Get Servicing and Maintenance -> Wheels and Tires Guide for Fiat 124 Spider 2 Door Second Generation (2016-2020)

Lubricate the external lock cylinders

twice a year. Apply a small amount of

high-quality lubricant directly into the

lock cylinder. If necessary, contact your

authorized dealer.

Note:

Hot waxes applied by automatic car

washers have been known to affect

the wiper's ability to clean windows.

Blade Replacement

Proceed as follows:

1. Raise the wiper arm.

2. Open the clip and slide the blade

assembly in the direction of the arrow.

To prevent damage to the wiper

blades, do not use gas, paraffin, paint

thinner, or other solvents on or near

them.

Wiper Blades

Contamination of either the windshield

or the blades with foreign matter can

reduce wiper effectiveness. Common

sources are insects, tree sap, and hot

wax treatments used by some

Be careful not to pinch hands or

fingers as it may cause injury, or

damage the wipers. When washing or

servicing the vehicle, make sure the

wiper lever is in the OFF position.

commercial car washes.

If the blades are not wiping properly,

clean the window and blades with a

good cleaner or mild detergent; then

rinse thoroughly with clean water.

Repeat if necessary.

Replacing Windshield Wiper Blades

When the wipers no longer clean well,

the blades are probably worn or

cracked. Replace them.

07031101-36A-001

Clip

When the wiper lever is in the AUTO

position and the ignition is cycled to the

ON mode, the wipers may move

When raising both windshield wiper

arms, raise the driver's side wiper arm

first.

automatically in the following cases:

When lowering the wiper arms, slowly

lower the wiper arm from the

If the windshield above the rain

sensor is touched.

passenger's side first while supporting

it with your hand. Forcefully lowering

the wiper arms could damage the wiper

arm and blade, and may scratch or

crack the windshield.

If the windshield above the rain

sensor is wiped with a cloth.

If the windshield is struck with a hand

or other object.

Note: To prevent damage to the wiper

arms and other components, do not try

to sweep the wiper arm by hand.

If the rain sensor is struck with a

hand or other object from inside the

vehicle.

244

3. Tilt the blade assembly and remove

it from the arm.

Note:

Do not bend or discard the

stiffeners, they will be reused.

If the metal stiffeners are switched,

the blade's wiping efficiency could be

reduced. Do not use the driver's side

metal stiffeners on the passenger's

side, or vice versa.

Be sure to reinstall the metal

stiffeners in the new blade rubber so

that the curve is the same as it was in

the old blade rubber.

07031101-36A-003

Blade Holder

07031101-36A-002

5. Remove the metal stiffeners from

each blade rubber and install them in

the new blade.

6. Carefully insert the new blade

rubber. Then install the blade assembly

in the reverse order of removal.

Blade Assembly and Arm

Warning!

To prevent damage to the windshield let

the wiper arm down easily, do not let it slap

down on the windshield.

4. Pull down the blade rubber and slide

it out of blade holder.

07031101-36A-004

07031101-36A-005

Metal Stiffeners

Reassemble Blade

245

Note:

P (Passenger) — Metric tire sizing is

RAISING THE

VEHICLE

WHEELS AND TIRES

Tire Safety Information

based on U.S. design standards.

P-Metric tires have the letter “P”

molded into the sidewall preceding the

size designation. Example:

If the vehicle needs to be raised, see an

authorized dealer which is equipped

with arm hoists or workshop lifts.

Tire safety information will cover

aspects of the following information:

Tire Markings, Tire Identification

Numbers, Tire Terminology and

Definitions, Tire Pressures, and Tire

Loading.

The vehicle’s lifting points are marked

on the side skirts with the symbols.

P215/65R15 95H.

European — Metric tire sizing is

based on European design standards.

Tires designed to this standard have

the tire size molded into the sidewall

beginning with the section width. The

letter "P" is absent from this tire size

designation. Example: 215/

Tire Markings

65R15 96H.

LT (Light Truck) — Metric tire sizing

is based on U.S. design standards.

The size designation for LT-Metric tires

is the same as for P-Metric tires except

for the letters “LT” that are molded into

the sidewall preceding the size

0601085395US

Tire Markings

designation. Example: LT235/85R16.

1 — U.S. DOT

4 — Maximum

Temporary spare tires are designed

for temporary emergency use only.

Temporary high pressure compact

spare tires have the letter “T” or “S”

molded into the sidewall preceding the

size designation. Example:

Safety Standards Load

Code (TIN)

2 — Size

5 — Maximum

Pressure

Designation

3 — Service

Description

6 — Treadwear,

Traction and

Temperature

Grades

T145/80D18 103M.

High flotation tire sizing is based on

U.S. design standards and it begins

with the tire diameter molded into the

sidewall. Example: 31x10.5 R15 LT.

246

Tire Sizing Chart

EXAMPLE:

Example Size Designation: P215/65R15XL 95H, 215/65R15 96H, LT235/85R16C, T145/80D18 103M, 31x10.5 R15 LT

P = Passenger car tire size based on U.S. design standards, or

"....blank...." = Passenger car tire based on European design standards, or

LT = Light truck tire based on U.S. design standards, or

T or S = Temporary spare tire or

31 = Overall diameter in inches (in)

215, 235, 145 = Section width in millimeters (mm)

65, 85, 80 = Aspect ratio in percent (%)

Ratio of section height to section width of tire, or

10.5 = Section width in inches (in)

R = Construction code

"R" means radial construction, or

"D" means diagonal or bias construction

15, 16, 18 = Rim diameter in inches (in)

Service Description:

95 = Load Index

A numerical code associated with the maximum load a tire can carry

H = Speed Symbol

A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions

The maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e., tire pressure,

vehicle loading, road conditions, and posted speed limits)

247

EXAMPLE:

Load Identification:

Absence of the following load identification symbols on the sidewall of the tire indicates a Standard Load (SL) tire:

XL = Extra load (or reinforced) tire, or

LL = Light load tire or

C, D, E, F, G = Load range associated with the maximum load a tire can carry at a specified pressure

Maximum Load – Maximum load indicates the maximum load this tire is designed to carry

Maximum Pressure – Maximum pressure indicates the maximum permissible cold tire inflation pressure for this tire

Tire Identification Number (TIN)

The TIN may be found on one or both sides of the tire; however, the date code may only be on one side. Tires with white

sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire. Look for the TIN on the

outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side, then you will find it

on the inboard side of the tire.

EXAMPLE:

DOT MA L9 ABCD 0301

DOT = Department of Transportation

This symbol certifies that the tire is in compliance with the U.S. Department of Transportation tire safety standards and is approved for

highway use

MA = Code representing the tire manufacturing location (two digits)

L9 = Code representing the tire size (two digits)

ABCD = Code used by the tire manufacturer (one to four digits)

03 = Number representing the week in which the tire was manufactured (two digits)

03 means the 3rd week

248

EXAMPLE:

01 = Number representing the year in which the tire was manufactured (two digits)

01 means the year 2001

Prior to July 2000, tire manufacturers were only required to have one number to represent the year in which the tire was manufactured.

Example: 031 could represent the 3rd week of 1981 or 1991

Tire Terminology And Definitions

Term

Definition

The vehicle B-Pillar is the structural member of the body located behind the front

door.

B-Pillar

Cold tire inflation pressure is defined as the tire pressure after the vehicle has not

been driven for at least three hours, or driven less than 1 mile (1.6 km) after sitting

for a minimum of three hours. Inflation pressure is measured in units of PSI (pounds

per square inch) or kPa (kilopascals).

Cold Tire Inflation Pressure

The maximum inflation pressure is the maximum permissible cold tire inflation

pressure for this tire. The maximum inflation pressure is molded into the sidewall.

Maximum Inflation Pressure

Vehicle manufacturer's recommended cold tire inflation pressure as shown on the

tire placard.

Recommended Cold Tire Inflation Pressure

A label permanently attached to the vehicle describing the vehicle’s loading

capacity, the original equipment tire sizes and the recommended cold tire inflation

pressures.

Tire Placard

249

Tire And Loading Information

Placard

Tire Loading And Tire Pressure

Loading

Note: The proper cold tire inflation

pressure is listed on the driver’s side

B-Pillar or the rear edge of the driver's

side door.

The vehicle maximum load on the tire

must not exceed the load carrying

capacity of the tire on your vehicle. You

will not exceed the tire's load carrying

capacity if you adhere to the loading

conditions, tire size, and cold tire

inflation pressures specified on the Tire

and Loading Information placard in

“Vehicle Loading” in the “Starting And

Operating” section of this manual.

Check the inflation pressure of each tire,

including the spare tire (if equipped), at

least monthly and inflate to the

recommended pressure for your vehicle.

GUID-054900418-high.tif

Note: Under a maximum loaded

vehicle condition, gross axle weight

ratings (GAWRs) for the front and rear

axles must not be exceeded.

Tire And Loading Information

Placard

This placard tells you important

information about the:

For further information on GAWRs,

vehicle loading, and trailer towing, refer

to “Vehicle Loading” in the “Starting

And Operating” section of this manual.

1. Number of people that can be

carried in the vehicle.

0806115150US

Example Tire Placard Location

(Door)

2. Total weight your vehicle can carry.

3. Tire size designed for your vehicle.

To determine the maximum loading

conditions of your vehicle, locate the

statement “The combined weight of

occupants and cargo should never

exceed XXX kg or XXX lbs” on the

Tire and Loading Information placard.

The combined weight of occupants,

cargo/luggage and trailer tongue weight

(if applicable) should never exceed the

weight referenced here.

4. Cold tire inflation pressures for the

front, rear, and spare tires.

0806115151US

Example Tire Placard Location

(B-Pillar)

250

Metric Example For Load Limit

Steps For Determining Correct

Load Limit—

150 lb passengers in your vehicle,

the amount of available cargo and

luggage load capacity is 650 lbs.

(1400-750 (5x150) = 650 lbs.)

For example, if “XXX” amount equals

635 kg and there will be five 68 kg

passengers in your vehicle, the amount

of available cargo and luggage load

capacity is 295 kg (635-340 (5x68) =

295 kg) as shown in step 4.

(1) Locate the statement “The

combined weight of occupants and

cargo should never exceed XXX kg

or XXX lbs.” on your vehicle's

placard.

(5) Determine the combined weight

of luggage and cargo being loaded

on the vehicle. That weight may not

safely exceed the available cargo

and luggage load capacity

Note:

(2) Determine the combined weight

of the driver and passengers that

will be riding in your vehicle.

If your vehicle will be towing a trailer,

load from your trailer will be transferred

to your vehicle. The following table

shows examples on how to calculate

total load, cargo/luggage, and towing

capacities of your vehicle with varying

seating configurations and number and

size of occupants. This table is for

illustration purposes only and may not

be accurate for the seating and load

carry capacity of your vehicle.

calculated in Step 4.

(6) If your vehicle will be towing a

trailer, load from your trailer will be

transferred to your vehicle. Consult

this manual to determine how this

reduces the available cargo and

luggage load capacity of your

vehicle.

(3) Subtract the combined weight

of the driver and passengers from

XXX kg or XXX lbs.

(4) The resulting figure equals the

available amount of cargo and

luggage load capacity. For

example, if “XXX” amount equals

1400 lbs. and there will be five

For the following example, the

combined weight of occupants and

cargo should never exceed 865 lbs

(392 kg).

251

GUID-054900419-high.tif

Warning!

Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use

tires of the recommended load capacity for your vehicle. Never overload them.

252

Tires — General

Information

Tire Inflation Pressures

Unequal tire pressures from one side of

the vehicle to the other can cause the

vehicle to drift to the right or left.

The proper cold tire inflation pressure is

listed on the driver's side B-Pillar or rear

edge of the driver's side door.

Tire Pressure

Always drive with each tire inflated to the

recommended cold tire inflation pressure.

Proper tire inflation pressure is essential

to the safe and satisfactory operation of

your vehicle. Four primary areas are

affected by improper tire pressure:

At least once a month:

Check and adjust tire pressure with a

good quality pocket-type pressure

gauge. Do not make a visual judgement

when determining proper inflation. Tires

may look properly inflated even when

they are under-inflated.

Both under-inflation and over-inflation

affect the stability of the vehicle and can

produce a feeling of sluggish response

or over responsiveness in the steering.

Safety and Vehicle Stability

Economy

Note:

Tread Wear

Inspect tires for signs of tire wear or

visible damage.

Unequal tire pressures from side to

side may cause erratic and

unpredictable steering response.

Ride Comfort

Safety

Unequal tire pressure from side to

side may cause the vehicle to drift left

or right.

Caution!

Warning!

After inspecting or adjusting the tire

pressure, always reinstall the valve stem

cap. This will prevent moisture and dirt

from entering the valve stem, which could

damage the valve stem.

Fuel Economy

Improperly inflated tires are dangerous

and can cause collisions.

Underinflated tires will increase tire

rolling resistance resulting in higher fuel

consumption.

Underinflation increases tire flexing and

can result in overheating and tire failure.

Tread Wear

Overinflation reduces a tire's ability to

cushion shock. Objects on the road and

chuckholes can cause damage that result

in tire failure.

Inflation pressures specified on the

placard are always “cold tire inflation

pressure”. Cold tire inflation pressure is

defined as the tire pressure after the

vehicle has not been driven for at least

three hours, or driven less than 1 mile

(1.6 km) after sitting for a minimum of

three hours. The cold tire inflation

pressure must not exceed the

Improper cold tire inflation pressures

can cause abnormal wear patterns and

reduced tread life, resulting in the need

for earlier tire replacement.

Overinflated or underinflated tires can

affect vehicle handling and can fail

suddenly, resulting in loss of vehicle

control.

Ride Comfort And Vehicle Stability

Proper tire inflation contributes to a

comfortable ride. Over-inflation

produces a jarring and uncomfortable

ride.

Unequal tire pressures can cause

steering problems. You could lose control

of your vehicle.

maximum inflation pressure molded into

the tire sidewall.

253

Check tire pressures more often if

subject to a wide range of outdoor

temperatures, as tire pressures vary

with temperature changes.

Consult an authorized tire dealer for tire

repairs and additional information.

Warning!

Damaged Run Flat tires, or Run Flat

tires that have experienced a loss of

pressure should be replaced

immediately with another Run Flat tire

of identical size and service description

(Load Index and Speed Symbol).

High speed driving with your vehicle under

maximum load is dangerous. The added

strain on your tires could cause them to

fail. You could have a serious collision.

Do not drive a vehicle loaded to the

maximum capacity at continuous speeds

above 75 mph (120 km/h).

Tire pressures change by approximately

1 psi (7 kPa) per 12°F (7°C) of air

temperature change. Keep this in mind

when checking tire pressure inside a

garage, especially in the Winter.

Run Flat Tires — If Equipped

Example: If garage temperature = 68°F

(20°C) and the outside temperature =

32°F (0°C) then the cold tire inflation

pressure should be increased by 3 psi

(21 kPa), which equals 1 psi (7 kPa) for

every 12°F (7°C) for this outside

temperature condition.

Run Flat tires allow you the capability to

drive 50 miles (80 km) at 50 mph

Radial Ply Tires

(80 km/h) after a rapid loss of inflation

pressure. This rapid loss of inflation is

referred to as the Run Flat mode. A Run

Flat mode occurs when the tire inflation

pressure is of/or below 14 psi (96 kPa).

Once a Run Flat tire reaches the run flat

mode it has limited driving capabilities

and needs to be replaced immediately.

A Run Flat tire is not repairable.

Warning!

Tire pressure may increase from 2 to 6 psi

(13 to 40 kPa) during operation. DO NOT

reduce this normal pressure build up or

your tire pressure will be too low.

Combining radial ply tires with other types

of tires on your vehicle will cause your

vehicle to handle poorly. The instability

could cause a collision. Always use radial

ply tires in sets of four. Never combine

them with other types of tires.

Tire Pressures For High Speed

Operation

Note: TPM Sensor must be replaced

after driving the vehicle on a flat tire

condition.

The manufacturer advocates driving at

safe speeds and within posted speed

limits. Where speed limits or conditions

are such that the vehicle can be driven

at high speeds, maintaining correct tire

inflation pressure is very important.

Increased tire pressure and reduced

vehicle loading may be required for

high-speed vehicle operation. Refer to

an authorized tire dealer or original

equipment vehicle dealer for

It is not recommended driving a vehicle

loaded at full capacity or to tow a trailer

while a tire is in the run flat mode.

Tire Repair

If your tire becomes damaged, it may

be repaired if it meets the following

criteria:

See the tire pressure monitoring section

for more information.

The tire has not been driven on when

flat.

The damage is only on the tread

section of your tire (sidewall damage is

not repairable).

recommended safe operating speeds,

loading and cold tire inflation pressures.

The puncture is no greater than a ¼

of an inch (6 mm).

254

Tire pressure - Improper cold tire

inflation pressures can cause uneven

wear patterns to develop across the tire

tread. These abnormal wear patterns

will reduce tread life, resulting in the

need for earlier tire replacement.

Tire Spinning

When stuck in mud, sand, snow, or ice

conditions, do not spin your vehicle's

wheels above 30 mph (48 km/h) or for

longer than 30 seconds continuously

without stopping.

Distance driven.

Performance tires, tires with a speed

rating of V or higher, and Summer tires

typically have a reduced tread life.

Rotation of these tires per the vehicle

scheduled maintenance is highly

recommended.

Warning!

0806104865NA

Tire Tread

Fast spinning tires can be dangerous.

Forces generated by excessive wheel

speeds may cause tire damage or failure.

A tire could explode and injure someone.

Do not spin your vehicle's wheels faster

than 30 mph (48 km/h) for more than

30 seconds continuously when you are

stuck, and do not let anyone near a

1 — Worn Tire

2 — New Tire

These indicators are molded into the

bottom of the tread grooves. They will

appear as bands when the tread depth

becomes a 1/16 of an inch (1.6 mm).

When the tread is worn to the tread

wear indicators, the tire should be

replaced.

Warning!

Tires and the spare tire should be replaced

after six years, regardless of the remaining

tread. Failure to follow this warning can

result in sudden tire failure. You could lose

control and have a collision resulting in

serious injury or death.

spinning wheel, no matter what the speed.

Tread Wear Indicators

Refer to “Replacement Tires” in this

section for further information.

Tread wear indicators are in the original

equipment tires to help you in

determining when your tires should be

replaced.

Life Of Tire

Note: Wheel Valve Stem must be

replaced as well when installing new

tires due to wear and tear in existing

tires.

The service life of a tire is dependent

upon varying factors including, but not

limited to:

Keep dismounted tires in a cool, dry

place with as little exposure to light as

possible. Protect tires from contact with

oil, grease, and gasoline.

Driving style.

255

Tire Types

Replacement Tires

Warning!

All Season Tires — If Equipped

The tires on your new vehicle provide a

balance of many characteristics. They

should be inspected regularly for wear

and correct cold tire inflation pressures.

The manufacturer strongly recommends

that you use tires equivalent to the

originals in size, quality and performance

when replacement is needed. Refer to the

paragraph on “Tread Wear Indicators” in

this section. Refer to the Tire and Loading

Information placard or the Vehicle

All Season tires provide traction for all

seasons (Spring, Summer, Fall, and

Winter). Traction levels may vary

between different all season tires. All

season tires can be identified by the

M+S, M&S, M/S or MS designation on

the tire sidewall. Use all season tires

only in sets of four; failure to do so may

adversely affect the safety and handling

of your vehicle.

Do not use a tire, wheel size, load rating,

or speed rating other than that specified

for your vehicle. Some combinations of

unapproved tires and wheels may change

suspension dimensions and performance

characteristics, resulting in changes to

steering, handling, and braking of your

vehicle. This can cause unpredictable

handling and stress to steering and

suspension components. You could lose

control and have a collision resulting in

serious injury or death. Use only the tire

and wheel sizes with load ratings approved

for your vehicle.

Certification Label for the size designation

of your tire. The Load Index and Speed

Symbol for your tire will be found on the

original equipment tire sidewall.

Summer Or Three Season Tires

— If Equipped

See the Tire Sizing Chart example

found in the “Tire Safety Information”

section of this manual for more

information relating to the Load Index

and Speed Symbol of a tire.

Summer tires provide traction in both

wet and dry conditions, and are not

intended to be driven in snow or on ice.

If your vehicle is equipped with Summer

tires, be aware these tires are not

designed for Winter or cold driving

conditions. Install Winter tires on your

vehicle when ambient temperatures are

less than 40°F (5°C) or if roads are

covered with ice or snow. For more

information, contact an authorized

dealer.

Never use a tire with a smaller load

index or capacity, other than what was

originally equipped on your vehicle. Using

a tire with a smaller load index could result

in tire overloading and failure. You could

lose control and have a collision.

It is recommended to replace the two

front tires or two rear tires as a pair.

Replacing just one tire can seriously

affect your vehicle’s handling. If you

ever replace a wheel, make sure that

the wheel’s specifications match those

of the original wheels.

Failure to equip your vehicle with tires

having adequate speed capability can

result in sudden tire failure and loss of

vehicle control.

It is recommended you contact an

authorized tire dealer or original

equipment dealer with any questions

you may have on tire specifications or

capability. Failure to use equivalent

replacement tires may adversely affect

the safety, handling, and ride of your

vehicle.

Caution!

Summer tires do not contain the all

season designation or mountain/

snowflake symbol on the tire sidewall.

Use Summer tires only in sets of four;

failure to do so may adversely affect the

safety and handling of your vehicle.

Replacing original tires with tires of a

different size may result in false

speedometer and odometer readings.

256

capability on wet or dry surfaces may

be poorer than that of non-studded

tires. Some states prohibit studded

tires; therefore, local laws should be

checked before using these tire types.

Compact Spare Tire — If

Equipped

Warning!

The compact spare is for temporary

emergency use only. You can identify if

your vehicle is equipped with a

Do not use Summer tires in snow/ice

conditions. You could lose vehicle control,

resulting in severe injury or death. Driving

too fast for conditions also creates the

possibility of loss of vehicle control.

Spare Tires — If

Equipped

compact spare by looking at the spare

tire description on the Tire and Loading

Information Placard located on the

driver’s side door opening or on the

sidewall of the tire. Compact spare tire

descriptions begin with the letter “T” or

“S” preceding the size designation.

Example: T145/80D18 103M.

Note: For vehicles equipped with Tire

Service Kit instead of a spare tire,

please refer to “Tire Service Kit” in “In

Case Of Emergency” for further

information.

Snow Tires

Some areas of the country require the use

of snow tires during the Winter. Snow tires

can be identified by a “mountain/

T, S = Temporary Spare Tire

Caution!

snowflake” symbol on the tire sidewall.

Since this tire has limited tread life, the

original equipment tire should be

repaired (or replaced) and reinstalled on

your vehicle at the first opportunity.

If you need snow tires,

select tires equivalent

in size and type to the

original equipment

tires. Use snow tires

Because of the reduced ground clearance,

do not take your vehicle through an

automatic car wash with a compact or

limited use temporary spare installed.

Damage to the vehicle may result.

Do not install a wheel cover or attempt

to mount a conventional tire on the

compact spare wheel, since the wheel

is designed specifically for the compact

spare tire. Do not install more than one

compact spare tire and wheel on the

vehicle at any given time.

only in sets of four;

failure to do so may

Spare Tire Matching Original

Equipped Tire And Wheel — If

Equipped

adversely affect the safety and handling

of your vehicle.

Snow tires generally have lower speed

ratings than what was originally

equipped with your vehicle and should

not be operated at sustained speeds

over 75 mph (120 km/h). For speeds

above 75 mph (120 km/h) refer to

original equipment or an authorized tire

dealer for recommended safe operating

speeds, loading and cold tire inflation

pressures.

Your vehicle may be equipped with a

spare tire and wheel equivalent in look

and function to the original equipment

tire and wheel found on the front or rear

axle of your vehicle. This spare tire may

be used in the tire rotation for your

vehicle. If your vehicle has this option,

refer to an authorized tire dealer for the

recommended tire rotation pattern.

While studded tires improve

performance on ice, skid and traction

257

Do not install a wheel cover or attempt

to mount a conventional tire on the

collapsible spare wheel, since the wheel

is designed specifically for the

Limited Use Spare — If

Equipped

Warning!

The limited use spare tire is for

temporary emergency use only. This tire

is identified by a label located on the

limited use spare wheel. This label

contains the driving limitations for this

spare. This tire may look like the original

equipped tire on the front or rear axle of

your vehicle, but it is not. Installation of

this limited use spare tire affects vehicle

handling. Since it is not the same as

your original equipment tire, replace (or

repair) the original equipment tire and

reinstall on the vehicle at the first

opportunity.

collapsible spare tire.

Compact and collapsible spares are for

temporary emergency use only. With these

spares, do not drive more than 50 mph

(80 km/h). Temporary use spares have

limited tread life. When the tread is worn to

the tread wear indicators, the temporary

use spare tire needs to be replaced. Be

sure to follow the warnings, which apply to

your spare. Failure to do so could result in

spare tire failure and loss of vehicle control.

Warning!

Compact and Collapsible spares are for

temporary emergency use only. With these

spares, do not drive more than 50 mph

(80 km/h). Temporary use spares have

limited tread life. When the tread is worn to

the tread wear indicators, the temporary

use spare tire needs to be replaced. Be

sure to follow the warnings, which apply to

your spare. Failure to do so could result in

spare tire failure and loss of vehicle control.

Collapsible Spare Tire — If

Equipped

The collapsible spare is for temporary

emergency use only. You can identify if

your vehicle is equipped with a

Warning!

Full Size Spare — If Equipped

collapsible spare by looking at the

spare tire description on the Tire and

Loading Information Placard located on

the driver’s side door opening or on the

sidewall of the tire.

Limited use spares are for emergency use

only. Installation of this limited use spare

tire affects vehicle handling. With this tire,

do not drive more than the speed listed on

the limited use spare wheel. Keep inflated

to the cold tire inflation pressures listed on

your Tire and Loading Information Placard

located on the driver’s side B-Pillar or the

rear edge of the driver’s side door. Replace

(or repair) the original equipment tire at the

first opportunity and reinstall it on your

vehicle. Failure to do so could result in loss

of vehicle control.

The full size spare is for temporary

emergency use only. This tire may look

like the originally equipped tire on the

front or rear axle of your vehicle, but it is

not. This spare tire may have limited

tread life. When the tread is worn to the

tread wear indicators, the temporary

use full size spare tire needs to be

replaced. Since it is not the same as

your original equipment tire, replace (or

repair) the original equipment tire and

reinstall on the vehicle at the first

opportunity.

Collapsible spare tire description

example: 165/80-17 101P.

Since this tire has limited tread life, the

original equipment tire should be

repaired (or replaced) and reinstalled on

your vehicle at the first opportunity.

Inflate collapsible tire only after the

wheel is properly installed to the

vehicle. Inflate the collapsible tire using

the electric air pump before lowering

the vehicle.

258

Servicing and Maintenance -> Wheels and Tires for Your Fiat 124 Spider 2 Door Second Generation (2016-2020)

Related Topics

Servicing and Maintenance

Popular Owner Manuals

Latest Owner Manuals