Get IN AN EMERGENCY -> REPLACING A WHEEL Guide for Fiat Panda SUV Third Generation (2013-2023)

DASHBOARD FUSEBOX

REPLACING FUSES

The fuse box fig. 113 is located near

the left side of the steering column and

the fuses can be accessed easily from

the lower part of the dashboard.

136) 137) 138) 139) 140) 141)

52)

GENERAL INFORMATION

To facilitate fuse replacement, use the

pliers hooked inside the fuse box lid on

the dashboard left-hand side.

ENGINE COMPARTMENT

FUSEBOX

The fusebox is located next to the

battery: to access the fuses, undo

screw A fig. 112, and lift cover B

upwards.

F1D0093

113

F1D0091

112

The number identifying the electrical

component corresponding to each fuse

is shown on the cover. After replacing

the fuse, make sure you close cover

B on the junction unit.

112

ENGINE COMPARTMENT FUSEBOX

fig. 112

USERS

FUSE

F01

F08

F09

F10

F14

F15

F19

F20

F21

F30

F87

F88

F89

F90

AMPERE

Body Computer node

Passenger compartment fan

Front fog lights

60

40

15

70

7.5

15

5

Horns

Main beam headlights

Heated windscreen

Air conditioning compressor

Front power socket (with or without cigar lighter)

Fuel pump

Blow-by

5

+15 (*) reversing lights

Mirror demisting

7.5

30

5

Heated rear window

Battery charge status sensor

(*)+15 = ignition-operated positive pole

113

DASHBOARD FUSEBOX

fig. 113

USERS

FUSE

AMPERE

F13

5

+15 (*) headlight alignment corrector

+15 (*) Ignition-operated control with inhibition during

engine starting

F31

5

F36

F37

F38

F43

F47

F48

F49

F50

F51

F53

10

7.5

20

7.5

5

+30 (**)

+15 (*) brake pedal switch (NO)

Central door locking

Two-way windscreen washer pump

Front electric window (driver side)

Front electric window (passenger side)

+15 (*)

7.5

+30 (**)

(*)+15 = ignition-operated positive pole

(**)+30 = battery direct positive pole (not ignition-operated)

114

in direct contact with the engine or

to carry out repairs under the vehicle

REPLACING A

WHEEL

WARNING

on boats.

CHANGING PROCEDURE

Proceed as follows:

136) If the replaced fuse blows again,

contact a Fiat Dealership.

142) 143) 144) 145) 146)

137) Never replace a fuse with metal wires

or other material.

stop the car in a position that is not

dangerous for oncoming traffic where

you can change the wheel safely. The

ground must be flat and sufficiently

compact;

JACK

138) Never replace a fuse with another

with a higher amp rating; DANGER OF

FIRE.

Please note that:

the jack weight is 1.76 kg;

the jack requires no adjustment;

139) If a general fuse (MEGA-FUSE,

MIDI-FUSE, MAXI-FUSE) blows contact a

Fiat Dealership.

the jack cannot be repaired and in

the event of a fault it must be replaced

by another genuine one;

switch off the engine, pull up the

handbrake and engage the 1^stgear or

reverse. Wear the reflective safety

jacket (compulsory by law) before

getting out of the car;

140) Before replacing a fuse, make sure

that the ignition key has been removed and

that all the other services are switched off

and/or disengaged.

no tool other than its cranking

device may be fitted on the jack.

open the boot and lift up the mat A

fig. 114;

141) Contact Fiat Dealership if a safety

system (airbags, brakes), engine system

(engine, gearbox) or steering system

general protection fuse blows.

Jack maintenance

prevent any dirt from depositing on

the "worm screw";

keep the "worm screw" lubricated;

never modify the jack.

WARNING

Conditions in which not to use the

jack

52) If you need to wash the engine

compartment, take care not to directly hit

the fuse box and the window wiper motors

with the water jet.

temperature below -40°C

on sandy or muddy ground

on uneven ground

on steep roads

F1D0723

114

in extreme weather conditions:

thunderstorms, typhoons, hurricanes,

blizzards, storms, etc.

115

using the wrench A fig. 115 located

in the tool box, loosen the locking

device, take the tool box B and place it

close to the wheel to be replaced.

Then take the space-saver wheel C.

For the Panda VAN and Panda 4x4

versions, the jack and the tools can be

located under the passenger side

front seat;

position the jack under the car, near

the wheel to be changed;

fit handle D fig. 117 into the housing

in device A, operate the jack and raise

the vehicle until the wheel is a few

centimetres from the ground;

operate the device A fig. 117 to

extend the jack until the top of the jack

B fig. 118 fits correctly into the side

remove the wheel cap after

loosening the 3 fixing bolts and finally

loosen the fourth bolt and extract

the wheel (only for versions with wheel

caps fixed by bolts);

member C (next to the mark

side member);

on the

make sure the contact surfaces

between space-saver spare wheel and

hub are clean so that the fastening

bolts will not come loose;

A

B

fit the space-saver wheel by

inserting the first bolt for two threads

into the hole closest to the valve;

take the wrench A fig. 116 and fully

tighten the fixing bolts;

C

F1D0075

117

F1D0073

115

operate the jack handle D fig. 117 to

lower the car. Then extract the jack;

take the wrench A fig. 116 and

loosen the fixing bolts by about one

turn;

53)

use the wrench A fig. 116 to fully

tighten the bolts, passing alternately

from one bolt to the opposite one;

when replacing a wheel with alloy

rim it is advisable to place it upside

down, with the aesthetic part facing

upwards.

F1D0076

118

alert any bystander that the car is

about to be raised; all persons should

be kept away from the car and nobody

must touch it until it has been lowered;

F1D0074

116

REFITTING THE

STANDARD WHEEL

use the wrench provided to fully

tighten the bolts, passing alternately

from one bolt to the opposite one;

WARNING

54)

reinsert the press-fitted hub cap,

making sure that the reference hole on

the wheel is aligned with the reference

pin on the cap.

Following the procedure described

previously, raise the vehicle and remove

the space-saver wheel.

142) The space-saver wheel (for

versions/markets where provided) is

specific to your car, do not use it on other

models, or use the space-saver wheel

of other models on your car. The

space-saver wheel must only be used in

the event of an emergency. Never use it for

more than strictly necessary and never

exceed 80 km/h. On the space-saver

wheel there is an orange label,

summarising the main warnings regarding

space-saver wheel usage restrictions.

Never remove or cover the label. The label

contains the following indications in four

languages: "Warning! For temporary use

only! 80 km/h max! Replace with standard

wheel as soon as possible. Never cover

this indication." Never apply a wheel cap

on a space-saver wheel.

Versions with steel wheels

Proceed as follows:

NOTE If it is not fitted correctly, the hub

cap may detach when the vehicle is

running.

make sure the contact surfaces

between standard wheel and hub are

clean so that the fastening bolts will not

come loose;

At the end of the operation

stow the space-saver wheel in the

compartment provided in the luggage

compartment;

fit the standard wheel by inserting

the first bolt by 2 threads into the hole

closest to the inflation valve;

insert the jack and the other tools in

the container;

fit the hub cap, aligning the crescent

hole with the bolt already fitted, then

fit the other bolts;

arrange the container and tools on

the space-saver wheel;

using the wrench provided, tighten

the fastening bolts;

143) Alert other drivers that the car is

stationary in compliance with local

correctly reposition the luggage

compartment mat.

regulations: hazard warning lights, warning

triangle, etc. Any passengers on board

should leave the car, especially if it is

heavily laden. Passengers should stay

away from on-coming traffic while the

wheel is being changed. On hills or uneven

roads, use chocks or appropriate objects

to block the wheels of the vehicle.

lower the vehicle and remove the

jack;

use the wrench provided to fully

tighten the bolts, passing alternately

from one bolt to the opposite one.

Versions with alloy rims

Proceed as follows:

insert the wheel on the hub and use

the spanner provided to tighten the

bolts;

lower the vehicle and remove the

jack;

117

IN AN EMERGENCY -> REPLACING A WHEEL for Your Fiat Panda SUV Third Generation (2013-2023)

Related Topics

Popular Owner Manuals

Latest Owner Manuals