Get Access Guide for Citroen Ds5 SUV First Generation (2011-2018)

002

Access

Electronic key

remote control

Unlocking the vehicle

complete unlocking

Selective unlocking

F

To unlock only the driver's door,

F

Press the open padlock to

press the open padlock once.

completely unlock the vehicle.

F

To unlock the other doors and

the boot, press the open padlock

again.

System which permits central unlocking or

locking of the vehicle using the lock or from a

distance. It is also used to locate and start the

vehicle, as well as providing protection against

theft.

This setting is done in the vehicle

configuration menu.

Complete unlocking is activated by

default.

Unlocking is confirmed by rapid flashing

of the direction indicators for around

two seconds.

At the same time, depending on

version, the door mirrors unfold.

53

Access

Selective boot unlocking

Locking the vehicle

F

Press the closed padlock to fully

lock the vehicle.

Hold the button down until the

windows close completely.

If one of the doors or the boot is not fully

F

Press this button until you hear

the boot unlock. The doors

remain locked.

closed, locking does not take place.

When the vehicle is locked, if it

is unlocked inadvertently, it will

automatically lock itself again after

about thirty seconds unless a door is

opened.

F

If selective boot unlocking is

deactivated, pressing this button

unlocks the whole vehicle.

If the alarm was previously activated, it

will not be reactivated automatically.

Locking is confirmed by fixed

illumination of the direction indicators

for approximately two seconds.

Depending on version, the door mirrors

fold at the same time.

The selective boot unlocking function

is set in the vehicle configuration

menu.

By default, selective boot unlocking

is on.

Be particularly aware of children when

operating the windows.

Keyless Entry and Starting

Unlocking the vehicle

complete unlocking

Selective unlocking

F

To unlock only the drivers door, with the

electronic key on your person, pass your

hand behind the driver's door handle.

F

To unlock the complete vehicle, pass your

hand behind one of the passenger door

handles on the same side of the vehicle as

the electronic key is located.

System that allows the unlocking, locking

and starting of the vehicle while keeping the

electronic key on your person.

This setting is done via the vehicle

configuration menu.

By default, complete unlocking is

activated.

F

With the electronic key on your person and

in the recognition zone A, pass your hand

behind one of the door handles to unlock

the vehicle.

It can also be used as a remote control.

For more information, refer to the

"Electronic key / remote control" section.

Your passengers can also open their doors, as

soon as the electronic key is in the recognition

zone.

Unlocking is confirmed by rapid

flashing of the direction indicators for

approximately two seconds.

The door mirrors unfold at the same

time.

If the alarm is on, the audible warning

triggered when opening a door with the

key (integral with the remote control), will

stop when the ignition is switched on.

For reasons of safety and theft protection,

do not leave your electronic key in the

vehicle, even when you are close to it.

It is recommended that you keep it on

your person.

55

Access

Locking the vehicle

Locating your vehicle

This function allows you to identify

your vehicle from a distance,

particularly in poor light. Your vehicle

must be locked.

Ensure that nothing and no person

prevents the correct operation of the

windows.

Be particularly aware of children when

operating the windows.

F

Press the closed padlock on the remote

control.

This will switch on the courtesy lamps and

the direction indicators will flash for around

ten seconds.

If one of the doors or the boot is still

open or if the key for Keyless Entry and

Starting system has been left inside

the vehicle or if the ignition is on, the

central locking does not take place.

When the vehicle is locked, if it is

unlocked inadvertently, it will lock itself

again automatically after about thirty

seconds unless a door is opened.

If the alarm was previously activated, it

will not be reactivated automatically.

The folding and unfolding of the door

mirrors by the remote control can be

deactivated by a CITROËN dealer or a

qualified workshop.

As a safety measure (children on

board), never leave the vehicle without

taking the key for the Keyless Entry and

Starting system, even for a short period.

Guard against theft when the key for the

Keyless Entry and Starting system is

in the recognition zone with the vehicle

unlocked.

In order to preserve the charge of the

cell battery in the remote control, the

"hands-free" functions go into extended

stand-by after 21 days of non-use. To

restore these functions, press one of

the remote control buttons or start the

engine with the electronic key in the

reader.

F

With the electronic key on your person in

the recognition zone A, press with a finger

or thumb on one of the door handles (at the

markings) to lock the vehicle.

Maintain pressure with your finger or thumb

until the windows close completely.

Locking is confirmed by fixed

lighting of the direction indicators for

approximately two seconds.

The door mirrors fold at the same time.

deadlocking

Using the remote control

With Keyless Entry and

Starting

Deadlocking renders the exterior and

interior door controls inoperative.

It also deactivates the manual central

locking button.

You must therefore never leave

anyone inside the vehicle when it is

deadlocked.

F

Press the closed padlock to lock

the vehicle completely.

Maintain pressure with your finger to

close the windows.

F

Press the closed padlock again within

five seconds to deadlock the vehicle.

Ensure that nothing or any person

prevents the correct closing of the

windows.

Be particularly aware of children when

operating the windows.

By the doors:

F

With the electronic key on your person

in the recognition zone A, press with a

finger or thumb on the door handle (at the

markings) to lock the vehicle.

F

Within five seconds, press the door handle

again to deadlock the vehicle.

57

Access

Back-up key

Unlocking / Locking using the integral key with Keyless

Entry and Starting

The integral key is used to lock and unlock the

vehicle when the electronic key cannot operate:

Locking the driver's

Unlocking the driver's

door

-

cell battery flat, vehicle battery discharged

or disconnected, ...

F

Insert the integral key in the door lock, then

turn it to the rear.

F

Insert the integral key in the door lock, then

turn it to the front.

-

vehicle located in an area with strong

electromagnetic signals.

F

Maintain a pull on button 1, to extract the

integral key 2.

If the alarm is activated, the audible

signal triggered on opening a door

with the key (integral with the remote

control) will stop when the ignition is

switched on.

Locking the passenger doors

Unlocking the passenger doors

F

Open the doors.

On the rear doors, check that the child lock

is not on.

F

Pull the interior door opening control.

For more information on the child lock, refer to

the corresponding section.

F

Remove the black cap, located on the edge

of the door, using the integral key.

Insert the integral key in the socket without

forcing it, then without turning it, move the

latch sideways towards the inside of the

door.

F

Remove the integral key and refit the cap.

Close the doors and check that the vehicle

has locked correctly from the outside.

59

Access

Remote control problem -

reinitialisation

changing the cell battery

Following disconnection of the vehicle battery,

replacement of the remote control battery or

in the event of a remote control malfunction,

you can no longer unlock, lock or locate your

vehicle.

Battery ref.: CR2032 / 3 volts.

This replacement battery is available from a

CITROËN dealer or a qualified workshop.

A message appears in the instrument panel

screen when replacement of the battery is

needed.

F

Place the mechanical key (integral with the

remote control) in the lock to unlock your

vehicle.

Place the electronic key in the reader.

Switch on the ignition by pressing

START/STOP.

F

Unclip the cover using a small screwdriver

at the cutout.

Do not throw the remote control

batteries away, they contain metals

which are harmful to the environment.

Take them to an approved collection

point.

F

Lift off the cover.

F

Remove the flat battery from its location.

Fit the new battery into its location

observing the original direction of fitment.

Clip the cover onto the casing.

The electronic key is fully operational again.

If the problem persists, contact a CITROËN

dealer or a qualified workshop as soon as

possible.

F

Lost electronic key

Visit a CITROËN dealer with the vehicle's registration certificate, your personal identification documents and if possible the key code label.

The CITROËN dealer will be able to retrieve the key code and the transponder code required to order a new key.

Electronic key

The electronic key is a sensitive system; do not operate it while it is in your pocket as there is a possibility that it may unlock the vehicle, without

you being aware of it.

Do not repeatedly press the buttons of your electronic key out of range and out of sight of your vehicle. You run the risk of stopping it from

working and the remote control would have to be reinitialised.

The electronic key cannot operate as a remote control when it is in the reader or even when the ignition is switched on.

Locking the vehicle

Driving with the doors locked may make access to the passenger compartment by the emergency services more difficult in an emergency.

As a safety precaution (with children on board), take the electronic key with you when you leave the vehicle, even for a short time.

Electrical interference

The electronic key may not operate if close to certain electronic devices: telephone, laptop computer, strong magnetic fields, ...

Anti-theft protection

Do not make any modifications to the electronic engine immobiliser system; this could cause malfunctions.

When purchasing a second-hand vehicle

Have all of the keys in your possession paired by a CITROËN dealer, to ensure that only your keys allow your vehicle to be unlocked and

started.

61

Access

Central locking

Manual central

locking

Automatic central locking

of doors (anti-intrusion

security)

The doors and boot lock automatically when

driving, as soon as the speed exceeds 6 mph

(10 km/h).

To activate or deactivate this function

(activated by default):

If one of the doors or the boot is

open, automatic central locking does

not complete: the sound of the locks

rebounding can be heard.

F

with the ignition on, press this

button until a message appears

in the instrument panel.

Transporting long or voluminous

objects

If you want to drive with the boot open

but the vehicle's side doors locked,

press the central locking control button

to lock the doors.

F

Press this button to operate the central

locking of the vehicle (doors and boot) from

inside the vehicle.

Pressing the button again unlocks the

vehicle completely.

When locking / deadlocking from the

outside

If the vehicle is locked or deadlocked from the

outside, the button is not active.

Driving with the doors locked may make

access to the passenger compartment

by the emergency services more

difficult in an emergency.

F

After normal locking, pull one of the interior

door handles to unlock the vehicle.

After deadlocking, you have to use the

remote control, the Keyless Entry and

Starting system or the integral key to

unlock the vehicle.

F

Boot

Opening from outside

Opening from inside

Tailgate release

System allowing the mechanical unlocking

of the boot in the event of a battery or central

locking system malfunction.

F

After unlocking the boot only or the vehicle,

press the opening control then raise the

tailgate.

F

Press this button until the boot is heard to

unlock.

Unlocking

F

Fold back the rear seats to gain access to

the lock from inside the boot.

Insert a small screwdriver into hole A of the

lock to unlock the tailgate.

closing

F

Lower the tailgate using the interior grab

handle.

Move the latch to the left.

If the tailgate is not closed correctly, engine

running or vehicle moving (speed above

6 mph (10 km/h)), a message appears in the

instrument panel screen for a few seconds.

Locking after closing

If the fault persists after closing again, the boot

will remain locked.

63

Access

Alarm

System which protects and provides a deterrent

against theft and break-in. It provides the

following types of monitoring:

Locking the vehicle with full

alarm system

Activation

- Exterior perimeter

F

Switch off the ignition and get out of the vehicle.

The system checks for opening of the vehicle.

The alarm is triggered if anyone tries to open a

door, the boot or the bonnet...

F

Press the locking button on the

remote control or lock the vehicle

using the Keyless Entry and

Starting system.

- Interior volumetric

The monitoring system is active: the indicator

lamp in the button flashes once per second.

The system checks for any variation in the

volume in the passenger compartment.

The alarm is triggered if anyone breaks a

window, enters the passenger compartment or

moves inside the vehicle.

Following an instruction to lock the

vehicle from the remote control or using

the Keyless Entry and Starting system,

the exterior perimeter monitoring is

activated after a delay of 5 seconds,

the interior volumetric monitoring

after 45 seconds and the anti-tilt after

90 seconds.

Self-protection function

The system checks for the putting out of

service of its components.

The alarm is triggered if the battery, the

button or the wires of the siren are put

out of service or damaged.

- Tilt

The system checks for any change in the

attitude of the vehicle.

The alarm is triggered if the vehicle is lifted,

moved or knocked.

For all work on the alarm system,

contact a CITROËN dealer or

a qualified workshop.

If an opening (door, boot...) is not closed

fully, the vehicle is not locked but the

exterior perimeter monitoring will be

activated after a delay of 45 seconds.

Locking the vehicle

with exterior perimeter

monitoring only

Deactivate the interior volumetric and anti-lift

monitoring to avoid unwanted triggering of the

alarm in certain cases such as:

deactivation of the interior

deactivation

volumetric and anti-tilt monitoring

F

Press the unlocking button on

F

Switch of the ignition and within

ten seconds, press this button

until the indicator lamp is on

continuously.

-

leaving a window partially open,

leaving a pet in the vehicle,

washing your vehicle,

changing a wheel,

having your vehicle towed,

transportation by sea.

the remote control or unlock the

vehicle using the Keyless Entry

and Starting system.

OFF

F

Get out of the vehicle.

Press the locking button on

the remote control immediately

or lock the vehicle using the

Keyless Entry and Starting

system.

The alarm system is deactivated: the

indicator lamp in the button goes off.

OFF

The exterior perimeter monitoring alone is

activated: the indicator lamp in the button

flashes once per second.

Where the vehicle locks itself again

automatically (occurs 30 seconds after

unlocking, if a door or the boot is not

opened), the monitoring system is not

reactivated automatically.

To reactivate it, the vehicle must be

unlocked and locked again, using the

remote control or the "Keyless Entry

and Starting" system.

To be effective, this deactivation must

be carried out each time the ignition is

switched off.

65

Access

Triggering of the alarm

Locking the vehicle without

activating the alarm

This is indicated by sounding of the siren

and flashing of the direction indicators for

thirty seconds.

F

Lock or deadlock the vehicle using the key

(integral with the remote control) in the

driver's door lock.

Reactivation of the interior

volumetric and anti-tilt monitoring

The monitoring functions remain active until

the alarm has been triggered eleven times in

succession.

F

Press the unlocking button on

the remote control or unlock the

vehicle using the Keyless Entry

and Starting system to deactivate

the exterior perimeter monitoring.

When the vehicle is unlocked using

the remote control or unlocked

using the Keyless Entry and Starting

Operating fault

When the ignition is switched on, fixed

illumination of the indicator lamp in the button

indicates a fault in the system.

Have it checked by a CITROËN dealer or a

qualified workshop.

OFF

system, rapid flashing of the indicator

lamp in the button informs you that the alarm

was triggered during your absence. When

the ignition is switched on, this flashing stops

immediately.

F

Press the locking button on the

remote control or lock the vehicle

using the Keyless Entry and

Starting system to activate all the

monitoring functions.

Automatic activation*

2 minutes after the last door or the boot is

Failure of the remote control

In this case, carry out the operations below to

closed, the system is activated automatically.

deactivate the monitoring functions:

F

To avoid triggering the alarm on entering

the vehicle, first press the unlocking button

on the remote control or unlock the vehicle

using the Keyless Entry and Starting

system.

The indicator lamp in the button

again flashes once per second.

F

Unlock the vehicle using the key (integral

with the remote control) in the driver's door

lock.

OFF

F

Open the door; the alarm is triggered.

Switch on the ignition; the alarm stops. The

indicator lamp in the button goes off.

* Depending on the country of sale.

Electric windows

Operation

Manual mode

To open or close the window, press or pull the

switch gently. The window stops as soon as the

switch is released.

Automatic mode

To open or close the window, press or pull

switch fully: the window opens or closes

completely when the switch is released.

Pressing or pulling the switch again stops the

movement of the window.

1. Left hand front electric window switch.

2. Right hand front electric window

switch.

4. Left hand rear electric window switch.

5. deactivating the rear electric window

switches,

3. Right hand rear electric window switch.

locking the rear doors

(child lock).

The electric window switches

remain operational for approximately

45 seconds after switching off the

ignition, while the vehicle's doors are

still closed.

Once a door is opened, or once the

45 seconds have elapsed, you have

to switch on the ignition to operate the

windows.

67

Access

deactivating the rear

window controls

Reinitialisation of the

electric windows

Safety anti-pinch

Following reconnection of the battery, the

When the window rises and meets an obstacle,

it stops and immediately partially lowers again.

In the event of unwanted opening of the

window on closing, press the switch until the

window opens completely, then pull the switch

immediately until the window closes. Continue

to hold the switch for approximately one second

after the window has closed.

For the safety of your children, press

safety anti-pinch function must be reinitialised.

The safety anti-pinch function is not active

during these operations.

switch 5 to prevent operation of the

rear windows irrespective of their

position.

For each window:

-

lower the window completely, then raise

it. It will rise in steps of a few centimetres

each time the switch is pressed. Repeat

the operation until the window closes

completely,

continue to press the switch for at least

one second after reaching this position,

window closed.

The warning lamp in the button comes on,

accompanied by a message confirming

activation. It remains on, as long as the child

lock is activated.

The interior controls for the rear doors are also

deactivated.

Opening the doors from the outside and

operation of the rear windows from the driver's

controls remain possible.

The safety anti-pinch function is not active

during this operation.

In the event of contact during operation of the windows, you must reverse the movement of

the window. To do this, press the switch concerned.

When operating the passenger electric window switches, the driver must ensure that no one

is preventing correct closing of the windows.

The driver must ensure that the passengers use the electric windows correctly.

Be particularly aware of children when operating the windows.

Be aware of passengers and other persons present close to the vehicle when closing the

windows remotely using the the electronic key or the Keyless Entry and Starting system.

Cockpit glass roof

Electric blinds

Automatic mode

F

Pull or press the control switch, going

beyond the point of resistance (forwards to

close and rearwards to open).

One press opens or closes the blind

completely.

Following a new action on the the control

switch, the blind continues to move for a

further 2 cm approximately, then stops.

Each of the three sections of the glass roof is

fitted with an electric blind.

The controls for the blinds can be operated

individually or simultaneously.

There are two options for opening and closing:

Manual mode

Safety anti-pinch

F

Pull or press the control switch without

going beyond the point of resistance

(forwards to close and rearwards to open).

When you release the control switch, the

blind continues to move for a further

2 cm approximately, then stops.

In automatic mode and at the end of its travel,

if the blind meets an obstacle while closing, it

stops and moves back slightly.

69

Access

Reinitialisation

In the event of a failure or battery disconnection

while a blind is moving or soon after it stops,

the safety anti-pinch must be reinitialised.

For each blind control switch:

If the blind meets an obstacle during

operation, you must reverse the

movement of the blind. To do this,

press the control switch for the blind in

question.

When the driver operates the blind

control switch, they must ensure that

no one is preventing correct closing of

the blind.

F

operate the control until the blind is fully

closed,

F

continue to press for at least 3 seconds.

A slight movement of the blind will then be

noticeable, confirming the reinitialisation.

The driver must ensure that passengers

use the blind correctly.

Be particularly aware of children when

operating the blind.

If the blind opens again on its own

during a closing movement or soon

after stopping:

F

operate the control switch until the

blind is fully open,

F

then operate the control switch until

the blind is fully closed.

The safety anti-pinch function is not

operational during these operations.

Access for Your Citroen Ds5 SUV First Generation (2011-2018)

Related Topics

Popular Owner Manuals

Latest Owner Manuals