Get IN AN EMERGENCY -> REPLACING A BULB Guide for Fiat Punto SUV 2011-2018

HAZARD WARNING

LIGHTS

REPLACING A BULB

CONTROL

123) 124)

40)

Press button A (fig. 77) to turn on/off

the lights, whatever the position of the

ignition key. When the hazard warning

GENERAL

INSTRUCTIONS

before changing a bulb check the

contacts for oxidation;

lights are on, the

lights flash.

and warning

burnt bulbs must be replaced by

others of the same type and power;

after replacing a headlight bulb,

always check its alignment;

when a light is not working, check

that the corresponding fuse is intact

before replacing a bulb. For the location

of fuses, refer to the paragraph

"Replacing fuses" in this chapter.

F1E0932

77

Note A slight misting may appear on

the internal surface of the headlight: this

does not indicate a fault and is caused

by low temperature and the degree

of humidity in the air. Misting will rapidly

disappear when the headlights are

switched on. The presence of drops

inside the headlights indicates

Emergency braking

In the event of emergency braking the

hazard warning lights switch on

automatically as well as warning lights

and in the instrument panel.

The lights switch off automatically when

emergency braking ceases.

infiltration of water. Contact a Fiat

Dealership.

91

Bulbs

Type

H4

Power

55W/60W

21 W

5 W

Dipped/main beam headlights

Daytime running lights (DRL)

Front side lights

Rear side lights

W21W

W5W

LED

-

Front direction indicators

Side direction indicators

Rear direction indicators

Brake lights

PY21W

W5W

PY21W

P21W

W2.3W

H11

21 W

5 W

21 W

2.3 W

55 W

16 W

5 W

Third brake light

Fog lights

Reverse

W16W

C5W

Rear fog light

Number plate

92

FRONT LIGHT CLUSTERS

The bulbs are arranged inside the front

light cluster fig. 78 as follows:

A - Side lights

B - Daytime running lights (DRL)

C - Direction indicators

D - Dipped/main beam headlights

F1E0250

80

F1E0149

79

DIPPED/MAIN BEAM

HEADLIGHTS

remove bulb C fig. 79, replace it and fit

the bulb holder again; refit the rubber

cover making sure it is secured

correctly.

To replace the bulb, proceed as follows:

remove the rubber cover, disconnect

the electrical connector B fig. 81 and

detach the bulb holder clip;

Note To change the LED side lights

contact a Fiat Dealership.

extract the bulb A fig. 81 A and

replace it;

F1E0635

78

DAYTIME RUNNING

LIGHTS (DRL)

fit the new bulb, aligning the outlines

of the metallic part with the grooves

on the reflector. Refit the clip, reconnect

the electrical connector and refit the

cover making sure it is locked;

Note To replace the bulbs of the front

direction indicators, main beam

headlights and dipped beam

To replace a bulb, using the dedicated

tab, turn the bulb holder A fig. 80

anticlockwise and remove it. Extract the

bulb holder B fig. 80 pushing it lightly

and turning it anticlockwise, refit the

bulb holder fitting it into its housing and

turn it clockwise until it clicks into

place;

headlights, the dedicated flap can be

accessed (see "Direction indicators")

DIRECTION INDICATORS

Front

SIDE LIGHTS

(for versions/markets, where provided)

To replace the bulb, remove the rubber

cover with the dedicated tab and press

on tabs B fig. 79, then remove the

bulb holder;

To replace the bulb, proceed as follows:

steer the right/left wheel inwards

and unscrew the locking devices A fig.

82. Remove the flap B;

remove the bulb holder cover C fig.

83 by turning it anticlockwise;

93

extract the bulb D fig. 84 pushing it

lightly and turning it anticlockwise,

then replace it;

D

F1E0280

85

F1E0150

81

FOG LIGHTS

(for versions/markets, where provided)

A

F1E0153

84

To replace the bulbs proceed as

follows:

B

refit the cover/bulb holder C by

turning it clockwise until it is locked

properly. Fit the flap B and screw in the

locking devices A.

undo the screw A fig. 86 and

remove the protection template B;

loosen the fixing screws C fig. 86

and remove the lamp;

A

Side

F1E0621

82

To replace the bulb, proceed as follows:

A

C

adjust the lens A fig. 85 to

compress in the clip B, then pull the

cluster outwards;

turn the bulb holder C fig. 85

anticlockwise, extract bulb D and

replace it;

C

B

Refit the bulb holder C fig. 85 in the

lens turning it anticlockwise and refit the

unit making sure the inner clip B clicks

into place.

F1E0525

86

remove the bulb A fig. 87 by turning

it anticlockwise and disconnect the

electrical connector.

F1E0152

83

94

A

F1E0526

87

REAR LIGHT CLUSTERS

These contain the bulbs for the side

lights (LED), brake lights and direction

indicators. To replace the bulb proceed

as follows:

undo the screws A fig. 88 and

disconnect the electrical connector B,

then remove the lens unit pulling

outwards;

F1E0155

F1E0156

88

89

release the bulb holder unclipping

the fasteners C fig. 89;

REVERSING LIGHT/REAR

FOG LIGHT

THIRD BRAKE LIGHTS

remove the bulb to be replaced,

pushing it lightly and turning it

anticlockwise, then replace it;

To replace the bulb proceed as follows:

The reversing lights and rear fog lights

are located in the rear bumper. For their

replacement, contact a Fiat Dealership.

open the luggage compartment

and remove the rubber covers;

refit the bulb holder, reconnect the

electric connector, reposition the unit

on the vehicle body and then tighten

the fixing screws A fig. 88.

press on the locking devices and

remove the lens unit C fig. 90;

disconnect the electrical connector

and, working on the tabs D fig. 90

extract the bulb holder and then the

press-fitted bulb.

95

Download User Manual App

IN AN EMERGENCY -> REPLACING A BULB for Your Fiat Punto SUV 2011-2018

Related Topics

IN AN EMERGENCY

Popular Owner Manuals

Latest Owner Manuals