2024-2026 Cupra Terramar SUV Lights User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Lights for Your Cupra Terramar SUV First Generation (2024-2026)

Lights
131
Vehicle lighting
Lights
Vehicle lighting
Control lamps
Lights up yellow
There is a total or partial failure of the
exterior lighting.
Lights up yellow
Rear fog light on.
Lights up green
Left or right turn signal. The control
lamp ashes twice as fast when a
turn signal is faulty.
Hazard warning lights on ›››
page72.
Lights up green
Trailer turn signals.
Lights up blue
Main beam on or asher on
›››page133.
Lights up blue
The Light Assist system is on
›››page134.
Lighting and visibility buttons
Fig.102 Instrument cluster: light panel.
By pressing the
button you can select be-
tween (the corresponding indicator lights up):
Switching on the dipped beam head-
lights.
Automatic control of dipped beam and
daytime running light.
Switching on the side lights. The auto-
matic headlight control activates at
over a speed of approx. 10km/h (6mph).
Additionally, the following light functions can
be activated by pressing on the corresponding
symbol.
When the function is activated, the corre-
sponding symbol lights up. To deactivate it, you
will need to press on the symbol again.
Turning the front fog lights on or o. In
addition, a pop-up window with the se-
lected position is displayed in the instru-
ment cluster.
Turning the rear fog lights on or o. In ad-
dition, the control lamp on the instrument
cluster lights up .
It is always the driver’s responsibility to ensure
that the vehicle is driven with the correct
headlamp settings and the correct lights.
Side lights
When the side light is switched on, the side
lights in both headlights, certain areas of the
rear light clusters, the number plate light and
the button lights on the instrument cluster turn
on. The automatic dipped beam activates as of
a speed of approx. 10 km/h (6 mph).
Automatic dipped beam headlight control
When the automatic dipped beam is switched
on, the vehicle's lighting and the lighting of the
instruments and controls turn on and o under
the following conditions:
●
The light sensor has detected darkness.
●
The wiper has been on for some time.
When the lights are on, the control lamp lights
up in green.
The automatic dipped beam is only an auxili-
ary function and cannot always identify all sit-
uations that may arise during driving with sui-
cient precision.
132
Lights
If the vehicle has the appropriate equipment,
the vehicle settings menu of the infotainment
system can be used to set the moment that
the dipped beam automatically switches on
›››page39.
Cornering light function
The cornering light is an additional function
to the dipped beam to improve lighting of the
side of the road when cornering at low speeds.
When the dipped beam is on, a static corner-
ing light comes on when driving at speeds be-
low about 40km/h (25mph) or on very tight
bends.
●
If the steering wheel is turned or the turn sig-
nal is switched on, the front fog light gradually
turns on. Once the turn has been made, the
cornering light progressively turns o.
●
When engaging reverse gear, both front fog
lights turn on.
Daytime running lights
Daytime running lights can increase the ve-
hicle’s visibility when driving in daylight and
they turn on automatically when the ignition
is switched on (if brightness is detected).
Motorway light
●
Activation: when going above 110km/h
(68mph) for more than 10 seconds, the dip-
ped beam raises slightly to increase the driver's
visibility distance.
●
Deactivation: when the speed of the vehicle
is reduced below 100km/h (62mph), the dip-
ped beam immediately returns to its normal
position.
Warning buzzers to warn that the lights have
not been switched o
If the ignition is not connected and the driver's
door is open, an audible warning signal is heard
in the following cases: this will remind you to
turn the light o.
●
When the parking light is on ›››page133.
●
When the lamp or is on.
If the exit lighting is switched on (“Coming
Home” function), when you leave the vehicle
there will be no audio warning to warn you that
the lights are still on.
WARNING
Accidents can occur if the road is not well lit
and other users of the road cannot see the
vehicle or see it with diiculty.
●
The automatic dipped beam control ( )
only switches on the dipped beam when
there are no changes in brightness, and not,
for example when it is foggy.
WARNING
The side light or daytime running light does
not provide suicient illumination to see the
road properly or to be seen by drivers of
other vehicles.
●
Always switch on the dipped beam head-
light at night, in rainy weather or when visibil-
ity is poor.
●
Daytime running lights must never be used
when the road is poorly lit due to weather or
lighting conditions.
WARNING
Other road users may be distracted and daz-
zled if the headlights are set too high and
used inappropriately. This could cause an ac-
cident, with serious consequences.
●
Always make sure that the headlights are
correctly adjusted .
Note
●
The relevant legislation in each country
must be observed when using the vehicle’s
lights.
●
The dipped beam headlights will only work
with the ignition on. When the ignition is
switched o, the side light automatically
turns on.
●
The rear fog light can dazzle drivers behind
you. You should use the rear fog light only
when visibility is very poor.
Lights
133
Vehicle lighting
1
2
3
4
●
When the lights are o or in position
or and the fog lights are switched on, the
dipped beam is also switched on regardless of
the ambient brightness.
Turn signal and main beam lever
Fig.103 Turn signal and main beam lever.
Move the lever to the required position:
Right turn light or right-hand parking light
(ignition switched o).
Left turn light or left-hand parking light (ig-
nition switched o).
Turning on the main beam. The control
lamp
lights up on the instrument clus-
ter.
The headlight asher turns on when the
lever is pulled. The control lamp
lights
up on the instrument cluster.
Place the lever in its neural position to turn o
the corresponding function.
Comfort turn signals
When the ignition is switched on, move the
lever as far as possible upwards or downwards
and release the lever. The turn signal will ash
three times.
To switch o the comfort turn signal early, im-
mediately move the lever in the opposite di-
rection until you feel resistance and release it.
The comfort turn signals can be activated and
deactivated in the infotainment system, in the
vehicle settings menu ›››
page39.
Parking light
The parking lights will only work with the igni-
tion o. If said light is on, an audible warning
will sound while the driver's door is open.
●
Switch the ignition o.
●
Move the turn signal lever up or down.
When the parking light is switched on, the
front side light and the tail light on the corre-
sponding side of the vehicle turn on.
Parking light on both sides
●
Switch the ignition o.
●
Press the button to select .
●
Lock the vehicle from the outside.
When this is done, only the side lights of both
headlights, along with the tail lights, partially
light up.
WARNING
Using turn signals inappropriately, not using
them or forgetting to turn them o can con-
fuse other road users. This could cause an
accident with serious consequences.
●
Always give warning of lane changes, over-
taking or turning manoeuvres by activating
the turn signals well in advance.
●
As soon as the lane change, overtaking or
turning manoeuvre is complete, switch o
the turn signal.
WARNING
Improper use of the main beam can cause
accidents and serious injuries, as it can dis-
tract and dazzle other drivers.
Note
●
When you turn the ignition o without hav-
ing turned the turn signals o, an audible sig-
nal sounds while the driver's door is open. It
is intended to remind you to turn o the turn
signals, unless you want to leave the parking
light on.
●
If the comfort turn signals are on (three
ashes) and the comfort turn signal on the
opposite side is activated, the active side
stops ashing and only ashes once on the
newly selected side.
134
Lights
●
The turn signals only work when the igni-
tion is switched on. The hazard warning lights
also work when the ignition is switched o.
●
The main beam can only be switched on
when the dipped beam is switched on.
●
If a trailer turn signal fails, the indicator
light (trailer turn signals) stops ashing, in-
stead of ashing the turn signal at double
speed in the vehicle.
●
In cold or wet weather conditions, the
headlights, tail lights and turn signals may be
temporarily fogged from the inside. This is
normal and has no eect on the service life
of the vehicle's lighting system.
●
The parking light does not activate auto-
matically if the left- or right-hand turn signal
is left on and the ignition is disconnected.
Main beam assist (Light Assist)
The main beam assist automatically prevents
glare from vehicles moving in the opposite di-
rection or ahead in the same direction. In addi-
tion, the main beam assist detects illuminated
areas and disconnects the main beam head-
light when passing, e.g. by populated areas.
Within its limitations, the assist system auto-
matically connects or disconnects the main
beam headlight depending on the environ-
mental and traic conditions, as well as the
speed ›››
.
Advanced main beam assistant (LED Matrix)
The advanced main beam assistant provides
maximum illumination of the road and road-
side. At the same time, it avoids dazzling vehi-
cles ahead or oncoming traic.
The system uses a camera to detect other road
users and deactivates certain areas within the
light distribution in a specic manner. If the
system cannot avoid dazzling other road users,
the main beam is switched o completely.
The advanced main beam assistant normally
recognizes illuminated areas such as cities
and deactivates the main beam while driving
through them.
Within the limits of the system, the assistant
automatically switches the main beam on or
o depending on the ambient conditions, traf-
c conditions and driving speed.
The advanced main beam assistant can be
switched on or o in the vehicle settings in the
Infotainment System.
Switching on the main beam assist or
advanced main beam assist (Matrix LED)
●
Switch on the ignition and select mode
on the headlight control ›››Fig.102.
●
From the neutral position, press the turn sig-
nal and main beam headlights lever forwards
›››Fig.103
3
.
When the main beam assist is switched on,
the control lamp on the instrument cluster
screen turns on. When the main beam is on,
the blue main beam control lamp on the
instrument cluster switches on.
Switching o the main beam assistant or ad-
vanced main beam assistant (LED Matrix)
●
Switching o mode on the headlight
control ›››Fig.102.
●
EITHER: if main beam assist is on, pull the
turn signal light and main beam headlights
lever back ›››Fig.103
4
.
●
OR: if the main beam assistant is on, but the
main beam does not turn on, press the turn
signal and main beam lever forwards to turn
the main beam on manually. Pull the turn sig-
nal and main beam lever back to switch o the
main beam manually, if necessary.
●
OR: switch o the ignition.
Additional functions
Depending on the equipment, the headlamps
are equipped with additional functions that im-
prove comfort and safety.
●
Lane light: If the system has detected that
the vehicle is travelling on a multi-lane motor-
way or similar roads the lane light illuminates
the full width of the driving lane. If vehicles
are detected ahead, the amount of lane illumi-
nated ahead of the vehicle reduces automat-
Lights
135
Vehicle lighting
ically. If the vehicle changes lanes, the illumi-
nated range is extended to both lanes for the
duration of the manoeuvre.
●
Orientation light: If the system has detec-
ted road works or sections of narrow road,
the orientation light uses markings to approxi-
mately show the likely position of the vehicle
in its lane, depending on the current steering
angle. The width of the markings corresponds
approximately to the width of the vehicle, but
does not reproduce it exactly. The length of
markings is automatically adjusted according
to speed and distance to vehicles in front.
These functions can be activated and deacti-
vated from Vehicle settings in the infotainment
system .
System limitations
In the following cases, the main beam head-
light must be switched o manually because
the main beam assist will not disconnect it on
time or disconnect it at all:
●
On insuiciently lit roads with highly reec-
tive signs.
●
If road users are insuiciently lit up, e.g. pe-
destrians or cyclists.
●
On closed curves, when the traic in the
opposite direction is partially hidden, on pro-
nounced slopes or inclinations.
●
On roads with traic in the opposite direction
and with a central reservation barrier where
the driver can see over it e.g. lorry drivers.
●
In case of fog, snow or heavy rainfall.
●
In case of swirling dust or sand.
●
If the windscreen is damaged in the camera's
eld of vision.
●
If the camera's eld of vision is misted up,
dirty or covered by a sticker, snow or ice.
●
If the camera is damaged or if the power
supply has been cut o.
WARNING
The comfort features of the main beam assist
must not lead you to take any risks. The sys-
tem is not a replacement for driver concen-
tration.
●
You must always control the main beam
yourself and adapt it to the light, visibility and
traic conditions.
●
The main beam regulator may not recog-
nise all driving situations correctly and may
operate with limitations in certain circum-
stances.
●
When the camera’s eld of view is dirty,
covered or damaged, the operation of the
main beam regulator may be aected. This
also applies when the vehicle’s lighting in-
stallation is modied, e.g. when additional
headlamps are installed.
NOTICE
To avoid aecting the operation of the sys-
tem, take the following points into considera-
tion:
●
Clean the eld of vision of the camera reg-
ularly and make sure it is free of snow and ice.
●
Do not cover the eld of vision of the cam-
era.
●
Check that the windscreen is not damaged
in the area of the camera’s eld of view.
Note
●
The headlight asher can be turned on and
o manually at any time with the turn signal
and main beam lever ›››
page133.
●
If there are objects that radiate light in the
camera's area of inuence, e.g. a portable
navigation system, this may aect the opera-
tion of the main beam assist system.
“Cominghome” and “Leav-
inghome” function (exterior ori-
entation lighting)
The “Cominghome” and “Leavinghome”
function lights up the vehicle’s immediate sur-
roundings when getting into and out of it in the
dark.
This light is automatically controlled by a light
sensor.
136
Lights
Turning on the “Leavinghome” light
●
Unlocks the vehicle (if the automatic dipped
beam function is switched on and the light
sensor detects darkness).
Turning o the “Leavinghome” light
●
It turns o automatically once the lights o
delay time has elapsed.
●
OR: lock the vehicle.
●
OR: press the light control as many times as
necessary until the instrument cluster displays
the setting .
●
OR: switch on the ignition.
Turning on the “Coming home” light
●
Switch the ignition o.
The “Coming home” light comes on if the au-
tomatic headlight control is switched on
and the light sensor detects darkness.
The lights-o delay countdown starts when
the last door or rear lid of the vehicle is closed.
Turning o the “Coming home” light
●
It switches o automatically after the set
lights-o delay time has elapsed.
●
EITHER: it is automatically deactivated if, 30
seconds after the function has been activated,
any vehicle door or the rear lid is still open.
●
OR: press the light control as many times as
necessary until the instrument cluster displays
the setting .
●
OR: switch on the ignition.
“Cominghome” and “Leavinghome” set-
tings
The duration of the lights-o delay can be set
in the vehicle settings menu of the infotain-
ment system, where the function can also be
activated and deactivated ›››page39.
Welcome light
The welcome light is a light located on the
exterior mirrors facing the ground which is
switched on or o if the lights control is in
the position and the “Coming Home” or
“Leaving Home” function is switched on or o.
The behaviour of the exterior lighting can be
set in the infotainment system. It is possible to
choose between two types of display:
●
Classic lighting: Background lighting, head-
lamps and tail lamps are switched on and o at
the same time.
●
Dynamic lighting: The background lighting,
headlights and tail lights turn on and o dy-
namically and, if applicable, with animation.
The access lighting when approaching the ve-
hicle can be activated or deactivated in vehi-
cles with a Keyless Access locking and ignition
system.
Dynamic headlight range control
The headlight range is automatically adjusted
according to the vehicle load status when they
are switched on.
WARNING
If the dynamic headlight range control fails
or does not work properly, the headlights
could dazzle and distract other road users.
This could cause accidents and lead to seri-
ous injuries.
●
Immediately go to a specialist workshop
and have the headlight range control system
checked.
Driving abroad
The light beam of the dipped beam lights is
asymmetric: the side of the road on which you
are driving is lit more intensely.
When a car that is manufactured in a country
that drives on the right travels to a country that
drives on the left (or vice versa), it is normally
necessary to cover part of the headlight bulbs
with stickers or to change the adjustment of
the headlights to avoid dazzling other drivers.
In such cases, the regulations specify certain
light values that must be complied with for
designated points of the light distribution. This
is known as “Tourist light”.
Lights
137
Interior lights
The light distribution of the headlights allows
the specic “tourist light” values to be met
without the need for stickers or changes being
made to the settings.
Note
“Tourist light” is only allowed temporarily. If
you are planning a long stay in a country that
drives on the other side, you should take the
vehicle to an Authorised Technical Service to
change the headlights.
Interior lights
Lighting of the instrument cluster,
displays and controls
The instrument and control lighting brightness
can be set in the vehicle settings menu of the
infotainment system ›››
page39.
The set intensity automatically adapts to
changes in ambient brightness in the vehicle.
When the automatic dipped beam light
is turned on, a sensor automatically turns the
dipped beam light on or o, along with the
instrument and control lighting, depending on
the ambient brightness.
In some cases, e.g. when driving through a
tunnel without the automatic dipped beam
light
function switched on, the instrument
cluster lighting may even switch o. The objec-
tive of this function is to provide the driver with
a visual indication that he or she should acti-
vate the dipped beam. If your vehicle is tted
with a digital instrument cluster, the message
Turn on the lights will be displayed on the in-
strument cluster.
Interior and reading lights
Fig.104 Detail of headliner: front interior
lighting.
Turning the interior lights on or o.
Door contact connection. The interior
lights come on automatically when you
unlock the vehicle, open a door or dis-
connect the ignition. The light goes out
a few seconds after closing all the doors,
when locking the vehicle or connecting
the ignition.
Reading light
The reading light is touch-operated, each lens
is turned on and o individually by pressing in
the respective central area. In addition, the in-
tensity of the light can be adjusted according
to the pressure exerted.
If you want to turn on the two lenses together
you must press the symbol
›››Fig.104.
Glove compartment and luggage compart-
ment lighting
When opening and closing the glove compart-
ment on the front passenger side and the rear
lid, the respective light will automatically switch
on and o.
Footwell lighting
The lights in the footwell area below the dash
panel (driver and front passenger sides) will
switch on when the doors are opened and
will decrease in brightness while driving. This
brightness can be adjusted through the info-
tainment system menu using the function but-
ton > Lighting > Settings ›››page39.
Note
The reading lights go out when the vehicle
is closed and locked or after a few minutes
of turning the ignition o. This prevents the
battery from discharging.
138
Lights
Lighting prole
Individual
O
Background lighting
Fig.105 Schematic representation:
Background lighting.
Background lighting provides lighting in dier-
ent areas of the interior.
There are predened versions of Ambient
Light ›››
Fig.105.
The intensity of the lighting can be adjusted
using the function button :
Lights up the interior of the
vehicle depending on the selected lighting
prole.
To adjust the intensity of the back-
ground lighting in each of the areas as well
as to change the colour in the versions
that have lighting on the front door panel
and the instrument panel line.
Turns o the background lighting.
Additional functions of the background
lighting
●
Door open alert: Representation on the line
of the respective front door if the vehicle rea-
ches 10 km/h while either of the two front
doors is not closed properly.
●
Rear windows locked alert: Representation
on the line of the respective front door when
the operation buttons of the rear windows are
pressed, if they have been locked with the
safety button ›››page117 and the vehicle is
locked (Auto Lock).
●
Representation of the hazard warning
lights: Animation on the entire background
lighting line while the hazard warning light
function is active.
●
Representation of acceleration: Animation
on the entire background lighting line when
accelerating. This function is only represented
in the Cupra when the link between the back-
ground lighting and the drive prole is activa-
ted. If a door has been left open, the “Door
Open Alert” will be displayed at a speed above
10km/h.
The representation of these functions by the
background lighting can be switched on and
o both individually and as a whole in the info-
tainment system:
> Lighting > Settings.

Related Topics

Popular Owner Manuals