Get BODY -> Instrument Panel Guide for Toyota Avensis 4 Door First Generation (1997-2003)

BO–5

BODY

–

INSTRUMENTPANEL

INSTRUMENT PANEL

BO19J–03

COMPONENTS

w/ Curtain shield air bag:

Front Pillar Garnish

Curtain Shield Airbag

G

Reinforcement

C

G

Front Pillar Garnish

w/ Curtain shield

air bag:

Front Pillar Garnish

No. 1 Brace

G

A

Instrument Panel

H

E

Front Door Opening Trim

H

D

H

18 (185, 13)

E

Rear Door Opening Trim

E

Front Pillar Garnish

D

No. 1 Register

Cowl Side Trim

Combination Meter

Cluster Finish Panel

Front Door Scuff Plate

E

Center Pillar Lower Garnish

Rear Door Scuff Plate

Lower Finish Panel

Column Cover

Center Cluster

E

Finish Panel

Glove Compartment Door

E

50(510, 37)

x 3

No. 1 Under Cover

M/T:

Shift Knob

F

Combination Switch

Steering Wheel

Steering Wheel Pad

F

Rear Console Box

B

E

B

Parking Brake Hole Cover

Box Bottom Mat

No. 2 Box Bottom Mat

Box Bottom Panel

Cowl Side Trim

Front Door Scuff Plate

Center Pillar Lower Garnish

Rear Door Opening Trim

N·m (kgf·cm, ft·lbf) : Specified torque

H15309

AVENSIS/CORONA SUP (RM781E)

BO–6

BODY

–

INSTRUMENTPANEL

Defroster Nozzle

No. 2 Side Defroster Duct

E

No. 1 Side Defroster Duct

E

No. 3 Heater to Register Duct

No. 4 Heater to Register Duct

E

Front Passenger

Airbag Assembly

E

No. 1 Pin

E

No. 2 Side Defroster

Nozzle

No.1 Heater to

Register Duct

E

No. 2 Register

Center Bracket

E

RadioTunerMounting Bracket

E

Front Ash Receptacle

Wire Harness

H15308

AVENSIS/CORONA SUP (RM781E)

BO–7

BODY

–

INSTRUMENTPANEL

HINT:

Screw shapes and size are indicated in the table below. The codes (A – H) correspond to those indicated

on the previous page.

mm (in.)

Shape

Size

Shape

Size

Shape

Size

ø = 8

ø = 6

(0.31)

(0.24)

L = 16

(0.63)

L = 20

(0.79)

L = 18

(0.71)

ø = 5

(0.20)

ø = 5.22

(0.2055)

ø = 6

(0.24)

L = 18.5

(0.728)

L = 16

(0.63)

L = 16

(0.63)

ø = 8

(0.31)

ø = 6

(0.24)

H03703

AVENSIS/CORONA SUP (RM781E)

BO–8

BODY

–

INSTRUMENTPANEL

BO3VQ–01

REMOVAL

1.

2.

REMOVE FRONT DOOR OPENING TRIMS

REMOVE FRONT PILLAR GARNISHES

(a) w/ Curtain Shield Airbag:

(1) Remove the 2 bolts.

(2) Pack the airbag with protection cover.

(3) Using a screwdriver, raise the pillar garnish cover.

(4) Remove the bolt, pillar garnish cover and front pillar

garnish.

NOTICE:

Protection rang is from instrument panel to ceiling.

(b) Remove the front door scuff plates.

(c) Remove the cowl side trims.

I12491

(d) Remove the rear door opening trims.

(e) Remove the rear door scuff plates.

(f)

Remove the center pillar lower covers.

(g) Remove the front seats.

3.

REMOVE STEERING WHEEL (See page SR–6)

4.

REMOVE LOWER FINISH PANEL

(a) Remove the 2 screws and hood lock control lever.

(b) Remove the 2 screws and lower finish panel.

5.

6.

REMOVE COLUMN COVER (See page SR–6)

REMOVE COMBINATION SWITCH (See page

SR–6)

7.

REMOVE STEERING COLUMN (See page SR–6)

H03659

8.

REMOVE CLUSTER FINISH PANEL

: 4 Clips

(a) Remove the 2 screws.

(b) Using a screwdriver, remove the cluster finish panel, then

disconnect the connector.

HINT:

Tape the screwdriver tip before use.

9.

REMOVE COMBINATION METER

H03660

AVENSIS/CORONA SUP (RM781E)

BO–9

BODY

–

INSTRUMENTPANEL

10. REMOVE NO. 1 REGISTER

Using a screwdriver, remove the No. 1 register.

HINT:

: 4 Clips

Tape the screwdriver tip before use.

H03661

H16639

H16437

H16640

H03664

11. REMOVE NO. 1 UNDER COVER

Using a screwdriver, remove the No. 1 under cover.

HINT:

: 3 Clips

Tape the screwdriver tip before use.

12. REMOVE GLOVE COMPARTMENT DOOR

(a) Remove the damper clip from the bracket as shown in the

illustration.

(b) Remove the 2 glove shaft and glove compartment door.

13. REMOVE PARKING BRAKE HOLE COVER

14. REMOVE REAR CONSOLE BOX

(a) M/T:

Remove the shift lever knob.

(b) Remove the box bottom mat, No. 2 box bottom mat and

box bottom panel.

(c) Remove the 2 bolts, 4 caps, 4 screws and rear console

box.

AVENSIS/CORONA SUP (RM781E)

BO–10

BODY

–

INSTRUMENTPANEL

15. REMOVE CENTER CLUSTER FINISH PANEL

(a) Using a screwdriver, remove the 6 clips of the centerclus-

ter finish panel.

: 6 Clips

HINT:

Tape the screwdriver tip before use.

H15310

(b) Remove the center cluster finish panel with holding up as

shown in the illustration.

(c) Disconnect the connectors.

H16288

16. REMOVE INSTRUMENT PANEL

(a) Remove the 2 bolts and front passenger airbag assembly.

(b) Remove the 6 screws and 3 nuts.

H03666

17. REMOVE NO. 1 BRACE

18. REMOVE REINFORCEMENT

AVENSIS/CORONA SUP (RM781E)

BO–11

BODY

–

INSTRUMENTPANEL

BO2J4–02

INSTALLATION

1.

2.

INSTALL REINFORCEMENT

INSTALL NO. 1 BRACE

3.

INSTALL INSTRUMENT PANEL

(a) Install the 6 screws and 3 nuts.

(b) Install the passenger airbag assembly with the 2 bolts.

Torque: 18 N·m (185 kgf·cm, 13 ft·lbf)

H03666

4.

INSTALL CENTER CLUSTER FINISH PANEL

: 6 Clips

Install the panel, then connect the connectors.

H15310

H03664

H16640

5.

INSTALL REAR CONSOLE BOX

(a) Install the console box with the 2 bolts and 4 caps, 4

screws.

(b) Install the box bottom panel, No. 2 box bottom mat and

box bottom mat.

(c) M/T:

Install the shift lever knob.

INSTALL PARKING BRAKE HOLE COVER

6.

7.

INSTALL GLOVE COMPARTMENT DOOR

(a) Install the glove compartment door with the 2 glove shaft.

(b) Install the damper clip.

AVENSIS/CORONA SUP (RM781E)

BO–12

BODY

–

INSTRUMENTPANEL

8.

INSTALL NO. 1 UNDER COVER

: 3 Clips

Install the No. 1 under cover.

H16639

H03661

H03660

9.

INSTALL NO. 1 REGISTER

: 3 Clips

Install the No. 1 register.

10. INSTALL COMBINATION METER

11. INSTALL CLUSTER FINISH PANEL

(a) Install the cluster finish panel, then connect the connec-

tor.

: 3 Clips

(b) Install the 2 screws.

12. INSTALL STEERING COLUMN (See page SR–6)

13. INSTALL COMBINATION SWITCH (See page SR–6)

14. INSTALL COLUMN COVER (See page SR–6)

15. INSTALL LOWER FINISH PANEL

(a) Install the lower finish panel with the 2 screws.

(b) Install the hood lock control lever.

H03659

AVENSIS/CORONA SUP (RM781E)

BO–13

BODY

–

INSTRUMENTPANEL

16. INSTALL STEERING WHEEL (See page SR–6)

17. INSTALL FRONT SEATS

Torque: 37 N·m (375 kgf·cm, 27 ft·lbf)

18. INSTALL CENTER PILLAR LOWER COVERS

19. INSTALL REAR DOOR SCUFF PLATES

20. INSTALL REAR DOOR OPENING TRIMS

21. INSTALL COWL SIDE TRIMS

22. INSTALL FRONT DOOR SCUFF PLATES

(a) w/ Curtain Shield Airbag:

(1) Remove the protection cover.

(2) Install the 2 bolts.

Torque: 5.0 N·m (51 kgf·cm, 44 in.·lbf)

(3) Install the pillar garnish cover with the bolt.

NOTICE:

Be sure to tighten the bolt.

(4) Fell the pillar garnish cover.

(b) Install the front pillar garnishes.

(c) Install the front door opening trims.

I12491

AVENSIS/CORONA SUP (RM781E)

BODY -> Instrument Panel for Your Toyota Avensis 4 Door First Generation (1997-2003)

Related Topics

BODY

Popular Owner Manuals

Latest Owner Manuals