2025-2026 Volvo Xc70 SUV Maintenance and service -> Lamps User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Maintenance and service -> Lamps for Your Volvo Xc70 SUV Third Generation (2025-2026)

08 Maintenance and service
Lamps
08
331
General
All bulbs are specified, see page 336. The fol-
lowing list contains locations of bulbs and
other light sources that are specialised or
unsuitable for changing except at a workshop:
•
Active Xenon headlamps - ABL (Xenon
lamps)
•
Direction indicators, door mirrors
•
Approach lighting, door mirrors
•
Courtesy lighting
•
Glovebox lighting
•
General interior lighting in the roof
•
Reading lamps
•
Side position, position lamps rear
•
Brake light, Rear fog lamp, Reversing lamp
•
LED lights, general
WARNING
On cars with Xenon headlamps, the
replacement of Xenon lamps must be car-
ried out at a workshop - an authorised Volvo
workshop is recommended. Working with
Xenon lamps demands extreme caution
because the headlamp is equipped with a
high voltage unit.
IMPORTANT
Never touch the glass part of the bulbs with
your fingers. Grease and oils from your fin-
gers are vaporised by the heat, coating the
reflector and then causing damage.
Headlamps front
G010325
All of the headlamp bulbs are replaced via the
engine compartment. Loosen and remove the
whole headlamp.
WARNING
The remote control key must not be turned
to key position I or II during bulb replace-
ment.
See the section "Key positions" - for a
description of the remote control key's 3 key
positions.
Removing the headlamp
1. Make sure the remote control key is in key
position 0, see page 78:
2. (First illustration)
Pull out the headlamp's locking pins.
Pull the headlamp straight forward.
IMPORTANT
Do not pull the electrical cable, only the con-
nector.
3. (Second illustration)
Detach the headlamp connector by
pressing down the clip with your thumb.
At the same time, guide out the con-
nector with your other hand.
4. Lift out the headlamp and place it on a soft
surface to avoid scratching the lens.
08 Maintenance and service
Lamps
08
332
* Option/accessory, for more information, see Introduction.
5. Replace the bulb in question.
Securing the headlamp
1. Plug in the connector, a clicking sound
should be heard.
2. Reinstall the headlamp and locking pins.
Check that they are correctly inserted.
3. Check the lighting.
The headlamp must be mounted and the con-
nector correctly installed before the lighting is
switched on or the remote control key is
inserted into the ignition switch.
Removing the cover
G021745
Before starting to replace a bulb, see
page 331.
1. Open the lock clamp by pressing up/out.
2. Press down the clips on the cover and
remove it.
Reinstall the cover in reverse order.
Dipped beam, halogen
G021746
1. Detach the headlamp, see page 331.
2. Remove the cover.
3. Unplug the connector from the bulb.
4. Detach the bulb by pressing the holder
downwards.
5. Fit the new bulb in the socket and snap it
in. It can be secured in one position.
Reinstall the parts in reverse order.
08 Maintenance and service
Lamps
08
``
333
Main beam, Halogen
G021747
1. Detach the headlamp.
2. Remove the cover, see page 332
3. Detach the bulb by turning anticlockwise
and then pulling straight out
4. Unplug the connector from the bulb.
5. Replace the bulb and align it in the socket
and turn clockwise in order to secure it. It
can be secured in one position.
Reinstall the parts in reverse order.
Extra main beam, ABL headlamps*
G021748
1. Detach the headlamp.
2. Remove the cover, see page 332.
3. Detach the bulb by pressing the holder
downwards.
4. Unplug the connector from the bulb.
5. Fit the new bulb in the socket and snap it
in. It can only be secured in one position.
Reinstall the parts in reverse order.
Position/parking lamps
G021749
1. Detach the headlamp.
2. Remove the cover, see page 332.
3. For better access, detach the main beam
bulb first.
4. Pull the cable in order to withdraw the bulb
holder.
5. Remove the blown bulb and fit a new one.
It can only be secured in one position.
6. Fit the bulb holder in the socket and press
until a clicking sound is heard.
Reinstall the parts in reverse order.
08 Maintenance and service
Lamps
08
334
Direction indicators/flashers
G021750
1. Detach the headlamp.
2. Remove the small round cover.
3. Pull the bulb holder in order to extract the
bulb.
4. Remove the blown bulb and fit a new one.
It can only be installed in one way.
5. Fit the bulb holder in the socket and press
until a clicking sound is heard.
6. Refit the cover. It must be fitted and
pressed in until a clicking sound is heard.
Reinstall the parts in reverse order.
Side marker lamps
G021751
Before starting to replace a bulb, see
page 331.
1. Detach the headlamp.
2. Remove the small round cover.
3. Pull the cable in order to withdraw the bulb
holder.
4. Remove the blown bulb and fit a new one.
It can only be installed in one way.
5. Fit the bulb holder in the socket and press
until a clicking sound is heard.
6. Refit the cover. It must be fitted and
pressed in until a clicking sound is heard.
Reinstall the parts in reverse order.
Front fog lamps
1. Remove the cover by pressing in the 4 clips
with a thin blade and pulling straight out.
2. Unscrew the lamp housing screw and pull
it out.
3. Turn the bulb anticlockwise and remove it.
4. Fit a new bulb by turning clockwise.
5. Refit the bulb. (The profile of the bulb
holder corresponds to the profile of the
foot of the bulb).
6.
Refit the bulb holder. The TOP mark on the
bulb holder must always be upward.
08 Maintenance and service
Lamps
08
335
Lamp housing, rear
G017456
The direction indictor bulb in the rear lamp
cluster is replaced from inside the cargo area.
1. Open the panel.
2. Remove the insulation by pulling it straight
out.
3. Loosen the whole of the bulb by turning its
handle anticlockwise.
4. Detach the bulb by pulling it straight out.
NOTE
If an error message remains after the broken
bulb has been replaced then we recom-
mend that you visit an authorised Volvo
workshop.
Location of rear bulbs
G017457
Lamp lens, right-hand side
Position lamps/brake light (LED)
Side position lights (LED)
Direction indicators
Reflector, rear
Rear fog lamp (one side)
Reversing lamp
Brake light (LED)
Brake light (LED)
Number plate lighting
G017458
1. Remove the screws with a screwdriver.
2. Carefully detach the whole lamp housing
and withdraw it.
3. Replace the bulb.
4. Refit the whole lamp housing and screw it
into place.
08 Maintenance and service
Lamps
08
336
Lighting, cargo area
G031942
1. Insert a screwdriver and gently prize so
that the lamp housing comes loose.
2. Replace the bulb.
3. Check that the bulb illuminates and press
back the lamp housing.
Vanity mirror lighting
Removing the mirror glass
1. Insert a screwdriver in one of the two
recesses and carefully prize up the lug on
the edge.
2. Insert the screwdriver along the edge on
the left and right-hand sides and prize
carefully close to the black rubber sections
so that the mirror glass comes loose in the
lower edge.
3. Carefully detach and lift aside the entire
mirror glass and cover.
4. Replace the bulb.
Securing the mirror glass
1. Press the three lugs at top edge of the mir-
ror glass back into position.
2. Then press the three lower lugs back into
position.
Specification, bulbs
Lighting
W
A
Type
Dipped beam,
halogen
55 H7 LL
Main beam, Hal-
ogen
65 H9
Extra main beam,
ABL
55 H7 LL
Front direction
indicators
21 H21W LL
Position/parking
lamps front
5 W5W LL
Side marker
lamps front
5 W5W LL
Front fog lamps 35 H8
Direction indica-
tors side, door
mirrors
5 WY5W LL
Glovebox light-
ing
5 Socket SV8.5
Length 43 mm
08 Maintenance and service
Lamps
08
337
Lighting
W
A
Type
Vanity mirror
lighting
1.2 Socket SV5.5
Length 35 mm
Cargo area light-
ing
10 Socket SV8.5
Length 43 mm
Number plate
lighting
5 C5W LL
Direction indica-
tors, rear
21 PY21W LL
A
Watt

Related Topics

Popular Owner Manuals