Get In the event of a breakdown -> Changing a bulb Guide for Fiat Scudo Van Third Generation (2022-2025)

In the event of a breakdown

Halogen bulbs (Hx)

To ensure good quality lighting, check

that the bulb is correctly positioned in its

housing.

Go promptly to a Fiat Dealership or a qualiﬁed

workshop.

Have the punctured tyre examined. After

inspection, the technician will advise you on

whether the tyre can be repaired or if it must

be replaced.

and rear lamps is normal, and will disappear

after the lamps have been on for a few

minutes.

The headlamps have polycarbonate

lenses with a protective coating:

– Do not clean them with a dry or abrasive

cloth, nor with detergent or solvent

products.

Opening the bonnet/Accessing the

bulbs

Proceed with caution when the engine is hot -

risk of burns!

Some driving aid functions should be

disabled, e.g. the Active Safety Brake.

– Use a sponge and soapy water or a pH

neutral product.

Take care with objects or clothing that could

be caught in the blades of the cooling fan -

risk of strangulation!

If your vehicle has tyre under-inﬂation

detection, check the tyre pressures and

reinitialise the system.

For more information on Tyre under-inﬂation

detection, refer to the corresponding section.

– When using a high-pressure washer on

persistent marks, do not keep the lance

directed towards the headlamps, lamps or

their edges for too long, so as not to damage

their protective coating and seals.

After changing a bulb

To reﬁt, carry out the operations in

reverse order to removal.

Close the protective cover very carefully to

guarantee the sealing of the lamps.

Tyre under-inﬂation detection

The steel spare wheel does not have a

sensor.

Changing a bulb must only be done with

the ignition oﬀ and after the headlamp /

lamp has been switched oﬀ for several

minutes - risk of serious burns!

Do not touch the bulb directly with your

ﬁngers; use a lint-free cloth.

It is essential only to use anti-ultraviolet

(UV) type bulbs, so as not to damage the

headlamp.

Model with halogen

headlamps

Wheel with wheel trim

When reﬁtting the wheel, reﬁt the wheel

trim, starting by aligning the cutout with the

valve and then pushing the trim into place all

round its edge with the palm of your hand.

Always replace a failed bulb with a new bulb

of the same type and speciﬁcation. To avoid

lighting imbalance, replace the bulbs in pairs.

Changing a bulb

In some weather conditions (e.g. low

temperature or humidity), misting on the

internal surface of the glass of the headlamps

1. Sidelamps (W5W-5W)

2. Main beam headlamps (H1-55W)

223

In the event of a breakdown

Dipped beam headlamps

Sidelamps

3. Dipped beam headlamps (H7-55W)

4. Daytime running lamps (W21W LL-21W)

5. Direction indicators (PY21W-21W amber)

Model with Xenon

headlamps

► Press the lower clip on the connector and

remove the assembly of connector and bulb.

► Pull out the bulb and replace it.

► Press the two side clips on the connector and

remove the assembly of connector and bulb.

► Pull out the bulb and replace it.

When reﬁtting the connector and bulb in

the lamp unit, correctly position the

assembly in its housing until it clicks into

place.

Main beam headlamps

1. Main beam headlamps (H1-55W)

2. Dipped beam headlamps (D8S-25W)

3. Direction indicators (PY21W-21W amber)

Do not touch the Xenon lamps (D8S)

– risk of electrocution!

If you need to replace this type of bulb, you

must contact a Fiat Dealership or a qualiﬁed

workshop.

► Press the lower clip on the connector and

remove the assembly of connector and bulb.

► Pull out the bulb and replace it.

Be aware of the zone behind the right

lamp (vehicle direction), which may be

hot with a risk of burning (degassing hoses).

Direction indicators

Daytime running lamps

Accessing the bulbs

► Turn the bulb holder a quarter turn

anti-clockwise.

► Press the two side clips on the connector and

remove the assembly of connector and bulb.

► Pull out the bulb and replace it.

► Press the upper clip on the cover then tilt it

backwards to remove it.

224

In the event of a breakdown

► Remove the bulb holder and replace the

faulty bulb.

Front foglamps (H11-55W)

Direction indicator side

repeater

Rapid ﬂashing of a direction indicator

lamp (left or right) indicates that one of

the bulbs on the corresponding side has

failed.

Amber-coloured bulbs must be replaced

by bulbs with identical speciﬁcations and

colour.

– Push the repeater towards the rear and

release it.

– When reﬁtting, engage the repeater towards

the front and then slide it backwards.

Amber coloured bulbs (direction indicators and

side repeaters) must be replaced with bulbs of

identical speciﬁcation and colour.

Daytime running lamps/

sidelamps

► Underneath the front bumper, slacken the

bolts on deﬂector A, then remove it.

Rear lamps

► Press the locking clip and disconnect the

connector.

► Unscrew the bulb holder a quarter turn anti-

clockwise and remove it.

► Replace the faulty bulb.

For the replacement of these bulbs, contact a

Fiat Dealership or a qualiﬁed workshop.

A replacement kit for the LEDs is available from

Fiat Dealerschips.

1. Brake lamps/Sidelamps (P21/5W-21/5W)

2. Direction indicators (PY21W-21W amber)

3. Reversing lamps (P21W-21W)

You can also contact a Fiat Dealership or

a qualiﬁed workshop to replace these

bulbs.

4. Foglamps/Sidelamps (P21/4W-21/4W)

225

In the event of a breakdown

For vehicles with interior trim, contact a

Fiat Dealership or a qualiﬁed workshop

to have the work done.

► While holding the lamp in place, press the

clip on the inside then carefully remove the lamp.

► Disconnect the electrical connector.

► Identify the defective lamp and then,

depending on the version, open the rear doors or

the tailgate.

► With side-hinged doors, remove the plastic

cover with the aid of a screwdriver.

► With a tailgate, unclip the trim at each end,

rotating it from bottom to top, then unclip the

centre clips to remove it.

► Using a screwdriver through the aperture,

push the lamp towards the outside.

► Disconnect the electrical connector and then

remove the lamp.

► Unscrew the bulb holder a quarter turn anti-

clockwise and replace the faulty bulb.

To reﬁt, press on the lamp to clip it into place.

► Spread the 3 lugs slightly, then extract the

bulb holder.

► Remove the faulty bulb by pressing lightly on

it, then turning it a quarter turn clockwise.

► Replace the bulb.

► With side-hinged doors, unscrew the 2 ﬁxing

screws from the outside.

► With the tailgate, unclip the plastic trim from

the outside and then tilt it outwards to remove it.

Then unscrew the 2 ﬁxing screws.

Third brake lamp (W5W - 5W)

► Depending on version, open the rear left-

hand door or tailgate.

► From the inside, and depending on the

version, remove the ventilation grille.

226

Download User Manual App

In the event of a breakdown -> Changing a bulb for Your Fiat Scudo Van Third Generation (2022-2025)

Related Topics

In the event of a breakdown

Popular Owner Manuals

Latest Owner Manuals