Driving and operating -> Charging for Your Vauxhall Astra 4 Door Eight Generation (2022-2026)

186  
Driving and operating  
domestic electrical outlet, a  
Green'Up outlet, a wall box or a public  
charging station.  
System limitations  
In the following situations, the system  
may not operate properly or even not  
operate at all:  
Charging  
General information  
The high voltage battery can be  
charged with direct current (DC) only.  
When charging from a domestic  
electrical outlet, a wall box or an  
alternating current (AC) charging  
station, AC has to be converted into  
DC. This is done by the vehicle's  
onboard charger.  
PHEV: The onboard charger (single-  
phase) is available with 3.7 kW or  
7.4 kW.  
BEV: The onboard charger (3-phase)  
is available with 11 kW.  
9 Warning  
poor visibility caused by  
inadequate lighting of the  
roadway, falling snow, heavy  
rain, dense fog etc.  
Persons with a pacemaker should  
consult a doctor for possible  
precautions.  
dazzle caused by headlamps of  
oncoming vehicles, low sun,  
reflections on damp roads,  
leaving a tunnel, alternating  
shade and light etc.  
Charging the vehicle's high voltage  
battery depends upon several factors:  
windscreen area in front of the  
camera covered by dirt, snow,  
stickers etc.  
no lane markings detected or  
multiple lane markings due to  
roadworks  
Propulsion types 3 4.  
The speed of charging the vehicle's  
high voltage battery depends upon  
the weakest element of the charging  
chain. To achieve the maximum  
charging speed, charging cable and  
charging device have to be attuned to  
each other.  
high voltage battery of the vehicle  
internal onboard charger (OBC)  
external charging device  
charging cable  
close vehicles ahead  
winding roads or narrow roads  
when advanced lane keep assist  
is active  
The charging cable connects the  
vehicle's high voltage battery with an  
external charging device providing  
electric power. This may be a  
Notice  
Make sure that the charging cable  
used fits to the vehicle's onboard  
charger.  
Driving and operating  
187  
Charging types 3 187.  
Charging cable 3 194.  
BEV: Charging time takes approx.  
five hours with the 11 kW onboard  
charger.  
Charging types  
There are different types of charging  
the vehicle's high voltage battery.  
Charging times refer to charging an  
empty battery until it is completely  
charged.  
Electric power consumption and  
range  
The electric power consumption  
(combined under WLTP condition) is  
within a range of 15.6 to 14.6 kWh/  
100 km.  
Propulsion types 3 4.  
Charging at DC charging stations  
Charging at wall boxes / AC  
charging stations  
A wall box / AC charging station may  
or may not provide a charging cable  
which has to be connected to the  
vehicle's charging port.  
The all electric range is up to 38 miles  
(PHEV) / 261 miles (BEV).  
Propulsion types 3 4.  
Up to approx. 80% of battery capacity  
may be charged in approx. 30  
minutes at a charging power of  
100 kW.  
For the values specific to your  
vehicle, refer to the EEC Certificate of  
Conformity provided with your vehicle  
or other national registration  
documents.  
The determination of electric power  
consumption is regulated by directive  
R (EC) No. 715/2007 and No.  
2017/1151 (in the latest applicable  
version).  
Charging at Green'Up outlets  
The high voltage battery can be  
charged at a Green'Up outlet.  
Connect the charging cable to the  
vehicle's charging port and to the  
Green'Up outlet.  
PHEV: Charging time takes approx.  
three hours and 55 minutes.  
PHEV: Charging time takes approx.  
three hours and 25 minutes with the  
3.7 kW onboard charger and 16 A.  
For the 7.4 kW onboard charger with  
32 A, charging time takes approx. one  
hour and 40 minutes.  
188  
Driving and operating  
Charging at domestic electrical  
outlets  
9 Warning  
9 Warning  
Improper use of portable charging  
cables may cause a fire, electrical  
shock, or burns, and may result in  
damage to property, serious  
injury, or death.  
Read all the safety warnings and  
instructions before using this  
product. Failure to follow the  
warnings and the instructions may  
result in electric shock, fire, and /  
or serious injury.  
Never leave children unattended  
near the vehicle while the vehicle  
is charging and never allow  
children to play with the charging  
cable.  
If the plug provided does not fit the  
electrical outlet, do not modify the  
plug. Arrange for a qualified  
electrician to inspect the electrical  
outlet.  
Do not use extension cables,  
multi-outlet power strips,  
splitters, grounding adaptors,  
surge protectors, or similar  
devices.  
The high voltage battery can be  
charged at a domestic electrical  
outlet. Connect the charging cable to  
the vehicle's charging port and to the  
domestic electrical outlet.  
PHEV: Charging time takes approx.  
seven hours and five minutes.  
BEV: Charging time takes approx.  
30 hours.  
Propulsion types 3 4.  
Do not use an electrical socket  
that is worn or damaged, or one  
that will not hold the plug firmly  
in place.  
Do not immerse the charging  
cable into any liquid.  
Do not put fingers into the electric  
vehicle connector.  
Do not use an electrical socket  
that is not properly grounded.  
Do not use an electrical socket  
that is on a circuit with other  
electrical loads.  
Charging cable  
Depending on the charging type,  
different charging cables are used.  
Driving and operating  
189  
Enhanced domestic cables (mode 2)  
are similar to basic domestic cables  
(mode 2). However, the charging  
performance of enhanced domestic  
cables (mode 2 charging) is better  
than the charging performance of  
basic domestic cables (mode 2).  
Enhanced domestic cables (mode 2)  
are used at Green'Up sockets which  
have to be installed by a certified  
electrician at the customer's site.  
Basic domestic cable (mode 2) /  
enhanced domestic cable (mode  
2)  
9 Danger  
There is a risk of electric shock  
that may cause personal injury or  
death.  
Do not use the charging cable if  
any part of the charging cable is  
damaged.  
Do not open or remove the  
charging cable cover.  
Service by qualified personnel  
only. Connect the charging cable  
to a properly grounded outlet with  
cables that are not damaged.  
Charging cable status indicators  
After plugging in the charging cable,  
it will perform a quick self test and all  
status indicators illuminate for a  
moment. For the functions of the  
status indicators, refer to the manual  
of the charging cable manufacturer.  
1. Vehicle plug  
2. Status indicators  
3. Wall plug  
Basic domestic cables (mode 2) are  
used for charging at domestic  
electrical outlets. A basic domestic  
cable (mode 2) consists of a vehicle  
plug, a control box and a plug for the  
domestic electrical outlet. The control  
box has an intergrated charge  
controller and several LEDs  
indicating the charging status.  
Important information about  
portable electric vehicle charging  
Charging an electric vehicle can  
stress a building's electrical  
system more than a typical  
household appliance.  
Before you plug in to any  
electrical outlet, have a qualified  
electrician inspect and verify the  
190  
Driving and operating  
electrical system (electrical  
outlet, wiring, junctions and  
protection devices) for heavy-  
duty service at a 10 A continuous  
load.  
Electrical outlets may wear out  
with normal usage or be  
damaged over time, making them  
unsuitable for electric vehicle  
charging.  
Mode 3 charging cable  
Mode 4 charging cable  
Notice  
Only use DC charging cables shorter  
than 30 metres.  
Mode 4 charging cables are used for  
DC charging. Since mode 4 charging  
cables are integrated within DC  
charging stations, they only provide a  
vehicle plug.  
Check the electrical outlet / plug  
while charging and discontinue  
use if the electrical outlet / plug is  
hot, then have the electrical  
outlet serviced by a qualified  
electrician.  
When outdoors, plug into an  
electrical outlet that is weather-  
proof while in use.  
Charging  
9 Warning  
1. Vehicle plug  
2. Plug for wall box / AC charging  
Persons with a pacemaker or  
similar devices should consult a  
doctor for possible precautions.  
If in doubt, during charging do not  
remain inside or near the vehicle,  
near the charging cable or the  
charging unit.  
station  
Mode 3 charging cables are used for  
charging at wall boxes and AC  
charging stations. A mode 3 charging  
cable provides a vehicle plug and a  
plug for the wall box / AC charging  
station. Wall boxes / AC charging  
stations may provide an integrated  
mode 3 charging cable. For more  
information on the mode 3 charging  
cable, refer to the manual of the  
charging cable manufacturer.  
Mount the charging cable to  
reduce strain on the electrical  
outlet / plug.  
In order to ensure the compatibility of  
plug and outlet, a label is used. The  
label is located on the inside of the  
vehicle's charging port flap. Make  
sure to connect only a cable of the  
same type.  
Driving and operating  
191  
may not provide an integrated  
charging cable. In this case, a  
portable mode 3 charging cable is  
required.  
Make sure that the electrical  
outlet, the plug and the cable do  
not support the weight of the  
control box.  
9 Warning  
9 Warning  
Type 2 plug or outlet used for AC  
charging  
When charging at a domestic  
electrical outlet, only use an outlet  
which is properly grounded and  
protected by a 30 mA differential  
switch.  
The engine does not start if the  
charging cable is connected to the  
vehicle. A warning is displayed in  
the Driver Information Centre.  
During the charging process,  
unlocking the vehicle will interrupt  
charging. If no action is taken on  
tailgate, the doors or the charging  
nozzle, the vehicle will lock again  
after 30 seconds and charging will  
resume automatically.  
Do not work in the engine  
compartment. Some areas remain  
very hot, even an hour after  
charging and the fan may start at  
any time.  
Only use a domestic electrical  
outlet protected by a circuit  
breaker adapted to the amperage  
of the electrical circuit.  
Have a qualified electrician check  
the electrical installation to be  
used. The installation has to be in  
compliance with national  
standards and compatible with the  
vehicle.  
FF plug or outlet used for DC charging  
9 Warning  
Avoid any entry of fluids into the  
charging port of the vehicle, the  
vehicle plug of the charging cable  
and the domestic electrical outlet.  
When using a dedicated domestic  
electrical outlet, have it installed  
by a qualified electrician.  
When charging at a public AC  
charging station / public DC charging  
station, follow the instructions for the  
use of the respective charging  
station. Public AC charging stations  
192  
Driving and operating  
4. If necessary, plug in the plug of  
the charging cable into the  
corresponding port of the external  
power source.  
9 Warning  
Make sure that the charging port  
flap is closed.  
Do not leave the charging cable  
connected to the domestic  
electrical outlet.  
Charging cable 3 194.  
5. If necessary, remove the  
protective cover from the vehicle  
plug of the charging cable.  
1. Shift into P and switch off the  
vehicle.  
The start of charging is indicated by  
the green flashing of the status  
indicator at the charging port and at  
the control box of the charging cable  
if available.  
6. Plug in the vehicle plug of the  
charging cable into the charging  
port of the vehicle.  
2. Push the charging port flap to  
release it.  
Charging status 3 193.  
3. If necessary, take the charging  
cable out of the load  
compartment.  
Driving and operating  
193  
Once charging, the vehicle plug will  
be locked to the charging port and  
cannot be disconnected while  
charging is active. - indicator  
illuminates.  
Vehicle personalisation 3 90.  
2. Disconnect the vehicle plug of the  
charging cable from the charging  
port within 30 seconds after  
unlocking.  
3. Close the charging port flap by  
pressing firmly in the centre to  
latch properly.  
Stop charging  
The high voltage battery is fully  
charged if the status indicator on the  
charging port permanently illuminates  
green.  
1. Unlock the vehicle before  
removing the vehicle plug from  
the charging port.  
Charging types 3 187  
Cancelling the charging process  
Notice  
At public charging stations, the  
cancelling and subsequent  
resuming of the charging process  
may cause additional costs.  
4. Disconnect the charging cable  
from the external power source.  
5. If necessary, store the charging  
cable in the load compartment.  
While the charging cable is plugged  
into the vehicle, the vehicle cannot be  
driven.  
If the vehicle is already unlocked,  
lock the vehicle and unlock it  
again.  
Once the charging process has  
started, only the driver's door can be  
unlocked without cancelling the  
charging process. Therefore,  
activate the driver's door only  
function in the vehicle  
Programmable charging  
By default, charging starts as soon as  
the charging cable is connected to the  
charging port of the vehicle. It is also  
possible to schedule charging using  
the Info Display.  
personalisation.  
Press < on the remote control to  
cancel the charging process at any  
time.  
Press < twice to cancel the charging  
process at any time if the function  
driver's door only is activated in the  
vehicle personalisation.  
Programmable charging is only  
possible when charging at a domestic  
electrical outlet / Green'Up socket or  
a wall box.  
Programmable charging is also  
available via the MyVauxhall App.  
Central locking system 3 9.  
194  
Driving and operating  
Notice  
5. Define the number of hours and  
minutes after which the charging  
process starts.  
6. Touch OK.  
7. Plug in the vehicle.  
Charging status  
On vehicles without integrated  
navigation system, programmable  
charging can only be used via the  
MyVauxhall App.  
If the vehicle is plugged in and the  
ignition is switched off, the charging  
status indicator indicates the  
following:  
1. Press ?.  
8. Within one minute, press b to  
Illuminates white: welcome  
lighting when charging port flap is  
opened  
activate programmable charging.  
9. Depending on version, lock the  
vehicle.  
Illuminates green: charging  
The status indicator illuminates blue  
indicating that programmable  
charging is active.  
Charging 3 190.  
Charging status 3 194.  
complete  
Flashes green: charging in  
process  
Illuminates blue: programmable  
charging active  
2. Touch a.  
3. Select Charging.  
4. Touch b.  
Illuminates red: malfunction