Get Phone Guide for Audi S Q5 SUV Third Generation (2025-2026)

Parking and maneuvering

1)

Exiting parking spaces with park assist

Applies to: vehicles with park assist

– Park assist is an assist system. The driver is

still responsible for monitoring the vehicle's

surroundings and preventing collisions

when using the system.

If you parked the vehicle in a parallel parking

space, park assist can help you drive out of it.

– When using park assist to drive into or out

of a parking space, the steering wheel turns

quickly on its own. Reaching into the steer-

ing wheel spokes while this is happening can

result in injury.

In the center display, arrows and symbols on the

vehicle roof 2 ðpage 183, fig. 143 indicate

what action is needed, such as applying the

brakes or changing the direction. Park assist au-

tomatically steers the vehicle out of the parking

space while the driver presses the pedals.

Note

►

Start the engine.

Press the  button in the center console.

Wait until a message appears in the center dis-

play that specifies the direction of travel re-

quired to exit the parking space.

Resume steering immediately after the last

corrective movement and the takeover

prompt, so that the specified steering wheel

angle is not recentered.

►

Activate the turn signal on the desired side or

press that side next to the vehicle in the center

display.

Interrupting the park assist

Applies to: vehicles with park assist

►

Activate the turn signal on the desired side or,

depending on vehicle equipment, press that

side next to the vehicle in the center display.

Park assist will be canceled automatically in the

following scenarios:

– You turn off the system.

– You start steering.

►

Make sure the actual direction the vehicle is

traveling matches the direction indicated by the

park assist.

Remove your hands from the steering wheel.

Pay attention to the path of the vehicle. If the

traffic situation permits, accelerate carefully

– The speed is too high.

– The time limit is exceeded.

– An obstacle is detected.

– ESC intervenes.

►

Actively resume control of the vehicle immediate-

ly, end the park assist manually, or:

ð

. The maximum speed for exiting a parking

space is 3 mph (5 km/h).

►

Follow the visual instructions in the display and

the audio warnings until the vehicle has finish-

ed exiting the parking space.

The process of exiting the parking space has

ended if additional corrective movements are

no longer necessary and the specified steering

wheel angle is sufficient to drive out of the

parking space. Actively take over steering im-

– You can resume the parking process in some

situations. Press the  button in the center

console.

– To continue exiting the parking space, turn the

engine off and on. Press the  button in the

center console.

WARNING

mediately ð

.

Observe the safety precautions and note the

limitations of the assist systems, sensors, and

cameras ðpage 139 to ðpage 142.

WARNING

– Observe the safety precautions and note the

limitations of the assist systems, sensors,

and cameras ðpage 139 to ðpage 142.

1)

In preparation at the time of printing.

186

Parking and maneuvering

Messages

Applies to: vehicles with park assist



If the

,

or  indicator light turns on, the

park assist is not available or was interrupted.

A message that indicates the cause and possible

solution may appear with some displays. The

weather conditions may be too poor or a sensor

may be obstructed. Clean the area in front of the

sensors ðpage 141 and try to turn the system on

again later.

If the malfunction remains, drive to an author-

ized Audi dealer or authorized Audi Service Facili-

ty immediately to have the malfunction correct-

ed.

187

Phone

Note

Read the information about Audi connect, es-

pecially regarding connectivity costs ð in

General information on page 200.

Introduction

Applies to: vehicles with phone

You can operate various phone functions easily

through the MMI in your vehicle.

Tips

Depending on the country and the vehicle equip-

ment, the following options may be available:

– The Bluetooth connection range is limited

to inside the vehicle.

– Connecting a mobile phone with Bluetooth

– Using two phones

– A selection of supported Bluetooth devices

can be found in the database for tested mo-

– Using the Audi phone box

WARNING

Setup

– Medical experts warn that mobile devices

can interfere with the function of pacemak-

ers. Always maintain a minimum distance of

about 7.9 inches (20 cm) between the mo-

bile device antennas and the pacemaker.

Connecting a mobile phone using

Bluetooth

Applies to: vehicles with phone

Requirement: the vehicle must be stationary and

the ignition must be turned on. The Bluetooth

settings must be open on your mobile device dur-

ing the connection setup. The mobile device to be

connected must not be actively connected to any

other Bluetooth device. The MMI must only be

connected to one mobile device.

– Do not carry the mobile device in a pocket

directly over the pacemaker when the

phone is turned on.

– Turn off the mobile device immediately if

you suspect it may be interfering with the

pacemaker.

– Do not use the voice recognition system*

ðpage 29 in emergencies because your

voice may change in stressful situations. The

system may take longer to dial the number

or may not be able to dial it at all. Dial the

emergency number manually.

►

Enable the Bluetooth function and visibility on

the MMI ðpage 242 and the mobile phone.

Applies to: MMI: Select on the home screen:

PHONE.

Follow the system instructions. The available

Bluetooth devices will be displayed after sever-

al seconds.

Press on the desired mobile device in the list of

displayed Bluetooth devices.

To update the list, press .

►

– Turn off your mobile device in areas where

there is a risk of an explosion. These loca-

tions are not always clearly marked. This

may include gas stations, fuel and chemical

storage facilities or transport vehicles, or lo-

cations where fuel vapors (such as propane

or gasoline vapor in vehicles or buildings),

chemicals or large quantities of dust parti-

cles (such as flour, sawdust or metal) may

be present in the air. This also applies to all

other locations where you would normally

turn off the vehicle drive system.

►

A PIN for a secure Bluetooth connection will be

generated.

►

Confirm the PIN on your mobile device.

Follow the system instructions.

Pay attention to any other system prompts on

the MMI and on your mobile phone.

►

After connecting successfully

– The demands of traffic require full attention

of all road users. Always read the chapter

ðpage 22, Information about traffic safety.

The mobile phone contacts are automatically

loaded in the MMI. This process can take several

minutes, depending on the number of contacts.



188

Phone

Depending on your mobile phone and the connec-

tion type, you can use the following functions:

can be reached in your vehicle through both mo-

bile phones.

Applies to: mobile devices with Bluetooth Mes-

sage Access Profile (MAP): You can send and re-

ceive messages with both mobile devices

ðpage 197.

Using the hands-free system

Requirement: your mobile phone must be con-

nected to the MMI via a Bluetooth Hands Free

Profile (Bluetooth HFP).

Connecting another mobile device

You can use the hands-free system. You can make

calls using the antenna on your mobile device.

Requirement: a mobile device must be connected

to the MMI. The vehicle must be stationary and

the ignition must be turned on. The Bluetooth

settings must be open on your mobile device dur-

ing the connection setup. The mobile device to be

connected must not be actively connected to any

other Bluetooth device.

Sending and receiving messages

See ðpage 197.

Tips

– Pay attention to any system prompts dis-

played on your mobile device or the MMI, for

example if the system should connect auto-

matically in the future. Depending on the

mobile device, you may need to download

contacts and confirm access to your mes-

sages separately.

►

Enable the Bluetooth function and visibility on

the MMI ðpage 242 and the mobile phone.

►

Applies to: MMI: Select on the home screen:

PHONE > , or

►

Applies to: MMI: Select on the home screen:

SETTINGS > Connected devices > Telephone 1

or Telephone 2 > New connection.

– You can also search for the MMI on your mo-

bile device using the Bluetooth device

search.

►

Follow the system instructions. The available

Bluetooth devices will be displayed after sever-

al seconds.

– You only have to pair your device one time.

Bluetooth devices that are already paired

automatically connect to the MMI when the

Bluetooth function is turned on, when they

are within range, and when the ignition is

turned on. The last connected mobile device

is given first priority.

►

Press on the desired mobile device in the list of

displayed Bluetooth devices.

►

To update the list, press .

A PIN for a secure Bluetooth connection will be

generated.

►

Confirm the PIN on your mobile device.

– You can manage additional settings for con-

nected mobile devices in the Connected de-

vices menu ðpage 243.

►

Follow the system instructions.

►

Pay attention to any other system prompts on

the MMI and on your mobile phone.

– When leaving the vehicle, the Bluetooth

connection to the mobile device will auto-

matically disconnect. Depending on your

mobile device, phone calls in progress may

be automatically redirected from the MMI to

your mobile device so that you can continue

the call on your phone.

After connecting successfully

See ðpage 188, After connecting successfully.

Switching between two mobile devices

Requirement: phone 1 and phone 2 must be con-

nected to the MMI.

►

Applies to: MMI: Select on the home screen:

PHONE > .

Using two phones

Applies to: vehicles with phone



You can connect two mobile phones to the MMI

at the same time using the Bluetooth HFP, for ex-

ample a business phone and a private phone. You

189

Phone

– The mobile device is inside a bag or a protective

case

Note

Read the information about Audi connect, es-

pecially regarding connectivity costs ð in

General information on page 200.

– There are objects between the Audi phone box

and the mobile device

– The mobile device is not positioned in the cen-

ter of the Audi phone box

Disconnecting a mobile device

Applies to: vehicles with phone

WARNING

– Loose objects can be thrown around the ve-

hicle interior during sudden driving or brak-

ing maneuvers, which increases the risk of

an accident. Store objects securely while

driving.

►

To disconnect a Bluetooth device from the MMI,

use the Connected devices menu ðpage 243.

Using the Audi phone

box

1)

– Do not allow the visual or audio signals from

a mobile device to distract you from traffic,

because this increases the risk of an acci-

dent. Operate the mobile device only via the

MMI. Move the Audi phone box under the

center armrest while driving.

General information

Applies to: vehicles with Audi phone box

Note

Applicable to U.S.A.

Operation of the Audi phone box is subject to

the following requirements of the Federal

Communications Commission:

– This is a CONSUMER device.

Fig. 144 Front center console: Audi phone box with con-

– BEFORE USE, you MUST REGISTER THIS DE-

VICE with your wireless provider and have

your provider´s consent. Most wireless pro-

viders consent to the use of signal boosters.

Some providers may not consent to the use

of this device on their network. If you are

unsure, contact your service provider.

– You MUST operate this device with approved

antennas and cables as specified by the

manufacturer. Antennas MUST be installed

at least 20 cm (8 inches) from any person.

– You MUST cease operating this device im-

mediately if requested by the FCC or a li-

censed wireless service provider.

nections

You can slide the Audi phone box forward over

the cup holder or back under the center armrest.

Depending on vehicle equipment, you may be

able to use the following functions with the Audi

phone box:

– Make phone calls using the vehicle’s exterior

antenna

– Charge a mobile device using the USB input

– Charge a mobile device wirelessly

– Reminder signal

Limitations

– WARNING: E911 location information may

not be provided or may be inaccurate for

calls served by using this device.

In some situations, the functions of the Audi

phone box may be limited or temporarily unavail-

able. For example, this may happen if:



– There is one more than mobile device in the

Audi phone box

1)

In certain countries.

190

Phone

Charging the battery using the USB input

Applies to: vehicles with Audi phone box

Note

Applicable to Canada

You can charge your mobile device using a special

USB adapter with the Audi phone box

ðpage 230.

In Canada, operation of a Zone Enhancer,

such as an Audi phone box, is subject to the

following requirements of the Innovation,

Science and Economic Development Canada

(ISED):

Requirement: the ignition must be turned on.

►

To charge your mobile device via USB, connect it

– This is a CONSUMER device.

to the USB input 1 ðpage 190, fig. 144.

– BEFORE USE, you MUST meet all require-

ments set out in CPC-2-1-05. At the time of

printing this user manual, the CPC-2-1-05

client procedures circular of ISED Canada

was available at the following web page:

nsf/eng/.

Tips

– You can purchase a USB adapter from an au-

thorized Audi dealer or authorized Audi

Service Facility, or at specialty stores.

– Audi recommends using Audi Genuine Ac-

cessories. Audi has verified their reliability,

safety, and suitability.

– You MUST operate this device with approved

antennas and cables as specified by the

manufacturer. Antennas MUST NOT be in-

stalled within 20 cm of any person.

– You MUST cease operating this device im-

mediately if requested by ISED or a licensed

wireless service provider.

Charging a mobile device wirelessly

Applies to: vehicles with Audi phone box

You can charge your mobile device wirelessly us-

ing the Audi phone box.

– WARNING: E911 location information may

not be provided or may be inaccurate for

calls served by using this device.

Requirement: the ignition must be turned on.

Your mobile device must meet the Qi standard.

►

Make sure that the wireless charging function

is turned on:

Applies to: MMI: Select on the home screen:

SETTINGS > General > Reminder signal and

mobile device charging.

Tips

The system complies with United States FCC

regulations and ISED regulations ðpage 322.

►

Making phone calls using the exterior

antenna

►

Turn on the Mobile device wireless charging

function.

To charge your mobile device wirelessly, lay it

Applies to: vehicles with Audi phone box

►

on the  symbol 3 ðpage 190, fig. 144 in the

center of the Audi phone box with the display

facing up.

With the Audi phone box, you can make calls us-

ing the exterior antenna on the vehicle. Using the

exterior antenna helps when there is a low signal

and also provides better reception quality.

WARNING

Requirement: the ignition must be turned on.

– The mobile device may become hot during

wireless charging. Pay attention to the tem-

perature of your mobile device and be care-

ful when removing it from the Audi phone

box.

►

To make phone calls through the vehicle's exte-

rior antenna using your mobile device, lay your

device on the phone symbol 2 ðpage 190,

fig. 144 in the center of the Audi phone box

with the display facing up.

– An alternating magnetic field is used for

wireless charging. Maintain a minimum dis-

tance of approximately 2.4 inches (6 cm) to



191

Phone

Mobile device notes: reminder, charge level

the Audi phone box charging plate. The

thresholds for prolonged exposure at this

distance comply with ICNIRP1998. There-

fore, interactions such as irritation of senso-

ry organs, malfunctions of active medical

implants (such as pacemakers, infusion

pumps, or neurostimulators) or effects on

passive medical implants (such as prosthetic

limbs) is highly unlikely. If you have a medi-

cal implant, seek medical advice from a spe-

cialist if you have any questions. You can al-

so turn the function for wireless charging in

the Audi phone box on or off. You can still

charge your mobile device using a cable con-

nection.

When this function is turned on, the charge sta-

tus of your mobile device is displayed. You will al-

so be reminded not to forget your mobile device

when leaving the vehicle.

Using the phone

Accessing phone functions

Applies to: vehicles with phone

Tips

– The maximum charging capacity is 5 W.

– The charging time and temperature will vary

depending on the mobile device being used.

Fig. 145 Center display: selection menu

Requirement: a mobile device must be connected

to the MMI.

Mobile device reminder signal

►

Applies to: MMI: Select on the home screen:

Applies to: vehicles with Audi phone box

PHONE.

When the device reminder signal is turned on,

you will be notified that your mobile device is still

in the Audi phone box when you leave the vehicle.

Possible phone functions:

1

2

3

4

5

6

7

Search

Call list . . . . . . . . . . . . . . . . . . . . . .

Favorites . . . . . . . . . . . . . . . . . . . . .

Contacts . . . . . . . . . . . . . . . . . . . . .

Voicemail . . . . . . . . . . . . . . . . . . . .

Dial phone number . . . . . . . . . . . .

Switch telephones . . . . . . . . . . . . .

192

193

194

196

Requirement: your mobile device must be locat-

ed in the Audi phone box (if Qi-capable) or con-

nected to the USB port with charging function us-

ing a USB adapter, and the smartphone interface

must be active or your iPhone must be connected

to the MMI via Bluetooth and charging using a

USB adapter connected to the USB port with

charging function.

Managing call lists

Applies to: vehicles with phone

►

Applies to: MMI: Select on the home screen:

SETTINGS > General > Reminder signal and

mobile device charging.

The following settings may be available, depend-

ing on vehicle equipment:

– Signal tone

– Off

Fig. 146 Center display: call list



Spoken cue

This setting is turned on at the factory.

192

Phone

Opening call lists using the MMI

Accessing favorites

►

Applies to: MMI: Select on the home screen:

PHONE > Call list.

PHONE > Favorites.

Opening call lists using the multifunction

steering wheel

Storing favorites

►

Press  ðpage 194 in the business card, or

►

Select in the instrument cluster: Phone tab > 

►

Press Store as favorite in the options

button > Call list.

ðpage 192.

Possible call list symbols:

Deleting favorites

1

2

3

4

5

6

Missed calls

►

Press  ðpage 194 in the business card, or

Select: Favorites >  > one or multiple favor-

ites or Select all > Delete > (Done).

Dialed numbers

►

Accepted calls

Editing a phone number

Display business card . . . . . . . . . . .

Tips

194

Number of interactions with a con-

tact

The favorites can only be edited via the MMI.

Managing the directory

Applies to: vehicles with phone

If more than one interaction with a contact or

number has taken place, the last one is displayed

in the form of an arrow 1 , 2 , or 3 .

You can manage up to four directories in the

MMI.

Call list options

Requirement: a mobile device must be connected

to the MMI.

Press and hold a contact or a phone number in

the list until the Options menu appears.

Opening the directory

Depending on the vehicle equipment and your

mobile phone, the following options may be

available:

►

Applies to: MMI: Select on the home screen:

PHONE > Contacts.

– Store as favorite ðpage 193.

– Send a text ðpage 197.

– Send e-mail ðpage 197.

The contacts will be displayed. You can change

the sort order ðpage 196, Sort order.

Deleting imported contacts

Edit number

Requirement: you must have imported at least

one contact ðpage 196.

Edit a phone number before dialing it.

Show history

►

Select: Contacts >  > one or more text mes-

sages > Delete > (Done). The imported contacts

are deleted.

Requirement: you must have had more than one

interaction with a contact.

All interactions with a contact or a number are

displayed.

Directory options

►

Press and hold a contact in the directory until

the Options menu appears.

Managing favorites

Depending on the vehicle equipment and your

mobile phone, the following options may be

available:

Applies to: vehicles with phone

You can store contacts for all connected mobile

devices as shortcuts in the favorites list.

– Store as favorite ðpage 193.



193

Phone

– Send contact: you can select Text message or

E-mail ðpage 197.

Listening to voicemail

Applies to: vehicles with phone

– Send a text ðpage 197.

Calling voicemail

– Send e-mail ðpage 197.

►

Applies to: MMI: Select on the home screen:

PHONE > Voicemail.

Tips

– Pay attention to any synchronization

prompts on your mobile device when down-

loading contacts.

Entering the voicemail number

Requirement: there must be no voicemail num-

ber stored.

– The contacts from the mobile device may

not be transferred in alphabetical order. If

there are too many entries, contacts with

different first letters may be missing in the

MMI.

►

Enter the desired number.

►

Press OK.

Dialing the voicemail number

– Only the contacts from the active connected

mobile device are displayed.

Requirement: a voicemail number must be stor-

ed.

– The contacts in the local MMI memory are

always visible and can be accessed by other

persons.

►

Press Voicemail. The call begins immediately.

Tips

– After turning off the ignition and exiting the

vehicle, the mobile device directory will be

updated when the MMI is started again if

the mobile device is within range and the

Bluetooth function is turned on in the mo-

bile device and the MMI.

This service must be set up and activated by

the mobile phone service provider.

Dialing a phone number

Applies to: vehicles with phone

– Only the contacts in the local MMI memory

can be deleted.

Depending on the vehicle equipment, you may

have the following options for dialing a phone

number:

Opening business cards

Applies to: vehicles with phone

– Using text input in the MMI ðpage 26.

– Using voice operation ðpage 29.

The business card shows you details about a con-

tact.

Call options

►

Applies to: vehicles with phone

To open a business card, press on a contact in

the directory, or

Press  in the call list 5 ðpage 192, fig. 146.

►

To accept or end a call, press the  button on

the multifunction steering wheel.

►

Possible options in the business card:

Depending on your mobile device, the following

options may be available in the MMI when there

is an incoming call:

►

Call: press on a phone number.

►

Storing a favorite: press .

►

Deleting a favorite: press .

►

Sending a text message: press .

Starting navigation: press on an address.

Sending an e-mail: press on an e-mail address.

Send contact: you can select Text message or

– Answer

– Decline

– Message

►

If you exit the vehicle during a phone call, the

Bluetooth connection will be disconnected. De-

pending on your mobile device, phone calls in

E-mail ðpage 197.



194

Phone

Swapping a call

progress may be automatically transferred from

the MMI to your mobile device.

Requirement: Conference ðpage 196 must be

turned on. Two phone calls must be in progress.

Tips

You can alternate between two phone calls.

The radio or media playback is muted during a

phone call.

Additional call options

Press More.

During a phone call

Depending on the mobile device being used and

the type of connection, the following options

may be available:

Applies to: vehicles with phone

Depending on your mobile device and the type of

connection, the following options may be availa-

ble during a call:

Transfer call to mobile device

Transfer the current call to your mobile device or

Bluetooth headset*.

– End call

– Mute

Switch to hands-free

Sending a tone sequence

Transfer the current call from your mobile device

to the MMI.

Press Numbers. You can enter tone sequences

(DTMF) and send them to the other party on the

call.

Add call

Hold

You can start a new call. The current call will be

put on hold.

Requirement: Conference ðpage 196 must be

turned on.

Remove conference member

Puts the current call on hold. To resume the call,

press Resume.

You can remove conference call members individ-

ually when a conference call is active.

Answering an incoming call

Microph. input

One of these options will be available, depending

on your mobile phone service provider and the se-

lected Conference setting ðpage 196:

You can adjust the input level of the microphone

using the slider.

– Answer: the current phone call will be put on

hold. The incoming call will be answered.

– Replace: the active call will be replaced with

the incoming call.

Tips

The call waiting function must be activated in

your mobile device to be alerted about an in-

coming call during an active call.

Declining an incoming call

Making an emergency call

Applies to: vehicles with phone

If you select Decline, the incoming call will be de-

clined.

Requirement: a mobile device must be connected

to the MMI.

Conference

Requirement: Conference ðpage 196 must be

turned on. Two phone calls must be in progress.

►

Applies to: MMI: Select on the home screen:

PHONE > Dial phone number > the local emer-

gency call number (for example, 911) > Dial.

Depending on your mobile phone service provid-

er, you can add a call on hold and up to five active

callers to a conference call.



195

Phone

– Microphone input level: you can adjust the in-

put level of the microphone using the slider.

WARNING

– Because your phone works with radio sig-

nals, a connection cannot be guaranteed un-

der all circumstances. Do not rely on only

your phone when it comes to essential com-

munication (such as during a medical emer-

gency).

Data module serial number (IMEI)

Applies to: vehicles with data module

The serial number (IMEI) will be displayed.

Contact settings

Applies to: vehicles with phone

– Always follow the instructions given by the

emergency personnel during an emergency

call and only end the call when they instruct

you to do so.

►

Applies to: MMI: Select on the home screen:

PHONE > Contacts > .

Switching between two mobile devices

Settings

Requirement: phone 1 and phone 2 must be con-

nected to the MMI.

Phone settings

Applies to: vehicles with phone

Switch telephones: the device name of the avail-

able mobile device is displayed. You can switch

the phone by pressing the button.

►

Applies to: MMI: Select on the home screen:

PHONE > .

The directory for the selected phone will be dis-

played.

The following options may be possible, depend-

ing on your mobile device:

Hide grayed-out contacts

– Decline with text message

– Edit voicemail number

When this function is turned on, contacts that

have no phone numbers stored for them will be

hidden.

Switching between two mobile devices

Requirement: phone 1 and phone 2 must be con-

nected to the MMI.

Sort order

You can sort the contacts by Last name or First

name.

Switch telephones: the device name of the avail-

able mobile device is displayed. You can switch

the phone by pressing the button.

Download contacts

Conference

Requirement: a mobile device must be connected

to the MMI.

Depending on your mobile phone service provid-

er, you can use the following functions when the

conference function is turned on:

To update the contacts in the MMI, you can man-

ually download your mobile device contacts. De-

pending on the mobile device, you may need to

disconnect and reconnect the Bluetooth connec-

tion to update the contacts.

– Accept another call while on a call. The first

phone call is put on hold.

– Put an existing phone call on hold and start an-

other call.

Importing and exporting contacts

– Merge two phone calls into one conference call.

Requirement: a USB storage device is connected

to a USB port with charging function ðpage 230. 

Ringtone and volume settings

– Ringtone and message volume: you can adjust

the volume using the slider.

– Ringtone: select a ringtone from the list.

196

Phone

If necessary, user-defined folders will be copied

Contacts in vCard format (.vcf) can be imported

or exported from the MMI.

to your mobile device.

– Importing contacts from a storage device: Re-

quirement: the USB storage device must con-

tain contacts in the vCard format. They must

not be located in sub-folders. Select: > Search

for import data > USB device 1/USB device 2 >

desired contacts or Select all > Start import.

– Exporting contacts to a storage medium: Re-

quirement: you must have a contact imported.

Select: Export contacts > Find exporting

Message options

Press on a text message.

Depending on the country, the following options

may be available:

– Read out

– Reply

– Forward

– More

source > USB device 1/USB device 2 > desired

contacts or Select all > Start export.

To switch between messages, press  or .

Press More. Depending on your mobile device

and the selected mailbox, additional options may

be available:

Tips

– The imported contacts are stored in the lo-

cal MMI memory.

– Call

– There should be no other files or folders on

the storage medium containing the contacts

to be imported.

– Forward

– Navigate

– Extract numbers

– Send again

– Contacts that were downloaded from a mo-

bile device cannot be exported.

– Apple devices and MTP devices (such as

smartphones) are not recognized as USB

storage devices.

Settings

Press .

New text message notification

Messages

When the function is turned on, an envelope 

in the MMI status bar will indicate when there is a

new text message.

Text messages

Applies to: vehicles with phone

Requirement: your mobile device must be con-

nected to the MMI via Bluetooth Message Access

Profile (Bluetooth MAP).

Tips

Only new received messages may be displayed

depending on your mobile device.

►

Applies to: MMI: Select on the home screen:

MESSAGES > () > Text message (phone 1)/

Text message (phone 2).

E-mail

Applies to: vehicles with phone and e-mail

Requirement: your mobile device must be con-

nected to the MMI via Bluetooth Message Access

Profile (Bluetooth MAP).

The following functions are available:

– New text message*

– Inbox

►

Applies to: MMI: Select on the home screen:

– Sent

MESSAGES > () > E-mail (phone 1)/E-mail

(phone 2).

– Outbox*

– Drafts*

– Deleted

The following functions are available:

User defined*

– New e-mail

– Inbox



197

Phone for Your Audi S Q5 SUV Third Generation (2025-2026)

Related Topics

Popular Owner Manuals

Latest Owner Manuals