Get IN AN EMERGENCY -> REPLACING FUSES Guide for Fiat Panda SUV Third Generation (2013-2023)

DASHBOARD FUSEBOX

REPLACING FUSES

The fuse box fig. 113 is located near

the left side of the steering column and

the fuses can be accessed easily from

the lower part of the dashboard.

136) 137) 138) 139) 140) 141)

52)

GENERAL INFORMATION

To facilitate fuse replacement, use the

pliers hooked inside the fuse box lid on

the dashboard left-hand side.

ENGINE COMPARTMENT

FUSEBOX

The fusebox is located next to the

battery: to access the fuses, undo

screw A fig. 112, and lift cover B

upwards.

F1D0093

113

F1D0091

112

The number identifying the electrical

component corresponding to each fuse

is shown on the cover. After replacing

the fuse, make sure you close cover

B on the junction unit.

112

ENGINE COMPARTMENT FUSEBOX

fig. 112

USERS

FUSE

F01

F08

F09

F10

F14

F15

F19

F20

F21

F30

F87

F88

F89

F90

AMPERE

Body Computer node

Passenger compartment fan

Front fog lights

60

40

15

70

7.5

15

5

Horns

Main beam headlights

Heated windscreen

Air conditioning compressor

Front power socket (with or without cigar lighter)

Fuel pump

Blow-by

5

+15 (*) reversing lights

Mirror demisting

7.5

30

5

Heated rear window

Battery charge status sensor

(*)+15 = ignition-operated positive pole

113

DASHBOARD FUSEBOX

fig. 113

USERS

FUSE

AMPERE

F13

5

+15 (*) headlight alignment corrector

+15 (*) Ignition-operated control with inhibition during

engine starting

F31

5

F36

F37

F38

F43

F47

F48

F49

F50

F51

F53

10

7.5

20

7.5

5

+30 (**)

+15 (*) brake pedal switch (NO)

Central door locking

Two-way windscreen washer pump

Front electric window (driver side)

Front electric window (passenger side)

+15 (*)

7.5

+30 (**)

(*)+15 = ignition-operated positive pole

(**)+30 = battery direct positive pole (not ignition-operated)

114

in direct contact with the engine or

to carry out repairs under the vehicle

REPLACING A

WHEEL

WARNING

on boats.

CHANGING PROCEDURE

Proceed as follows:

136) If the replaced fuse blows again,

contact a Fiat Dealership.

142) 143) 144) 145) 146)

137) Never replace a fuse with metal wires

or other material.

stop the car in a position that is not

dangerous for oncoming traffic where

you can change the wheel safely. The

ground must be flat and sufficiently

compact;

JACK

138) Never replace a fuse with another

with a higher amp rating; DANGER OF

FIRE.

Please note that:

the jack weight is 1.76 kg;

the jack requires no adjustment;

139) If a general fuse (MEGA-FUSE,

MIDI-FUSE, MAXI-FUSE) blows contact a

Fiat Dealership.

the jack cannot be repaired and in

the event of a fault it must be replaced

by another genuine one;

switch off the engine, pull up the

handbrake and engage the 1^stgear or

reverse. Wear the reflective safety

jacket (compulsory by law) before

getting out of the car;

140) Before replacing a fuse, make sure

that the ignition key has been removed and

that all the other services are switched off

and/or disengaged.

no tool other than its cranking

device may be fitted on the jack.

open the boot and lift up the mat A

fig. 114;

141) Contact Fiat Dealership if a safety

system (airbags, brakes), engine system

(engine, gearbox) or steering system

general protection fuse blows.

Jack maintenance

prevent any dirt from depositing on

the "worm screw";

keep the "worm screw" lubricated;

never modify the jack.

WARNING

Conditions in which not to use the

jack

52) If you need to wash the engine

compartment, take care not to directly hit

the fuse box and the window wiper motors

with the water jet.

temperature below -40°C

on sandy or muddy ground

on uneven ground

on steep roads

F1D0723

114

in extreme weather conditions:

thunderstorms, typhoons, hurricanes,

blizzards, storms, etc.

115

using the wrench A fig. 115 located

in the tool box, loosen the locking

device, take the tool box B and place it

close to the wheel to be replaced.

Then take the space-saver wheel C.

For the Panda VAN and Panda 4x4

versions, the jack and the tools can be

located under the passenger side

front seat;

position the jack under the car, near

the wheel to be changed;

fit handle D fig. 117 into the housing

in device A, operate the jack and raise

the vehicle until the wheel is a few

centimetres from the ground;

operate the device A fig. 117 to

extend the jack until the top of the jack

B fig. 118 fits correctly into the side

remove the wheel cap after

loosening the 3 fixing bolts and finally

loosen the fourth bolt and extract

the wheel (only for versions with wheel

caps fixed by bolts);

member C (next to the mark

side member);

on the

make sure the contact surfaces

between space-saver spare wheel and

hub are clean so that the fastening

bolts will not come loose;

A

B

fit the space-saver wheel by

inserting the first bolt for two threads

into the hole closest to the valve;

take the wrench A fig. 116 and fully

tighten the fixing bolts;

C

F1D0075

117

F1D0073

115

operate the jack handle D fig. 117 to

lower the car. Then extract the jack;

take the wrench A fig. 116 and

loosen the fixing bolts by about one

turn;

53)

use the wrench A fig. 116 to fully

tighten the bolts, passing alternately

from one bolt to the opposite one;

when replacing a wheel with alloy

rim it is advisable to place it upside

down, with the aesthetic part facing

upwards.

F1D0076

118

alert any bystander that the car is

about to be raised; all persons should

be kept away from the car and nobody

must touch it until it has been lowered;

F1D0074

116

REFITTING THE

STANDARD WHEEL

use the wrench provided to fully

tighten the bolts, passing alternately

from one bolt to the opposite one;

WARNING

54)

reinsert the press-fitted hub cap,

making sure that the reference hole on

the wheel is aligned with the reference

pin on the cap.

Following the procedure described

previously, raise the vehicle and remove

the space-saver wheel.

142) The space-saver wheel (for

versions/markets where provided) is

specific to your car, do not use it on other

models, or use the space-saver wheel

of other models on your car. The

space-saver wheel must only be used in

the event of an emergency. Never use it for

more than strictly necessary and never

exceed 80 km/h. On the space-saver

wheel there is an orange label,

summarising the main warnings regarding

space-saver wheel usage restrictions.

Never remove or cover the label. The label

contains the following indications in four

languages: "Warning! For temporary use

only! 80 km/h max! Replace with standard

wheel as soon as possible. Never cover

this indication." Never apply a wheel cap

on a space-saver wheel.

Versions with steel wheels

Proceed as follows:

NOTE If it is not fitted correctly, the hub

cap may detach when the vehicle is

running.

make sure the contact surfaces

between standard wheel and hub are

clean so that the fastening bolts will not

come loose;

At the end of the operation

stow the space-saver wheel in the

compartment provided in the luggage

compartment;

fit the standard wheel by inserting

the first bolt by 2 threads into the hole

closest to the inflation valve;

insert the jack and the other tools in

the container;

fit the hub cap, aligning the crescent

hole with the bolt already fitted, then

fit the other bolts;

arrange the container and tools on

the space-saver wheel;

using the wrench provided, tighten

the fastening bolts;

143) Alert other drivers that the car is

stationary in compliance with local

correctly reposition the luggage

compartment mat.

regulations: hazard warning lights, warning

triangle, etc. Any passengers on board

should leave the car, especially if it is

heavily laden. Passengers should stay

away from on-coming traffic while the

wheel is being changed. On hills or uneven

roads, use chocks or appropriate objects

to block the wheels of the vehicle.

lower the vehicle and remove the

jack;

use the wrench provided to fully

tighten the bolts, passing alternately

from one bolt to the opposite one.

Versions with alloy rims

Proceed as follows:

insert the wheel on the hub and use

the spanner provided to tighten the

bolts;

lower the vehicle and remove the

jack;

117

144) The vehicle's driving characteristics

will be modified with the space-saver wheel

fitted. Avoid violent acceleration and

146) If the hub cap is not fitted correctly, it

may come off when the car is travelling.

Never tamper with the inflation valve. Never

introduce tools of any kind between rim

and tyre. Check tyre and space-saver

wheel pressures regularly, complying with

the values given in the "Technical

Fix&Go KIT

braking, abrupt steering and fast cornering.

The overall duration of the space-saver

wheel is about 3000 km, after which the

relevant tyre must be replaced with another

one of the same type. Never install a

traditional tyre on a rim designed to be

used as a space-saver wheel. Have the

wheel repaired and refitted as soon as

possible. Using two or more space-saver

wheels at the same time is forbidden.

Do not apply grease to the bolt threads

before fitting: they could come unscrewed.

147) 148)

55)

specifications" chapter.

DESCRIPTION

The Fix&Go quick tyre repair kit fig. 119

is located in the boot, inside a

dedicated container and consists of:

WARNING

53) When turning the jack handle make

sure that it can turn freely without scraping

your hand against the ground. The moving

components of the jack ("worm screw"

and joints) can also cause injuries: avoid

touching them. If you come into contact

with lubricating grease, clean yourself

thoroughly.

one cartridge A containing sealant

and fitted with: transparent tube for

injecting the sealant D and sticker

C with the wording “Max 80 km/h” to

be placed in a clearly visible position

(e.g. on the dashboard) after repairing

the tyre;

145) The jack is a tool developed and

designed only for changing a wheel, if a

tyre gets punctured or damaged, on the

vehicle with which it is supplied or on other

vehicles of the same model. Any other

use, e.g. to jack up other vehicle models or

different things, is strictly prohibited. Never

use for maintenance or repair activities

under the car or to exchange the

summer/winter wheels and vice versa.

Never go under the raised vehicle. If any

work under the vehicle is necessary,

contact the Fiat Service Network. Incorrect

positioning of the jack may cause the

raised vehicle to fall: use only in the

positions indicated. Do not use the jack for

loads higher than the one shown on its

label. Never start the engine with vehicle

raised. If the vehicle is raised more than

necessary, everything can become more

unstable, with the risk of the vehicle

dropping violently. Thus, lift the vehicle only

as needed in order to access the spare

wheel.

54) Contact a Fiat Dealership as soon as

possible to have the correct tightening

of the wheel bolts checked.

one compressor B;

one leaflet containing instructions for

using the kit;

a pair of gloves located in the hose

compartment of the cartridge D.

F1D0709

119

118

REPAIR PROCEDURE

Proceed as follows:

stop the car in a position that is not

dangerous for oncoming traffic where

you can carry out the procedure safely.

The ground must be flat and sufficiently

compact;

stop the engine, engage the hazard

warning lights and the parking brake;

F1D0710

120

F1D0712

122

wear the reflective safety jacket

before getting out of the car (anyway

comply with the laws in force in the

country you are driving in);

operate the compressor by pressing

the ON-OFF button E fig. 121. When

the pressure shown in the "Wheels"

paragraph in the “Technical data”

chapter or on the specific label appears

on the pressure gauge G, stop the

compressor by pressing the ON-OFF

button E again;

If the pressure gauge G fig. 121

indicates a pressure lower than 1.8 bar

/ 26 psi 15 minutes after starting the

compressor, switch off the compressor,

disconnect the sealing fluid tube D

from the tyre valve and remove the

cartridge A from the compressor fig.

122.

insert the cartridge A containing the

sealant in the proper compartment of

the compressor B, pressing it down

hard fig. 119. Remove the adhesive

speed label C and apply it in a visible

position (fig. 123);

wear the gloves;

remove the cap from the tyre valve

and connect and screw the transparent

tube of the sealing fluid D fig. 119

onto the valve. If a 250 ml cartridge is

present the housing of the transparent

tube is provided with removable ring

to facilitate extraction. Make sure that

the ON-OFF button E fig. 121 is in

the off position (button not pressed);

F1D0711

F1D0713

121

123

disconnect the cartridge A from the

compressor, by pressing the release

button H and lifting the cartridge A

upwards fig. 122.

plug the electric connector F fig. 120

into the 12V socket of the vehicle and

start the vehicle engine;

119

148) IMPORTANT: Do not exceed 80 km/h.

Avoid sudden acceleration or braking.

The kit provides a temporary repair,

therefore the tyre must be examined and

repaired by a specialist as soon as

possible. Before using the kit, ensure that

the tyre is not excessively damaged and

that the rim is in good condition, otherwise

do not use it and call roadside assistance.

Do not remove foreign bodies from the

tyre. Do not let the compressor turned on

for more than 20 consecutive minutes -

overheating hazard.

Move the vehicle by approximately 10

m to promote the distribution of

INFLATION PROCEDURE

Proceed as follows:

sealant; stop the vehicle safely, operate

the handbrake and restore pressure

using the black inflation pipe I fig. 124

to reach the required pressure. If also in

this case, the pressure is lower than

1.8 bar / 26 psi 15 minutes after turning

on, do not resume driving but contact

a Fiat Dealership.

stop the vehicle safely, as shown

above, and operate the handbrake;

extract the black inflation tube I fig.

124 and screw it firmly onto the tyre

valve. Follow the instructions shown in

fig. 120 and fig. 124.

Press the air release button J fig. 121 to

adjust any tyre overpressure.

CARTRIDGE

REPLACEMENT

WARNING

Proceed as follows:

only use original Fix&Go cartridges,

which can be purchased from the

Fiat Dealership.

55) The sealant is effective with external

temperatures of between -40°C and

+55°C. The sealant has an expiry date. It is

possible to repair tyres which have been

damaged on tread up to a diameter of

6 mm. Show the cartridge and the label to

the personnel charged with handling the

tyre treated with the tyre repair kit.

to remove the cartridge A fig. 119

press the release button H fig. 122 and

lift it.

F1D0714

124

After driving for about 8 km / 5 miles,

position the car in a safe and suitable

area and engage the handbrake. Take

the compressor and restore pressure

using the black inflation tube I fig. 124.

If the pressure shown is higher than

1.8 bar / 26 psi, restore the pressure

and drive safely to a Fiat Dealership as

soon as possible. If, however, the

pressure is lower than 1.8 bar / 26 psi,

do not resume driving but contact a

Fiat Dealership.

WARNING

147) The information required by the

applicable regulation is indicated on the

Fix&Go kit package label. Carefully read

the label on the cartridge before use, avoid

improper use. The kit should be used by

adults and cannot be used by children.

120

PREPARATION TO JUMP

STARTING

PROCEDURE FOR JUMP

STARTING

JUMP STARTING

149) 150)

IMPORTANT If the procedure below is

carried out incorrectly, it can cause

severe injury to people or damage the

recharging system of one or both

vehicles. Carefully follow the

If the battery is flat, a jump starting can

be performed using the battery and

the cables of another vehicle, or using a

booster battery.

56) 57)

IMPORTANT The positive terminal (+) of

the battery is shielded by a protective

cover. Lift the cover to access the

positive terminal.

If the warning light

remains on

instructions given below.

continuously on the instrument panel,

contact the Fiat Dealership immediately.

Cable connection

Proceed as follows:

Proceed as follows to carry out a jump

starting:

IMPORTANT NOTES

engage the handbrake, move the

Dualogic gear lever to P (Park) or,

for versions with manual gearbox, to

neutral and bring the ignition key to

STOP;

When a booster battery is used, comply

with the utilisation and precaution

instructions specified by the producer.

Do not use the booster battery or

any other source of external supply with

a voltage above 12 V: the battery, the

starter, the alternator and the electrical

system of the vehicle could be

damaged.

connect one end of the cable used

for positive (+) to the positive terminal

(+) of the car with flat battery;

connect the other end of the cable

used for positive (+) to the positive

terminal (+) of the auxiliary battery;

switch off all the other electrical

devices in the car;

if another vehicle is ready for jump

starting, park the vehicle within the

reach of the cables to be used for

starting, operate the handbrake and

make sure that the ignition is

deactivated.

connect one end of the cable used

for negative (–) to the negative terminal

(–) of the auxiliary battery;

Do not attempt jump starting if the

battery is frozen. The battery could

break and explode!

connect the other end of the cable

used for negative (–) to an engine earth

(the visible metal part of the car engine

with flat battery) far from the battery

and the fuel injection system;

IMPORTANT Avoid contact between

the two vehicles since this could cause

a connection to earth and may result

in serious injury to any people nearby.

start the vehicle engine with the

auxiliary battery, let it run for a few

minutes at idling. Start the engine of the

car with flat battery.

121

Cable disconnection

FUEL CUT-OFF

SYSTEM

WARNING

Once the engine has been started,

remove the cables proceeding as

follows:

151)

149) This starting procedure must be

performed by expert personnel because

incorrect actions could cause electrical

discharge of considerable intensity.

Furthermore, battery fluid is poisonous and

corrosive: avoid contact with skin and

eyes. Keep naked flames and lighted

cigarettes away from the battery and do

not cause sparks.

This intervenes in the case of an impact

causing:

disconnect the end of the cable

used for negative (–) from the engine

earth of the car with flat battery;

the interruption of the fuel supply

with the engine consequently cutting

out;

disconnect the other end of the

cable used for negative (–) from the

negative terminal (–) of the auxiliary

battery;

the automatic unlocking of the

doors;

150) Remove any metal objects (e.g. rings,

watches, bracelets), that might cause an

accidental electrical contact and cause

serious injury.

turning on the lights inside the car;

disconnect the end of the cable

used for positive (+) from the positive

terminal (+) of the auxiliary battery;

the switching on of the hazard

warning lights.

disconnect one end of the cable

used for positive (+) from the positive

terminal (+) of the car with flat battery.

If it is often necessary to perform a

jump starting, have the car battery and

the recharging system checked by a

Fiat Dealership.

NOTE Carefully check the vehicle for

fuel leaks, for instance in the engine

compartment, under the vehicle or near

the tank area. After an impact, turn

the ignition key to STOP to prevent the

battery from running down.

WARNING

56) Do not connect the cable to the

negative terminal (–) of the flat battery. The

following spark could lead to battery

explosion and cause serious harm. Only

use the specific earth point; do not use any

other exposed metallic part.

To restore the correct operation of the

vehicle, proceed as follows:

IMPORTANT Any accessories (e.g.

mobile phones, etc.) connected to the

vehicle power sockets draw current

even if they are not used. These

57) Never use a fast battery-charger to

start the engine as this could damage the

electronic systems of your vehicle,

particularly the ignition and engine fuel

supply control units.

turn the ignition key to the MAR

position;

activate the right direction indicator;

devices, if left connected too much time

with engine off, may cause the battery

to drain with following reduction of

its life and/or failure to start the engine.

deactivate the right direction

indicator;

activate the left direction indicator;

deactivate the left direction indicator;

activate the right direction indicator;

122

deactivate the right direction

indicator;

TOWING THE CAR

152) 153) 154) 155) 156)

activate the left direction indicator;

deactivate the left direction indicator;

The tow hook, if is supplied with the

car, is housed in the tool box, under the

mat in the luggage compartment.

turn the ignition key to STOP and

then to MAR.

LPG versions: in the event of an

impact, petrol supply is immediately

cut-off, the LPG safety valves are

closed and the injection is interrupted,

switching off the engine.

ATTACHING THE TOW

HOOK

Manually remove cap A fig. 125 (front

bumper) or A fig. 126 (for versions/

markets, where provided) on the rear

bumper, pressing the lower part, take

the tow hook B from its housing in

the tool box and tighten it completely

on the front or rear threaded pin.

F1D0095

126

Versions with Dualogic

transmission

Natural Power versions: in the event

of an impact, the power supply is

immediately cut off, causing engine

switching off.

Make sure that the transmission is in

neutral (N) (checking that the car moves

when pushed) and proceed in the

same way as for towing a normal car

with a manual transmission. If the

gearbox cannot be put in neutral, do

not tow the car and contact a Fiat

Dealership.

WARNING

151) If, after an impact, you smell fuel or

notice leaks from the fuel system, do

not reactivate the system to avoid the risk

of fire.

Panda Cross 4x4 and Panda 4x4

versions

The car can only be towed in one of the

following ways (and always with the

engine off, gear set to neutral and

handbrake released):

F1D0094

125

with all the wheels on the road

surface;

with the front (or rear) wheels raised

or resting on an emergency vehicle

and the rear (or front) wheels resting on

a specific trolley;

123

IN AN EMERGENCY -> REPLACING FUSES for Your Fiat Panda SUV Third Generation (2013-2023)

Related Topics

Popular Owner Manuals

Latest Owner Manuals