Get In the event of a breakdown -> Spare wheel Guide for Fiat Scudo Van Third Generation (2022-2025)

In the event of a breakdown

► Turn the pipe assembly 2 to the left until it

comes into contact with the unit.

Do not forget to obtain a new cartridge,

available from a Fiat Dealership or a qualiﬁed

workshop.

3. Wheel bolt cover/wheel trim removal tool.

Depending on the vehicle's equipment, this is

used to remove the wheel bolt covers on alloy

wheels or the wheel trim on steel wheels.

4. Socket for "anti-theft" wheel bolts.

Used to adapt the wheelbrace to the special

"anti-theft" bolts.

8

► Disconnect the connector 1 from the cartridge

by turning it a quarter turn anti-clockwise.

► Pull the pipe assembly 2 out slightly, then

disconnect the connector 3 from the air intake

pipe by turning it a quarter turn anti-clockwise.

Spare wheel

5. Towing eye.

Access to the tools

The tools are stowed in a tool box.

For more information on Towing, please

For more information on the Tool box,

refer to the corresponding section.

These tools are speciﬁc to the vehicle

and may vary according to the level of

equipment.

List of tools

Do not use them for any other purpose.

The jack must only be used to change a

wheel with a damaged or punctured tyre.

Do not use any jack other than the one

supplied with the vehicle.

If the vehicle does not have its original jack,

contact a Fiat Dealership or a qualiﬁed

workshop to obtain the one that was intended

by the manufacturer.

► Remove the pipe assembly 2.

► Hold the compressor up vertically.

► Unscrew the cartridge 4 from the bottom.

To ﬁt the new cartridge and new pipe, carry out

these operations in reverse order.

Beware of ﬂuid discharge.

The expiry date of the ﬂuid is indicated

on the cartridge.

The sealant cartridge is designed for single

use; it must be replaced even if only partly

used.

The jack meets European standards, as

deﬁned in the Machinery Directive 2006/42/

CE.

1. Wheelbrace.

Used to remove the wheel bolts and raise/

lower the jack.

2. Jack.

The jack does not require any maintenance.

After use, do not discard the cartridge in

standard waste, take it to a Fiat Dealership or

an authorised waste disposal site.

Used to raise the vehicle.

219

In the event of a breakdown

Remove the spare wheel from the

carrier

Reﬁt the spare wheel in the carrier

Accessing the spare wheel

► Access to the spare wheel is from the rear.

► Depending on version, open the side-hinged

doors or the tailgate.

To avoid any unwanted opening of the

electric side door(s), deactivate the

Hands-Free Tailgate Access function in the

vehicle conﬁguration menu.

For more information on the Hands-free

sliding side door, refer to the corresponding

section.

► Access the carrier bolt, located on the rear

door sill.

► Slacken the bolt using the wheelbrace (about

14 turns) until the carrier is low enough to allow

the carrier hook to be disengaged.

► Position the wheel facing the carrier.

► Progressively return the wheel to the carrier

by pushing alternately at the left and right until it

is clear of the hook ﬁxing area.

► Engage the carrier on the hook, then tighten

the bolt using the wheelbrace until the bolt is fully

tightened.

► If the vehicle is ﬁtted with a towbar, raise

the rear of the vehicle using the jack (must be

at jacking point B) to allow suﬃcient space to

remove the spare wheel.

Tyre in the carrier

You can change the size of the tyre on the spare

wheel by following the instructions below.

► Release the carrier from the hook, take the

spare wheel and place it next to the wheel to be

changed.

220

In the event of a breakdown

Apply the parking brake, unless it is

programmed to automatic mode (for an

electric parking brake), and check that the

indicator lamp lights up on the instrument

panel.

Ensure that the occupants have left the

vehicle and are located in a safe place.

Never go underneath a vehicle raised using a

jack; use an axle stand.

Original tyre

XS-M

XL

8

size

215/65 R16

215/60 R17

Placing a

225 wheel in

the carrier is

prohibited.

There is no

restriction.

215/60 R17

M&S

► Place the foot of the jack on the ground and

ensure that it is directly below the A or B jacking

point provided on the underbody, whichever is

closest to the wheel to be changed.

225/55 R17 Placing a 215

wheel in the

With an electric parking brake, place a chock

against the wheel diagonally opposite to the

one being replaced.

carrier is not

recommended

(risk of noise).

A punctured tyre of size 215 or 225 can

be placed in the carrier.

Removing a wheel

Parking the vehicle

Immobilise the vehicle where it does

not obstruct traﬃc: the ground must be level,

stable and non-slippery.

With a manual gearbox, engage ﬁrst gear

then switch oﬀ the ignition to block the

wheels.

With an automatic gearbox, place the gear

selector in position P then switch oﬀ the

ignition to block the wheels.

With a drive selector, place the gear selector

in position P then switch oﬀ the ignition to

block the wheels.

► With a steel wheel, remove the bolt cover

using tool 3 or the wheel trim by hand.

► With an alloy wheel, remove the cover from

each of the bolts using tool 3.

► If the vehicle is so equipped, ﬁt security bolt

socket 4 to wheelbrace 1 to slacken the security

bolt.

► Slacken (without removing) the other wheel

bolts using just wheelbrace 1.

221

In the event of a breakdown

► Use the knob to extend the jack 2 until its

head comes into contact with jacking point A or

B, whichever is used; contact surface A or B on

the vehicle must be correctly engaged with the

central part of the head of the jack.

► Remove the wheel.

► Lower the vehicle again fully.

► Fold jack 2 and remove it.

Fitting the wheel

► Raise the vehicle until there is suﬃcient

space between the wheel and the ground, to

then easily ﬁt the spare (not punctured) wheel.

Risk of injury!

Ensure that the jack is stable. If the

ground is slippery or loose, the jack may slip

or collapse.

► If ﬁtted to your vehicle, tighten the anti-theft

bolt using the wheelbrace 1 ﬁtted with the anti-

theft socket 4.

Ensure that the jack is positioned strictly at

one of the jacking points A or B under the

vehicle, making sure that the vehicle's contact

surface is correctly centred on the head of the

jack. Otherwise, there is a risk of damage to

the vehicle and/or of the jack collapsing.

► Tighten the other bolts using the

wheelbrace 1 only.

► Stow the tools in the tool box.

► Fit the wheel on the hub.

► Screw in the bolts by hand as far as possible.

► If ﬁtted to your vehicle, pre-tighten the anti-

theft bolt using the wheelbrace 1 ﬁtted with the

anti-theft socket 4.

Fitting a steel or "space-saver" type

spare wheel

► Pre-tighten the other bolts using the

wheelbrace 1 only.

If the vehicle is ﬁtted with alloy wheels, the

washers A do not make contact with the steel

or "space-saver" type spare wheel. The wheel

is held in place by the conical contact surface

B of each bolt.

After changing a wheel

► Remove the bolts and store them in a clean

Stow the punctured wheel in the carrier.

place.

222

Download User Manual App

In the event of a breakdown -> Spare wheel for Your Fiat Scudo Van Third Generation (2022-2025)

Related Topics

In the event of a breakdown

Popular Owner Manuals

Latest Owner Manuals