Get Access -> Alarm Guide for DS 3 Crossback 4 Door First Generation (2018-2022)

Access

Too frequent presses on the handle up to

the point of resistance may damage its

mechanism.

With selective unlocking activated:

– Opening the driver's door unlocks the

driver's door only (if the vehicle has not already

been completely unlocked).

Unlocking

►ꢀ Fold the rear seats to gain access to the lock

from inside the boot.

– Opening one of the passenger doors unlocks

the rest of the vehicle.

In case of frost, press the handle to

release it.

– Opening a door from inside causes the

unfolding of all the exterior handles.

From inside the vehicle, it is possible to unfold the

handles:

– by opening a door,

– by pressing the central locking button once

when the vehicle is locked or twice when

unlocked.

When driving, the handles automatically retract

once the vehicle speed exceeds 2 mph (3 km/h).

Boot

►ꢀ Insert a small screwdriver into hole A of the

lock to unlock the boot.

►ꢀ Move the latch to the left.

Opening

Locking after closing

If the fault persists after closing again, the boot

will remain locked.

Opening

From outside

►ꢀ Unlock your vehicle to unfold the door handles.

►ꢀ Pull the handle.

Alarm

(Depending on version)

►ꢀ After unlocking the vehicle or just the boot,

press the opening control and then raise the

tailgate.

When selective unlocking is activated,

only the driver door's handle will unfold

and only the driver's door can be opened.

Closing

►ꢀ Lower the tailgate using one of the interior

From inside

►ꢀ Pull the interior door opening lever; the exterior

door handles unfold automatically.

Opening one of the doors from inside unlocks the

rest of the vehicle.

grab handles.

Back-up release

To manually unlock the boot in the event of a

battery or central locking failure.

Access

System which protects and provides a deterrent

against theft and break-ins.

When the monitoring system is active, the red

indicator lamp in the button flashes once per

second and the direction indicators come on for

about 2 seconds.

The exterior perimeter monitoring is activated

after 5 seconds and the interior volumetric

monitoring after 45 seconds.

After unlocking using the remote control

If the vehicle automatically locks itself

again (as happens if a door or the boot is not

opened within 30 seconds of unlocking), the

monitoring system is automatically activated.

Exterior perimeter monitoring

The system checks for opening of the vehicle.

The alarm is triggered if anyone tries to open a

door, the boot or the bonnet, for example.

Locking the vehicle with

exterior perimeter monitoring

only

Disable volumetric monitoring to avoid unwanted

alarm triggering in certain cases, such as:

– Slightly open window.

– Washing the vehicle.

– Changing a wheel.

– Towing your vehicle.

Interior volumetric monitoring

The alarm does not activate when locking

automatically from a distance.

The system checks for any variation in volume in

the passenger compartment.

The alarm is triggered if anyone breaks a window,

enters the passenger compartment or moves

inside the vehicle.

If an opening (door, boot or bonnet) is not

properly closed, the vehicle is not locked,

but the exterior perimeter monitoring will be

activated after 45 seconds, at the same time

as the interior volumetric monitoring.

Self-protection function

The system checks for the putting out of service

of its components.

– Transport on a ship or ferry.

The alarm is triggered if the battery, the central

control or the siren wiring is put out of service or

damaged.

Deactivation

►ꢀ Press one of the remote control unlocking

buttons:

Deactivating interior volumetric

monitoring

►ꢀ Switch off the ignition and within 10 seconds

press the alarm button until the indicator lamp is

on fixed.

For all work on the alarm system, contact

a dealer or a qualified workshop.

short press

long press

►ꢀ Exit the vehicle.

Locking the vehicle with full

alarm system

►ꢀ Immediately lock the vehicle using the remote

control or by pressing one of the front door

handles.

Only exterior perimeter monitoring is activated;

the red indicator lamp in the button flashes every

second.

►ꢀ Unlock the vehicle using the remote control or

by pressing one of the front door handles.

The monitoring system is deactivated: the

indicator lamp in the button goes off and the

direction indicators flash for about 2 seconds.

Activation

►ꢀ Switch off the ignition and exit the vehicle.

►ꢀ Lock or deadlock the vehicle using the remote

control or by pressing on one of the front door

handles.

To take effect, this deactivation must be

performed whenever the ignition is switched off.

Access

Reactivating interior volumetric

monitoring

►ꢀ Deactivate exterior perimeter monitoring by

unlocking the vehicle using the remote control or

by pressing a door handle.

The indicator lamp in the button goes off.

►ꢀ Reactivate the full alarm system by locking

the vehicle using the remote control or by

pressing one of the front door handles.

The red indicator lamp in the button once again

flashes every second.

Locking the vehicle without

activating the alarm

Electric windows

►ꢀ Lock or deadlock the vehicle using the key

(integral to the remote control) in the driver's door

lock.

Automatic activation

(Depending on version)

The system is activated automatically 2 minutes

after the last door or the boot is closed.

►ꢀ To avoid triggering the alarm on entering the

vehicle, first press the unlocking button on the

remote control or unlock the vehicle using the

“Keyless Entry and Starting” system.

1. Left-hand front.

2. Right-hand front.

3. Left-hand rear.

4. Right-hand rear.

5. Deactivation of the electric window controls

located at the rear seats.

Locking of the rear doors (depending on

version).

Triggering of the alarm

This is indicated by sounding of the siren and

flashing of the direction indicators for 30

seconds.

The interior volumetric and anti-tilt monitoring

functions remain active until the alarm has been

triggered ten times in succession.

When the vehicle is unlocked, rapid flashing of

the indicator lamp in the button indicates that the

alarm was triggered during your absence. When

the ignition is switched on, this flashing stops

immediately.

Malfunction

When the ignition is switched on, fixed

illumination of the red indicator lamp in the

button indicates a malfunction of the system.

Have it checked by a dealer or a qualified

workshop.

Manual operation

►ꢀ To open/close the window, press/pull the

switch without passing the point of resistance;

the window stops as soon as the switch is

released.

Failure of the remote control

Automatic operation

To deactivate the monitoring functions:

►ꢀ Unlock the vehicle using the key in the driver's

door lock.

►ꢀ To open/close the window, press/pull the

switch past its resistance point: the window

opens/closes completely when the switch is

released.

►ꢀ Open the door; the alarm is triggered.

►ꢀ Switch on the ignition; this stops the alarm.

The indicator lamp in the button goes off.

Access -> Alarm for Your DS 3 Crossback 4 Door First Generation (2018-2022)

Related Topics

Access

Popular Owner Manuals

Latest Owner Manuals