2025-2026 Volvo Xc70 SUV Infotainment system User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Infotainment system for Your Volvo Xc70 SUV Third Generation (2025-2026)

05 Infotainment system
General information on infotainment
05
222
* Option/accessory, for more information, see Introduction.
General
The infotainment system in your car has one of
the following four levels:
Performance
•
5" TV screen TFT
•
Steering wheel keypad* without thumb-
wheel
•
AM/FM radio
•
CD
•
AUX input
•
6 speakers
•
4x20W amplifier
High Performance
•
5" TV screen TFT
•
Steering wheel keypad* with thumbwheel
•
AM/FM radio
•
CD
•
AUX and USB input (for e.g. iPod
)
•
Bluetooth
handsfree/streaming audio
•
8 speakers
•
4x40W amplifier
High Performance Multimedia
•
7" TV screen TFT
•
Steering wheel keypad* with thumbwheel
•
AM/FM radio
•
CD/DVD
•
AUX and USB input (for e.g. iPod
)
•
Bluetooth
handsfree/streaming audio
•
8 speakers
•
4x40W amplifier
Premium Sound Multimedia
•
7" TV screen TFT
•
Steering wheel keypad* with thumbwheel
•
AM/FM radio
•
CD/DVD
•
AUX and USB input (for e.g. iPod
)
•
Bluetooth
handsfree/streaming audio
•
12 speakers
•
5x130W amplifier
Dolby, Pro Logic
Made under license from Dolby Laboratories.
Dolby, Pro Logic and the double-D symbol are
trademarks of Dolby Laboratories.
Audyssey MultEQ
1
The Audyssey MultEQ system has been used
in the development and tuning of the sound to
ensure a world-class sound experience.
Other
If the Infotainment System is active when the
engine is switched off then it is automatically
activated the next time the key is inserted into
position I or higher, and it continues with the
same source (e.g. radio) as before the engine
was switched off (the driver's door must be
closed on cars with Keyless systems*).
The infotainment system can be used for 15
minutes at a time without the remote control
1
Only applies to Premium Sound Multimedia.
05 Infotainment system
General information on infotainment
05
223
key being in the ignition switch by pressing the
On/Off button.
While the engine is being started the infotain-
ment system is switched off temporarily and
continues once the engine has started.
NOTE
Avoid using the Infotainment system when
the engine is switched off as this loads the
battery.
05 Infotainment system
Quick start
05
224
* Option/accessory, for more information, see Introduction.
Overview, Infotainment
AUX and USB
1
inputs for external audio
sources (e.g. iPod
)
Steering wheel keypad*
Centre console control panel
TV screen. The TV screen is available in
two sizes, 5" (applies to Performance and
High Performance) and 7" (applies to High
Performance Multimedia and Premium
Sound Multimedia). The manual shows the
7" TV screen.
Rear control panel with headphones
socket*
A/V-AUX input*
Operating the system
Short press starts the system and long
press switches off. Briefly press to mute
the sound (MUTE) or restore the sound if it
had been switched off.
Select a source by pressing one of the but-
tons (e.g. RADIO, MEDIA etc.). Press
repeatedly in order to scroll down among
the options on the TV screen (e.g.
FM1),
release and wait a second and the selec-
tion is accepted automatically. Alterna-
tively, it is possible to turn TUNE and con-
firm with OK/MENU.
TUNE - turn to fast-scroll among disc
tracks/folders, radio and TV* stations,
phone contacts* or navigate through
options on the TV screen (e.g.
FM1, Disc).
Source buttons
Control panel with buttons for source selection.
RADIO - Select, for example, AM, FM1,
FM2, DAB1*, DAB2*
MEDIA - Select, for example, Disc, USB*,
iPod, AUX, Bluetooth*, TV*.
TEL - Bluetooth
handsfree*
MY CAR - See page 146.
1
USB only applies to High Performance, High Performance Multimedia and Premium Sound Multimedia.
05 Infotainment system
Quick start
05
``
* Option/accessory, for more information, see Introduction.
225
Basic functions, Infotainment
Centre console with controls for basic functions.
SOUND - leads to the audio settings menu
(bass, treble, etc.). For more information,
see page 229.
VOL - turn to raise or lower the volume.
- short press starts the system and
long press switches off. Briefly press to
mute the sound (MUTE) or restore the
sound if it had been switched off.
Preset buttons, input of numbers and let-
ters.
TUNE - turn to fast-scroll among disc
tracks/folders, radio and TV* stations,
phone contacts* or navigate through
options on the TV screen.
OK/MENU - accepts selections in menus.
Lead to submenus in selected source (e.g.
RADIO or MEDIA).
EXIT - leads up in the menu system, inter-
rupts the current function, rejects calls and
deletes input characters. One long press
leads to the highest menu level (parent
view), see page 226.
INFO - press the button to see more infor-
mation about a function, song, etc. For
more information, see page 229
FAV - shortcut to a favourite setting. The
button can be programmed for a com-
monly used function in AM, FM, etc. For
more information, see page 229.
Views in the TV screen
General information about views in the
TV screen
The system contains four different types of
views. A top-level menu, so-called Parent view,
common to all sources, see page 226. For
each source there are three different basic
types of views:
•
Normal view - normal mode for the source
•
Quick view - fast mode when TUNE is
turned, e.g. for changing disc tracks, radio
station, etc.
•
Menu view - for menu navigation
The views have different appearances depend-
ing on the source, in-car equipment, settings,
etc.
Example of normal view (Radio).
Example of menu view (Bluetooth
handsfree).
05 Infotainment system
Quick start
05
226
* Option/accessory, for more information, see Introduction.
Parent view
Example of parent view (Radio).
Sources (e.g. RADIO, MEDIA, etc.), see
table.
Source menu, e.g. (FM1, DISC, etc.).
A long press on EXIT on the steering wheel
keypad* leads to the highest menu level, called
parent view (see illustration above). The func-
tion is a quick way to choose or change the
source (e.g.
RADIO, MEDIA etc.) directly from
the steering wheel keypad* without taking your
hands off the steering wheel. The function is
also available from the control panel buttons in
the centre console.
•
Select source (1) by turning the thumb-
wheel on the steering wheel keypad*, press
the thumbwheel to confirm the selection.
•
Turn the thumbwheel to one of the options
(2) on the TV screen (e.g.
FM1), press the
thumbwheel to confirm the selection.
This then leads to the desired source (e.g.
RADIO/FM1).
A long press on EXIT leads back.
NAV - Volvo's navigation system
(RTI)*
RADIO – Radio
MEDIA – Media
TEL – Bluetooth
handsfree*
MY CAR - Car settings
CAM - Park Assist Camera*
Steering wheel keypad*
The keypad is available in three different ver-
sions depending on the options and the equip-
ment level of the car.
Keypad without thumbwheel
Short presses scroll between disc tracks
or scan for the next available radio sta-
tion
2
. Long presses are used to fast for-
ward and rewind disc tracks.
Volume
2
Does not apply to DAB.
05 Infotainment system
Quick start
05
``
* Option/accessory, for more information, see Introduction.
227
Keypad with thumbwheel
Short presses scroll between disc tracks
or preset radio stations
2
. Long presses
are used to fast forward and rewind disc
tracks.
Volume
EXIT – leads up in the menu system. Inter-
rupt current function, end/refuse phone
calls, clear entered characters. One long
press leads to the highest menu level
(parent view), see page 226.
Thumbwheel - turn up/down to scroll up
and down in the menu system. One press
on the thumbwheel leads to the menu
(equivalent to MENU), or confirms a selec-
tion (OK) in the menu system, and accepts
phone calls.
MUTE - switches off the sound
Keypad with thumbwheel, for voice
recognition
3
Short presses scroll between disc tracks
or preset radio stations
2
. Long presses
are used to fast forward and rewind disc
tracks.
Volume
EXIT – leads up in the menu system. Inter-
rupt current function, end/refuse phone
calls, clear entered characters. One long
press leads to the highest menu level
(parent view), see page 226.
Thumbwheel - turn up/down to scroll up
and down in the menu system. One press
on the thumbwheel leads to the menu
(equivalent to MENU), or confirms a selec-
tion (OK) in the menu system, and accepts
phone calls.
Voice recognition (for Bluetooth
-con-
nected mobile phone and navigation sys-
tem*)
Rear control panel with headphones
socket*
Headphones with an impedance of
16-32 ohm and sensitivity of 102 dB or higher
are recommended for best sound reproduc-
tion.
2
Does not apply to DAB.
3
Only cars with navigation.
05 Infotainment system
Quick start
05
228
* Option/accessory, for more information, see Introduction.
VOLUME – Volume, left and right.
Scroll/search forward and backward.
MODE - Select between AM, FM1, FM2,
DAB1*, DAB2*, Disc, USB*, iPod*,
Bluetooth*, AUX, TV* and On/Off. For
connection via USB* or AUX, see
page 243 or via Bluetooth
*, see
page 247.
Headphones sockets (3.5 mm).
Activate/deactivate
The control panel is activated with MODE.
Deactivation is possible via a long press on
MODE or when the engine is switched off.
Scroll/search forward and backward
Pressing (2) scrolls between disc tracks/audio
files or seeks the next available radio station.
Limitations
NOTE
The audio source (e.g. FM1, AM, Disc etc.)
being played back through the speakers
cannot be controlled from the rear control
panel.
NOTE
In order that an audio source can be
selected with MODE and listened to it is
required that the audio source is available
and connected in the car.
05 Infotainment system
General infotainment functions
05
``
* Option/accessory, for more information, see Introduction.
229
FAV - store a preset
The FAV button can be used to store functions
that are used frequently so that the function
can be started simply by pressing FAV. You
can select a favourite (e.g.
Equalizer) for each
function as follows:
In RADIO mode:
•
AM
•
FM1/FM2
•
DAB1*/DAB2*
In MEDIA mode:
•
DISC
•
USB*
•
iPod*
•
Bluetooth*
•
AUX
•
TV*
It is also possible to select and store a favourite
for TEL*, MY CAR, CAM* and NAV*. Favour-
ites can also be selected and stored under MY
CAR. For more information on the menu sys-
tem MY CAR, see page 146.
To store a function in the FAV button:
1. Select an infotainment source (e.g.
RADIO, MEDIA etc.).
2.
Select a wavelength or source (
AM, Disc,
etc.).
3.
Press and hold the FAV button until the
"favourites menu" is shown.
4.
Turn TUNE to select an option from the list
and press OK/MENU to save.
>
When the source (e.g. RADIO, MEDIA
etc.) is active the stored function is
available by means of a short press on
FAV.
INFO - shows additional information
In some cases there is more information avail-
able (on a radio station, song, artist, etc.) than
can be shown in the TV screen. To see more
information, press the INFO button.
General audio settings
Press SOUND to access the audio settings
menu (
Bass, Treble, etc.). Scroll forward with
SOUND or OK/MENU to your selection (e.g.
Treble).
Adjust the setting by turning TUNE and save
the setting with OK/MENU.
Continue pressing SOUND or OK/MENU to
access other options:
05 Infotainment system
General infotainment functions
05
230
* Option/accessory, for more information, see Introduction.
•
Surround
1
- Can be set to the On/Off posi-
tion. When On is selected, the system
selects the setting for optimal sound repro-
duction. Normally DPLII and
then
appear in the TV screen. If the recording is
made with Dolby Digital technology then
playback will take place with this setting,
then appears in the TV screen.
When Off is selected, 3-channel stereo is
available.
•
Bass - Bass level.
•
Treble - Treble level.
•
Fader – Balance between the front and
rear speakers.
•
Balance – Balance between the left and
right-hand speakers.
•
Subwoofer*
1
- Bass speaker level.
•
DPL II center level3 channel center
level
1
- Volume for centre speaker.
•
DPL II surround level
1, 2
– Level for sur-
round.
Advanced audio settings
Equalizer
3
The volume level can be adjusted separately
for different wavelengths.
1.
Press OK/MENU to access
Audio
settings
and select Equalizer.
2.
Select wavelength by turning TUNE and
confirm with OK/MENU.
3.
Adjust the volume level by turning TUNE
and confirm with OK/MENU. Continue in
the same way with other wavelengths.
4. When you are finished with the settings,
turn TUNE
OK and confirm by pressing
OK/MENU or EXIT.
For general information on menu navigation
and menu structures, see page 275.
Sound stage
1
The sound experience can be optimised for the
driver's seat, both front seats or the rear seat.
If there are passengers in both the front and
rear seats then the option recommended is;
both front seats. The options can be selected
under
Audio settings Sound stage.
For general information on menu navigation
and menu structures, see page 275.
Audio volume and automatic volume
control
The audio system compensates for disrupting
noises in the passenger compartment by
increasing the volume in relation to the speed
of the car. The compensation level can be set
to low, medium, high or off. Select the level
under
Audio settings Volume
compensation
.
For general information on menu navigation
and menu structures, see page 275.
External audio source audio volume
If an external audio source (e.g. an MP3 player
or iPod
) is connected to the AUX input then
the audio source that is connected can have a
different volume than the audio system's inter-
nal volume (e.g. radio). Correct this by adjust-
ing the volume of the input:
1.
Press the MEDIA button and turn TUNE to
AUX and wait a few seconds or press OK/
MENU.
1
Only Premium Sound Multimedia.
2
Only when Surround is activated.
3
Not Performance.
05 Infotainment system
General infotainment functions
05
231
2.
Press OK/MENU and then turn TUNE to
AUX input volume. Confirm with OK/
MENU.
3.
Turn TUNE to adjust the volume for the
AUX input.
NOTE
If the external audio source's volume is too
high or too low, the quality of the sound may
deteriorate. The audio quality may also be
impaired if the player is charged while the
infotainment system is in AUX mode. In
which case, avoid charging the player via
the 12 V socket.
Optimum sound reproduction
The audio system is pre-calibrated for opti-
mum sound reproduction by means of digital
signal processing.
This calibration takes into account loudspeak-
ers, amplifiers, passenger compartment
acoustics, listener position etc. for each com-
bination of car model and audio system.
There is a also a dynamic calibration that takes
into account the position of the volume control,
radio reception and vehicle speed.
The controls explained in these operating
instructions, e.g.
Bass, Treble and
Equalizer, are only intended for the user to be
able to adapt the sound reproduction accord-
ing to personal taste.
05 Infotainment system
Radio
05
232
* Option/accessory, for more information, see Introduction.
Radio functions, general
Centre console, controls for radio functions.
RADIO button for selecting the wavelength
(AM, FM1, FM2, DAB1*, DAB2*).
Station presets (0-9)
Select the desired frequency/station or
navigate in the radio menu by turning
TUNE.
Confirm your selection or go to the radio
menu by pressing OK/MENU.
Hold in the button for next/previous avail-
able station. Short press for preset.
NOTE
If the car is equipped with a steering wheel
keypad* and/or remote control* then in
many cases these can be used instead of
the buttons in the centre console. For a
description of the buttons in the steering
wheel, see page 226. For a description of
the remote control, see page 252.
Menus
The menus inRADIO are controlled from the
centre console and the steering wheel key-
pad*. For general information on menu naviga-
tion and menu structures, see page 275.
Radio AM/FM
Tuning
Automatic tuning
1.
Repeatedly press on the RADIO button
until the desired wavelength (
AM, FM1
etc.) is shown, release and wait a second
or press OK/MENU.
2.
Hold in
/ in the centre console (or
in the steering wheel keypad*). The radio
searches for the next/previous available
station.
Station list
1
The radio automatically compiles a list of the
strongest FM stations whose signals it is cur-
rently receiving. This enables you to find a sta-
tion when you drive into an area where you do
not know the radio stations and their frequen-
cies.
To go to the list and select a station:
1.
Select the desired wavelength (
FM1 or
FM2).
2.
Turn TUNE one step in either direction.
This displays the list of all stations in the
area. The currently tuned station is indi-
cated with enlarged text in the list.
3.
Turn TUNE again in either direction to
select a station from the list.
1
Only applies to FM1/FM2.
05 Infotainment system
Radio
05
233
NOTE
•
The list only shows the frequencies of
stations that are currently being
received, not a complete list of all radio
frequencies on the selected wave-
length.
•
If the signal from the currently received
station is weak, this may prevent the
radio from updating the station list. If
this occurs, press the
button
(while the station list is shown in the dis-
play screen) in order to change to man-
ual tuning and set a frequency. If the
station list is no longer shown, turn
TUNE one step in either direction to
show the list again, and press
to
switch.
The list disappears from the TV screen after a
few seconds.
If the station list is no longer shown, turn
TUNE one step in either direction and press the
button in the centre console to change
to manual tuning (or to return from manual tun-
ing to the function for "Station list").
Manual tuning
The preset from the factory is that the radio
shows the station list of the strongest stations
in the area when you turn TUNE (see the sec-
tion "Station list", page 232). When the station
list is shown, press the
button in the cen-
tre console to change to manual tuning. This
allows you to select a frequency from the list of
all available radio frequencies in the selected
wavelength. In other words, if turn TUNE one
step in a manual search the frequency is
changed from e.g. 93.3 to 93.4 MHz, etc.
To manually select a station:
1.
Repeatedly press on the RADIO button
until the desired wavelength (
AM, FM1
etc.) is shown, release and wait a second
or press OK/MENU.
2.
Turn TUNE to select a frequency.
NOTE
The preset from the factory is that the radio
automatically searches for the stations in
the area where you are driving (see previous
section "Station list" above).
But if you have changed over to manual tun-
ing (by pressing the
button in the cen-
tre console when the station list was
shown), then the radio remains set in the
function for manual tuning the next time you
switch on the radio. To change back to the
function for "Station list", turn TUNE one
step (to show the complete list of stations)
and press the button
.
Note that if you press
when the sta-
tion list is not shown then INFO is activated.
For more information on this function, see
page 229.
Preset
10 presets can be stored per wavelength
(
AM, FM1 etc.).
The stored presets are selected using the pre-
set buttons.
1. Tune into a station (see "Tuning", page
232).
2. Hold in one of the preset buttons for a few
seconds, the sound disappears during this
05 Infotainment system
Radio
05
234
time and returns when the station is stored.
The preset button can now be used.
A list of pre-selected channels can be shown
2
in the TV screen. The function is activated/
deactivated in FM/AM mode under
FM menu
Show presets or AM menu Show
presets.
Scan wavelength
The function automatically searches the cur-
rent wavelength for strong stations. When a
station is found, it is played for approx. 8 sec-
onds before scanning is resumed. When a sta-
tion is playing back it can be saved as a preset
in the usual way, see the section "Pre-
set" above.
– To start scanning go in FM/AM mode to
FM menu Scan or AM menu Scan.
NOTE
Scanning stops if a station is saved.
RDS functions
RDS (Radio Data System) links FM transmitters
into a network. An FM transmitter in such a
network sends information that gives an RDS
radio the following functions:
•
Automatically switches to a stronger trans-
mitter if reception in the area is poor.
•
Searches for programme type, such as
traffic information or news.
•
Receives text information on current radio
programme.
NOTE
Some radio stations do not use RDS or only
some if its functionality.
If a required programme type is located the
radio can switch stations interrupting the audio
source currently in use. For example, if the CD
player is in use, it is paused. The interrupting
transmission is played at a preset volume, see
page 236. The radio returns to the previous
audio source and volume when the set pro-
gramme type is no longer broadcast.
The programme functions alarm (
ALARM!),
traffic information (
TP), news (NEWS), and pro-
gramme types (
PTY) interrupt one another in
order of priority, where alarm has the highest
priority and programme types has the lowest.
For additional settings of programming inter-
ruptions (
EON Distant and EON Local), see
the section "Enhanced Other Networks –
EON" below. Press EXIT to return to the inter-
rupted audio source, press the OK/MENU to
clear the message.
Alarm
This function is used to warn of serious acci-
dents and catastrophes. The alarm cannot be
temporarily interrupted or deactivated. The
message
ALARM! appears on the TV screen
when an alarm message is transmitted.
Traffic information – TP
This function allows traffic information sent
within a set station's RDS network to break
through. The
TP symbol indicates that the
function is activated. If the preset station can
send traffic information then this is shown by
TP glowing brightly in the TV screen, otherwise
TP will be grey.
–
Activate/deactivate in FM mode under FM
menu
TP.
Enhanced Other Networks – EON
This function is useful in urban areas with many
regional radio stations. It allows the distance
between the car and the radio station trans-
mitter to determine when programme functions
should interrupt the current audio source.
2
Only applies to High Performance Multimedia and Premium Sound Multimedia.
05 Infotainment system
Radio
05
``
235
– Activate/deactivate in FM mode by select-
ing one of the options under
FM menu
Advanced settings EON:
•
Local – interrupts only if the radio station
transmitter is close.
•
Distant
3
– interrupts if the station trans-
mitter is far away, even if there is a lot of
static.
TP from selected station/all stations
The radio can only interrupt for traffic informa-
tion from the selected station or all stations
within the RDS network.
–
Go in FM mode to FM menu Advanced
settings
Set TP favourite to change.
News
This function allows news broadcasts sent
within a set station's RDS network to break
through. The
NEWS symbol indicates that the
function is active.
–
Activate/deactivate in FM mode under FM
menu News settings News.
News from selected station/all stations
The radio can only interrupt for news from the
selected station or all stations in the RDS net-
work.
–
Go in FM mode to FM menu
News
settings
Set news favourite to change.
Programme types – PTY
The PTY function can be used to select one or
more programme types, such as pop music
and serious classic. The PTY symbol indicates
that the function is active. This function allows
programme types broadcast within a set sta-
tion's RDS network to break through.
1. Activate in FM mode by first selecting the
programme types under
FM menu
Advanced settings PTY settings
Select PTY.
2. Then the PTY function must be activated
under
FM menu Advanced settings
PTY settings Receive traffic
bulletins from other networks.
An indicator is shown in the TV screen when
PTY is activated.
Deactivation of the PTY function is performed
in FM mode under
FM menu Advanced
settings
PTY settings Receive traffic
bulletins from other networks. Selected pro-
gramme types (PTY) are not reset.
Resetting and removing PTY are performed
under
FM menu
Advanced settings
PTY settings Select PTY Clear all.
PTY search
This function searches the entire wavelength
for the selected programme type.
1. In FM mode select one or more PTY under
FM menu Advanced settings PTY
settings Select PTY.
2.
Go to
FM menu Advanced settings
PTY settings Seek PTY.
To finish searching, press EXIT.
– To continue searching for another broad-
cast of the selected programme types,
press on
or .
Display of programme type
The programme type of the current station can
be shown on the TV screen.
–
Activate/deactivate in FM mode under FM
menu Advanced settings PTY
settings
Show PTY text.
3
Factory settings.
05 Infotainment system
Radio
05
236
* Option/accessory, for more information, see Introduction.
Radio text
Some RDS stations transmit information on
programme content, artists, etc. This informa-
tion can be shown on the TV screen.
–
Activate/deactivate in FM mode under FM
menu Show radio text.
Automatic frequency update – AF
The function selects the strongest transmitter
for the set station. In order to find a strong
transmitter the function may, in exceptional
cases, need to search the entire FM wave-
length.
–
Activate/deactivate in FM mode under FM
menu Advanced settings
Alternative frequency.
Regional radio programmes – REG
This function causes the radio to continue with
a regional transmitter even if its signal strength
is low. The symbol
REG shows that the func-
tion is active.
–
Activate/deactivate in FM mode under FM
menu Advanced settings REG.
Resetting RDS functions
All radio settings can be reset to the original
factory settings.
– The reset is carried out in FM mode under
FM menu
Advanced settings
Reset all FM settings.
Volume control, programme types
The interrupting programme types, e.g.
NEWS or TP, are heard at the volume selected
for each respective programme type. If the vol-
ume level is adjusted during the programme
interruption, the new level is saved until the
next programme interruption.
Radio system - DAB*
General
DAB (Digital Audio Broadcasting) is a digital
broadcasting system for radio.
NOTE
This system does not support DAB+.
NOTE
Coverage for DAB is not available in all loca-
tions. If there is no coverage then the mes-
sage
No reception is shown in the display
screen.
Service and Ensemble
•
Service - Channel, radio channel (only
audio services are supported by the sys-
tem).
•
Ensemble - A collection of radio channels
on the same frequency.
Storing channel groups (Ensemble learn)
When the vehicle is moved to a new broad-
casting area, programming of existing channel
groups in the area may be necessary.
Programming of channel groups creates an
updated list of all available channel groups.
The list is not updated automatically.
Programming is carried out in the menu system
in DAB mode under
DAB menu
Ensemble
learn. Programming can also take place as fol-
lows:
1.
Turn TUNE one step in either direction.
>
Ensemble learn is shown in the list of
available channel groups.
2.
Press OK/MENU.
> New programming is started.
Programming can be cancelled with EXIT.
If can take up to a minute to program a channel
group if both
Band III and LBand are selected.
For more information on wavelength, see
page 238.
05 Infotainment system
Radio
05
237
Navigation in channel group list
(Ensemble)
To navigate in and access the channel group
list turn TUNE. The name of the Ensemble is
shown in the upper part of the TV screen. When
scrolling to the new Ensemble the name
changes to the new one. A thick grey line sep-
arates the two channel groups from each other.
•
Service - Shows channels irrespective of
the channel group to which they are allo-
cated. The list can also be filtered using the
selection of programme type (
PTY
filtering
), see below.
Scanning
The function automatically searches the cur-
rent wavelength for strong stations. When a
station is found, it is played for approx. 8 sec-
onds before scanning is resumed. When a sta-
tion is playing back it is saved as a preset in the
usual way. For more information on presets,
see "Preset" below.
–
Go in DAB mode to DAB menu Scan to
start scanning.
NOTE
Scanning stops if a station is saved.
Scanning can also be selected in DAB-PTY
mode. In which case only channels of the pre-
selected programme type are played.
Programme type (PTY)
Various types of radio programmes can be
selected using the programme type function.
There are a number of different programme
types which also include different programme
categories. After selecting a programme type,
navigation only takes place within the channels
that are broadcasting that type.
Programme type is selected in DAB mode
under
DAB menu
PTY filtering. Exit this
mode as follows:
–
Press EXIT.
> An indicator is shown in the TV screen
when PTY is activated.
In certain cases DAB radio will exit PTY mode
when DAB to DAB linking (see below) is imple-
mented.
Preset
10 station presets can be stored per wave-
length. DAB has 2 memories for presets:
DAB1 and DAB2. Storing of presets is per-
formed in the usual way, for more information
see page 233. The stored presets are selected
using the preset buttons.
A preset contains one channel but no sub-
channels. If a subchannel is being played and
a preset is saved then only the main channel is
registered. This is because subchannels are
temporary. At the next attempt to retrieve the
preset, the channel which contained the sub-
channel will be played. The preset is not
dependent on the channel list.
A list of pre-selected channels can be shown
4
in the TV screen. The function is activated/
deactivated in DAB mode under
DAB menu
Show presets.
NOTE
The audio system's DAB system does not
support all functions available in the DAB
standard.
Radio text
Some radio stations transmit information on
programme content, artists, etc. This informa-
tion is shown on the TV screen.
The function is deactivated/activated in DAB
mode under
DAB menu Show radio text.
4
Only applies to High Performance Multimedia and Premium Sound Multimedia
05 Infotainment system
Radio
05
238
NOTE
Only one of the functions "Show radio
text
" and "Show presets" can be acti-
vated at a time. If one of them is activated
when the other is already activated, then the
previously activated function is deactivated
automatically. Both functions can be deac-
tivated.
Advanced settings
DAB to DAB link
It is possible to exit a channel with poor or no
reception to the same channel in another chan-
nel group with better reception. There may be
a certain delay when changing channel group.
There may be a period of silence between the
current channel no longer being available to the
new channel becoming available.
The function can be activated/deactivated in
DAB mode under
DAB menu
Advanced
settings
DAB linking.
Wavelength
DAB can be transmitted on two
5
wavelengths:
•
Band III - covers areas outside big cities
•
LBand - mainly in large cities
By selecting for example
Band III on its own,
channel programming takes place more
quickly than if both
Band III and LBand have
been selected. It is not certain that all channel
groups will be found. Wavelength selection
does not affect the stored memories.
Wavelengths can be deactivated/activated in
DAB mode under
DAB menu Advanced
settings
DAB band.
Subchannel
Secondary components are usually named
subchannels. These are temporary and can
contain e.g. translations of the main pro-
gramme into other languages.
If one or more subchannels are broadcast then
the
> symbol is shown to the left of the channel
name in the TV screen. A subchannel is indi-
cated by the
- symbol appearing to the left of
the channel name in the TV screen.
Subchannels can only be accessed on the
selected main channel and not on any other
channel without selecting it.
Display of subchannels can be deactivated/
activated in DAB mode under
DAB menu
Advanced settings Sub channels
Programme type text
Some radio stations broadcast information
about programme type and programme cate-
gory. This information is shown on the TV
screen.
The function is activated/deactivated in DAB
mode under
DAB menu
Advanced
settings
Show PTY text.
Resetting the DAB settings
All DAB settings can be reset to the original
factory settings.
– The reset is carried out in DAB mode under
DAB menu Advanced settings
Reset all DAB settings.
5
Not all areas/countries use both wavelengths.
05 Infotainment system
Media player
05
* Option/accessory, for more information, see Introduction.
239
CD/DVD
1
functions
Centre console control panel.
Disc insert and eject slot
MEDIA key
Disc eject
Input of numbers and letters.
Select the disc tracks/folders, or navigate
through menu options by turning TUNE.
Confirm your selection or go to the menu
for the selected media source by pressing
OK/MENU.
Fast forward/reverse and change disc
track or chapter
2
.
The media player supports and can play the
following main types of discs and files:
•
Pre-recorded CD discs (CD Audio).
•
Burned CD discs with audio and/or video
files
1
.
•
Pre-recorded DVD video discs
1
.
•
Burned DVD discs
1
with audio and/or video
files.
For more information about the supported for-
mats, see page 242.
NOTE
If the car is equipped with a steering wheel
keypad* and/or remote control* then in
many cases these can be used instead of
the buttons in the centre console. For a
description of the buttons in the steering
wheel, see page 226. For a description of
the remote control, see page 252.
Menus
The menus inMEDIA are controlled from the
centre console and the steering wheel key-
pad*. For general information on menu naviga-
tion and menu structures, see page 275.
Starting playback of a disc
Repeatedly press on the MEDIA button until
Disc is shown, release and wait a second or
press OK/MENU. If there is a disc in the media
player then the disc starts playing back auto-
matically, otherwise
Insert disc is shown in the
TV screen. Then insert a disc, with text side up.
The disc starts to play back automatically.
If a disc with audio/video files is inserted into
the player then the disc's folder structure
needs to be loaded. Depending on the quality
of the disc and the quantity of information there
may be a certain delay before playback starts.
Disc eject
A disc remains in the ejected position for
about 12 seconds, after which it is inserted
back into the player for safety reasons.
Pause
When the volume is turned down completely
the media player is paused. When the volume
is increased, it starts again.
Playback and navigation
CD audio discs
Turn TUNE to access the disc's playlist and
navigate in the list. Use OK/MENU to confirm
the selection of the disc track and start play-
1
Only applies to High Performance Multimedia and Premium Sound Multimedia.
2
Only applies to DVD discs.
05 Infotainment system
Media player
05
240
* Option/accessory, for more information, see Introduction.
back. Press EXIT to cancel and exit the playlist.
A long press on EXIT leads to the playlist's root
level.
Disc tracks can also be changed by pressing
on
/ on the centre console or the
steering wheel keypad*.
Burned discs audio/video files
1
Turn TUNE to access the disc's playlist/folder
structure and navigate in the list/structure. Use
OK/MENU to confirm either selection of sub-
folder or start of playback of the selected
audio/video file. Press EXIT to either stop and
exit the playlist or go up (back) in the folder
structure. A long press on EXIT leads to the
playlist's root level.
Audio/video files can also be changed by
pressing
/ on the centre console or the
steering wheel keypad*.
Audio files have the symbol
, video files
1
have the symbol
and folders have the
symbol
.
When playback of a file is complete the play-
back of the other files (of the same type) in that
particular folder continues. Change
3
of folder
takes place automatically when all the files in
the current folder have been played back. The
system automatically detects and changes
setting when a disc containing only audio files
or only video files is loaded into the media
player and then plays back these files. How-
ever, the system does not change setting if a
disc containing a mixture of audio and video
files is loaded into the media player, but instead
the player continues to play back the previous
file type.
NOTE
A video film is only shown when the car is
stationary. When the car is moving at a
speed of over about 8 km/h no picture is
shown and
No visual media available
during driving
appears on the display
screen, although the audio is heard during
this time. The picture is shown again as
soon as the car's speed falls below about 6
km/h.
NOTE
Some audio files that are copy-protected by
record companies or privately copied audio
files cannot be loaded by the player.
DVD video discs
1
For playback of DVD video discs, see
page 241.
Fast forward/reverse
Hold in the buttons / to fast forward/
rewind. Audio files are fast forwarded/rewound
at one speed, while video files are fast forwar-
ded/rewound at several speeds. Repeatedly
press the buttons
/ to increase the fast
forward/rewind speed for video files. Release
the button to return to viewing at normal speed.
Music recognition, Gracenote
If the car is equipped with navigation* then
there is a hard drive in the car that contains a
database for music recognition of CD audio
discs. The database contains the most popular
songs at the moment. If the media player gets
a hit in the database then the album title and
artist name for the media are displayed, and
each track shows track title, artist and album.
If the current CD audio disc is not found in the
database then the CD text from the disc is
used. If there is no CD text on the disc then only
Track 1, Track 2 etc. is displayed.
1
Only applies to High Performance Multimedia and Premium Sound Multimedia.
3
If Repeat folder is activated then this does not take place.
05 Infotainment system
Media player
05
* Option/accessory, for more information, see Introduction.
241
Scan
4
This function plays the first ten seconds of
each disc track/audio file. To scan:
1.
Press OK/MENU
2.
Turn TUNE to
Scan
> The first 10 seconds of each disc track
or audio file are played.
3.
Cancel the scan with EXIT, the disc track
or audio file being played back will con-
tinue playing.
Random
4
This function plays the tracks in random order.
To listen to the tracks in random order:
1.
Press OK/MENU
2.
Turn TUNE to
Random
3.
Press OK/MENU to activate/deactivate
the function.
Disc tracks/audio files can be changed by
pressing
/ on the centre console or the
steering wheel keypad*.
Repeat folder
5
This function makes it possible to play files in
a folder over and over again. When the last file
has been played out, playback of the first file
starts again.
1.
Press OK/MENU
2.
Turn TUNE to
Repeat folder
3.
Press OK/MENU to activate/deactivate
the function.
Playback of DVD video discs
1
Playback
When playing back a DVD video disc a disc
menu may appear on the display screen. The
disc menu gives access to additional functions
and settings, such as selecting subtitles, lan-
guage and scene selection.
NOTE
A video film is only shown when the car is
stationary. When the car is moving at a
speed of over about 8 km/h no picture is
shown and
No visual media available
during driving
appears on the display
screen, although the audio is heard during
this time. The picture is shown again as
soon as the car's speed falls below about 6
km/h.
Navigation in the DVD video disc's menu
Navigation in the DVD video disc's menu is
performed using the number keys in the centre
console as illustrated above.
Changing chapter or title
Turn TUNE to access the list of chapters and
navigate through them (if the film is being
played back then it is paused). Press OK/
MENU to select the chapter, this also leads
back to the original position (if the film was
being played back then it is restarted). Press
EXIT to access the title list.
Titles are selected in the title list by turning
TUNE and the selection is confirmed with OK/
MENU, this also leads back to the chapter list.
4
Does not apply to DVD video discs.
5
Only applies to audio/video files on burned discs or USB.
1
Only applies to High Performance Multimedia and Premium Sound Multimedia.
05 Infotainment system
Media player
05
242
* Option/accessory, for more information, see Introduction.
Press OK/MENU to activate the selection and
return to the start position. Use EXIT to cancel
the selection and this leads back to the original
position (without any selection being made).
The chapter can also be changed by pressing
on
/ on the centre console or the
steering wheel keypad*.
Advanced settings
6
Angle
If the DVD video disc supports it, the function
can be used to choose from which camera
position a particular scene should be shown.
Go in disc mode to
Disc menu Advanced
settings
Angle.
DivX
Video On Demand
The media player can be registered in order to
play DivX VOD type files from burned discs or
USB. The code for registration can be found in
the menu system MY CAR
Settings
Information DivX® VOD code. For general
information on menus, see under MY CAR, see
page 146.
For more information visit
Picture settings
6
You can adjust the settings (when the car is
stationary) for brightness and contrast.
1.
Press OK/MENU and select
Image
settings
, confirm with OK/MENU.
2.
Turn TUNE to the adjustment option and
confirm with OK/MENU.
3.
Adjust the setting by turning TUNE and
confirm with OK/MENU.
To return to the settings list, press the OK/
MENU or EXIT.
The picture settings can be reset to factory
settings with the
Reset option.
Compatible file formats
The media player can play back a variety of file
types and is compatible with the formats in the
following table.
NOTE
Dual format, double-sided discs (DVD Plus,
CD-DVD format) are thicker than regular CD
discs and therefore playback cannot be
guaranteed and malfunction may arise.
If a CD contains a mixture of MP3 and CDDA
tracks, all MP3s will be ignored.
Audio format
A
CD audio, mp3,
wma
Audio format
B
CD audio, mp3,
wma, aac, m4a
Video format
C
CD video,
DVD video, divx, avi,
asf
A
Applies to Performance.
B
Does not apply to Performance.
C
Only applies to High Performance Multimedia and Premium
Sound Multimedia.
6
Applies to High Performance Multimedia and Premium Sound Multimedia.
05 Infotainment system
External audio source via AUX/USB* input
05
* Option/accessory, for more information, see Introduction.
243
AUX, USB
1
and external audio source
General
Connection points for external audio sources.
An external audio source, e.g. an iPod
or MP3
player, can be connected to the audio system
via any of the connections in the centre con-
sole. An audio source connected to the USB
input can then be handled
2
with the car's audio
controls. A device connected via the AUX input
cannot be controlled via the car.
There is a recess in the right-hand rear edge of
the tunnel console where cables can be routed
so that the hatch can be closed without cables
being pinched.
NOTE
If the car is equipped with a steering wheel
keypad* and/or remote control* then in
many cases these can be used instead of
the buttons in the centre console. For a
description of the buttons in the steering
wheel, see page 226. For a description of
the remote control, see page 252.
An iPod
or MP3 player with rechargeable bat-
teries is recharged (when the ignition is on or
the engine is running) if the device is plugged
into the USB connection.
To connect the audio source:
1.
Repeatedly press on MEDIA to reach the
desired audio source
USB, iPod or AUX,
release and wait a second or press OK/
MENU.
>
If USB is selected then
Connect USB is
shown in the TV screen.
2. Connect your audio source to one of the
connections in the centre console's stor-
age compartment (see previous illustra-
tion).
The text
Reading USB is shown in the TV
screen when the system is loading the storage
media's file structure. Depending on the file
structure and number of files there may be
some delay before loading is finished.
NOTE
The system supports most iPod
models
produced in 2005 or later.
NOTE
To prevent damage to the USB connection,
this is shut off if the USB connection is
short-circuited or if a connected USB unit is
taking too much power (this may happen if
the unit connected does not meet the USB
standard). The USB connection is reactiva-
ted automatically the next time the ignition
is turned on, unless the fault persists.
Menus
The menus inMEDIA are controlled from the
centre console and the steering wheel key-
pad*. For general information on menu naviga-
tion and menu structures, see page 275.
1
Applies to High Performance, High Performance Multimedia and Premium Sound Multimedia.
2
Only applies to the media source connected via the USB connection.
05 Infotainment system
External audio source via AUX/USB* input
05
244
* Option/accessory, for more information, see Introduction.
Playback and navigation
3
Turn TUNE to access the playlist/folder struc-
ture and navigate in the list/structure. Use OK/
MENU to either confirm selection of subfolder
or start of playback of the selected audio/video
file. Press EXIT to either stop and exit the play-
list or go up (back) in the folder structure. A long
press on EXIT leads to the playlist's root level.
Audio/video files can also be changed by
pressing
/ on the centre console or the
steering wheel keypad*.
Audio files have the symbol
, video files
4
have the symbol
and folders have the
symbol
.
When playback of a file is complete the play-
back of the other files (of the same type) in that
particular folder continues. Change
5
of folder
takes place automatically when all the files in
the current folder have been played back. The
system automatically detects and changes
setting when a device containing only audio
files or only video files is connected to the USB
port and then it plays back these files. How-
ever, the system does not change setting if a
device containing a mixture of audio and video
files is connected to the USB port, but instead
the player continues to play back the previous
file type.
Fast forward/reverse
3
See page 240.
Scan
3
See page 241.
Random
3
See page 241.
Search function
3
The keypad on the control panel in the centre
console can be used to find a filename in the
current folder.
The search function is accessed either by turn-
ing TUNE (to access the folder structure) or by
pressing one of the letter keys. As a letter or
character in a search string is entered you get
closer to your search target.
Start playback of a file by pressing OK/
MENU.
Repeat folder
6
See page 241.
Audio sources
USB memory
To facilitate the use of a USB memory stick,
only store music files on it. It takes a lot longer
for the system to load storage media that con-
tains anything other than compatible music
files.
NOTE
The system supports mobile media compli-
ant with USB 2.0 and the FAT32 file system
and can handle 1000 folders with a maxi-
mum of 254 subfolders/files in every folder.
The top level, which can handle up to 1000
subfolders/files, is an exception to this.
NOTE
When using a longer model USB memory
stick the use of a USB adapter cable is rec-
ommended. This is to avoid mechanical
wear to the USB input and the connected
USB memory stick.
USB hub
It is possible to connect a USB hub to the USB
connection and thereby connect multiple USB
devices simultaneously. Selection of USB
3
Only applies to USB and iPod
.
4
Applies to High Performance Multimedia and Premium Sound Multimedia.
5
If Repeat folder is activated then this does not take place.
6
Only applies to USB.
05 Infotainment system
External audio source via AUX/USB* input
05
* Option/accessory, for more information, see Introduction.
245
device is made in
USB mode under USB menu
Select USB device.
MP3 player
Many MP3 players have their own file systems
that are not supported by the audio system. For
use in the system, an MP3 player must be set
in
USB Removable device/Mass Storage
Device
mode.
iPod
An iPod
is charged and supplied with power
by the USB connection* via the player's con-
nection cable.
NOTE
The system only supports the playback of
audio files from iPod
.
NOTE
When an iPod
is used as audio source, the
car's infotainment system has a menu
structure that is similar to the iPod
player's
own menu structure.
Compatible file formats via the USB
connection
Audio and video files in the following table are
supported by the system for playback via the
USB connection.
Audio format mp3, wma, aac,
m4a
Video format
A
divx, avi, asf
A
Only applies to High Performance Multimedia and Premium
Sound Multimedia.
05 Infotainment system
Media Bluetooth
*
05
246
* Option/accessory, for more information, see Introduction.
Streaming audio
General
The car's media player is equipped with
Bluetooth
1
and can wirelessly play streaming
audio files from external devices with
Bluetooth
, such as mobile phones and PDAs.
Navigation and control of the sound can be
carried out via the centre console buttons or via
the steering wheel keypad*. In some external
devices it is also possible to change tracks
from the device.
To play back the audio the car's media player
must first be set in
Bluetooth mode.
NOTE
The Bluetooth
media player must support
the Audio/Video Remote Control Profile
(AVRCP) and Advanced Audio Distribution
Profile (A2DP). The player should use
AVRCP version 1.3, A2DP 1.2. Otherwise
some functions may not work.
Not all mobile phones and external media
players available in the market are fully com-
patible with the Bluetooth
function in the
car's media player. Volvo recommends that
you contact an authorised Volvo dealer or
visit for information on
compatible phones and external media
players.
NOTE
The car's media player can only play the
audio files via the Bluetooth
function.
Overview
Centre console control panel.
VOL – volume
MEDIA key
Navigate in the menu by turning TUNE.
Confirm your selection or go to the menu
by pressing OK/MENU.
EXIT - leads up in the menu system, stops
the function in progress.
Short presses are used to scroll between
audio files. Long presses are used to fast
forward and rewind audio files.
1
Applies to High Performance, High Performance Multimedia and Premium Sound Multimedia.
05 Infotainment system
Media Bluetooth
*
05
* Option/accessory, for more information, see Introduction.
247
NOTE
If the car is equipped with a steering wheel
keypad* and/or remote control* then in
many cases these can be used instead of
the buttons in the centre console. For a
description of the buttons in the steering
wheel, see page 226. For a description of
the remote control, see page 252.
Menus
The menus inMEDIA are controlled from the
centre console and the steering wheel key-
pad*. For general information on menu naviga-
tion and menu structures, see page 275.
Pair and connect external device
The connection of an external device takes
place in different ways depending on whether
or not it has been previously paired. A maxi-
mum of 10 external devices can be paired.
Pairing takes place once per external device.
To connect a device for the first time, follow the
instructions below:
1.
Repeatedly press on MEDIA until
Bluetooth is shown, release and wait a
second or press OK/MENU.
2.
Press OK/MENU.
3.
When
Add device is shown, press OK/
MENU.
4. Check that the external device is searcha-
ble/visible via Bluetooth
, see the manual
for the external device.
5.
Press OK/MENU.
> The infotainment system searches for
external devices in the vicinity. The
search may take a little while. The devi-
ces detected are specified with their
respective Bluetooth
name in the cen-
tre console TV screen.
6. Select the external device you want to pair
with and press OK/MENU.
7. Enter the series of numbers that is shown
in the centre console TV screen via the
external device's keypad and press the
external device's button to confirm the
selection.
The external device is paired and connected
automatically to the infotainment system.
Change audio file by pressing
/ on the
centre console or the steering wheel keypad*.
Automatic connection
When the Bluetooth
function is active and the
last external device connected is in range it is
connected automatically. When the infotain-
ment system searches for the last device con-
nected its name is shown in the TV screen. To
connect to another device, press EXIT. Con-
nect a new external device, see "Change to
another external device" below.
Change to another external device
It is possible to change a connected device
with another device if there are several devices
in the car. However, the device must first have
been paired, see "Pair and connect external
device" above. To change to another device:
1.
Repeatedly press on MEDIA until
Bluetooth is shown, release and wait a
second or press OK/MENU.
2. Check that the external device is searcha-
ble/visible via Bluetooth
, see the manual
for the external device.
3.
Press OK/MENU.
4.
Turn TUNE to
Change device, and con-
firm with OK/MENU.
> After a while, the external device's name
is shown in the TV screen. If several
external devices have been paired then
these are also shown.
5. Select the device to be connected by turn-
ing TUNE and confirm with OK/MENU.
> Connection of the external device takes
place.
Change audio file by pressing
/ on the
centre console or the steering wheel keypad*.
05 Infotainment system
Media Bluetooth
*
05
248
* Option/accessory, for more information, see Introduction.
Remove the connected device
1.
Press Bluetooth mode on OK/MENU.
2.
Turn TUNE to
Remove Bluetooth
device
and confirm with OK/MENU.
3. Select the device to be removed by turning
TUNE, and confirm with OK/MENU.
> A prompt asking whether or not you
want to remove the connection is shown
in the TV screen.
4.
Press OK/MENU to confirm.
EXIT cancels.
Disconnecting the device
Automatic disconnection takes place if the
external device moves out of the infotainment
system's range. For more information on con-
nection, see page 247.
Random
This function plays back the audio files on the
external device in random order. Activate/
deactivate the random function in Bluetooth
mode under
Bluetooth menu Random.
Change audio file by pressing
/ on the
centre console or the steering wheel keypad*.
Scanning of audio files in external device
This function play backs the first ten seconds
of each audio file. Activate/deactivate the func-
tion in Bluetooth mode under
Bluetooth menu
Scan.
Cancel scanning with EXIT.
Version information Bluetooth
The car's current Bluetooth
version can be
seen in Bluetooth mode under
Bluetooth
menu Bluetooth software version in car.
05 Infotainment system
TV*
05
* Option/accessory, for more information, see Introduction.
249
TV*
General
NOTE
This system only supports TV transmissions
in countries which transmit signals in
mpeg-2 format and follow the DVB-T stand-
ard. The system does not support TV trans-
missions in mpeg-4 format or analogue
transmissions.
NOTE
The TV picture is only shown when the car
is stationary. When the car is moving at a
speed over about 6 km/h the picture disap-
pears,
No visual media available during
driving
appears on the display screen,
although the audio is heard during this time.
The picture reappears when the car has
stopped.
NOTE
The reception is dependent both on how
good the signal strength and signal quality
are. The transmission may be disturbed by
various factors such as tall buildings or the
TV transmitter being far away. Coverage
level can also vary depending on where in
the country you are located.
IMPORTANT
A TV licence is required for this product in
some countries.
Overview
Centre console control panel.
MEDIA key.
Station presets, numeric input
Navigate in channel lists or menus by turn-
ing TUNE.
Confirm your selection or go to the menu
by pressing OK/MENU.
EXIT - leads up in the menu system, stops
the function in progress.
The next available channel is shown by
pressing
/ .
NOTE
If the car is equipped with a steering wheel
keypad* and/or remote control* then in
many cases these can be used instead of
the buttons in the centre console. For a
description of the buttons in the steering
wheel, see page 226. For a description of
the remote control, see page 252.
Menus
The menus inMEDIA are controlled from the
centre console and the steering wheel key-
pad*. For general information on menu naviga-
tion and menu structures, see page 275.
Watch TV
If this is the first time the TV function is used or
the country of residence has changed then the
setting of TV channels must first be carried out.
To set the TV channels to see the sec-
tion "Searching TV channels/Preset list" page
250.
–
Repeatedly press on MEDIA until TV is
shown in the TV screen, release the button
and wait a second or press OK/MENU.
> A search starts and after a short while
the most recently used channel is
shown.
Changing channel
It is possible to change channel as follows:
05 Infotainment system
TV*
05
250
* Option/accessory, for more information, see Introduction.
•
Turn TUNE, a list of all available channels
in the area is shown. If any of these chan-
nels is already saved as a preset then its
preset number is shown to the right of the
channel name. Continue turning TUNE to
reach the desired channel and press OK/
MENU.
•
By pressing the preset buttons (0-9).
•
Via a short press on the
/ buttons
the next available channel in the area is
shown.
NOTE
If the car has been moved within the coun-
try, for example, from one city to another, it
is not certain that the presets are available
at the new location as the frequency range
may have changed. In which case, carry out
a new search and save a new preset list, see
the function "Save the available TV channels
as presets", page 251.
NOTE
If no reception is available on the preset
buttons, it may be because the car is at a
location other than where the scan of TV
channels was run, for example, if the car
was driven from Germany to France. A new
selection of country and a new search may
then need to be carried out.
Searching TV channels/Preset list
1.
Press TV mode on OK/MENU.
2.
Turn TUNE to
TV menu and press OK/
MENU.
3.
Turn TUNE to
Select country and press
OK/MENU.
> If one or more countries have previously
been selected then they are shown in a
list.
4.
Turn TUNE to either
Other countries or
one of the previously selected countries.
Press OK/MENU.
> A list of all available countries is shown.
5.
Turn TUNE to the desired country (e.g.
Sweden) and press OK/MENU.
> An automatic scan for available TV
channels starts, this scan takes a little
while. During this time the figure for
each channel found and added as a pre-
set is shown. When the scan is com-
plete a message is shown and the pic-
ture is shown. A preset list (max. 30 pre-
sets) has now been created and is avail-
able. To change channel, see
page 249.
The scan and preset storage can be cancelled
with EXIT.
NOTE
If the country of residence has changed, a
new scan of TV channels must be run.
Channel management
The preset list can be edited. You can change
the order of the channels that are shown in the
preset list. A TV channel can have more than
one place in the preset list. The TV channel
positions can also vary in the preset list.
To change the order in the preset list, go in TV
mode to
TV menu Reorganize presets.
1.
Turn TUNE to the channel you want to
move in the list and confirm with OK/
MENU.
> The selected channel is highlighted.
2.
Turn TUNE to the new location in the list
and confirm with OK/MENU.
> The channels change places with each
other.
After the preset channels (max. 30) come all the
other channels available in the area. It is pos-
sible to move a channel up to a place in the
preset list.
05 Infotainment system
TV*
05
* Option/accessory, for more information, see Introduction.
251
Save the available TV channels as
presets
If the car has been moved within the country,
for example, from one city to another, it is not
certain that the presets are available at the new
location as the frequency range may have
changed. In which case, carry out another scan
and save a new preset list.
1.
Press TV mode on OK/MENU.
2.
Turn TUNE to
TV menu and press OK/
MENU.
3.
Turn TUNE to
Autostore and press OK/
MENU.
> An automatic scan for available TV
channels starts, this scan takes a little
while. During this time the figure for
each channel found and added as a pre-
set is shown. When the scan is com-
plete a message is shown and the pic-
ture is shown. A preset list (max. 30 pre-
sets) has now been created and is avail-
able. To change channel, see
page 249.
Scanning the TV channels
This function automatically scans through the
frequency range for all channels available in the
area where you are. When a channel is found,
it is shown for approx. 10 seconds before
scanning is resumed. Scanning is stopped with
EXIT, then the channel that you just watched
continues to be shown. Scanning does not
affect the preset list.
Activate scanning in TV mode under
TV menu
Scan.
Teletext
It is possible to read Teletext. Follow these
steps:
1.
Press the
button on the remote con-
trol.
2. Enter the page number (3 digits) with the
number keys (0-9) to select page.
> The page is shown automatically.
Enter new page number, or press the remote
control buttons
/ to go to the next page.
Return to TV screen with EXIT or by pressing
the button on the remote control.
It is also possible to control the teletext with the
coloured buttons on the remote control.
Information about the current
programme
Press the INFO button in order to display the
information about the current programme, the
next programme and its start time. If the
INFO button is pressed once more then addi-
tional information on the current programme
can sometimes be displayed, such as start and
end times and a brief description of the current
programme. For more information on the
INFO button, see page 229.
To return to the TV picture, wait several sec-
onds or press EXIT.
Picture settings
The settings for brightness and contrast can be
adjusted. For more information, see page 242.
The reception is lost
If the reception for the TV channel that is being
shown disappears then the picture will freeze.
Shortly after this a message appears informing
that the reception has been lost for the current
TV channel, and a new search for the channel
continues. When the reception returns the dis-
play of the TV channel starts immediately. It is
possible to change channel at any time when
the message is shown.
If the message
Reception lost, searching is
shown then this is because the system has
detected that there is no reception for all TV
channels. One possible reason may be that a
border has been crossed and that the system
is set to the wrong country. In which case,
change to the right country in accordance
with "Searching TV channels/Preset list", see
page 250.
05 Infotainment system
Remote control*
05
252
* Option/accessory, for more information, see Introduction.
Remote control*
Scroll wheel, corresponds to TUNE in the
centre console.
The remote control can be used for all func-
tions in the infotainment system. The remote
control's buttons have the same functions as
the buttons in the centre console or steering
wheel keypad*.
When using the remote control, first press the
remote control's button
to position F.
Then aim the remote control at the IR receiver,
which is located to the right of the INFO button
(see page 229) in the centre console.
If the car is fitted with rear TV screens* and you
want to operate one of these, select the
required TV screen with the button
on the
remote control. Then aim the remote control at
the IR receiver for the TV screen to be oper-
ated, see page 266.
WARNING
Keep loose objects such as mobile phones,
cameras, remote controls for accessories,
etc. in the glove compartment or other com-
partments. Otherwise they may injure peo-
ple in the car in the event of sudden braking
or a collision.
NOTE
Do not expose the remote control to direct
sunlight (e.g. on the instrument panel) - oth-
erwise problems may arise with the batter-
ies.
Key Function
Change between:
L = Rear left TV screen*
F = Front TV screen
R = Rear right TV screen*
Change to navigation*
Change to radio source (AM,
FM1 etc.)
Change to media source (Disc,
TV* etc.)
Change to Bluetooth
hands-
free*
Scroll/fast rewind, change track/
song.
Play/pause
05 Infotainment system
Remote control*
05
* Option/accessory, for more information, see Introduction.
253
Key Function
Stop
Scroll/fast forward, change
track/song.
Menu
To previous, cancels function,
deletes input characters
Navigate up/down
Navigate right/left
Confirm selection or go to the
menu system for the selected
source
Volume, decrease
Volume, increase
0-9 Preset channels, number and let-
ter input
Shortcuts for favourite setting.
Key Function
Information about the current
programme, song, etc. Also used
when there is more information
available than can be shown in
the TV screen.
Selection of language for sound-
track
Subtitles, selection of language
for text
Teletext*, On/Off
Replacing the battery in the remote
control
NOTE
Battery life is normally 1-4 years and
depends on how much the remote control
is used.
The remote control is powered by four batter-
ies of the AA/LR6 type.
Take along extra batteries for a long journey.
1. Push down the catch on the battery cover
and slide the battery cover in the direction
of the infrared lens.
2. Remove the used batteries, turn the new
batteries in accordance with the symbols
in the battery compartment and fit them.
3. Refit the cover.
NOTE
Be sure to dispose of the exhausted batter-
ies in an environmentally safe manner.
05 Infotainment system
Bluetooth
handsfree*
05
254
* Option/accessory, for more information, see Introduction.
General
System overview.
Mobile phone
Microphone
Steering wheel keypad
Centre console control panel
Bluetooth
1
A mobile phone equipped with Bluetooth
can
be connected wirelessly to the Infotainment
system. The infotainment system then works
handsfree, with the option to control a range of
the mobile phone's functions remotely. The
microphone used is located by the driver's sun
visor (2). The mobile phone can be operated by
its own keys irrespective of whether or not it is
connected.
NOTE
Only a selection of mobile phones are fully
compatible with the handsfree function.
Volvo recommends that you seek assis-
tance from an authorised Volvo dealer or
visit for information on
compatible phones.
Menus
The menus in TEL are controlled from the cen-
tre console and the steering wheel keypad*.
For general information on menu navigation
and menu structures, see page 275.
Phone functions, controls overview
Centre console control panel.
Number and letter buttons
TEL - Activate/Disconnect
TUNE - Turn in normal view to the right to
access the phone book, and to the left for
the call register for all calls; also used for
navigation among the options on the TV
screen.
Accept incoming calls, confirm your selec-
tion or go to the Phone menu by pressing
OK/MENU.
EXIT - Cancels/rejects phone calls, deletes
input characters, leads up in the menu sys-
tem and cancels the current function.
1
Applies to High Performance, High Performance Multimedia and Premium Sound Multimedia.
05 Infotainment system
Bluetooth
handsfree*
05
* Option/accessory, for more information, see Introduction.
255
NOTE
If the car is equipped with a steering wheel
keypad* and/or remote control* then in
many cases these can be used instead of
the buttons in the centre console. For a
description of the buttons in the steering
wheel, see page 226. For a description of
the remote control, see page 252.
Remember
Activate/deactivate
A short press on TEL activates the handsfree
function. The
symbol indicates that the
handsfree function is active.
Connect mobile phone
A mobile phone is connected in different ways
depending on whether or not it has been con-
nected previously. To connect a mobile phone
for the first time, follow the instructions below:
There are two options for connecting a mobile
phone, either via the car's menu system or via
the mobile phone's menu system. If one option
does not work then try with the other.
Alternative 1 - via the car's menu system
1. Make the mobile phone detectable/visible
via Bluetooth
, see the mobile phone's
manual or
2. Activate the vehicle's handsfree function
by pressing TEL. Continue by pressing
OK/MENU.
3.
Select,
Change phone, press OK/
MENU.
>
The menu option
Add phone is shown
on the TV screen. If one or more mobile
phones have already been paired then
these are also shown. Press OK/
MENU.
4. Check that the mobile phone's
Bluetooth
function is switched on and
press OK/MENU.
> The audio system searches for mobile
phones in the vicinity. The search takes
approximately 30 seconds. The mobile
phones detected are specified with their
respective Bluetooth
name in the TV
screen. The handsfree function's
Bluetooth
name is shown in the mobile
phone as
My Volvo Car.
5. Choose one of the mobile phones in the
centre console TV screen.
6. Enter the series of numbers that is shown
in the centre console TV screen via the
mobile phone's keypad and press the
mobile phone's button to confirm the
selection.
Alternative 2 - via the mobile phone's menu
system
1. Activate the handsfree function by press-
ing TEL in the centre console. If there is a
phone connected, disconnect the con-
nected phone.
2. Make the car detectable/visible via
Bluetooth
, press OK/MENU and activate
the
Phone settings Discoverable
option.
3. Search with the mobile phone's
Bluetooth
function, see the mobile phone
manual.
4.
Select
My Volvo Car in the list of units
detected in your mobile phone.
5. Enter an optional PIN code on your mobile
phone via the mobile phone's keypad
when prompted to enter the PIN code.
Then key in the same PIN code via the car's
keypad.
6.
Select to connect to
My Volvo Car from
the mobile phone.
The mobile phone is paired (registered) and
connects automatically to the audio system.
For more information about how mobile
phones are paired, see page 257.
When the connection is established the mobile
phone's Bluetooth
name is shown in the TV
05 Infotainment system
Bluetooth
handsfree*
05
256
* Option/accessory, for more information, see Introduction.
screen. Now the mobile phone can be con-
trolled from the audio system.
To call
1.
Make sure that the
symbol appears
at the top of the TV screen and that the
handsfree function is in phone mode.
2. Dial either the desired number or speed
dial number, see page 261. Or in normal
view turn TUNE to the right to access the
phone book, and to the left for the call reg-
ister for all calls. For information on the
phone book, see page 258.
3.
Press OK/MENU.
The call is interrupted with EXIT.
Disconnecting the mobile phone
Automatic disconnection takes place if the
mobile phone moves out of the audio system's
range. The connection to the mobile phone can
be interrupted manually via a long press on
TEL or in phone mode under
Phone menu
Disconnect phone. For more information
on connection, see page 257.
The handsfree function is deactivated when
the engine is switched off or when a door is
opened
2
.
When the mobile phone has been discon-
nected an ongoing call can be continued by
using the mobile phone's built-in microphone
and speaker.
NOTE
Even when your mobile phone has been
manually disconnected, some mobile
phones may automatically couple up to the
last handsfree unit connected, e.g. when a
new call begins.
Making and receiving calls
Incoming call
–
Press OK/MENU to answer the call, even
if the audio system is in e.g.
RADIO or
MEDIA mode.
Refuse or end with EXIT.
Automatic answer
The automatic answer function means that
calls are accepted automatically.
– Activate/deactivate in phone mode under
Phone menu Call options Auto
answer
.
In call menu
Press OK/MENU during an ongoing call to
access the following functions:
•
Mute - audio system microphone is
muted.
•
Mobile phone - the call is transferred from
handsfree to the mobile phone. For some
mobile phones the connection is interrup-
ted. This is normal. The handsfree function
asks if you want to reconnect.
•
Dial number - option to call a third party
using the number keys (current call set in
standby).
Call lists
The call lists are copied to the handsfree func-
tion at each new connection and are then
updated during the connection. In normal view,
turn to the left with TUNE to see the call register
for
All calls .
In phone mode it is possible to see all the call
lists under
Phone menu All calls:
•
All calls
•
Missed calls
•
Answered calls
•
Dialled calls
•
Call duration
2
Only Keyless Drive.
05 Infotainment system
Bluetooth
handsfree*
05
* Option/accessory, for more information, see Introduction.
257
NOTE
Certain mobile phones show a list of the last
dialled numbers in reverse order.
Voice mailbox
In normal view a speed dial number for the
voice mailbox can be programmed in and then
accessed later via a long press on 1.
Voice mailbox number is changed in phone
mode under
Phone menu Call options
Voicemail number Change number. If
there is no number stored then this menu can
be reached with one long press on 1.
Audio settings
Phone call volume
The phone call volume can only be changed
during a call. Use the steering wheel keypad*
or turn the VOL control.
Audio system volume
Providing there is no ongoing call taking place,
the audio system volume is controlled as usual
by turning VOL.
If an audio source is active during an incoming
call then it can be muted automatically. Acti-
vate/deactivate in phone mode under
Phone
menu
Phone settings Sounds and
volume
Mute radio/media.
Ring volume
In phone mode go to Phone menu Phone
settings
Sounds and volume Ring
volume and adjust by turning VOL. Press
EXIT to save.
Ring signals
The handsfree function has integrated ring sig-
nals that can be selected in phone mode under
Phone menu Phone settings Sounds
and volume
Ring signals Ring signal 1
etc.
NOTE
For some mobile phones, the ringtone on
the phone connected will not be switched
off when one of the inbuilt signals for the
handsfree system is used.
In order to select the connected phone's ring
signal
3
, go in phone mode to
Phone menu
Phone settings Sounds and volume
Ring signals Mobile phone ring signal.
More on pairing and connecting
A maximum of ten mobile phones can be
paired (registered). Pairing is performed once
per phone. After pairing the phone no longer
needs to be visible/detectable. A maximum of
one mobile phone can be connected at a time.
Automatic connection
When the handsfree function is active and the
last mobile phone connected is in range it is
connected automatically. If the last connected
mobile phone is not available then the system
will try to connect a mobile phone that was
paired earlier. When the audio system
searches for the last phone connected its name
is shown in the TV screen.
Manual connection
If you want to change the connected mobile
phone, go in phone mode to Phone menu
Change phone.
Remove the device
A connected mobile phone can be deregis-
tered and removed. This is performed in phone
mode under
Phone menu Remove
Bluetooth device
.
3
Not supported by all mobile phones.
05 Infotainment system
Bluetooth
handsfree*
05
258
* Option/accessory, for more information, see Introduction.
Version information Bluetooth
The car's current Bluetooth
version can be
seen in phone mode under Phone menu
Phone settings Bluetooth software
version in car
.
Phone book
There are two phone books. These are merged
into one in the car and are displayed as a single
phone book in the car.
•
The car downloads the mobile phone's
phone book and only displays this phone
book when the mobile phone from which
this phone book was downloaded is con-
nected.
•
The car also has a built-in phone book. This
contains all the contacts stored in the car
irrespective of which phone was con-
nected when saving them. These contacts
are visible for all users, regardless of the
mobile phone that is connected to the car.
If a contact is saved in the car then the
symbol
is shown in front of the con-
tact in the phone book.
NOTE
Changes made from the car to a record in
the mobile phone's telephone book will
result in a new record in the car's telephone
book, i.e. changes will not be saved to the
phone. From the car, this will now look like
you have double records, with different
icons. Note also that when a shortcut num-
ber is saved or a change to a contact is
made, this will result in a new record in the
car's phone book.
All use of the phone book requires that the
symbol appears at the top of the TV
screen and that the handsfree function is in
phone mode.
The audio system stores a copy of the phone
book from each paired mobile phone. The
phone book can be copied automatically to the
audio system during each connection.
– Activate/deactivate the function in phone
mode under Phone menu Phone
settings
Phonebook download.
If the phone book contains a ringing caller's
contact information then this is shown in the TV
screen.
Quick search for contacts
In normal view turn TUNE to the right to obtain
a list of contacts. Turn TUNE to select and
press OK/MENU to call.
Under the name of the contact is the phone
number that is selected by default. If the sym-
bol
appears to the right of the contact then
there are several phone numbers stored for the
contact. Change and dial a different number
than the one that is selected by default by
pressing the button
on the control panel
in the centre console. Then turn TUNE to select
and press OK/MENU to call.
Search in the list of contacts by using the cen-
tre console's keypad to key in the start of the
contact's name (see "Character table keypad
in centre console" for button functions).
The list of contacts can also be accessed from
normal view by pressing and holding the button
on the centre console's keypad with the letter
that the contact searched for starts with. For
example, a long press on the button for 6 gives
instant access to that part of the list where the
contacts with the letter
M are located.
05 Infotainment system
Bluetooth
handsfree*
05
* Option/accessory, for more information, see Introduction.
259
Character table keypad in centre
console
Key Function
Space . , - ? @ : ; / ( ) 1
A B C Å Ä Æ À Ç 2
D E F È É 3
G H I Ì 4
J K L 5
M N O Ö Ø Ñ Ò 6
P Q R S ß 7
T U V Ü Ù 8
W X Y Z 9
Shift between upper and lower
case letter.
Key Function
+ 0 p w
# *
Searching for contacts
Search contacts using the text wheel.
Character list
Changing the input mode (see table below)
Phone book
To search for or edit a contact, go in phone
mode to Phone menu
Phone book
Search.
NOTE
There is no text wheel for High Performance,
so TUNE cannot be used there to input
characters: only the digit and letter buttons
on the control panel in the centre console
can be used for this.
1.
Turn
4
TUNE to the desired letter, press
OK/MENU to confirm. The number and
letter buttons on the control panel in the
centre console can also be used.
2. Continue with the next letter and so on. The
result of the search is shown in the phone
book (3).
3. To change the input mode to numbers or
special characters, or to go to the phone
book, turn TUNE to one of the options (see
explanation in the table below) in the list for
changing the input mode (2), press OK/
MENU.
4
Only applies to High Performance Multimedia and Premium Sound Multimedia.
05 Infotainment system
Bluetooth
handsfree*
05
260
* Option/accessory, for more information, see Introduction.
123/
ABC
Change between letters and
numbers with OK/MENU.
More
Change to special characters
with OK/MENU.
Leads to the phone book (3).
Turn TUNE to select a contact,
press OK/MENU to see the
saved numbers and other infor-
mation.
A short press on EXIT deletes an input char-
acter. A long press on EXIT will clear all entered
characters.
By pressing a number key in the centre console
when the text wheel is shown (see illustration
above), a new character list (1) appears in the
TV screen. Continue repeatedly pressing the
number key to the desired letter and then
release. Continue with the next letter and so
on. When a button is depressed the entry is
confirmed when another button is depressed.
To enter a number, hold in the corresponding
number key.
New contact
Entering letters for New contact.
Changing the input mode (see table below)
Input field
New contacts can be added in phone mode
under Phone menu
Phone book New
contact.
NOTE
There is no text wheel for High Performance,
so TUNE cannot be used there to input
characters: only the digit and letter buttons
on the control panel in the centre console
can be used for this.
1.
When the
Name row is selected, press
OK/MENU to reach the input mode (illus-
tration above).
2.
Turn
4
TUNE to the desired letter, press
OK/MENU to confirm. The number and
letter buttons on the control panel in the
centre console can also be used.
3. Continue with the next letter and so on. The
name entered is shown in the input field (2)
in the TV screen.
4. To change the input mode to numbers,
special characters, change between
uppercase/lowercase letters, etc., turn
TUNE to one of the options (see explana-
tion in the table below) in the list (1) and
then press OK/MENU.
When the name has been fully entered, select
OK in the list on the TV screen (1) and press
OK/MENU. Now continue with the telephone
number in the same way as above.
When the telephone number has been entered,
press OK/MENU and select a telephone num-
ber type (
Mobile, Home, Work or General).
Press OK/MENU to confirm.
When all details have been filled in, select
Save
contact
in the menu to save the contact.
4
Only applies to High Performance Multimedia and Premium Sound Multimedia.
05 Infotainment system
Bluetooth
handsfree*
05
* Option/accessory, for more information, see Introduction.
261
123/
ABC
Change between letters and
numbers with OK/MENU.
More
Change to special characters
with OK/MENU.
OK Save and go back to Add con-
tact
with OK/MENU.
Change between uppercase and
lowercase letters with OK/
MENU.
Press OK/MENU, the cursor
moves to the input field (2) at the
top of the TV screen. The cursor
can now be moved, with TUNE,
to the appropriate place to e.g.
insert new letters or delete with
EXIT. To be able to insert new
letters first go back to the input
mode, by pressing OK/MENU.
Speed dial numbers
Use phone mode to add speed dial numbers
under Phone menu Phone book Speed
dial.
Dialling with speed dial numbers can be per-
formed in phone mode using the number keys
on the keypad in the centre console, by press-
ing a number key and then pressing OK/
MENU. If there is no contact stored on the
speed dial number then an option is shown to
save a contact to the selected speed dial num-
ber.
Receiving a vCard
It is possible to receive a vCard to the car's
phone book from other mobile phones (other
than the one currently connected to the car). In
order to allow this the car is set to visible mode
for Bluetooth
. The function is activated in
phone mode under
Phone menu Phone
book
Receive vCard.
Memory status
Memory status of the car's phone book and the
connected mobile phone's phone book can be
seen in phone mode under
Phone menu
Phone book Memory status.
Delete phone book
The car's phone book can be deleted, this is
carried out in phone mode under
Phone menu
Phone book Clear phone book.
NOTE
Deleting the car's telephone book only dele-
tes contacts in the car's telephone book.
Contacts in the mobile phone's phone book
are not deleted.
05 Infotainment system
Voice recognition* mobile phone
05
262
* Option/accessory, for more information, see Introduction.
Introduction
The infotainment system's voice recognition
1
allows the driver to voice-activate certain func-
tions in a Bluetooth
-connected mobile phone
or in Volvo's navigation system - RTI (Road and
Traffic Information System).
NOTE
•
The information in this section
describes the use of voice commands
to control a mobile phone connected
using Bluetooth
. For detailed infor-
mation on using a mobile phone con-
nected using Bluetooth
with the car's
Infotainment system see page 254.
•
The Volvo navigation system RTI (Road
and Traffic Information System) has a
separate user manual which contains
more information on voice control and
voice commands to control that sys-
tem.
Voice commands offer convenience and help
the driver to avoid being distracted, and
instead concentrate on driving and focus
attention on the road and traffic conditions.
WARNING
The driver always holds overall responsibil-
ity for driving the vehicle in a safe manner
and complying with all applicable rules of
the road.
The voice recognition system allows the driver
to voice-activate certain functions of a
Bluetooth
-connected mobile phone and in
Volvo's navigation system - RTI (Road and
Traffic Information System), while the driver
can keep his/her hands on the wheel at the
same time. The input data are in dialogue form
with spoken commands from the user and ver-
bal replies from the system. The voice recog-
nition system uses the same microphone as
the Bluetooth
handsfree system (see illustra-
tion on page 254) and the voice recognition
system's replies come via the car's speakers.
Language
Language list.
Voice recognition is not possible for all lan-
guages. Languages available for voice recog-
nition are marked with an icon in the language
list -
. Changing the language is performed
in the menu system MY CAR, see page 148.
1
Only applies to vehicles equipped with Volvo's navigation system - RTI (Road and Traffic Information System).
05 Infotainment system
Voice recognition* mobile phone
05
* Option/accessory, for more information, see Introduction.
263
Remember
Steering wheel keypad.
Button for voice recognition
To activate the system
Before voice commands to a mobile phone can
be used the mobile phone must be paired and
connected via Bluetooth
handsfree. If a tele-
phone command is given and no mobile phone
is paired, then the system will provide informa-
tion about this. For information on pairing and
connecting a mobile phone, see page 255.
•
Press the button for voice recognition (1) in
order to activate the system and initiate a
dialogue with voice commands. The sys-
tem will then display commonly used com-
mands in the TV screen in the centre con-
sole.
Keep the following things in mind when you use
the voice recognition system:
•
For a command - speak after the tone, with
normal voice at normal speed.
•
Do not speak while the system is replying
(the system cannot understand commands
during this time).
•
The car's doors, windows and sunroof*
must be closed.
•
Avoid background noise in the passenger
compartment.
NOTE
If the driver is unsure of which command to
use, he (she) can say "Help" - the system
then responds with a few different com-
mands which can be used in the current sit-
uation.
Voice commands can be disabled by:
•
saying "Cancel"
•
not speaking
•
a long press on the steering wheel but-
ton for Voice recognition
•
Press EXIT or another source button
(e.g. MEDIA).
Help functions for voice recognition
•
Instructions: A function that helps you get
familiar with the system and the procedure
for giving commands.
•
Voice training: A function that enables the
voice recognition system to learn to know
your voice and your accent. The function
provides an opportunity to voice train two
user profiles.
The help functions can be accessed by press-
ing the MY CAR button on the control panel in
the centre console and then turning TUNE to
the desired menu option.
Instructions
The instructions can be started in two ways:
NOTE
This instruction and voice training can only
be started when the car is parked.
•
Press the button for Voice recognition and
say "Voice instructions".
•
Activate the instructions in the menu sys-
tem MY CAR under
Settings Voice
settings
Voice tutorial. For a descrip-
tion of the menu system, see page 146.
The instructions are divided into 3 lessons,
which take around 5 minutes in total to com-
plete. The system starts with the first lesson.
05 Infotainment system
Voice recognition* mobile phone
05
264
* Option/accessory, for more information, see Introduction.
To skip a lesson and go to the next one, press
the button for voice recognition and say
"Next". Go back to the previous lesson by say-
ing "Previous".
Exit the instructions by means of a long press
on the button for voice recognition.
Voice training
The system displays up to fifteen phrases for
you to say. Voice training can be started in the
menu system MY CAR under
Settings
Voice settings Voice training. Choose
between
User 1 or User 2. For a description
of the menu system, see page 146.
After voice training has been completed,
remember to set your user profile under
Voice
user setting
.
Additional settings in MY CAR
•
User setting - Two user profiles can be
set, the function is activated in the menu
system MY CAR under
Settings Voice
settings
Voice user setting. Choose
between
User 1 or User 2. For a descrip-
tion of the menu system, see page 146.
•
Voice volume - Can be changed in the
menu system MY CAR under
Settings
Voice settings Voice output
volume
. For a description of the menu sys-
tem, see page 146.
Using voice commands
The driver initiates a dialogue with the voice
commands by pressing the button for voice
recognition (see illustration on page 263).
Once a dialogue has been started, commonly
used commands will be shown in the TV
screen. Greyed-out text or text within brackets
is not included in the spoken command.
When the driver becomes accustomed to the
system, he/she can speed up the command
dialogue and skip the prompts from the sys-
tem, by briefly pressing the button for voice
recognition.
Commands can be given in several ways
The command "Phone call contact" can be
pronounced as e.g.:
•
"Phone > Call contact" - Say "Phone", wait
for the system's reply, and then continue
by saying "Call contact."
or
•
"Phone call contact" - Say the whole com-
mand in one sequence.
Quick commands
Quick commands for the phone can be found
in the menu system MY CAR under
Settings
Voice settings Voice command list
Phone commands and General
commands
. For a description of the menu
system, see page 146.
Dial a number
The system understands the numbers 0 (zero)
to 9 (nine). These numbers can be pronounced
individually, in groups of several numbers at a
time, or the whole number all at once. Numbers
greater than 9 (nine) cannot be handled by the
system, e.g. 10 (ten) or 11 (eleven) are not pos-
sible.
The following is an example of a dialogue with
voice commands. The system's reply will vary
depending on the situation.
The user starts the dialogue by saying:
Phone > call number
or
Phone call number
System reply
Number?
User action
Start saying the numbers (as individual units,
i.e. six-eight-seven, etc.) in the phone number.
If you say several numbers and pause, the sys-
tem will repeat them, and then say "Continue".
Continue to say the numbers. When finished,
finish the command by saying "Call".
•
You can also change the number by saying
the commands "Correct" (which deletes
05 Infotainment system
Voice recognition* mobile phone
05
* Option/accessory, for more information, see Introduction.
265
the last spoken group of numbers) or
"Delete" (which deletes the whole spoken
phone number).
Dialling from the call register
The following dialogue allows you to make a
phone call from one of your mobile phone's call
registers.
The user starts the dialogue by saying:
Phone > call from the call register
or
Phone call from the call register
Continue by responding to the system's
prompts.
Call a contact
The following dialogue allows you to call your
pre-defined contacts in the mobile phone.
The user starts the dialogue by saying:
Phone > call contact
or
Phone call contact
Continue by responding to the system's
prompts.
Consider the following when you call a contact:
•
If there are several contacts with similar
names, they will be presented in the dis-
play in the numbered rows and the system
prompts you to select a row number.
•
If there are more rows in the list than can
be displayed simultaneously, saying
"Down" allows you to scroll down in the list
(and saying "Up" allows you to scroll up in
the list).
Calling voice mailbox
The following dialogue allows you to call your
voice mailbox to check if you have received
any messages. The phone number for your
voice mailbox must be registered in the
Bluetooth
function, see page 257.
The user starts the dialogue by saying:
Phone > call voice mailbox
or
Phone call voice mailbox
Continue by responding to the system's
prompts.
05 Infotainment system
RSE - Rear Seat Entertainment system*
05
266
* Option/accessory, for more information, see Introduction.
Overview
TV screen
Headphones socket
On/Off button
A/V-AUX input
Remote control
Headphones
IR receiver/transmitter
General
The RSE system is a system for rear-seat
entertainment that makes it possible to e.g.
watch video, play music, listen to the radio,
watch TV* or connect other external devices
(e.g. a games console).
The RSE system is fully integrated with the
car's infotainment system and can be used
simultaneously with other functions of the info-
tainment system.
When the rear seat passengers are using e.g.
A/V-AUX or watching TV* while listening with
headphones, the driver and front seat passen-
ger can still use the car's radio or media player.
However, only one disc at a time can be played
in the media player. It is possible to play back
music from e.g. an iPod
or steaming audio
files via Bluetooth
.
The RSE system can be controlled from the
front TV screen (parental control).
It is possible to display or play back various
media from different sources on each TV
screen. It is also possible to display or play
back media from the same source on one or
more of the TV screens (front, right rear and left
rear). It is not possible to play back video from
05 Infotainment system
RSE - Rear Seat Entertainment system*
05
* Option/accessory, for more information, see Introduction.
267
USB while a CD or DVD disc is being played
back.
IMPORTANT
When loading luggage and large objects in
the vehicle, ensure that sufficient space is
left for the TV screens in the head restraints,
so that the TV screens are not scratched or
damaged. Cover the TV screens with appro-
priate covering material during loading.
NOTE
The TV screens and remote control do not
work at very low or high temperatures - they
only "come alive" after the climate control
system has created an acceptable operat-
ing temperature in the passenger compart-
ment.
NOTE
Clean the lens on the IR receiver regularly
with a damp cloth, a dirty lens affects
remote control function.
Power consumption, ignition positions
The system can be activated in ignition position
I or II and while the engine is running. When the
car is being started the film stops temporarily
and continues when the engine has started.
NOTE
For prolonged use (more than 10 minutes)
with the engine switched off, the capacity of
the vehicle's battery may fall to such a low
level that it is not possible to start the
engine.
In this case a message will be displayed on
the screen.
Menus
The menus for RSE are controlled using the
remote control. For general information on
menu navigation and menu structures, see
page 272.
Remote control
The RSE system is equipped with a remote
control. Using this it is possible to control the
functions for each TV screen. The remote con-
trol can also be used to control other functions
in the infotainment system, even from the rear
seat.
For information on the remote control, see
page 252.
Wireless headphones
Control for channel A (CH.A) or channel B
(CH.B)
On/Off button
Volume
Indicator lamp On/Off
The RSE system includes two wireless head-
phones.
The wireless headphones are activated with
the On/Off button (2), an indicator lamp illumi-
nates (4). Select CH.A (channel A) or CH.B
(channel B) using the control (1). Adjust the vol-
ume using the volume control (3).
The headphones are automatically switched
off after about 3 minutes if they are not used.
05 Infotainment system
RSE - Rear Seat Entertainment system*
05
268
* Option/accessory, for more information, see Introduction.
Battery replacement in wireless
headphones
The headphones are powered by two batteries
of the AAA model.
Take along extra batteries for a long journey.
Wireless headphones.
1. Unscrew the screw and detach the battery
cover.
2. Remove the used batteries, turn the new
batteries in accordance with the symbols
in the battery compartment and insert
them.
3. Fit the cover and screw in the screw.
Environmental care
Be sure to dispose of the exhausted batteries
in an environmentally safe manner.
Headphones socket
It is possible to connect external headphones
via the headphones socket (3.5 mm) on the
side of the head restraints, see the illustration
on page 266. The volume is controlled using
the remote control.
A/V-AUX input, Electrical socket 12 V
The input allows you to connect other equip-
ment. Always follow the instructions included
with the external equipment, or from the man-
ufacturer or reseller, when connecting. Equip-
ment connected via the A/V-AUX input can use
the TV screens, wireless headphones, head-
phones sockets and the car's speakers.
NOTE
The customer is responsible that equipment
connected to the A/V-AUX input or head-
phones socket does not cause interference
in the vehicle's RSE system.
Connection of A/V-AUX input
The A/V-AUX input is located under the armrest in
the tunnel console.
1. Connect the video cable to the yellow
socket.
2. Connect the left-hand audio cable to the
white socket and the right-hand one to the
red socket.
3. Connect the power cable to the electrical
socket if your equipment is designed for 12
V.
Always follow the instructions for the external
equipment when connecting.
There is a recess in the right-hand rear edge of
the tunnel console where cables can be routed
so that the hatch can be closed without cables
being pinched.
05 Infotainment system
RSE - Rear Seat Entertainment system*
05
``
* Option/accessory, for more information, see Introduction.
269
For electrical socket location, see page 217
Playing back audio/video via the A/V-
AUX input
1. Switch on the rear TV screen by means
pressing the On/Off button on the TV
screen.
2. Aim the remote control at the IR receiver
on the TV screen and press repeatedly on
to the source A/V AUX , release and
wait a few seconds and the selection is
accepted.
3. Switch on the connected device and press
PLAY or equivalent on the connected
device.
Input volume
The input volume is adjusted in the menu under
A/V AUX input volume.
To activate the system
The RSE system can be activated from either
the front or rear TV screen.
From the front TV screen, press MEDIA and
select
RSE.
From the rear TV screen, by means of pressing
the On/Off button on the rear TV screen and
then pressing
or on the remote
control and selecting a source (e.g. Disc).
Settings from the front TV screen
MEDIA
TUNE
OK/MENU
EXIT
Selection of source in the rear TV
screens
From the front TV screen it is possible to select
the source (what shall be displayed or played
back) for the right and left-hand rear TV
screens respectively. It is possible select the
same source for both or different sources for
the right and left-hand TV screens respectively.
1.
Press on MEDIA, press repeatedly in order
to scroll to
RSE on the TV screen, release
and wait a second and the selection is
accepted automatically.
2.
Turn TUNE to select the right, left-hand or
both TV screens, and confirm with OK/
MENU.
3.
Turn TUNE to select
RADIO, MEDIA (or
RSE settings). Press OK/MENU to con-
firm.
4.
Turn TUNE to the desired source (e.g.
Disc) and confirm with OK/MENU. The
selected source will start automatically (if
e.g. a disc is in the media player).
Cancel and go back with EXIT.
The remote control can also be used for set-
tings. For more information on the remote con-
trol, see page 252.
Parental control for the TV*
It is possible to set a permitted age limit for the
TV, so that only programmes for the appropri-
ate age can be viewed. The setting is activated
for both TV screens.
Activate under
RSE settings TV parental
control, in accordance with point 2-4 in the
section "Selection of source in the rear TV
screens", see page 269. Choose between
Age
0-6
, Age 7-13, Age 14-18 and No parental
control
.
05 Infotainment system
RSE - Rear Seat Entertainment system*
05
270
* Option/accessory, for more information, see Introduction.
Audio off
It is possible to mute the two rear TV screens
from the front TV screen. The function is acti-
vated under
RSE settings Mute, in accord-
ance with point 2-4 in the section "Selection of
source in the rear TV screens", see page 269.
TV screen off
It is possible to switch off the video for the two
rear TV screens from the front TV screen. The
function is activated under
RSE settings
Display off, in accordance with point 2-4 in the
section "Selection of source in the rear TV
screens", see page 269.
Press one of the remote control's numeric keys
(0 - 9) to switch on the TV screen again. The TV
screen is also switched to the On mode when
the ignition is switched on.
Switching off the remote control (front)
It is possible to switch off the IR receiver for the
front TV screen, which means that the remote
control cannot be used for the front TV screen.
The function is activated under
RSE settings
Disable remote control (front), in accord-
ance with point 2-4 in the section "Selection of
source in the rear TV screens", see page 269.
TV screen settings
1
rear TV screen
When playing back video files and displaying
TV* a pop-up menu is available by means of
pressing
on the remote control. The pop-
up menu has different content depending on
what is being played back or displayed.
Day/Night mode
The TV screen can be set in three different
modes for different light conditions. Choose
between
Auto, Day and Night.
Press on the remote control and change
the mode under Day/Night mode on the TV
screen. For general information on menu navi-
gation and menu structures, see page 272.
Picture settings
You can adjust the settings for brightness, con-
trast, shade and colour.
Press
on the remote control and change
the mode under
Image settings on the TV
screen. For general information on menu navi-
gation and menu structures, see page 272.
Display format
It is possible to choose between display for-
mats
Normal, Zoom and Screen fit.
Normal - The image is shown in its normal
mode (normally 4:3 or 16:9 format).
Zoom - Full screen used but parts of the image
are cut off.
Screen fit - Full screen used but image pro-
portions may be slightly distorted.
Unless otherwise stated the image is displayed
in the screen format
Normal.
Press on the remote control and change
the mode under
Screen format on the TV
screen. For general information on menu navi-
gation and menu structures, see page 272.
Source menu
What is shown in the pop-up menu for the
source menu depends on what is being played
back or displayed, it can be e.g.
Disc menu or
USB menu. For general information on menu
navigation and menu structures, see
page 272.
DVD disc's menu
2
If a DVD video disc is played back then this
menu option is shown in the pop-up menu. For
general information on menu navigation and
menu structures, see page 272.
1
Only available for playing back video files and displaying TV*.
2
Only applies to DVD video discs.
05 Infotainment system
RSE - Rear Seat Entertainment system*
05
* Option/accessory, for more information, see Introduction.
271
Menu settings from the rear TV screen
For general information on menu navigation
and menu structures, see page 272.
Random
3
See page 241.
Repeat folder
4
See page 241.
DivX
Video On Demand
4
The media player can be registered in order to
play DivX VOD type files from burned discs or
USB. The code for registration is available in
disc mode or USB mode under
DivX® VOD
code
. For more information visit
USB hub
It is possible to connect a USB hub to the USB
connection, see page 244.
TV settings*
Searching TV channels/Preset list
See page 250.
Save the available TV channels as
presets
See page 251.
Scanning the TV channels
See page 251.
Music, video, radio and TV*
Playing back music
It is possible to play back music from disc
tracks/audio files via the car's media player,
USB port/AUX input or via streaming audio files
from a Bluetooth
-connected phone.
NOTE
The system only supports one iPod
user at
a time in the navigation mode (playlist).
For more information about media players,
USB/AUX and Media Bluetooth
, see the
pages 239, 243 and 246.
1. Switch on the wireless headphones, select
CH.A for left-hand screen or CH.B for
right-hand screen.
2. Aim the remote control at the IR receiver
on the TV screen, press repeatedly on
to the desired source (Disc, USB,
AUX etc.), release and wait a few seconds
and the selection is accepted.
3. Insert a CD disc in the car's media player
or connect an external audio source via the
car's USB port/AUX input or via Blue-
tooth
.
Playback and navigation in playlists
Rotate the scroll wheel on the remote control
to access the playlist/folder structure.
either gives confirmation of subfolder selection
or starts playing back the selected disc track/
audio file. It is also possible to play back the
disc track/audio file using
on the remote
control and change the disc tracks/audio file
using
/ . Stop playback using
.
For more information, see page 239.
3
Applies to CD-Audio, CD/DVD discs, USB and iPod
.
4
Applies to CD/DVD discs and USB.
05 Infotainment system
RSE - Rear Seat Entertainment system*
05
272
* Option/accessory, for more information, see Introduction.
Watching video
It is possible to watch video from disc tracks/
video files via the car's media player or USB
port.
For more information about media players and
USB, see the pages 239 and 243.
1. Switch on the wireless headphones, select
CH.A for left-hand screen or CH.B for
right-hand screen.
2. Aim the remote control at the IR receiver
on the TV screen, press repeatedly on
to the desired source (Disc or
USB), release and wait a few seconds and
the selection is accepted.
3. Insert a DVD disc in the car's media player
or connect an external source via the car's
USB port.
Playback and navigation
Play back disc track/video file using on
the remote control and change disc track/
video file using
/ . Stop playback
using
. For more information about play-
back and navigation of DVD video discs, see
page 241 and for video files, see page 239.
Fast forward/reverse
Start fast forward/rewind by means of a long
press on the buttons
/ . Then
increase fast forward/rewind speed by short
presses the buttons. Audio files are fast for-
warded/rewound at one speed, while video
files can be fast forwarded/rewound at four dif-
ferent speeds. Fast forward/rewind is stopped
by pressing
-, - or the equivalent
opposite
/ button.
Listening to radio
It is possible to listen to radio via the car's
radio.
1. Switch on the wireless headphones, select
CH.A for left-hand screen or CH.B for
right-hand screen.
2. Aim the remote control at the IR receiver
on the TV screen, press repeatedly on
to the desired source (AM, FM1,
DAB1* etc.), release and wait a few sec-
onds and the selection is accepted.
3. Select a station with one of the preset but-
tons (0 - 9) on the remote control or press
/ , the radio will search for the
next/previous available station.
For more information on the radio, see
page 232.
Watching TV*
It is possible to watch TV via the car's media
player.
1. Switch on the wireless headphones, select
CH.A for left-hand screen or CH.B for
right-hand screen.
2. Aim the remote control at the IR receiver
on the TV screen, press repeatedly on
to TV, release and wait a few sec-
onds and the selection is accepted.
3. Select a channel with one of the preset
buttons (0 - 9) on the remote control or
press
/ , the next/previous
channel available in the area is displayed.
For more information on the TV, see
page 249.
Menu navigation RSE
General
The RSE menus are operated both from the
front TV screen, and from either of the rear TV
screens. From the front TV screen it is possible
to both activate a source for a rear TV screen,
and to make certain settings for the two rear TV
screens.
05 Infotainment system
RSE - Rear Seat Entertainment system*
05
``
* Option/accessory, for more information, see Introduction.
273
RSE menus front TV screen
To access the menu RSE must first be selected
under MEDIA via the front TV screen. Then
press OK/MENU to access the menu. Turn
TUNE to the desired selection and confirm with
OK/MENU. The remote control and steering
wheel keypad can also be used.
It is possible to make settings for either right or
left-hand TV screen or both TV screens.
Left RSE screen menu, Right RSE screen
menu
and Both RSE screen menus:
Power off/Power on
RADIO
MEDIA
RSE settings
Mute
Display off
Disable remote control (front)
TV parental control
Reset all RSE settings
Pop-up menu RSE
5
Press on the remote control when a
video file is being played back or the TV* is
being displayed in order to access the pop-up
menu. Menu selections are made using the
scroll wheel and the buttons on the remote
control. For information on the remote control,
see page 252.
Screen format
Image settings
Day/Night mode
Source menu
6
DVD disc menu
7
RSE menus rear TV screens
Press on the remote control when a
source (e.g.
Disc) is selected in order to access
the RSE menus for the rear TV screen.
Menu selections are made using the scroll
wheel and the buttons on the remote control.
For information on the remote control, see
page 252.
RADIO
Menu valid for AM, FM1, FM2, DAB1* and
DAB2*:
Day/Night mode
Display off
Reset all RSE settings
MEDIA
RSE CD Audio menu
Disc menu
Random
Day/Night mode
Display off
Reset disc settings
RSE CD/DVD Data menu
Disc menu
Random
Repeat folder
DivX® VOD code
Day/Night mode
5
Only applies when playing back videos or displaying TV*.
6
What is shown in the pop-up menu for the source menu depends on what is being played back or displayed, it can be e.g. Disc menu or USB menu.
7
Only applies to DVD video discs.
05 Infotainment system
RSE - Rear Seat Entertainment system*
05
274
* Option/accessory, for more information, see Introduction.
Display off
Reset disc settings
RSE DVD Video menu
Disc menu
DVD disc menu
Subtitles
Audio tracks
Advanced settings
Day/Night mode
Display off
Reset disc settings
RSE USB menu
USB menu
Random
Repeat folder
DivX® VOD code
Select USB device
Day/Night mode
Display off
Reset USB settings
RSE AUX menu
AUX menu
AUX input volume
Day/Night mode
Display off
Reset AUX settings
RSE A/V-AUX menu
A/V AUX menu
A/V AUX input volume
Day/Night mode
Display off
Reset AUX settings
RSE iPod menu
iPod menu
Random
Day/Night mode
Display off
Reset iPod settings
RSE Bluetooth
menu
Bluetooth menu
Random
Day/Night mode
Display off
Reset Bluetooth settings
RSE TV menu*
TV menu
Select country
Autostore
Scan
Day/Night mode
Display off
Reset TV settings
05 Infotainment system
Menu navigation, Infotainment
05
``
* Option/accessory, for more information, see Introduction.
275
To navigate in the menus
The infotainment system's functions are con-
trolled via the system's menus. Each source in
the infotainment system (e.g. RADIO, MEDIA)
has its own separate menus. In order to access
the menus and activate a function a source
must first have been selected (e.g.
RADIO/
FM1). Then press OK/MENU for access into
the menu for the selected source.
The menu options are selected by means of the
buttons in the centre console or via the steering
wheel keypad*. The functions are described
under their respective sections.
Controls in the centre console
RADIO
MEDIA
TEL
TUNE
OK/MENU
Search paths
The search paths to the menu functions are
specified in the owner's manual with the form:
Audio settings
Equalizer, which requires
that the following is carried out beforehand:
1. Select a source by pressing one of the but-
tons (e.g. RADIO, MEDIA etc.). Continue
to press in order to scroll down among the
options on the TV screen (e.g.
FM1),
release and wait a second and the selec-
tion is accepted automatically. Alterna-
tively, turn TUNE and confirm with OK/
MENU.
2.
Press OK/MENU and turn TUNE, or use
the thumbwheel* on the steering wheel
keypad to reach the desired menu option
e.g.
Audio settings and press OK/
MENU.
3.
Turn TUNE again to reach the desired sub-
menu, e.g.
Equalizer, and press OK/
MENU.
Menus RADIO
Main menu AM
AM menu
Show presets
1
Scan
1
Only applies to High Performance Multimedia and Premium Sound Multimedia.
05 Infotainment system
Menu navigation, Infotainment
05
276
* Option/accessory, for more information, see Introduction.
Audio settings
2
Sound stage
3
Equalizer
4
Volume compensation
Reset all audio settings
Main menu FM1/FM2
FM menu
TP
Show radio text
Show presets
1
Scan
News settings
Advanced settings
REG
Alternative frequency
EON
Set TP favourite
PTY settings
Reset all FM settings
Audio settings
5
Main menu DAB1*/DAB2*
DAB menu
Ensemble learn
PTY filtering
Turn off PTY filtering
Show radio text
Show presets
1
Scan
Advanced settings
DAB linking
DAB band
Sub channels
Show PTY text
Reset all DAB settings
Audio settings
5
Menus MEDIA
Main menu CD Audio
Disc menu
Random
Scan
Audio settings
5
Main menu CD/DVD
1
Data
Disc menu
Play/Pause
Stop
Random
Repeat folder
Change subtitle
Change audio track
Scan
Audio settings
5
2
The menu options for audio settings are the same for all audio sources.
3
Only applies to Premium Sound Multimedia.
4
Does not apply to Performance.
1
Only applies to High Performance Multimedia and Premium Sound Multimedia.
5
For submenus, see "Main menu AM".
05 Infotainment system
Menu navigation, Infotainment
05
``
* Option/accessory, for more information, see Introduction.
277
Main menu DVD
1
Video
Disc menu
DVD disc menu
Play/Pause/Continue
Stop
Subtitles
Audio tracks
Advanced settings
Angle
DivX® VOD code
Audio settings
5
Main menu iPod
4
iPod menu
Random
Scan
Audio settings
5
Main menu USB
4
USB menu
Play/Pause
Stop
Random
Repeat folder
Select USB device
Change subtitle
Change audio track
Scan
Audio settings
5
Main menu Media Bluetooth
4
Bluetooth menu
Random
Change device
Remove Bluetooth device
Scan
Bluetooth software version in car
Audio settings
5
Main menu AUX
AUX menu
AUX input volume
Audio settings
5
Main menu TV*
TV menu
Select country
Reorganize presets
Autostore
Scan
Audio settings
5
Pop-up menu
6
video and TV*
Press OK/MENU when a video file is being
played back or TV* is being shown in order to
access the pop-up menu.
Image settings
1
Only applies to High Performance Multimedia and Premium Sound Multimedia.
5
For submenus, see "Main menu AM".
4
Does not apply to Performance.
6
Only applies when playing back videos or displaying TV*.
05 Infotainment system
Menu navigation, Infotainment
05
278
Source menu
7
DVD video menu
8
DVD disc TOP menu
8
Menus TEL
Main menu Bluetooth
handsfree
4
Phone menu
All calls
All calls
Missed calls
Answered calls
Dialled calls
Call duration
Phone book
Search
New contact
Speed dials
Receive vCard
Memory status
Clear phone book
Change phone
Remove Bluetooth device
Phone settings
Discoverable
Sounds and volume
Phonebook download
Bluetooth software version in
car
Call options
Auto answer
Voicemail number
Disconnect phone
7
What is shown in the pop-up menu for the source menu depends on what is being played back or displayed, it can be e.g. Disc menu or USB menu.
8
Only applies to DVD video discs.
4
Does not apply to Performance.

Related Topics

General information on infotainment Quick start General infotainment functions Radio Media player External audio source via AUX/USB* input Media Bluetooth?* TV* Remote control* Bluetooth? handsfree* Voice recognition* mobile phone RSE - Rear Seat Entertainment system* Menu navigation, Infotainment

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot