Exterior lighting -> Replacing bulbs in LED headlights for Your Volkswagen Atlas SUV First Generation (2018-2023)

4. Turn off the turn signal if it is activated.  
5. Vehicles with an automatic transmission: Engage the parking lock  
6. Switch the ignition off.  
.
7. Allow the orientation lighting to turn off.  
8. Allow the affected light bulbs to cool down.  
9. Check if you can see that a fuse is burnt out   
Introduction.  
10. Change the affected light bulb according to the instructions ⇒  
.
A light bulb may only be replaced with the same type of light bulb. The respective name will be on the bulb socket or glass bulb.  
Never touch a glass light bulb with bare hands. The fingerprints left behind would vaporize from the heat when the bulb is switched on and condense on the  
reflector, which would then reduce the headlight brightness.  
11. Check the bulb function after a bulb is changed.  
If the bulb does not function, the bulb may not have been inserted correctly, may have fallen out, or the connector may not have been plugged in correctly.  
12. After every bulb replacement in the front of the vehicle, have the headlight adjustment checked by an authorized Volkswagen dealer or authorized Volkswagen  
Service Facility. Volkswagen recommends contacting an authorized Volkswagen dealer or authorized Volkswagen Service Facility.  
WARNING  
Failing to heed these instructions that are provided for your own safety can cause accidents and serious injuries.  
Always follow the activities in the instructions and follow the general safety precautions.  
NOTICE  
Removing and inserting trim panels and headlights incorrectly can damage the vehicle paint and body.  
When removing and inserting the headlight, be careful not to damage the vehicle paint and body.  
Replacing bulbs in LED headlights  
Please read the introductory information and heed the Warnings and Notice   
and Introduction.  
Preparations  
Only perform these activities in the specified order:  
1. Observe the information on bulb replacement and perform the activities.  
2. Open the hood.  
The headlight does not need to be removed for bulb replacement.  
Replacing a bulb in a turn signal  
Fig. 174 In the right-side of the engine compartment: Rear side of the headlights.  
Turn signal bulb holder cover.  
288  
Turn signal bulb holder.  
1. Remove the rubber cover fig. 174  
.
2. Pull out the lamp holder by the handle in the direction of the arrow fig. 174  
. At the same time, press the handle slightly up and down alternately, in order to  
aid removal.  
3. Replace the burned out bulb with a new bulb that is identical to the one being replaced.  
4. Carefully insert the lamp holder in the headlight and press it forwards until it perceptibly engages fig. 174  
5. Press around the circumference of the rubber cover.  
.
6. Close the hood.  
The figures show the right headlight. The left headlight is structured as its mirror image.  
Replacing bulbs in the vehicle body  
Please read the introductory information and heed the Warnings and Notice ⇒  
and Introduction.  
Preparations  
Only perform these activities in the specified order:  
1. Refer to the information on bulb replacement and carry out the activities.  
2. Open the trunk lid.  
3. Remove the taillight from the vehicle body.  
A screwdriver with the corresponding plug-in blade is required for removal.  
Replacing bulbs  
Fig. 175 Side of the luggage compartment: removing the taillight.  
Fuse for taillight connector.  
Connector for taillight.  
Fixing screw for taillight.  
Removing the taillight  
1. Use a screwdriver to lever off the ventilation grille at the recess and remove it in the direction of the arrow fig. 175.  
2. Remove the red locking mechanism fig. 175 on the connector.  
If necessary, use a suitable screwdriver to loosen the red locking mechanism.  
3. Release the connector fig. 175 and disconnect it.  
4. Remove the screw counterclockwise fig. 175  
.
5. Carefully pull the taillight toward the rear and out of the body.  
6. Remove the taillight and place it on a clean, flat surface.  
Replacing bulbs  
1. Turn the bulb holder counterclockwise until it stops and then remove it carefully from the taillight with the bulb.  
289