Get STARTING AND DRIVING -> DUALDRIVE ELECTRIC POWER STEERING Guide for Fiat Panda SUV Third Generation (2013-2023)

SIDE BAGS (Side bag -

Window bag)

The deployment of side bags in the

event of side impacts of low severity is

not required.

To help increase occupants protection

in the event of a side impact, the car

is equipped with front side bags (for

versions/markets, where provided) and

window bag (for versions/markets,

where provided).

In the event of a side impact, the

system provides best protection if the

passenger sits on the seat in a correct

position, thus allowing correct window

bag deployment.

The window bag is not available for the

VAN version.

Side bags protect occupants from

side-on crashes of medium/high

severity by placing the bag between the

occupant and the internal parts of the

side structure of the vehicle.

103) 104) 105) 106) 107) 108) 109) 110) 111) 112)

113) 114) 115)

Non-activation of side bags in other

types of collisions (front collisions, rear

shunts, roll-overs, etc.) is not a system

malfunction.

Important notes

Do not wash the seats with water or

pressurised steam (wash by hand or at

automatic seat washing stations).

The front airbags and/or side bags may

be deployed in the event of sharp

impacts to the underbody of the car

(e.g. impact with steps, pavements,

potholes or road bumps etc.).

When the airbag deploys it emits a

small amount of dust: the dust is

harmless and does not indicate the

beginning of a fire. The dust may irritate

the skin and eyes however: in this

case, wash with neutral soap

Side bags

(for versions/markets, where provided)

F1D0066

79

These comprise two types of bags

located in the front seat backrests fig.

79 which protect the pelvic, chest

and shoulder area of the occupants in

the event of a side impact of

medium-high severity.

Window bag

This consists of two "curtain" bags

housed behind the roof side lining fig.

80 and covered with trims that protect

the heads of front and rear occupants

in the event of a side impact.

and water.

Airbag checking, repair and

F1D0067

80

replacement must be carried out at a

Fiat Dealership.

87

101) When there is an active passenger

airbag, DO NOT install rearward facing

child restraint systems on the front seat.

Deployment of the airbag in a crash could

cause fatal injuries to the child regardless

of the severity of the collision. Therefore,

always deactivate the passenger side

airbag when a rearward facing child

restraint system is installed on the front

passenger seat. The front passenger seat

must also be positioned back as far as

possible in order to prevent the child

restraint system from coming into contact

with the dashboard. Immediately reactivate

the passenger airbag as soon as the child

restraint system has been removed.

107) In the event of “yellow”

light failure, the “red” warning light

warning

If the car is scrapped, have the airbag

system deactivated at a Fiat Dealership.

Pretensioners and airbags are

switches on and, for versions/markets

where provided, the explosive charges of

the passenger airbag and the side bags

are deactivated. When the "red" warning

light is on, before proceeding contact a Fiat

Dealership to have the system immediately

checked (see previous warning).

deployed in different ways on the basis

of the type of collision. Failure to

activate one or more of the devices

does not indicate a system malfunction.

108) On vehicles with side bags, do not

cover the front seat backrests with extra

covers.

WARNING

109) Do not travel carrying objects in your

lap, in front of your chest or between

your lips (pipe, pencils, etc.): they could

cause severe injury if the airbag is

deployed.

99) Do not apply stickers or other objects

on the steering wheel, on the dashboard in

the passenger side airbag area, on the

side upholstery on the roof and on the

seats. Never put objects (e.g. mobile

phones) on the passenger's side

dashboard since they could interfere with

correct inflation of the airbag and also

cause serious injury to the passengers.

102) To deactivate the airbags using the

instrument panel menu, see the description

in the "Knowing the instrument panel"

chapter, "Setup Menu" paragraph.

110) If the car has been stolen or in the

case of attempt to steal it, if it has been

subjected to vandalism or floods, have the

airbag system checked by a Fiat

Dealership.

103) Do not affix rigid objects to the

garment hooks or support handles.

104) Do not rest your head, arms or

elbows on the door, windows or the area in

which the window bag is located to avoid

possible injury during airbag inflation.

100) Always drive with your hands on the

rim of the steering wheel so that the airbag

can inflate freely if required. Do not drive

bent over the steering wheel, but rather sit

upright with your back firmly resting against

the seat back.

105) Never lean your head, arms or

elbows out of the window.

106) If, when the ignition device is turned

to MAR, the

warning light does not

switch on or stays on whilst driving, a fault

may have occurred in the restraint

systems. In this case the airbags or

pretensioners may not be deployed in an

impact or, in a lower number of cases, they

may be deployed accidentally. Contact a

Fiat Dealership immediately to have the

system checked.

88

111) The airbags may also be deployed

when the car is not moving, if the key is in

the ignition and turned to MAR-ON or

when the engine is off, if the car is hit by

another moving car. Therefore, even if the

vehicle is stationary, when an active front

passenger airbag is fitted, DO NOT install

rearward facing child restraint systems

on the front passenger seat. Deployment of

the airbag following an impact could cause

fatal injuries to the child. Therefore, always

deactivate the passenger side airbag

when a rearward facing child restraint

system is installed on the front passenger

seat. The front passenger seat must also

be positioned back as far as possible in

order to prevent the child restraint system

from coming into contact with the

dashboard. Immediately reactivate the

passenger airbag as soon as the child

restraint system has been removed. Also

remember that, if the key is turned to

STOP, none of the safety devices (airbags

or pretensioners) will be deployed in the

event of collision. Non-deployment in such

cases does not indicate a system

112) The airbag warning light

indicates

114) The airbag does not replace seat

belts but increases their efficiency.

Because front airbags are not deployed for

low-speed crashes, side collisions,

rear-end shunts or rollovers, occupants are

protected, in addition to any side bags,

only by their seat belts, which must

therefore always be fastened.

the passenger protection status. If the

warning light is off, the passenger side

protection is activated. It can be

deactivated from the menu, in which case

the warning light comes on. When the

car is started (ignition key in MAR position),

the warning light comes on for approx. 8

seconds, provided that at least 5 seconds

have elapsed from the previous switching

off. If this does not happen please contact

a Fiat Dealership. If the car is switched

off/on again in less than 5 seconds the

warning light may remain off. In this case,

to check correct warning light operation,

switch the car off, wait at least 5 seconds

and switch on again. During the first 8

seconds, the activation of the warning light

does not actually show the passenger

protection status, but only checks its

correct operation. The warning light may

light up with various intensity levels

depending on the car conditions. The

intensity may also vary during the same key

cycle. (The warning light is tested also for

markets where the passenger protection

deactivation function is not provided,

and the warning light switches on for less

than one second when the key is turned to

MAR, then switches off again.)

115) If the “red”

warning light does not

switch on for a few seconds when the

key is turned to MAR, there may be a fault

with the “red” warning light. In this case,

after a few seconds, the

warning light

starts flashing. Contact a Fiat Dealership

immediately to have the system checked.

malfunction.

113) The airbag deployment threshold is

higher than that of the pretensioners.

For collisions in the range between the two

thresholds, it is normal for only the

pretensioners to be activated.

89

STARTING AND DRIVING

Let’s get to the "heart" of the vehicle:

seeing how you can exploit all of its

potential to the full.

STARTING THE ENGINE................. 91

WHEN PARKED .............................. 92

MANUAL TRANSMISSION.............. 93

DUALOGIC TRANSMISSION........... 94

MODE SELECTOR.......................... 95

We’ll look at how to drive it safely in any

situation, so that it can be a welcome

companion, with our comfort and

our wallets in mind.

DUALDRIVE ELECTRIC POWER

STEERING ...................................... 96

ECO FUNCTION ............................. 97

START&STOP SYSTEM .................. 98

PARKING SENSORS....................... 99

REFUELLING THE VEHICLE ...........100

TOWING TRAILERS ........................103

90

Diesel versions

VERSIONS WITH

DUALOGIC

TRANSMISSION

STARTING THE

ENGINE

Proceed as follows:

engage the handbrake, put the gear

lever into neutral and turn the ignition

118)

Engine starting is allowed both with a

gear engaged and with the gearbox

in neutral (N).

116) 117)

key to MAR: the warning lights

on the instrument panel will turn

and

38) 39) 40) 41)

on;

However, the brake pedal must always

be pressed first if neutral is not

engaged. It is therefore advisable to

place the gear lever in neutral (N) before

starting the engine.

wait for the warning lights

to turn off and then fully depress

and

Before starting the engine, adjust the

seat, the interior rear view mirrors,

the door mirrors and fasten the seat

belt correctly.

the clutch pedal without pressing the

accelerator;

turn the ignition key to the AVV

position as soon as the warning light

turns off. Release the ignition key as

soon as the engine starts.

Never press the accelerator pedal for

starting the engine.

LPG AND NATURAL

POWER VERSIONS

The engine always starts up on petrol

independently of the previously

selected mode.

VERSIONS WITH MANUAL

TRANSMISSION

IMPORTANT If the engine does not

start at the first attempt, return the

ignition key to STOP before repeating

the procedure. If, with the ignition

key on MAR, the instrument panel

Petrol versions

42)

Proceed as follows:

engage the handbrake and put the

gear lever in neutral. For 0.9 TwinAir

and 0.9 TwinAir Turbo versions

engage the handbrake and place the

gear lever in neutral or fully press the

clutch pedal if a gear other than neutral

is engaged;

SWITCHING OFF THE

ENGINE

warning lights

and

stay on (for

43)

petrol versions only), it is advisable to

turn the key to STOP and then back to

Turn the ignition key to STOP while the

engine is idling.

MAR. If the

warning light remains

on, try with the other keys provided

with the car. Contact a Fiat Dealership if

you still cannot start the engine.

IMPORTANT After a demanding drive,

before turning the engine off you should

allow it to idle to allow the temperature

in the engine compartment to

decrease.

for all versions (except 0.9

TwinAir and 0.9 TwinAir Turbo) fully

depress the clutch pedal without

touching the accelerator;

turn the ignition key to AVV and

release it as soon as the engine starts.

91

40) When the engine is switched off never

leave the key turned to MAR-ON to prevent

useless current absorption from draining

the battery.

WHEN PARKED

WARNING

When parking and leaving the car,

proceed as follows:

engage a gear (1^stgear if facing

uphill or reverse if facing downhill) and

leave the wheels turned;

41) Never bump start the engine by

pushing, towing or coasting downhill. This

could cause fuel to flow into the catalytic

converter and damage it beyond repair.

116) It is dangerous to run the engine in

enclosed areas. The engine consumes

oxygen and engine exhaust contains

carbon dioxide, carbon monoxide and

other toxic gasses.

stop the engine and engage the

handbrake;

42) There must therefore always be some

petrol in the tank to protect the petrol

pump and to guarantee temporary

switching from LPG or Methane to petrol

operation, if high performance is required.

117) Remember that the power brake and

electrical power steering are not

operational until the engine is started,

therefore a greater effort will be required to

press the brake pedal or turn the steering

wheel.

always remove the ignition key.

Block the wheels with a wedge or a

stone if the car is parked on a steep

slope.

43) A quick burst on the accelerator

before turning off the engine serves

absolutely no practical purpose, it wastes

fuel and is especially damaging to

turbocharged engines.

On versions equipped with Dualogic

transmission, wait for the letter P to be

displayed before releasing the brake

pedal.

118) If the engine fails to start with a gear

engaged, the potentially dangerous

situation due to the fact that the gearbox is

automatically placed in neutral will be

signalled by an acoustic signal.

IMPORTANT NEVER leave the car with

the gearbox in neutral (or, on versions

equipped with Dualogic transmission,

before placing the gear lever at P).

WARNING

Handbrake

38) If the warning light flashes for 60

seconds after starting or during an

197) 198) 199)

extended towing period, this indicates a

problem in the glow plug pre-heating

system. You can use the vehicle as usual if

the engine starts but you should contact

a Fiat Dealership as soon as possible.

The handbrake lever is located between

the front seats.

Handbrake engagement: pull lever A

fig. 81 upwards until the vehicle is

braked.

39) It is advisable not to demand

maximum performance from your car (e.g.

excessive acceleration, long distances at

maximum rpm, excessively intense braking,

etc.) when it is first used.

92

IMPORTANT Reverse can only be

engaged when the car is completely

stationary. With the engine running, wait

for at least 2 seconds with the clutch

pedal fully pressed before engaging

reverse to prevent damage to the gears

and grating.

MANUAL

TRANSMISSION

122)

44)

To engage the gears, fully depress the

clutch pedal and put the gear lever

into the required position (the diagram

is shown on the knob fig. 82).

B

A

IMPORTANT The clutch pedal should

be used only for gear changes. Do

not drive with your foot resting on the

clutch pedal, however lightly. For

versions/markets where provided, the

electronic clutch control could cut

in, interpreting the incorrect driving style

as a fault.

F1D0146

81

Handbrake disengagement: slightly

raise lever A and hold button B

A

pressed, checking that the

warning

light switches off in the instrument

panel.

WARNING

F1D0069

82

119) Never leave children unattended in

the car. Always remove the key from the

ignition when leaving the car and take

it with you.

For 0.9 TwinAir, 0.9 TwinAir Turbo and

1.2 8V 69 HP versions, to engage

reverse gear R from neutral, lift the ring

A fig. 82 located under the knob and

at the same time shift the lever to

the right and back.

122) Press the clutch pedal fully to change

gears correctly. It is therefore essential

that there is nothing under the pedals:

make sure the mats are lying flat and do

not get in the way of the pedals.

120) The car should be braked after a few

clicks of the lever, if it is not, contact a

Fiat Dealership to have it adjusted.

WARNING

For 1.3 16V MultiJet version: to engage

reverse gear R from neutral position,

move the lever to the right and then

back.

121) In the case of parking manoeuvres on

roads on a gradient, the front wheels

must be steered towards the pavement

(when parking downhill), or in the opposite

direction if the vehicle is parked uphill.

Block the wheels with a wedge or a stone if

the car is parked on a steep slope.

44) Do not drive with your hand resting on

the gear lever as the force exerted, even

if slight, could lead over time to premature

wear of the gearbox internal components.

93

The unstable positions, in other words

those that are abandoned as soon

as the lever is released, are the

positions for requesting a higher gear

(+), requesting a lower gear (–) and

requesting automatic operating mode

(A/M).

AUTOMATIC MODE (AUTO)

DUALOGIC

TRANSMISSION

(for versions/markets, where provided)

Proceed as follows:

press the brake pedal;

start the engine;

if AUTO is not on the display, move

the shift lever A fig. 83 to A/M to select

AUTOMATIC mode;

45)

The car may be equipped with an

electronically controlled manual

transmission known as "Dualogic"

which allows two operating logics:

MANUAL and AUTO.

IMPORTANT With the engine started,

any error between the lever position

and the gear actually engaged is

signalled by a buzzer until consistency

is restored.

push the gear lever towards (+) to

engage 1^stgear (if starting from N or R,

simply place the lever in the middle

position) or R to engage reverse;

release the brake pedal and press

the accelerator pedal: the gear most

suited to the vehicle speed will be

engaged.

GEAR LEVER

MANUAL MODE

The gear lever A fig. 83, located on the

dashboard, is floating multistable type,

i.e. it has three stable positions and

three unstable positions.

Proceed as follows:

press the brake pedal and start the

engine;

AUTO-ECO OPERATION

To activate the function, press the ECO

button fig. 84 on the central tunnel.

The ECO function can be only activated

only with automatic mode active.

if AUTO appears on the display,

move the lever A fig. 83 to A/M to

select MANUAL mode;

push gear lever A towards (+) to

engage first gear (if starting from N or

R, simply place the lever in the middle

position) or R to engage reverse;

release the brake pedal and press

the accelerator pedal;

F1D0107

83

in driving conditions, push lever A of

the gearbox towards (+) to engage

the next gear up or towards (–) to

engage the next gear down.

The three stable positions correspond

to neutral (N), reverse (R) and the

central position located between the

unstable positions (+) and (-).

F1D0108

84

94

With the ECO function active, the

system will select the most suitable

gear depending on the vehicle speed,

engine rpm and intensity with which the

accelerator pedal is pressed, with the

aim of limiting fuel consumption.

"AUTO" MODE

MODE SELECTOR

(Panda Cross 4x4 versions)

It is a driving mode aimed at comfort

and safety in normal grip and driving

conditions.

This device allows, using the ring of the

knob fig. 85 (on the central tunnel),

three car response modes to be

selected according to driving style and

road conditions:

"OFF ROAD" MODE

It is a driving mode aimed at setting off

in poor grip conditions on low-grip

road surfaces (e.g. snow, ice, mid, etc.).

“Kick Down” FUNCTION

(for versions/markets, where provided)

If necessary (e.g. when overtaking),

the system downshifts one or more

gears when the accelerator pedal

is depressed beyond the point where it

becomes stiff (and if the rpm allow it)

in order to provide suitable power and

torque for the acceleration requested

by the driver.

Activation

Rotate the ring fig. 85 to the right and

hold in this position for half a second,

until the corresponding LED lights

up and “Off Road” mode activation

indicator appears on the display with a

dedicated message.

Once released, the ring returns to the

central position.

F1D0116

IMPORTANT The use of the “Kick

Down” function is recommended only

when overtaking or accelerating quickly,

in order not to increase fuel

85

When the "Off Road" mode is activated,

the presetting for ELD system

intervention activates automatically.

1 = AUTO mode;

2 = OFF ROAD mode;

3 = Gravity Control function.

consumption.

The ring nut is monostable type. In

other words, it always remains in a

central position. The selected driving

mode is indicated by the corresponding

LED switching on the knob and by an

indication on the display.

WARNING

45) Avoid keeping your hand on this lever

except during gear change or AUTO/

MANUAL mode requests.

95

IMPORTANT When the "Off Road"

mode is activated, the Start&Stop

system is temporarily disabled.

IMPORTANT If “Off Road” or “Auto”

mode was active when the engine was

stopped, the next time it is started

the mode that was selected is

reactivated.

DUALDRIVE

ELECTRIC POWER

STEERING

Temporary deactivation of the system

switches on the corresponding LED on

the trim (located on the central

123) 124)

"GRAVITY CONTROL"

FUNCTION

This only operates with the key turned

to MAR and the engine started. The

steering allows the force required at the

steering wheel to be adjusted to suit

driving conditions.

dashboard). To activate the Start&Stop

function, with "Off Road" mode on,

press the button on the dashboard

trim. However, when the "Off Road"

mode is deactivated, the Start&Stop

system is enabled again.

This driving function permits a constant

vehicle speed to be maintained

downhill.

On/Off

IMPORTANT When turning the ignition

key quickly, full power steering

functionality can be achieved after a

few seconds.

For engaging/disengaging the Gravity

Control function refer to the "Active

safety systems" paragraph in the

"Safety" chapter.

IMPORTANT When the "Off Road"

mode is activated, the City Brake

Control system is temporarily

CITY FUNCTION

ACTIVATION/

DEACTIVATION

deactivated. Temporarily deactivation of

the system results in the switching on

FAILURE OF THE MODE

SELECTOR SYSTEM

of the

warning light on the

Press the CITY fig. 86 button to

activate/deactivate the function. The

activation of the function is signalled by

the word CITY on the display (in some

versions it is signalled by the word CITY

appearing on the instrument panel).

When the CITY function is on, the

steering wheel effort is lighter, making

parking easier: therefore, this function is

particularly useful for driving in city

centres.

instrument panel. When the "Off Road"

mode is deactivated, the City Brake

Control system is enabled again.

IMPORTANT In the event of system

failure or a fault with knob, no driving

modes can be selected. The display will

show a dedicated message.

Turning off

To deactivate the "Off Road" mode and

return to the "Auto" mode, rotate the

ring nut to the left and hold in this

position for half a second. In this case,

the LED corresponding to “Auto” mode

will light up and the “Off Road” mode

deactivation indication will appear

on the display.

IMPORTANT In this case it is not

advisable trying to drive down roads

with a steep gradient, the system

cannot help the driver in any way.

96

124) Before servicing the vehicle, switch off

the engine and remove the key from the

ignition switch to activate the steering lock.

This is especially important when the

vehicle wheels are not touching the

ground. If this is not possible (for example if

the key needs to be turned to MAR or the

engine must be running), remove the

main fuse that protects the electric power

steering.

ECO FUNCTION

(for versions/markets, where provided)

To activate the function press the ECO

button fig. 87.

F1D0025

86

IMPORTANT During parking

manoeuvres requiring a lot of steering,

the steering may become harder; this is

normal and is due to the intervention

of the system to protect the electric

steering motor from overheating so no

intervention is required. When the

vehicle is used again later on,

F1D0140

87

When the ECO function is active, the

vehicle is set for a driving style

characterised by reduced fuel

consumption. When the function is on,

the corresponding LED on the button

lights.

the power steering will work normally.

This function is stored, so when the

vehicle is started again, the system

keeps the setting it had before the

engine was stopped. Press the ECO

button again to deactivate the function

and restore the normal driving setting.

WARNING

123) It is absolutely forbidden to carry out

any after-market operation involving

steering system or steering column

modifications (e.g. installation of anti-theft

device) that could adversely affect

performance and safety, invalidate the

warranty and also result in non-compliance

of the vehicle with type-approval

requirements.

97

LED on: system deactivated.

START&STOP

SYSTEM

WARNING

46) If the climate comfort is to be favoured,

the Start&Stop system can be deactivated,

for a continuous operation of the climate

control system.

125)

126)

The Start&Stop system automatically

stops the engine when the vehicle

is stationary and starts it again when

the driver wants to move off. This

reduces consumption, the emission of

harmful gases and noise pollution.

F1D0040

88

OPERATING MODE

Engine stopping mode: with the

vehicle stopped, the engine stops with

gearbox in neutral and clutch pedal

released.

WARNING

125) If the battery needs to be replaced,

always contact a Fiat Dealership. Replace

the battery with one of the same type

(HEAVY DUTY) and with the same

specifications.

NOTE The engine can only be stopped

automatically after exceeding a speed

of about 10 km/h, to prevent the engine

from being repeatedly stopped when

driving at walking pace.

126) Before opening the bonnet, make

sure the engine is off and the ignition key is

in the STOP position. Please follow the

instructions on the decal near the front

crossmember. We recommend that you

remove the key from the ignition if other

people remain in the vehicle. Exit from the

vehicle only after having removed the

ignition key or having rotated it to

Restarting the engine: press the

clutch pedal to restart the engine.

MANUAL SYSTEM

ACTIVATION/

DEACTIVATION

the STOP position. During refuelling, make

sure that the engine is off and that the

ignition key is in the STOP position.

To activate/deactivate the system

manually, press the fig. 88 button on

the dashboard control panel.

LED off: system deactivated.

98

OPERATION WITH A

TRAILER

the presence of ultrasonic systems

(e.g. pneumatic brake systems of

trucks or pneumatic drills) near the

vehicle could alter the signals sent to

the sensor;

PARKING SENSORS

The operation of the sensors is

automatically deactivated when the

trailer electric cable plug is inserted in

the tow hook socket of the car. The

sensors are automatically reactivated

when the trailer's cable plug is

removed.

127)

47)

SENSORS

the variation in sensor position,

caused by variation in ride (due

to suspension or shock absorber wear),

changing tyres, overloaded car, or

tuning that lowers the car, for example,

may affect parking sensor system

performance;

The sensors are located in the rear

bumper fig. 89 and their function is to

detect the presence of any obstacles

near the rear part of the car and inform

the driver, through an intermittent

acoustic signal.

IMPORTANT NOTES

When parking, take the utmost care

over obstacles that may be above

or under the sensor.

the presence of a tow hook without

trailer interferes with the correct

operation of the parking sensors. If a

fixed tow hook is installed, the sensors

cannot be used. If the customer installs

a removable tow hook, this must

always be disconnected from

Objects close to the car are not

detected under certain circumstances

and could therefore cause damage

to the car or be damaged.

The following conditions may influence

the performance of the parking

assistance system:

the crossmember whenever the trailer

is not attached to prevent the activation

of the sensors.

the presence of ice, snow, mud or

multiple layers of paint on the surface of

the sensor may reduce its sensitivity

and the system performance;

F1D0045

89

WARNING

ACTIVATION/

DEACTIVATION

mechanical interference (e.g.

washing the car, rain, strong wind, hail)

may cause the sensor to detect a

non-existent obstacle ("echo

interference");

127) Parking manoeuvres, however, are

always the driver’s responsibility. While

carrying out these manoeuvres, always

make sure that no people (especially

children) or animals are in the area

concerned. The parking sensors are used

to assist the driver, who must never allow

his attention to lapse during potentially

dangerous manoeuvres, even those

executed at low speeds.

The sensors are automatically activated

when reverse gear is engaged. The

acoustic warning becomes more

frequent as the obstacle behind the car

gets closer.

99

DIESEL ENGINES

REFUELLING THE

VEHICLE

Operation at low temperatures

Only use Diesel for motor vehicles

(EN590 specification).

WARNING

47) For correct operation of the system,

sensors must always be clean from mud,

dirt, snow or ice. Be careful not to scratch

or damage the sensors while cleaning

them. Avoid using dry, rough or hard

cloths. The sensors must be washed using

clean water, with the addition of vehicle

shampoo if necessary. When using special

washing equipment such as high pressure

jets or steam cleaning, clean the sensors

very quickly keeping the jet more than

10 cm away.

When using or parking the car for a

long time in the mountains or cold

areas, it is advisable to refuel using

locally available diesel fuel. In this case,

it is also advisable to keep the tank

over 50% full.

128) 129) 130)

Always stop the engine before

refuelling.

PETROL ENGINES

Only use unleaded petrol, with an

octane number (R.O.N.) not lower than

95. In order to prevent damage to the

catalytic converter never introduce even

the smallest amount of leaded petrol,

even in the event of an emergency.

REFUELLING

PROCEDURE

48)

IMPORTANT If the filler compartment is

washed with a high-pressure jet, keep

it at a distance of at least 20 cm.

IMPORTANT An inefficient catalytic

converter leads to harmful exhaust

emissions, thus contributing to air

pollution.

Diesel and petrol versions

The refuelling procedure described

below is illustrated on the label B fig. 90

located inside the fuel flap. The label

also indicates the fuel type (UNLEADED

FUEL=petrol, DIESEL=diesel fuel).

To refuel proceed as follows:

IMPORTANT Never introduce leaded

petrol to the tank, even in small

amounts in an emergency, as this

would damage the catalytic converter

beyond repair.

open flap A fig. 90, pulling it

outwards;

introduce the dispenser in the filler

and refuel;

100

after refuelling, before removing the

dispenser, wait for at least 10 seconds

in order for the fuel to flow inside the

tank;

Emergency refuelling

Proceed as follows:

open the boot and take the adapter

B fig. 91 located in the tool box

then remove the dispenser from the

filler and close flap A.

(versions equipped with space-saver

wheel - for versions/markets, where

provided) or in the Fix&Go container

(versions equipped with Fix&Go);

F1D0114

92

switch off the engine;

apply the handbrake;

turn the ignition key to STOP;

do not smoke;

hand the special adapter A fig. 93

over to the qualified LPG refuelling

personnel.

F1D0048

91

IMPORTANT Depending on the country,

there are various types of adapters for

LPG refuelling pumps. Filler adapter,

supplied with the vehicle and located in

a special case, is specifically designed

for the country in which the vehicle is

sold. If you are in a different country,

find out what type of adaptor is used

there.

open flap A, pulling it outwards;

introduce the adapter B in the filler

and refuel;

after refuelling, remove the adapter

and close the flap, then reintroduce the

adapter in its casing and put it back

in the boot.

F1D0047

90

LPG versions

Flap A fig. 90 is provided with a dust

cover gaiter C which prevents deposits

of impurities and dust at the end of

the filler when the flap is closed.

To access the LPG filler, open the

access flap A fig. 92 and undo the cap

B.

Observe the following precautions

during the refuelling operation:

101

E5: Unleaded petrol containing up to

2.7% (m/m) oxygen and with maximum

5.0% (V/V) ethanol compliant with

EN228.

E10: Unleaded petrol containing up to

3.7% (m/m) oxygen and with maximum

10.0% (V/V) ethanol compliant with

EN228.

Symbols for diesel powered cars

F1D0110

94

Fuels - identification of

vehicle compatibility.

Graphic symbol for

consumer information in

accordance with

EN16942

The symbols shown below facilitated

recognising the correct fuel type to

be used on your car.

B7: Diesel containing up to 7% (V/V) of

FAME (Fatty Acid Methyl Esters)

compliant with EN590.

Before proceeding with refuelling,

check the symbols inside the fuel filler

flap (where provided) and compare

them with the symbols shown on the

fuel pump (where provided).

B10: Diesel containing up to 10% (V/V)

of FAME (Fatty Acid Methyl Esters)

compliant with EN16734.

F1D0115

93

Natural Power versions

49)

Symbols for petrol/LPG bi-fuel cars

To access filler B fig. 94, open the flap

and undo cap A turning it

anticlockwise.

Symbols for petrol powered cars

The profile of filler B for refilling is the

universal type, compatible with Italian

and NGV1 standards. In some

European countries adapters are

considered ILLEGAL (e.g. in Germany).

102

E5: Unleaded petrol containing up to

2.7% (m/m) oxygen and with maximum

5.0% (V/V) ethanol compliant with

EN228.

TOWING TRAILERS

WARNING

131) 132)

IMPORTANT

128) Do not apply any object/plug to the

end of the filler which is not provided for

the car. The use of non-compliant

objects/caps could cause a pressure

increase inside the tank, resulting in

dangerous situations.

E10: Unleaded petrol containing up to

3.7% (m/m) oxygen and with maximum

10.0% (V/V) ethanol compliant with

EN228.

For towing motorhomes or trailers the

vehicle must be fitted with an approved

tow hook and an adequate electrical

system. Installation must be carried out

by a specialist.

LPG: Automotive LPG compliant with

EN589.

129) Do not bring naked flames or lit

cigarettes near to the fuel filler: fire risk.

Keep your face away from the fuel filler to

prevent breathing in harmful vapours.

Install any specific and/or additional

door mirrors as specified by the

Highway Code.

Symbols for petrol/methane bi-fuel

cars

130) Do not use a mobile phone near the

refuelling pump: risk of fire.

Remember that when towing a trailer,

steep hills are harder to climb, braking

distances increase and overtaking

takes longer depending on the overall

weight of the trailer.

WARNING

Engage a low gear when driving

downhill, rather than constantly using

the brake.

48) For diesel engines, only use diesel fuel

for motor vehicles in accordance with

EN590 European specifications. The use of

other products or mixtures may damage

the engine beyond repair and

consequently invalidate the warranty, due

to the damage caused. If you accidentally

introduce other types of fuel into the tank,

do not start the engine. Empty the tank.

If the engine has been run for even an

extremely limited amount of time, you must

not only drain the fuel tank, but the rest of

the supply circuit as well.

E5: Unleaded petrol containing up to

2.7% (m/m) oxygen and with maximum

5.0% (V/V) ethanol compliant with

EN228.

The weight the trailer exerts on the

vehicle tow hook reduces the vehicle's

loading capacity by the same amount.

To make sure that the maximum

towable weight is not exceeded (given

in the vehicle registration document)

account should be taken of the fully

laden trailer, including accessories and

luggage.

E10: Unleaded petrol containing up to

3.7% (m/m) oxygen and with maximum

10.0% (V/V) ethanol compliant with

EN228.

CNG: Automotive compressed

methane compliant with EN16723.

49) The other plates (provided with the

vehicle documents) show the date when

the first cylinder inspection/test is due.

Methane refuelling stations are not

authorised to refill the cylinders when the

inspection date has expired.

103

Do not exceed the speed limits specific

to each country you are driving in, in

the case of vehicles towing trailers.

In any case, the top speed must not

exceed 100 km/h.

WARNING

131) The ABS with which the vehicle is

equipped will not control the braking

system of the trailer. Particular caution is

required on slippery roads.

An electric brake (or electric winch)

should be supplied directly by the

battery through a cable with a cross

section of no less than 2.5 mm².

In addition to the electrical branches,

the vehicle electrical system can only

be connected to the supply cable for an

electric brake and to the cable for an

internal light for the trailer, not

exceeding 15 W. For connections, use

the preset control unit with a battery

cable with section not less than 2.5

mm².

132) Never modify the braking system of

the vehicle to control the trailer brake.

The trailer braking system must be fully

independent of the vehicle’s hydraulic

system.

On Panda Cross and Panda 4x4

versions, in the event of prolonged

vehicle use at maximum tow capacity

on slopes, replacing engine oil more

frequently (every 10,000 km) is

advisable.

IMPORTANT The use of auxiliary loads

other than external lights (electric brake,

winch, etc.) must take place with

engine running.

IMPORTANT To install a tow hook

contact a Fiat Dealership.

104

IN AN EMERGENCY

A punctured tyre or a burnt-out bulb?

HAZARD WARNING LIGHTS...........106

REPLACING A BULB ......................106

REPLACING FUSES........................112

REPLACING A WHEEL ...................115

FIX&GO KIT.....................................118

JUMP STARTING............................121

At times, a problem may interfere

with our journey.

The pages on emergencies can help

you to deal with critical situations

independently and with calm.

In an emergency we recommend that

you call the freephone number found in

the Warranty Booklet.

FUEL CUT-OFF SYSTEM ................122

TOWING THE CAR .........................123

It is also possible to call the national or

international universal freephone

number to search for the nearest

Dealership.

105

NOTE When the weather is cold or

damp or after heavy rain or washing,

the surface of headlights or rear lights

may steam up and/or form drops of

condensation on the inside. This is

a natural phenomenon due to the

difference in temperature and humidity

between the inside and the outside

of the glass which does not indicate a

fault and does not compromise the

normal operation of lighting devices.

The mist disappears quickly when the

lights are turned on, starting from

the centre of the diffuser, extending

progressively towards the edges.

HAZARD WARNING

LIGHTS

REPLACING A BULB

Press button A fig. 95 to switch the

lights on/off. Warning lights and in

the instrument panel are lit up when

the lights are ON.

133) 134)

50) 51)

GENERAL

INSTRUCTIONS

Before replacing a bulb check the

contacts for oxidation;

IMPORTANT The use of hazard warning

lights is governed by the highway

code of the country you are driving in:

comply with legal requirements.

burnt bulbs must be replaced by

others of the same type and power;

after replacing a headlight bulb,

always check its alignment;

when a light is not working, check

that the corresponding fuse is intact

before replacing a bulb. For the location

of fuses, refer to the paragraph

"Replacing fuses" in this chapter.

F1D0023

95

Emergency braking

In the event of emergency braking the

hazard warning lights switch on

automatically as well as the

and

warning lights in the instrument

panel. The lights switch off

automatically when emergency braking

ceases.

106

Light bulbs

Type

H4

Power

55W

21W

5W

Dipped/main beam headlights

Front side lights/Day lights (DRL)

Rear side lights

P21/5W

PY21W

W5W

Front direction indicators

Side direction indicators

Rear direction indicators

Brake lights

21W

5W

PY21W

P21/5W

LED

21W

-

Third brake light

Fog lights

H11

55W

16W

5W

Reversing light

W16W

C5W

Rear fog light

Number plate

107

FRONT LIGHT CLUSTERS

(except Panda Cross versions)

The bulbs are arranged inside the front

light cluster fig. 96 as follows:

A - Dipped beam/main beam

headlights/direction indicators;

B - Daytime running lights (DRL);

C - Fog lights.

F1D0117

F1D0080

97

99

DIPPED/MAIN BEAMS

then refit the cover A.

To replace the bulb, proceed as follows:

remove cover A fig. 98;

DIRECTION INDICATORS

Front

To replace the bulb, proceed as follows:

remove cover B fig. 98;

turn the bulb holder anticlockwise,

extract the bulb and replace it;

F1D0134

96

refit the new bulb on the connector

making sure that it is locked correctly,

then reinsert the connector in its

housing rotating it clockwise;

FRONT LIGHT CLUSTERS

(Panda Cross versions)

On the Panda Cross versions, the bulbs

are arranged inside the front light

cluster fig. 97 as follows:

Side

F1D0079

98

A - Dipped beam/main beam

headlights/direction indicators;

B - Fog lights;

To replace the bulb, proceed as follows:

push the connector + bulb holder

unit B fig. 99 downwards;

adjust the lens A fig. 100 to

compress in the clip B, then pull the

cluster outwards;

C - Daytime Running Lights (DRL).

remove the bulb C from connector D

and replace it;

turn the bulb holder C anticlockwise,

extract the bulb and replace it;

refit the new bulb on the connector

making sure that it is locked correctly,

then reinsert the connector unit and the

bulb holder B in its housing;

refit the bulb holder C in the lens and

turn it clockwise;

108

refit the cluster making sure that the

internal catch B clips into position.

F1D0083

F1D0118

102

103

rotate and remove the bulb holder E,

release and replace the bulb;

F1D0081

100

refit the new lamp and carry out the

procedure described previously in

reverse.

FOG LIGHTS

(for versions/markets, where provided -

except Panda Cross versions)

To replace the bulb, proceed as follows:

FOG LIGHTS

(Panda Cross versions)

steer the wheel completely inwards,

adjust the screws A fig. 101 and

remove the flap B;

To change the fog light bulb, proceed

as follows:

F1D0119

104

steer both the wheels completely,

loosen the screws A fig. 103 and

remove the guard flap B;

reconnect the assembly to

connector B, reposition assembly C in

its housing by rotating it clockwise

by a quarter of a turn, until it clicks into

the correct position;

locate the fog light unit, rotate it

anticlockwise by a quarter of a turn and

remove it;

reposition the guard door B fig. 103,

taking care that the tabs are positioned

in their housings and tighten the fixing

screws A.

lift the lever A fig. 104 and

disconnect the connector B from the

bulb-bulb holder assembly C;

F1D0082

replace the bulb-bulb holder

assembly C;

101

release the clip C fig. 102 and

disconnect the electrical connector D;

109

SIDE LIGHTS / DAYTIME

RUNNING LIGHTS (DRL)

(for versions/markets, where provided -

except Panda Cross versions)

DAYTIME RUNNING

LIGHTS (DRL)

(Panda Cross versions)

IMPORTANT To change LED DRLs

contact a Fiat Dealership.

To replace the bulb, proceed as follows:

steer the wheel completely, adjust

the screws A fig. 101 and remove

the flap B;

REAR LIGHT CLUSTERS

These contain the bulbs for the side

lights, brake lights and direction

indicators.

release the clip C fig. 105 and

disconnect the electrical connector D;

To replace the bulb proceed as follows:

undo the two screws A fig. 106

from their seats, pull gently outwards

until releasing the whole headlight from

the two clips (press-fitted D fig. 107)

and release the connector;

F1D0085

106

F1D0084

105

refit the new lamp and carry out the

procedure described previously in

reverse.

rotate and remove the bulb holder E,

release and replace the bulb;

refit the new lamp and carry out the

procedure described previously in

reverse.

REVERSING LIGHT/REAR

FOG LIGHT

F1D0086

107

135)

undo the five screws B from their

seats and remove the bulb holder C;

The reversing lights and rear fog lights

are located in the rear bumper.

To replace the bulb, proceed as follows:

remove the bulbs, pushing them

slightly and turning them anti-

clockwise;

adjust the tabs A and remove the

flap B fig. 108

110

THIRD BRAKE LIGHTS

Insert the new bulb and make sure

that it is correctly clamped between the

contacts, then refit the lens A fig. 111.

These are located in the tailgate and

are LED lights. For replacement,

contact a Fiat Dealership.

WARNING

NUMBER PLATE LIGHTS

To replace the bulbs, proceed as

follows:

133) Modifications or repairs to the electric

system that are not carried out properly

or do not take the system technical

specifications into account can cause

malfunctions leading to the risk of fire.

remove lens A fig. 110;

F1D0087

108

release the clip C fig. 109 and

disconnect the electrical connector D;

134) Halogen bulbs contain pressurised

gas, in the case of breakage they may

burst causing glass fragments to be

projected outwards.

135) Before replacing the bulb, wait for the

catalytic converter to cool down: RISK

OF BURNS.

WARNING

F1D0089

110

replace the bulb A fig. 111, releasing

it from the side contacts;

50) Halogen bulbs must be handled

holding the metal part only. Touching the

transparent part of the bulb with your

fingers may reduce the intensity of the

emitted light and even reduce the lifespan

of the bulb. In the event of accidental

contact, wipe the bulb with a cloth

moistened with alcohol and let the bulb

dry.

F1D0088

109

turn the bulb holder E and remove it,

extract the bulb and replace it;

refit the new lamp and carry out the

procedure described previously in

reverse.

51) Where possible, it is advisable to have

bulbs changed at a Fiat Dealership. The

correct operation and direction of the

external lights are absolutely essential for

the safety of the car and of compliance

with the law.

F1D0090

111

STARTING AND DRIVING -> DUALDRIVE ELECTRIC POWER STEERING for Your Fiat Panda SUV Third Generation (2013-2023)

Related Topics

Popular Owner Manuals

Latest Owner Manuals