Get Trailer Hitch Guide for Audi A1 SUV 2010-2017

Audi A1 2011 ➤ , Audi A1 Sportback 2018 ➤ , Audi A2 2001 ➤ , Audi A3 20 ...

Electrical Equipment General Information - Edition 08.2019

2

Trailer Hitch

⇒ “2.1 Trailer Hitch Socket, Removing and Installing - Version 1”,

page 89

⇒ “2.2 Trailer Hitch Socket, Removing and Installing - Version 2”,

page 90

⇒ “2.3 Trailer Hitch Socket, Removing and Installing - Version 3”,

page 92

2.1

Trailer Hitch Socket, Removing and In‐

stalling - Version 1

Removing

– Turn off the ignition and remove the key.

– Remove the bolts -arrows-.

– Detach the socket from the retaining plate.

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not

permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability

with respect to the correctness of information in this document. Copyright by AUDI AG.

Socket with Rear Fog Lamp Shut-Off Contact Switch - F216- :

– Remove harness connector -2- for the Rear Fog Lamp Shut-

Off Contact Switch - F216- and harness connector -1- from the

Trailer Socket - U10- .

Socket without a Rear Fog Lamp Shut-Off Contact Switch -

F216- :

– Press multiple connector -1- in direction of -arrow- out of sock‐

et -2-.

2. Trailer Hitch

89

Audi A1 2011 ➤ , Audi A1 Sportback 2018 ➤ , Audi A2 2001 ➤ , Audi A3 20 ...

Electrical Equipment General Information - Edition 08.2019

Version 1

– Release securing tabs in direction of -arrows- and then release

retainer clips -1 and 3 through 5-.

– Remove the retainer from the connectors -2-.

Version 2

– First release securing tabs in direction of -arrows- and then

retaining clips -1, 2, 3, 4, 6, and 7-.

– Remove the retainer from the multi-pin connector -5-.

Installing

Install in reverse order of removal. Note the following:

Note

Make sure the O-rings -1 and 3- are not damaged.

– Slide the connectors -4- into the retainer -2- until they click into

place.

2.2

Trailer Hitch Socket, Removing and In‐

stalling - Version 2

Removing

Note

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not

permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability

with respect to the correctness of information in this document. Copyright by AUDI AG.

During installation, install the cable ties at the same location.

– Turn off the ignition and remove the key.

– Unfold and engage the trailer hitch.

– Cut the cable tie -1- and remove the screws -2 and 4-.

– Press the socket out of trailer hitch -3- in direction of -arrow-.

90

Rep. Gr.96 - Interior Lights, Lamps and Switches

Audi A1 2011 ➤ , Audi A1 Sportback 2018 ➤ , Audi A2 2001 ➤ , Audi A3 20 ...

Electrical Equipment General Information - Edition 08.2019

– Turn cap -1- counterclockwise -arrow- and remove it from

socket -3-.

– Remove rubber cover -2-.

– Release the retaining clips -arrows- and press multiple con‐

nector -2- out of socket -1-.

– Release the retaining clips -arrows- and remove retainer -1-

from multiple connector -3-.

Note

Carefully remove the retainer so that contacts -2- of the multiple

connector are not disconnected from the wiring harness.

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not

permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability

with respect to the correctness of information in this document. Copyright by AUDI AG.

2. Trailer Hitch

91

Audi A1 2011 ➤ , Audi A1 Sportback 2018 ➤ , Audi A2 2001 ➤ , Audi A3 20 ...

Electrical Equipment General Information - Edition 08.2019

Installing

Install in reverse order of removal. Note the following:

– The retainer -1- can be pushed onto multiple connector -3- in

only one position.

•

Guide pins -4- can be inserted into the retainer in only one

position. Contacts -2- must be inserted in the retainer for this

purpose.

– Insert the retainer into the multiple connector until it engages

audibly.

2.3

Trailer Hitch Socket, Removing and In‐

permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not

stalling - Ve_wrs_ithi_ro_esn_pec3_{t to the correctness of information in this document. Copyright by AUDI AG.}

Removing

– Fold out the trailer hitch. Refer to the vehicle Owner's Manual.

– Switch off the ignition and remove the ignition key.

– Remove the bolts -arrows-.

– Remove the socket from the retaining plate.

– Remove the rubber cover from the socket.

– Release the retaining clips in direction of -arrows- and press

multiple connector -1- out of socket -2-.

92

Rep. Gr.96 - Interior Lights, Lamps and Switches

Audi A1 2011 ➤ , Audi A1 Sportback 2018 ➤ , Audi A2 2001 ➤ , Audi A3 20 ...

Electrical Equipment General Information - Edition 08.2019

– Release the retaining clips in direction of -arrows- and remove

retainer -2- from multiple connector -3-.

Note

Carefully remove the retainer so that contacts -2- of the multiple

connector are not disconnected from the wiring harness.

Installing

Install in reverse order of removal. Note the following:

– The retainer -1- can be pushed onto multiple connector -3- in

only one position.

•

Guide pins -4- can be inserted into the retainer in only one

position. Contacts -2- must be inserted in the retainer for this

purpose.

– Insert the retainer into the multiple connector until it engages

audibly.

2.4

Trailer Hitch Socket, Removing and In‐

stalling - Version 4

Removing

Note

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not

During installation, install the cable ties at the same location.

permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability

with respect to the correctness of information in this document. Copyright by AUDI AG.

– Turn off the ignition and all electrical equipment.

– Move out the trailer hitch.

– Cut through the cable tie -3-.

– Remove the bolts -2-.

– Remove the socket from the trailer hitch -1-.

2. Trailer Hitch

93

Audi A1 2011 ➤ , Audi A1 Sportback 2018 ➤ , Audi A2 2001 ➤ , Audi A3 20 ...

Electrical Equipment General Information - Edition 08.2019

– Release the retainers -arrows-.

– At the same time remove the cap -1- from the socket.

– Remove rubber cover -2-.

– Release the clips in direction of -arrows- and press multiple

connector -2- out of socket -1-.

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not

permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability

with respect to the correctness of information in this document. Copyright by AUDI AG.

– Release the clips in direction of -arrows- and remove retainer

-1- from multiple connector -3-.

Note

Carefully remove the retainer so that contacts -2- of the multiple

connector are not disconnected from the wiring harness.

94

Rep. Gr.96 - Interior Lights, Lamps and Switches

Audi A1 2011 ➤ , Audi A1 Sportback 2018 ➤ , Audi A2 2001 ➤ , Audi A3 20 ...

Electrical Equipment General Information - Edition 08.2019

Installing

Install in reverse order of removal. Note the following:

– The retainer -1- can be pushed onto multiple connector -3- in

only one position.

•

Guide pins -4- can be inserted into the retainer -1- in only one

position. Contacts -2- must be inserted in the retainer for this

purpose.

– Insert the retainer into the multiple connector until it engages

audibly.

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not

permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability

with respect to the correctness of information in this document. Copyright by AUDI AG.

2. Trailer Hitch

95

Download User Manual App

Trailer Hitch for Your Audi A1 SUV 2010-2017

Related Topics

Wires

Popular Owner Manuals

Latest Owner Manuals