Get Interior equipment -> Universal Integrated Remote Control Guide for BMW X6 4 Door Second Generation (2015-2019)

Interior equipment

Controls

Interior equipment

the safety instructions of the hand-held trans‐

mitter.◀

Vehicle features and options

This chapter describes all standard, country-

specific and optional features offered with the

series. It also describes features that are not

necessarily available in your vehicle, e. g., due

to the selected options or country versions.

This also applies to safety-related functions

and systems. When using these functions and

systems, the applicable laws and regulations

must be observed.

Compatibility

If this symbol is printed on the packag‐

ing or in the owner's manual of the sys‐

tem to be controlled, the system is

generally compatible with the integrated Uni‐

versal Remote Control.

If you have any questions, please contact:

▷

A dealer’s service center or another quali‐

fied service center or repair shop.

Universal Integrated Remote

Control

▷

on the Internet.

HomeLink is a registered trademark of Gentex

Corporation.

Concept

The integrated Universal Remote Control in

the interior mirror can operate up to 3 func‐

tions of remote-controlled systems, such as

garage door drives, barriers, or lighting sys‐

tems. The Integrated Universal Remote Con‐

trol replaces up to 3 different hand-held trans‐

mitters. To operate the remote control, the

buttons on the interior mirror must be pro‐

grammed with the desired functions. The

hand-held transmitter for the particular system

is required in order to program the remote con‐

trol.

Control elements on the interior mirror

▷

LED, arrow 1.

Before selling the vehicle, delete the stored

functions for the sake of security.

Buttons, arrow 2.

The hand-held transmitter, arrow 3, is re‐

quired for programming.

Safety information

WARNING

Programming

Body parts can be jammed when operat‐

ing remote-controlled systems, for instance

the garage door, using the integrated Universal

Remote Control. There is a risk of injury or risk

of damage to property. Make sure that the area

of movement of the respective system is clear

during programming and operation. Also follow

General information

1. Switch on the ignition.

2. Initial setup:

Press and hold the two outer buttons on

the interior mirror simultaneously for ap‐

183

Controls

Interior equipment

proximately 20 seconds until the LED on

the interior mirror flashes. This erases all

programming of the buttons on the interior

mirror.

flashing rapidly and then stays lit constantly for

2 seconds, the system features a rolling code

radio system. Flashing and continuous illumi‐

nation of the LED will repeat for approximately

20 seconds.

3. Hold the hand-held transmitter for the sys‐

tem to be controlled approx. 1 to 3 in‐

ches/2.5 to 8 cm away from the buttons of

the interior mirror. The required distance

depends on the hand-held transmitter.

For systems with a rolling code radio system,

the integrated Universal Remote Control and

the system also have to be synchronized.

Please read the owner's manual to find out

how to synchronize the system.

4. Simultaneously press and hold the button

of the desired function on the hand-held

transmitter and the button to be program‐

med on the interior mirror. The LED on the

interior mirror will begin flashing slowly.

Synchronizing is easier with the aid of a sec‐

ond person.

Synchronizing the universal remote control

with the system:

5. Release both buttons as soon as the LED

flashes more rapidly. The LED flashing

faster indicates that the button on the inte‐

rior mirror has been programmed.

1. Park the vehicle within range of the re‐

mote-controlled system.

2. Program the desired button on the interior

mirror as described.

If the LED does not flash faster after at

least 60 seconds, change the distance be‐

tween the interior mirror and the hand-held

transmitter and repeat the step. Several

more attempts at different distances may

be necessary. Wait at least 15 seconds be‐

tween attempts.

3. Locate and press the synchronizing button

on the system being programmed. You

have approx. 30 seconds for the next step.

4. Hold down the programmed button on the

interior mirror for approximately 3 seconds

and then release it. If necessary, repeat this

step up to three times in order to finish

synchronization. Once synchronization is

complete, the programmed function will be

carried out.

Canada: if programming with the hand-

held transmitter was interrupted, hold

down the interior mirror button and repeat‐

edly press and release the hand-held

transmitter button for 2 seconds.

Reprogramming individual buttons

1. Switch on the ignition.

6. To program other functions on other but‐

tons, repeat steps 3 to 5.

The systems can be controlled using the inte‐

rior mirror buttons.

2. Press and hold the interior mirror button to

be programmed.

3. As soon as the interior mirror LED starts

flashing slowly, hold the hand-held trans‐

mitter for the system to be controlled ap‐

prox. 1 to 3 inches/2.5 to 8 cm away from

the buttons of the interior mirror. The re‐

quired distance depends on the hand-held

transmitter.

Special feature of the rolling code

wireless system

If you are unable to operate the system after

repeated programming, please check if the

system to be controlled features a rolling code

radio system.

Read the system's owner's manual, or press

the programmed button on the interior mirror

longer. If the LED on the interior mirror starts

184

Interior equipment

Controls

4. Likewise, press and hold the button of the

desired function on the hand-held trans‐

mitter.

hold the two outer buttons on the interior mir‐

ror simultaneously for approximately 20 sec‐

onds until the LED on the interior mirror

flashes rapidly.

5. Release both buttons as soon as the inte‐

rior mirror LED flashes more rapidly. The

LED flashing faster indicates that the but‐

ton on the interior mirror has been pro‐

grammed. The system can then be con‐

trolled by the button on the interior mirror.

Sun visor

Glare shield

Fold the sun visor down or up.

If the LED does not flash faster after at

most 60 seconds, change the distance and

repeat the programming starting with

step 4. Several more attempts at different

distances may be necessary. Wait at least

15 seconds between attempts.

Glare shield from the side

Folding out

1. Fold the sun visor down.

Canada: if programming with the hand-

held transmitter was interrupted, hold

down the interior mirror button and repeat‐

edly press and release the hand-held

transmitter button for 2 seconds.

2. Unhook it from the holder and swing it to

the side.

3. Move it back to the desired position.

Folding up

Proceed in the reverse order to close the sun

visor.

Operation

WARNING

Body parts can be jammed when operat‐

ing remote-controlled systems, for instance

the garage door, using the integrated Universal

Remote Control. There is a risk of injury or risk

of damage to property. Make sure that the area

of movement of the respective system is clear

during programming and operation. Also follow

the safety instructions of the hand-held trans‐

mitter.◀

Vanity mirror

A vanity mirror is located in the sun visor be‐

hind a cover. When the cover is opened, the

mirror lighting switches on.

Ashtray

Opening

The system, such as the garage door, can be

operated using the button on the interior mirror

while the engine is running or when the ignition

is started. To do this, hold down the button

within receiving range of the system until the

function is activated. The interior mirror LED

stays lit while the wireless signal is being

transmitted.

Deleting stored functions

All stored functions will be deleted. The func‐

tions cannot be deleted individually. Press and

Slide the cover forward.

185

Interior equipment -> Universal Integrated Remote Control for Your BMW X6 4 Door Second Generation (2015-2019)

Related Topics

Interior equipment

Popular Owner Manuals

Latest Owner Manuals