Access -> Electric windows for Your DS 3 Crossback 4 Door First Generation (2018-2022)

36  
Access  
02  
Reactivating interior volumetric  
monitoring  
►ꢀ Deactivate exterior perimeter monitoring by  
unlocking the vehicle using the remote control or  
by pressing a door handle.  
The indicator lamp in the button goes off.  
►ꢀ Reactivate the full alarm system by locking  
the vehicle using the remote control or by  
pressing one of the front door handles.  
The red indicator lamp in the button once again  
flashes every second.  
Locking the vehicle without  
activating the alarm  
Electric windows  
►ꢀ Lock or deadlock the vehicle using the key  
(integral to the remote control) in the driver's door  
lock.  
Automatic activation  
(Depending on version)  
The system is activated automatically 2 minutes  
after the last door or the boot is closed.  
►ꢀ To avoid triggering the alarm on entering the  
vehicle, first press the unlocking button on the  
remote control or unlock the vehicle using the  
“Keyless Entry and Starting” system.  
1. Left-hand front.  
2. Right-hand front.  
3. Left-hand rear.  
4. Right-hand rear.  
5. Deactivation of the electric window controls  
located at the rear seats.  
Locking of the rear doors (depending on  
version).  
Triggering of the alarm  
This is indicated by sounding of the siren and  
flashing of the direction indicators for 30  
seconds.  
The interior volumetric and anti-tilt monitoring  
functions remain active until the alarm has been  
triggered ten times in succession.  
When the vehicle is unlocked, rapid flashing of  
the indicator lamp in the button indicates that the  
alarm was triggered during your absence. When  
the ignition is switched on, this flashing stops  
immediately.  
Malfunction  
When the ignition is switched on, fixed  
illumination of the red indicator lamp in the  
button indicates a malfunction of the system.  
Have it checked by a dealer or a qualified  
workshop.  
Manual operation  
►ꢀ To open/close the window, press/pull the  
switch without passing the point of resistance;  
the window stops as soon as the switch is  
released.  
Failure of the remote control  
Automatic operation  
To deactivate the monitoring functions:  
►ꢀ Unlock the vehicle using the key in the driver's  
door lock.  
►ꢀ To open/close the window, press/pull the  
switch past its resistance point: the window  
opens/closes completely when the switch is  
released.  
►ꢀ Open the door; the alarm is triggered.  
►ꢀ Switch on the ignition; this stops the alarm.  
The indicator lamp in the button goes off.  
37  
Access  
02  
Operating the switch again stops the movement  
of the window.  
Reinitialising the electric  
windows  
Window controls remain operational for  
approximately 45 seconds after switching  
off the ignition or after locking the vehicle.  
After that time, the controls are disabled.  
To reactivate them, switch on the ignition or  
unlock the vehicle.  
After reconnecting the battery, or in the event  
of abnormal window movement, the anti-pinch  
function must be reinitialised.  
The anti-pinch function is disabled during the  
following sequence of operations.  
For each window:  
►ꢀ Lower the window fully, then raise it; it will  
rise in steps of a few centimetres each time the  
control is pressed. Repeat the operation until the  
window is fully closed.  
Anti-pinch  
If the window meets an obstacle while rising, it  
stops and immediately partially lowers again.  
►ꢀ Continue to pull the control upwards for at  
least one second after the window reaches the  
closed position.  
Deactivation of the rear  
controls for the rear electric  
windows  
If an electric window meets an obstacle  
during operation, the movement of the  
window must be reversed. To do this, press the  
relevant switch.  
When the driver operates the passengers’  
electric window switches, it is important to  
ensure that nothing can prevent the window  
from closing properly.  
It is important to ensure that passengers use  
the electric windows correctly.  
Pay particular attention to children when  
operating windows.  
For children's safety, press switch 5 to  
deactivate the rear electric windows  
controls.  
The indicator lamp for the button comes on,  
accompanied by a message confirming activation.  
With the ignition on, it remains lit, as long as the  
child lock remains activated.  
Use of the rear electric windows from the driver's  
controls remains possible.  
For versions fitted with an electric child  
lock, this control also deactivates the  
interior rear door controls.  
For more information on the Child lock, refer to  
the corresponding section.  
Be aware of passengers and/or other persons  
present when closing windows using the key or  
the "Keyless Entry and Starting" system.