Get Getting To Know Your Instrument Panel -> Maintenance Monitor Guide for Fiat 124 Spider 2 Door Second Generation (2016-2020)

Note: Always set the vehicle speed

according to the laws and regulations of

the country/city in which the vehicle is

driven. In addition, always verify the

speed of the vehicle using the

speedometer.

Tachometer

Engine Coolant

Temperature Gauge And

Fuel Gauge

The tachometer shows engine speed in

thousands of revolutions per minute

(rpm).

Engine Coolant Temperature Gauge

The range varies depending on the type

of gauge.

The vehicle speed alarm can be set

using the following procedure:

1. Press the INFO switch to display the

Vehicle Speed Alarm mode.

2. Press the INFO switch continuously

until a beep sound is heard. The set

vehicle speed display flashes the first

digit.

3. Press the INFO switch and set the

first digit to the desired vehicle speed.

The numerical value changes each time

the INFO switch is pressed.

05020103-12A-002

Tachometer

1 — Tachometer Display

4. Press the INFO switch continuously

until a beep sound is heard. The set

vehicle speed display flashes the lower

two digits.

5. Press the INFO switch and set the

two lower digits to the desired vehicle

speed. The numerical value changes

each time the INFO switch is pressed.

0502010417A007

Fuel/Temperature Gauge

1 — Engine Coolant Temperature

2 — Fuel Gauge

6. Press the INFO switch continuously

until a beep sound is heard. The set

vehicle speed is displayed on the

vehicle speed alarm screen.

Note: If the high engine coolant

temperature warning light (red) turns

on, there is a possibility of overheating.

Park the vehicle in a safe place

immediately and take appropriate

measures. If the vehicle continues to be

driven, it could cause damage to the

engine.

Outside Temperature

Display

Changing The Temperature Unit Of

The Outside Temperature Display

The outside temperature unit can be

switched between Fahrenheit and

Celsius using the following procedure.

When the ignition is in the ON position,

the outside temperature is displayed.

Fuel Gauge

The fuel gauge shows approximately

how much fuel is remaining in the tank

when the ignition is in the ON position.

We recommend keeping the tank over

1/4 full.

Vehicles With Fiat Connect 7.0

Settings can be changed through the

Connect 7.0 radio screen. Refer to

“Personalization Features” in this

chapter.

E = Empty

F = Full

Vehicles With Fiat Radio 3.0

Proceed as follows:

If the low fuel warning light illuminates

or the fuel level is very low, refuel as

soon as possible.

1. Push the INFO switch with the

ignition in the OFF position and

continue pushing the INFO switch for

5 seconds or longer while placing the

ignition in the ON position. The outside

temperature display flashes.

05020107345034

Outside Temperature Screen

Display

Note:

After refueling, it may require some

time for the indicator to stabilize. In

addition, the indicator may deviate

while driving on a slope or curve since

the fuel moves in the tank.

Under the following conditions, the

outside temperature display may differ

from the actual outside temperature

depending on the surroundings and

vehicle conditions:

2. Push the INFO switch to change the

outside temperature unit.

3. Push and hold the INFO switch for

3 seconds or longer while the outside

temperature display is flashing. The

outside temperature display illuminates.

The display indicating a quarter or

less remaining fuel has more segments

to show the remaining fuel level in

greater detail.

Significantly cold or hot

temperatures.

Sudden changes in outside

temperature.

Note: When the temperature unit

indicated in the outside temperature

display is changed, the temperature

unit indicated in the engine coolant

gauge display changes in conjunction

with it.

The direction of the arrow on the

fuel gauge indicates that the fuel door

lid is on the left side of the vehicle.

The vehicle is parked.

The vehicle is driven at low speeds.

Cruise Control Set

Vehicle Speed Display

Vehicles with Manual Transmission

MAINTENANCE

MONITOR — IF

EQUIPPED

The gear shift indicator turns off when

the following operations are performed:

The vehicle speed preset using the

cruise control is displayed.

The vehicle is stopped

Oil Life Reset

The vehicle is put in neutral

The vehicle is driven in reverse

Vehicles With Fiat Radio 3.0

“Oil Change” with flexible settings are

available. Consult an authorized dealer

for details.

The clutch is not fully engaged when

accelerating

Note: The engine oil flexible

The clutch pedal remains depressed

for 2 seconds or longer while driving

maintenance setting is available (if

equipped). Based on the engine

operating conditions, the on-board

computer in your vehicle calculates the

remaining oil life. When the engine oil

flexible maintenance setting is selected,

the system must be reset whenever

replacing the engine oil.

Vehicles with Automatic

Transmission

0502010819A019

The gear shift indicator turns off when

the following operations are performed:

Cruise Control Display Screen

Gear Shift Indicator — If

Equipped

The vehicle is stopped

When the engine oil flexible

Manual shift mode is canceled

maintenance setting is selected, the

Indicator light will illuminate in the

instrument cluster when remaining oil

life becomes less than 300 miles

(500 km) or remaining days are less

than 15 (whichever comes first).

The gear shift indicator helps the driver

obtain optimum fuel economy and

smooth driving. It displays the selected

Gear Position 1 in the instrument

cluster and also notifies the driver to

change to the most suitable Gear

Position 2 corresponding to the actual

driving condition.

Manually Shifting Up (Versions with

Automatic Transmission)

Using the selector lever: to shift up to a

higher gear, tap the selector lever back

+ once.

Note: Do not rely solely on the

shift-up/shift-down recommendations

by indications. The actual driving

situation might require shift operations

different from indication. To avoid the

risk of accidents, the road and traffic

conditions have to be judged correctly

by the driver before shifting.

Reset Method

Oil Life Reset

Your vehicle is equipped with an engine

oil change indicator system. The “Oil

Change Required” message will flash in

the instrument cluster display for

approximately ten seconds after a

single chime has sounded to indicate

the next scheduled oil change interval.

The engine oil change indicator system

is duty cycle based, which means the

engine oil change interval may fluctuate,

dependent upon your personal driving

style.

Vehicles With FIAT Connect

7.0 Radio

Proceed as follows:

1. Select the icon

on the home

screen to display the “Applications”

screen.

2. Select “Maintenance” to display the

maintenance list screen.

3. Switch the tab and select the setting

item you want to change: “Scheduled,”

“Tire Rotation,” or “Oil Change.”

Unless reset, this message will continue

to display each time you turn the

ignition switch to the ON/RUN position.

To reset the oil change indicator system

(after performing the scheduled

maintenance), refer to the following

procedure

1. Place the ignition in the ON position.

(Do not start the engine.)

2. Fully push the accelerator pedal

slowly to the floor, three times within ten

seconds.

3. Place the ignition in the OFF/LOCK

position.

Note: If the indicator message

illuminates when you start the vehicle,

the oil change indicator system did not

reset. If necessary, repeat this

procedure.

Getting To Know Your Instrument Panel -> Maintenance Monitor for Your Fiat 124 Spider 2 Door Second Generation (2016-2020)

Related Topics

Getting To Know Your Instrument Panel

Popular Owner Manuals

Latest Owner Manuals