2007-2016 Volkswagen Tiguan 4 Door Power locking system User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Power locking system for Your Volkswagen Tiguan 4 Door First Generation (2007-2016)

Power locking system  
Introduction  
In this section you’ll find information about:  
Indicator light in the driver door  
Description of the power locking system  
Unlocking or locking the vehicle from the outside  
Unlocking or locking the vehicle from the inside  
Unlocking or locking the vehicle with Keyless Access  
Anti-theft alarm system  
The power locking system works properly only when all doors and the rear hatch are completely  
closed. When the driver door is open, the vehicle cannot be locked with the remote control vehicle key.  
For vehicles equipped with the Keyless Access with push button start, the vehicle can be locked only if  
the ignition is switched off and the driver door is closed.  
Leaving the vehicle unlocked for longer periods of non-use (for example, in your garage) can cause  
the vehicle battery to drain so that the engine can no longer be started.  
More information:  
Exterior views  
Volkswagen Information System  
Vehicle key set  
Doors  
Rear hatch  
Power windows  
Power sunroof  
Trailer towing  
Emergency closing and opening  
WARNING  
Improper use of power locks can result in serious personal injury.  
The power locking button locks all doors. Locking the doors from the inside can help  
prevent unintended door opening during a collision and can also prevent unwanted entry  
from the outside. Locked doors can, however, delay assistance to vehicle occupants and  
rescue from the outside in an accident or other emergency.  
Never leave children or anyone who cannot help themselves behind in the vehicle. All  
doors can be locked from the inside with the power lock button. This could leave people  
trapped in the vehicle in an emergency. Depending on the time of year, people trapped in the  
vehicle can be exposed to very high or very low temperatures.  
A closed vehicle can become very hot or very cold, depending on the season. Particularly  
in the summer, heat buildup in the passenger and luggage compartment of a parked vehicle  
can result in temperatures in the vehicle that are much higher than the outside temperatures.  
Temperatures can quickly reach levels that can cause unconsciousness and death,  
particularly to small children.  
Never allow passengers to remain in a locked vehicle. In an emergency any person still  
inside the vehicle might not be able to get out.  
Indicator light in the driver door  
Please first read and note the introductory information and heed the WARNINGS  
The indicator light for the power locking system is in the driver door ⇒ꢀ Passenger compartment.  
After the vehicle is locked  
Meaning  
The red LED light flashes for about 2 seconds in short  
intervals, then slower.  
The vehicle is locked.  
Red LED light flashes for about 2 seconds in short  
intervals, then lights up continuously for about  
30 seconds.  
Locking system malfunction. See an  
authorized Volkswagen dealer or an  
authorized Volkswagen Service Facility.  
NOTICE  
Failure to heed warning lights or text WARNINGS can result in vehicle damage.  
Description of the power locking system  
Please first read and note the introductory information and heed the WARNINGS  
The power locking system lets you unlock and lock all doors, the rear hatch, and the fuel filler flap:  
From the outside with the remote control vehicle key.  
From the outside with Keyless Access ⇒ꢀ Unlocking or locking the vehicle from the outside.  
From the inside with the power locking button  
Special functions of the power locking system can be activated or deactivated via the Convenience  
sub-menu in the Settingsmenu on vehicles with the Premium instrument cluster ⇒ꢀ Volkswagen  
Information System or by an authorized Volkswagen dealer or authorized Volkswagen Service Facility.  
The doors and the rear hatch can be locked manually if the remote control vehicle key or the power  
locking system is not working.  
Automatic locking (Auto lock)  
The vehicle will lock automatically when it reaches a speed of about 10 mph (15 km/h). When the  
vehicle is locked, the indicator light lights up in the power locking button ⇒ꢀfig. 28.  
Automatic unlocking (Auto unlock)  
All doors automatically unlock when you switch off the ignition and open a door from inside the vehicle.  
On vehicles with automatic transmission, the doors will also unlock when the selector lever is in Park  
(P) or the ignition is switched off. Auto unlock works only if the vehicle has been automatically locked  
with the Auto lock feature. The indicator light goes out in the power locking button when the doors  
unlock ⇒ꢀfig. 28.  
Locking the vehicle after airbag inflation  
If the airbags are activated during a collision, the entire vehicle is unlocked. Depending on the severity  
of the damage, the vehicle can be locked after a collision when the airbags have deployed as follows:  
Function  
Action  
Locking the vehicle with the  
power locking button:  
– Switch the ignition off.  
– Open a door once.  
– Press the power locking button .  
Locking the vehicle with the  
remote control vehicle key:  
– Switch the ignition off and on again  
OR: Remove the remote control vehicle from the ignition.  
– Open a door once.  
– Lock the vehicle with the remote control vehicle key.  
If the remote control vehicle key buttons ⇒ꢀ Vehicle key set or one of the power locking buttons  
Unlocking or locking the vehicle from the inside are pushed repeatedly in quick succession, the  
power locking system is switched off for a brief period to help keep it from being overloaded. The  
vehicle is then unlocked for about 30 seconds. Unless a door or the rear hatch is opened during this  
time, the vehicle is automatically locked afterwards.  
Unlocking or locking the vehicle from the outside  
Fig. 27 Remote control vehicle key with panic button.  
Please first read and note the introductory information and heed the WARNINGS  
Function  
Using the buttons on the remote control vehicle  
key buttons ⇒ꢀfig. 27  
Unlock the vehicle.  
Press the button. Keep pressed to unlock all doors  
and the rear hatch.  
Lock the vehicle.  
Press the button.  
Press the button.  
Unlock the rear hatch.  
Note: Depending on the settings for the power locking system in the Conveniencesub-menu on  
vehicles with the Premium instrument cluster, it may be necessary to press the button on the  
remote control vehicle key twice to unlock all doors and the rear hatch ⇒ꢀ Volkswagen Information  
System.  
The vehicle key unlocks or locks the vehicle only when the battery in the remote control key has  
enough power, and the remote control vehicle key is within a few yards/meters of the vehicle.  
All turn signals flash once and the horn beeps once to confirm that the vehicle has been locked.  
The horn beep can be disabled by deactivating the “ATA confirmation” feature in the Convenience  
submenu ⇒ꢀ Convenience sub-menu.  
All turn signals flash twice to confirm that the vehicle has been unlocked.  
If the turn signals do not flash to confirm locking, one or more doors, the rear hatch or the engine hood  
is not locked.  
If the driver door is open, the vehicle cannot be locked with the remote control vehicle key.  
If the vehicle was unlocked with the remote control vehicle key and the door or the rear hatch has not  
been opened in about 30 seconds, the vehicle is automatically locked again. This feature helps  
prevent you from leaving the vehicle unlocked unintentionally.  
Unlocking or locking the vehicle from the inside  
Fig. 28 On all 4 doors: Power locking button.  
Please first read and note the introductory information and heed the WARNINGS  
Press button ⇒ꢀfig. 28:  
Unlock the vehicle.  
Lock the vehicle.  
The power locking button works whether the ignition is switched on or off but only when all doors are  
closed.  
If the vehicle is locked with the remote control vehicle key, the power locking switch is deactivated.  
If the vehicle is locked with the power locking button:  
The yellow indicator light in the power locking button lights up ⇒ꢀfig. 28 to indicate that all doors  
and the rear hatch are locked.  
Opening doors or the rear hatch from the outside is not possible, at a traffic light, for example.  
Doors can be unlocked and opened separately from inside the vehicle by pulling the door handle to  
open the door. The indicator light goes out. The unopened doors and rear hatch remain locked and  
cannot be opened from the outside.  
An open driver door will not be locked. This helps keep the driver from being locked out of the  
vehicle.  
The vehicle is unlocked if you push the button while the vehicle is standing still. Depending on the  
settings in the Conveniencesubmenu ⇒ꢀ Convenience sub-menu, it may also be unlocked when you  
switch off the ignition and open a door from inside the vehicle (Auto unlock). On vehicles with  
automatic transmission, it may also be unlocked when the selector lever is in Park (P) and the ignition  
is switched off.  
Unlocking or locking the vehicle with Keyless Access  
Fig. 29 Ranges of the Keyless Access with push button start.  
Fig. 30 Keyless Access with push button start: Sensor 1 for unlocking on the inside of the front door handles.  
Sensor for locking 2 on the outside of the door handles.  
Please first read and note the introductory information and heed the WARNINGS  
Keyless Access is a keyless starting and locking system that unlocks and locks the vehicle without  
active use of a remote control vehicle key. All you have to do is touch a sensor surface on one of the  
front door handles ⇒ꢀfig. 29 or push the button on the rear hatch ⇒ꢀ Opening the rear hatch when a  
valid vehicle key is within range ⇒ꢀ  
.
General information  
When a valid vehicle key comes within range ⇒ꢀfig. 29, the Keyless Access with push button start  
recognizes a valid vehicle entry request as soon as a door handle sensor is touched on the driver or  
front passenger door or the button on the rear hatch is pressed. The following functions are then  
enabled without active use of the vehicle key:  
Keyless Entry: Unlocking the vehicle with the sensor surfaces on the door handles of the driver or  
front passenger door ⇒ꢀfig. 30 (1) or by using the button on the rear hatch.  
Keyless Go: Start the engine and drive. just have to press the starter button and a valid remote  
control vehicle key must be inside the vehicle.  
Keyless Exit: Locking the vehicle via the door handle of the driver or front passenger door (2).  
The power locks and the closing system work like the standard unlocking and locking system. Only the  
way that the systems are operated is different.  
All turn signals flash twice to confirm that the vehicle has been unlocked and once to confirm that it  
has been locked.  
If the vehicle was unlocked and within the next few seconds no door or the rear hatch has been  
opened, the vehicle is automatically locked again.  
Unlocking and opening doors (Keyless Entry)  
Grasp the door handle of the driver or front passenger door so that you touch the unlocking sensor  
surface (1).  
Open the door.  
Closing and locking doors (Keyless Exit)  
Close the driver door.  
Touch the sensor surface in the door handle on the driver or front passenger door (2) once. The  
vehicle is locked. The door being locked must be closed.  
Unlocking and locking the rear hatch  
If the vehicle is locked and if a valid vehicle key is within range ⇒ꢀfig. 29 of the rear hatch, it unlocks  
automatically when opened.  
Open and close the rear hatch as you would a standard rear hatch  
The rear hatch locks automatically when it is closed except in the following situations:  
The vehicle is completely unlocked.  
When an authorized vehicle key is inside the vehicle.  
Locking with a second vehicle key  
If a remote control vehicle key is inside the passenger compartment, the vehicle can be locked from  
the outside only if a second valid vehicle key is within range.  
When the vehicle is locked from the outside, the keyless go (starting) function of any keys left in the  
passenger compartment will be deactivated. All other functions (remote central locking and unlocking  
as well as emergency starting) remain active and unchanged.  
A key that was inside the vehicle when it was locked from the outside is reactivated:  
by pressing a button on the deactivated key.  
by pressing a door handle sensor when the deactivated key is outside of the vehicle, but within  
range.  
by starting the engine with the starter button on the center console.  
Automatic deactivation of sensors  
If the vehicle has not been unlocked or locked for a longer period of time, the proximity sensors in the  
passenger door are automatically deactivated.  
If a sensor on the door handle of a locked vehicle is activated too often, for instance by a bush or  
hedge that rubs against the vehicle, the sensors in the door handle on that side of the vehicle are  
switched off for about 30 minutes.  
The door handle sensors become active again if one of the following events occurs:  
30 minutes have passed.  
OR: The vehicle is unlocked using the button in the remote control vehicle key.  
OR: The rear hatch is opened.  
OR: The vehicle is mechanically unlocked with the vehicle key.  
Convenience features  
To use the convenience closing feature to close all power windows, hold your finger on the lock sensor  
surface ⇒ꢀfig. 30 (2) on the outside of the door handle for a few seconds until the windows close.  
Remove your finger from the lock sensor surface (2) to stop the function. If you touch the unlock  
sensor surface 1 on the inside of the door handle immediately after releasing the lock sensor surface 1  
(arrow), all of the windows will open (safety function). Pinch protection is active during convenience  
closing of the windows.  
The settings in the Settings – Conveniencemenu determine which doors open when the door  
handle sensor surface is touched.  
NOTICE  
The door handle sensor surfaces can be activated by a strong stream of water or steam if a  
valid vehicle key is within range of the vehicle.  
All windows may open if you turn the spray of water or steam away from and then back onto  
the door handle sensor surface in quick succession. If at least one power window is opened  
and the sensor is continuously activated, convenience closing is started.  
The door may not open if the outside and inside door handles are used at the same time.  
If the automatic transmission is not in Park (P) position, the electronic steering column lock will  
not lock and the vehicle will not lock via sensors in the front door handles or the remote control vehicle  
key.  
If the vehicle battery or the battery in the remote control vehicle key is weak or dead, it might not  
be possible to unlock and lock the vehicle using Keyless Access. The vehicle can still be manually  
locked or unlocked with the key bit  
The driver message Key not in rangeappears in the instrument cluster display if there is no  
remote control vehicle key inside the vehicle or if the system does not recognize the vehicle key. The  
key may not be recognized, for example, if it is covered by something that interferes with the signal  
(such as a briefcase), or if the remote control vehicle key battery is weak. Electronic devices such as  
mobile phones can also interfere with the signal.  
Dirt on the door handles that contains a lot of salt (especially in winter) can affect the way the  
door handle sensors work. Cleaning the door handles can help with this problem  
Anti-theft alarm system  
Please first read and note the introductory information and heed the WARNINGS  
Your vehicle is either equipped with an anti-theft alarm system or pre-equipped for anti-theft alarm  
system installation. If the vehicle is pre-equipped for installation of the anti-theft alarm system, the  
alarm system can be retrofitted by an authorized Volkswagen dealer or an authorized Volkswagen  
Service Facility.  
The anti-theft alarm system makes it more difficult for someone to break into or steal the vehicle.  
The anti-theft alarm system is automatically activated when the vehicle is locked by pressing the lock  
button on the remote control vehicle key.  
When is the alarm triggered?  
The anti-theft alarm system sounds for about 30 seconds and the turn signals flash for up to 5 minutes  
if the following occurs with respect to the locked vehicle:  
Opening a door that has been mechanically unlocked.  
Forcibly opening a door.  
Forcibly opening the engine hood.  
Forcibly opening the rear hatch.  
Switching on the ignition with an invalid key.  
Disconnecting the vehicle battery.  
Disconnecting an anti-theft system integrated trailer.  
Deactivating the alarm  
Unlock the vehicle with the unlock button on the remote control vehicle key and switch on the ignition  
with a valid remote control vehicle key.  
For vehicles with Keyless Access, the alarm can be deactivated by grasping one of the door handles  
when a valid vehicle key is in range or by holding the remote control vehicle key to the right of the  
steering column trim and pressing the starter button ⇒ꢀ Unlocking or locking the vehicle with Keyless  
Access.  
After the alarm has stopped and the vehicle is opened again in the same or a different area that  
is protected by the alarm, the alarm is triggered again. For example, the alarm will sound again if the  
rear hatch is opened after one of the doors has been opened.  
The anti-theft alarm system is not activated when the vehicle is locked with the power lock  
switch on the inside of the driver or front passenger doors.  
If the driver door is mechanically unlocked using the vehicle key bit, only the driver door is  
unlocked, but not the entire vehicle. Switching on the ignition deactivates the anti-theft alarm system  
and activates the central locking button. To unlock the doors, use the central locking button or remote  
control vehicle key.  
If the vehicle battery is dead or weak, the anti-theft alarm system will not work properly.  

Related Topics

Popular Owner Manuals