Get Driving information -> Acceleration measurement Guide for Audi A5 4 Door Third Generation (2025-2026)

Driving information

complete responsibility for safety in traffic. To

reduce the risk of an accident, only use the lap

timer functions in such a way that you always

maintain complete control over your vehicle in

all traffic situations.

Tips

– A maximum of 99 lap times can be meas-

ured.

– If timing is paused, you can continue it later

even if you turn off the ignition.

– Saved lap times cannot be individually de-

leted from the total results.

Tips

You can retrieve information from the trip

computer while the lap timer stopwatch is

running.

– The saved lap timer values will remain after

turning off the ignition.

Lap statistics

Applies to: vehicles with lap timer

Lap times and timing

Applies to: vehicles with lap timer

Displaying lap statistics

Requirement: the lap timer must be open.

You can display the number of laps driven , the

fastest lap +, the slowest lap , and the average

time ∅ in the instrument cluster.

Timing laps

►

To start timing manually, select Start lap 1 in

the menu.

►

Select in the instrument cluster: Vehicle func-

►

To start timing automatically as soon as you be-

tions tab >  button > Lap statistics.

gin to drive, select Start lap 1 by driving off or

Start by driving off in the menu.

►

Turn the thumbwheel down or up to display the

individual lap times.

►

To start timing a new lap after driving a lap, se-

►

To return to the lap timing that was started, se-

lect New lap in the menu. This starts timing

lect the  button > Lap times.

the next lap at the same time.

Resetting lap statistics

After completing a lap, the difference between

the last lap and the previous best lap time will be

indicated with a  or +.

Requirement: the lap statistics menu must be

displayed.

►

To reset the lap statistics, press and hold the

left thumbwheel until the message No lap

times have been recorded yet. appears.

Pausing timing and displaying a split time

►

To take a break , select Pause in the menu.

►

To resume timing, select Resume in the menu.

►

To display a split time, select Split time in the

Tips

menu. The split time  appears for approxi-

mately ten seconds in the instrument cluster.

The current lap timing will continue running.

The lap statistics list the lap times for the last

30 laps. The fastest and slowest lap times out

of up to 99 measured laps are also displayed.

Canceling lap timing

Acceleration

measurement

The timing of the current lap will stop. The lap

time will be erased and will not be included in the

statistics.

Introduction

Applies to: vehicles with acceleration measurement

►

Select Cancel lap in the menu.

Resetting the time

With the acceleration measurement, you can

measure the time that you need to reach a



►

Select Reset lap times in the menu.

Not available in all countries

137

Driving information

specific speed/distance. For the best possible

measurement readings, Audi recommends limit-

ing the ESC or turning it off. Keep in mind that

the environmental conditions and tire properties

can affect the results of the measurement.

ule (ITM). It replaces a separate transponder for

detecting toll fees. The system electronics are in-

tegrated in the rearview mirror housing.

To use the ITM in toll zones, you must register

and activate it.

Opening the acceleration measurement

Registration

►

Select in the instrument cluster: vehicle func-

►

Applies to: MMI: Select on the home screen:

tions tab >  button > Acceleration measure.

VEHICLE > Settings & Service > Integrated Toll

Module.

WARNING

►

Note the Integrated Toll Module ID.

Your focus should always be on driving your

vehicle safely. As the driver, you have com-

plete responsibility for safety in traffic. Only

use the acceleration measurement function

on closed courses to reduce the risk of acci-

dents.

►

To register the ITM, go to the displayed web ad-

dress and follow the instructions.

Activation

►

To activate the ITM, press  in the MMI.

Entering the number of passengers

Tips

A lower toll fee may be charged depending on the

number of passengers and the region. You must

either enter the number of passengers or deacti-

vate the ITM based on the laws applicable in the

area where you are driving.

The acceleration measurement was calibrated

using the largest possible summer tire/rim

combination available at the factory. Using a

different tire/rim combination could affect

the accuracy of the measurement.

►

To enter the number of passengers, select the

appropriate button in the MMI.

►

To deactivate the ITM, press  in the MMI.

Using the acceleration measurement

Applies to: vehicles with acceleration measurement

Tips

Requirement: the acceleration measurement

must be opened.

– The driver is responsible for specifying the

correct number of passengers and activat-

ing or deactivating the ITM.

►

Bring the vehicle to a full stop.

►

Select and confirm the desired speed or dis-

– Malfunctions can occur when detecting tolls

if both the ITM and transponder are activat-

ed. Deactivate the system not being used or

remove it as necessary.

tance.

►

Wait briefly until the  symbol appears in the

instrument cluster next to the time measure-

ment.

– If the rearview mirror is replaced, you must

ITM from the account.

►

To start the acceleration measurement, acceler-

ate the vehicle. The measurement ends auto-

matically once you have reached the selected

speed or distance.

– The system complies with United States FCC

regulations and ISED regulations

ðpage 310.

Integrated Toll Module

Display

Description

Applies to: vehicles with Integrated Toll Module

The selected number of passengers is displayed

in the MMI status bar ðpage 25.

Depending on the region, you can pay toll fees in

certain countries using the Integrated Toll Mod-



138

Driving information -> Acceleration measurement for Your Audi A5 4 Door Third Generation (2025-2026)

Related Topics

Popular Owner Manuals

Latest Owner Manuals