  
INTERIOR FEATURES  
Touch-screen audio system  
Detailed Bluetooth® settings  
You can confirm and change the detailed  
Bluetooth® settings.  
1. Touch DETAILED BLUETOOTH  
SETTINGS on the BLUETOOTH  
SETTINGS screen.  
a
2. The following screen is displayed:  
a. Change Bluetooth® power on / off  
b
c
d
You can change Bluetooth®  
function to ON or OFF.  
f
b. Display device name.  
h
STNDA00081Ea  
c. Change passcode, refer to page 231.  
d. Display device address.  
e. Display compatibility profile of the  
system.  
e
f. Change displaying telephone  
status on / off.  
f
g
You can set the system to show the  
status confirmation display when  
connecting a telephone.  
h
g. Change displaying audio playe
status on / off.  
STNDA00082Ea  
You can set the system tshow the status confirmation display when connecting  
an audio player.  
h. Restore default ttings.  
3. When you comlete settings, touch OK.  
Editing the passcode  
You can change the passcode that you use  
to register your Bluetooth® device in the  
system.  
1. Touch PASSCODE on the DETAILED  
BLUETOOTH SETTINGS screen.  
2. Input a passcode, and touch OK.  
231  

Related Topics

INTERIOR FEATURES

Using the air conditioning system and defogger
Using the interior lights
Using the storage features
Other interior features (Clock, Power outlet, etc)

Popular Owner Manuals

Audi
BMW
Citroen
Ford
Honda
Peugeot

Latest Owner Manuals

Fourth Generation (2021-2026) Skoda Fabia 4 Door Fourth Generation (2021-2026) Skoda Fabia 4 Door
Second Generation (2013-2019) Hyundai I10 4 Door Second Generation (2013-2019) Hyundai I10 4 Door
First Generation (2007-2012) Hyundai I10 4 Door First Generation (2007-2012) Hyundai I10 4 Door
Second Generation (2022-2026) Volvo XC40 SUV Second Generation (2022-2026) Volvo XC40 SUV
Fifth Generation (2023-2026) Toyota Prius 4 Door Fifth Generation (2023-2026) Toyota Prius 4 Door
Fourth Generation (2016-2022) Toyota Prius 4 Door Fourth Generation (2016-2022) Toyota Prius 4 Door
→