Get Driving -> Cruise control Guide for Dacia Sandero 4 Door Second Generation (2013-2020)

Jaune Noir Noir texte

CRUISE CONTROL/SPEED LIMITER: cruise control function (1/4)

3

4

5

2

1

This function is an additio-

nal driving aid. However,

the function does not take

the place of the driver.

Therefore, it can under no circums-

The cruise control function helps you to

maintain your driving speed at a speed

that you choose, called the cruising

speed.

Controls

1 Main “On/Off” switch.

tances replace the driver’s responsi-

bility to respect speed limits and to

be vigilant (the driver must always

be ready to brake).

2 Cruising speed activation, storage

and increase switch (+).

This cruising speed may be set at any

speed above 20 mph (30 km/h).

Cruise control must not be used in

heavy traffic, on undulating or slip-

pery roads (black ice, aquaplaning,

gravel) and during bad weather (fog,

rain, side winds etc.).

3 Decreasing cruising speed (-).

4 Activation with recall of saved crui-

sing speed (R).

5 Switch the function to standby (with

There is a risk of accidents.

cruising speed saved) (O).

The cruise control function

is in no way linked to the

braking system.

2.27

ENG_UD32524_3

Régulateur-limiteur de vitesse : fonction régulateur (X52 - Dacia)

ENG_NU_993-5_X52_Dacia_2

Downloaded from manuals search engine

Jaune Noir Noir texte

CRUISE CONTROL/SPEED LIMITER: cruise control function (2/4)

2

3

1

7

6

Switching on

Activating cruise control

Driving

At a steady speed (above 18 mph

(30 km/h approximately)) press switch 2

or (+): the function is activated and the

current speed is saved.

Once a cruising speed is stored and

the cruise control function is active,

you may lift your foot off the accelera-

tor pedal.

Press switch 1 side ꢀ.

The warning light 6 comes on, lit green,

and the message “CRUISE” appears

on the instrument panel, accompanied

by dashes to indicate that the cruise

control function is activated and waiting

to store a cruising speed.

The cruising speed replaces the

dashes and the cruise control is confir-

med by the appearance of the message

^{“CRUISE” and the warning light 6}ꢀ

being lit green, as well as the warning

^{light 7}ꢁ.

Important: you are never-

theless advised to keep

your feet close to the pedals

in order to react if neces-

sary.

2.28

ENG_UD32524_3

Régulateur-limiteur de vitesse : fonction régulateur (X52 - Dacia)

ENG_NU_993-5_X52_Dacia_2

Downloaded from manuals search engine

Jaune Noir Noir texte

CRUISE CONTROL/SPEED LIMITER: cruise control function (3/4)

Exceeding the cruising speed

The cruising speed may be exceeded

at any time by depressing the accele-

rator pedal. While it is being exceeded,

the cruising speed flashes on the ins-

2

3

trument panel.

Then, release the accelerator: after a

few seconds, the vehicle will automa-

tically return to its set cruising speed.

Cruising speed cannot be

maintained

When driving down a steep gradient,

the system is unable to maintain the

cruising speed: the stored speed will

flash on the instrument panel informa-

tion display to inform you of this situa-

tion.

Adjusting the cruising speed

The cruising speed may be changed by

pressing the following repeatedly:

– switch 2 (+) to increase the speed,

– switch 3 (-) to decrease the speed.

The cruise control function

is in no way linked to the

braking system.

2.29

ENG_UD32524_3

Régulateur-limiteur de vitesse : fonction régulateur (X52 - Dacia)

ENG_NU_993-5_X52_Dacia_2

Downloaded from manuals search engine

Jaune Noir Noir texte

CRUISE CONTROL/SPEED LIMITER: cruise control function (4/4)

Returning to the cruising speed

If a speed is stored, it can be recalled,

once you are sure that the road condi-

tions are suitable (traffic, road sur-

face, weather conditions, etc.). Press

switch 4 (R) if the vehicle speed is

above 20 mph (30 km/h).

3

2

4

5

When the stored speed is recalled, acti-

vation of the cruise control is confirmed

^{by the illumination of the}ꢁ warning

light.

1

NB: if the speed previously stored is

much higher than the current speed,

the vehicle will accelerate more rapidly

to reach this threshold.

Putting the function on

standby

The function is set to standby if you:

Switching off the function

The cruise control function is deactiva-

ted if you press switch 1: in this case

a speed is no longer stored. The two

^{instrument panel warning lights}ꢀ and

ꢁ go out to confirm that the function is

deactivated.

– use the switch 5 (O);

– the brake pedal;

– depress the clutch pedal or shift into

neutral if the vehicle has an automa-

tic gearbox.

In all three cases, the cruising speed re-

mains stored and the message “MEM”

appears on the instrument panel.

When the cruise control function is

put on standby, pressing switch 2

(+) reactivates the cruise control

function without taking into account

the stored speed: it is the speed at

which the vehicle is moving that is

taken into account.

Putting the cruise control

on standby or switching it

off does not cause a rapid

reduction in speed: you

must brake by depressing the brake

pedal.

Standby is confirmed when indicator

^lightꢁ goes out.

2.30

ENG_UD32524_3

Régulateur-limiteur de vitesse : fonction régulateur (X52 - Dacia)

ENG_NU_993-5_X52_Dacia_2

Downloaded from manuals search engine

Driving -> Cruise control for Your Dacia Sandero 4 Door Second Generation (2013-2020)

Related Topics

Popular Owner Manuals

Latest Owner Manuals