2015-2026 Fiat Tipo 4 Door KNOWING THE INSTRUMENT PANEL -> WARNING LIGHTS AND MESSAGES User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

KNOWING THE INSTRUMENT PANEL -> WARNING LIGHTS AND MESSAGES for Your Fiat Tipo 4 Door Second Generation (2015-2026)

WARNING LIGHTS AND MESSAGES  
WARNING The warning light switches on in the instrument panel together with a dedicated message and/or acoustic signal  
when applicable. These indications are indicative and precautionary and as such must not be considered as exhaustive and/or  
alternative to the information contained in the Owner Handbook, which you are advised to read carefully in all cases. Always  
refer to the information in this section in the event of a failure indication.  
WARNING Failure indications displayed are divided into two categories: very serious and less serious failures. Serious faults are  
indicated by a repeated and prolonged warning "cycle". Less serious faults are indicated by a warning "cycle" with a shorter  
duration. The display cycle of both categories can be interrupted. The instrument panel warning light will stay on until the cause  
of the failure is eliminated.  
NOTE The warning lights and symbols described below are indicative and can change based on the version or market.  
Red warning lights  
Warning light  
What it means  
INSUFFICIENT BRAKE FLUID / PARKING BRAKE ON  
The warning light switches on when the ignition device is brought to MAR, but it should switch off after a few  
seconds.  
Low brake fluid level  
The warning light turns on when the level of the brake fluid in the reservoir falls below the minimum level, possibly  
due to a leak in the circuit. Restore the brake fluid level, then check that the warning light has switched off. If the  
warning light stays on, contact a Fiat Dealership.  
red  
Parking brake on  
The warning light switches on when the parking brake is engaged.  
POWER STEERING FAILURE  
The warning light switches on when the ignition device is brought to MAR, but it should switch off after a few  
seconds. If the warning light remains on, you could not have power steering and the effort required to operate  
the steering wheel could be increased; steering the car is still possible. Contact a Fiat Dealership as soon as  
possible.  
red  
58  
Warning light  
What it means  
EBD FAILURE  
The simultaneous switching on of the  
a failure of the EBD system or that the system is not available. In this case, the rear wheels may suddenly lock  
and the vehicle may swerve when braking sharply.  
Drive very carefully to the nearest Fiat Dealership to have the system inspected immediately.  
(red) and  
(amber) warning lights with the engine on indicates either  
red  
amber  
SEAT BELTS REMINDER  
The warning light switches on constantly if the vehicle is stationary and the driver side or passenger side seat  
belt (for versions/markets, where provided), with the passenger seated, is not fastened. The warning light flashes  
and an acoustic warning will sound if the car is in motion and the driver side or passenger side seat belt (for  
versions/markets, where provided), with the passenger seated, is not correctly fastened. In this case, fasten the  
seat belt.  
red  
ENGINE COOLANT TEMPERATURE TOO HIGH  
The warning light on the display lights up when the engine has overheated.  
In normal driving conditions: stop the car, switch off the engine and check that the coolant level in the  
reservoir is not below the MIN mark. In this case, wait for the engine to cool down, then slowly and carefully  
open the cap, top up with coolant and check that the level is between the MIN and MAX marks on the reservoir  
itself. Also check visually for any fluid leaks. If, when restarting, the warning light on the display switches on  
again, contact a Fiat Dealership.  
If the vehicle is used under demanding conditions (e.g. in high-performance driving): slow down and, if  
the warning light stays on, stop the vehicle. Stop for two or three minutes with the engine running and slightly  
accelerated to facilitate better coolant circulation, then turn the engine off. Check that the coolant level is correct  
as described above.  
red  
IMPORTANT Over demanding routes, it is advisable to keep the engine running and slightly accelerated for a few  
minutes before turning it off.  
AIRBAG FAILURE  
If the warning light switches on constantly, this indicates a failure in the airbag system.  
38) 39)  
red  
59  
Warning light  
What it means  
HANDS NOT DETECTED ON STEERING WHEEL  
(for versions/markets, where provided)  
The light comes on if the driver’s hands are not detected on the steering wheel.  
red  
Amber warning lights  
Warning light  
What it means  
iTPMS  
(For versions/markets where provided)  
iTPMS failure/iTPMS temporarily deactivated  
The warning light flashes for about 75 seconds and then stays on constantly to indicate that the system is  
temporarily deactivated or faulty. The system will go back to normal operation when the operating conditions will  
allow it. If this is not the case, carry out the Reset procedure after restoring the normal operating conditions.  
If the malfunction warning persists, contact a Fiat Dealership as soon as possible.  
Low tyre pressure  
The warning light switches on constantly to indicate that the pressure of one or more tyres is lower than the  
recommended value and/or that slow pressure loss is occurring. In these cases, optimal tyre duration and fuel  
consumption may not be guaranteed. It is advisable to restore the correct pressure value (see the "Wheels"  
paragraph in the "Technical Specifications" section).  
amber  
Once the normal operating conditions of the car are restored, carry out the "Reset" procedure.  
IMPORTANT Do not continue driving with one or more flat tyres as the car handling may be compromised. Stop  
the car, avoiding sharp braking and steering.  
ABS FAILURE  
The warning light switches on to indicate an ABS fault. In this case the braking system maintains its efficiency  
unaltered but without the advantage of the ABS system. Drive carefully and contact a Fiat Dealership as soon as  
possible.  
amber  
amber  
ESC SYSTEM (where provided)  
ESC system activation  
Intervention by the system is indicated by the flashing of the warning light: it indicates that the car is in critical  
stability and grip conditions.  
60  
Warning light  
What it means  
ESC/Traction Plus system failure (where provided)  
If the warning light does not switch off, or if it stays on with the engine running, a failure was found on the ESC  
system/Traction Plus system. Contact a Fiat Dealership as soon as possible.  
Hill Hold Control system failure  
The warning light turns on to indicate a Hill Holder Control system failure. Contact a Fiat Dealership as soon as  
possible.  
amber  
PARTIAL DEACTIVATION OF ACTIVE SAFETY SYSTEMS  
The warning light switches on to indicate that some active safety systems have been partially deactivated. When  
the systems are reactivated, the warning light switches off.  
amber  
amber  
REAR FOG LIGHT  
The warning light switches on when the rear fog light is turned on.  
INJECTION / EOBD SYSTEM FAILURE  
In normal conditions, when the ignition device is brought to MAR, the warning light switches on, but it should  
switch off as soon as the engine is started. The operation of the warning light may be checked by the traffic  
police using specific devices. Comply with the laws and regulations of the country where you are driving.  
13)  
Injection system failure  
If the warning light remains on, or it switches on whilst driving, the injection system is not working properly. The  
warning light on constantly signals a malfunction in the supply/ignition system which could cause high exhaust  
emissions, a possible loss of performance, poor driveability and high consumption. The warning light switches off  
if the malfunction disappears, but is still stored by the system. Under these conditions, you can continue travelling  
at moderate speed but without demanding excessive effort from the engine or high speed. Prolonged use of the  
car with the warning light on fixed may cause damage. Contact a Fiat Dealership as soon as possible.  
Catalytic converter damage  
amber  
If the warning light flashes, it means that the catalytic converter may be damaged.  
Release the accelerator pedal to lower the speed of the engine until the warning light stops flashing. Continue the  
journey at moderate speed, trying to avoid driving conditions that may cause further flashing and contact a Fiat  
Dealership as soon as possible.  
61  
Warning light  
What it means  
UREA INJECTION SYSTEM FAILURE (Diesel versions)  
(for versions/markets, where provided)  
The warning light switches on if a fluid not conforming with the nominal characteristics is added or if an average  
UREA consumption of more than 50% is detected.  
Contact a Fiat Dealership as soon as possible.  
If the problem is not solved, a dedicated message will appear on the instrument panel display whenever a certain  
threshold is reached until it will no longer be possible to start the engine.  
When 200 km will remain to prevent the engine restart, a continuous dedicated message will appear on the  
dashboard (for versions/markets, where provided) accompanied by an acoustic warning sound.  
amber  
GLOW PLUG PREHEATING (Diesel versions)  
This warning light or symbol comes on when moving the ignition device to MAR and will switch off when the glow  
plugs have reached the preset temperature. The engine can be started as soon as the warning light switches off.  
WARNING In mild or high temperature conditions, the warning light comes on for a very short time only.  
GLOW PLUG PREHEATING FAILURE (Diesel versions)  
amber  
The warning light will flash to indicate a failure in the glow plug preheating system. In this case, contact a Fiat  
Dealership as soon as possible.  
FUEL RESERVE / LIMITED RANGE  
This warning light on the display comes on when about 5 to 7 litres of fuel are left in the tank.  
14)  
amber  
amber  
amber  
AUTONOMOUS EMERGENCY BRAKING CONTROL SYSTEM (AEB Control)  
(for versions/markets, where provided)  
The warning light or the symbol turns on when the Autonomous Emergency Braking Control (AEB Control)  
system is deactivated by the driver or in the event of automatic deactivation following a temporary system failure.  
Contact a Fiat Dealership as soon as possible.  
START&STOP SYSTEM MANUAL ACTIVATION / DEACTIVATION  
(for versions/markets, where provided)  
The warning light or symbol also appears on the display if the Start&Stop system is deactivated.  
62  
Warning light  
What it means  
LANE CONTROL SYSTEM (where provided)  
The warning light turns on fixed yellow when the car approaches the lane line. The warning light flashes when the  
car crosses the lane line. Refer to “Lane Control" in “Starting and driving” for more information.  
amber  
Green warning lights  
Warning light  
What it means  
“DUALDRIVE” ELECTRIC POWER STEERING SYSTEM ACTIVATION  
(For versions/markets where provided)  
The indication CITY switches on when the "Dualdrive" electric power steering system is activated by pressing the  
relative control button. If the button is pressed again the word CITY goes out.  
green  
green  
green  
SIDE LIGHTS AND DIPPED BEAM HEADLIGHTS  
The warning light switches on when the side/tail lights or dipped headlights are turned on.  
This function allows the headlights to remain on for 30, 60 or 90 seconds after the ignition device was placed in  
STOP position ("Follow me home" function).  
FOG LIGHTS  
The warning light comes on when the front fog lights are turned on.  
AUTOMATIC MAIN BEAM HEADLIGHTS  
This warning light comes on when the automatic main beam headlights are activated.  
green  
green  
LEFT DIRECTION INDICATOR  
The warning light switches on when the direction indicator stalk is moved downwards or, together with the right  
direction indicator, when the hazard warning light button is pressed.  
63  
Warning light  
What it means  
RIGHT DIRECTION INDICATOR  
The warning light switches on when the direction indicator stalk is moved upwards or, together with the left  
direction indicator, when the hazard warning light button is pressed.  
green  
green  
LANE CONTROL SYSTEM (where provided)  
The Lane Control warning light is on steady in green when one or both lane limits have been detected and the  
system is active and ready to provide visual warnings and a torque warning if the lane is left involuntarily.  
Refer to the “Lane Control System” chapter in the “Starting and driving” section for further information.  
TRACTION PLUS SYSTEM ACTIVATION  
(for versions/markets, where provided)  
This warning light or symbol also appears on the display in the event of a Traction Plus system activation.  
green  
Blue warning lights  
Warning light  
What it means  
MAIN BEAM HEADLIGHTS  
The warning light switches on when the main beam headlights are turned on.  
blue  
White warning lights  
Warning light  
What it means  
LANE CONTROL FAILURE  
The warning light switches on in the case of failure of the Lane Control device. Contact a Fiat Dealership as soon  
as possible to have the failure eliminated.  
white  
64  
SYMBOLS AND MESSAGES ON THE DISPLAY  
ꢀ
Symbol  
What it means  
AIRBAG FAILURE  
The symbol switches on if there is an airbag system failure. Contact a Fiat Dealership as soon as possible.  
red  
red  
LOW ENGINE OIL PRESSURE  
The symbol switches on in the case of insufficient engine oil pressure.  
15)  
WARNING Do not use the car until the failure has been solved. The switching on of the symbol does not show  
the quantity of oil in the engine: the oil level must be checked manually.  
ALTERNATOR FAILURE  
The switching on of the symbol with engine on corresponds to an alternator failure. Contact a Fiat Dealership as  
soon as possible.  
red  
DOORS OPEN  
The symbol switches on when one or more doors are not completely shut. An acoustic warning is activated with  
the doors open and the car moving. Close the doors properly.  
red  
red  
BONNET NOT PROPERLY SHUT  
The symbol switches on when the engine bonnet is not properly shut (for versions/markets, where provided).  
Close the bonnet properly.  
TAILGATE NOT PROPERLY SHUT  
The symbol switches on when the tailgate is not properly shut (for versions/markets, where provided). Close the  
tailgate correctly.  
red  
65  
Symbol  
What it means  
DUAL CLUTCH AUTOMATIC TRANSMISSION FAILURE  
The symbol switches on, together with an acoustic warning, to indicate the failure of the dual clutch automatic  
transmission. Contact a Fiat Dealership as soon as possible.  
red  
DAA SYSTEM (Drive Attention Assist) INTERVENTION  
The symbol comes on in the event of a DAA (Driver Attention Assist) system intervention. The system, after  
estimating the driver’s drowsiness level, through specific events, suggests to the driver to stop for a break,  
because continuing driving is risky. Stop to pause while driving, pulling the car over in safe conditions.  
16)  
red  
HANDS NOT DETECTED ON STEERING WHEEL  
(for versions/markets, where provided)  
The symbol appears if the driver’s hands are not detected on the steering wheel.  
red  
DAA SYSTEM (Drive Attention Assist) FAILURE  
The symbol comes on in the event of a DAA (Driver Attention Assist) system failure. Contact a Fiat Dealership.  
yellow amber  
KEYLESS ENTRY/GO SYSTEM FAILURE  
The symbol comes on in the event of a Keyless Entry/Go system failure. Contact a Fiat Dealership as soon as  
possible.  
yellow amber  
yellow amber  
ENGINE OIL PRESSURE SENSOR FAILURE  
The symbol switches on in the event of engine oil level sensor failure.  
DUAL CLUTCH AUTOMATIC TRANSMISSION OVERTEMPERATURE  
The symbol switches on in the case of transmission overheating, after a particularly demanding use. In this case  
an engine performance limitation is carried out. With engine off or at idle speed, wait until the symbol switches  
off.  
yellow amber  
yellow amber  
RAIN SENSOR FAILURE  
The symbol switches on in the case of failure of the rain sensor. Contact a Fiat Dealership as soon as possible.  
66  
Symbol  
What it means  
FUEL CUT-OFF SYSTEM OPERATION  
The symbol switches on in the event of fuel cut-off system intervention.  
For reactivating the fuel cut-off system, refer to the description in the "Fuel cut-off system" section in the "In an  
emergency" chapter. If it is still not possible to restore the fuel supply, contact a Fiat Dealership.  
yellow amber  
yellow amber  
FUEL CUT-OFF SYSTEM FAILURE  
The symbol switches on in the event of fuel cut-off system failure. Contact a Fiat Dealership as soon as possible.  
START&STOP SYSTEM FAILURE  
(for versions/markets, where provided)  
The symbol switches on to report a failure of the Start&Stop system. Contact a Fiat Dealership as soon as  
possible.  
yellow amber  
yellow amber  
EXTERNAL LIGHTS FAILURE  
The symbol switches on to indicate a failure on the following lights: daytime running lights (D.R.L.); parking lights;  
side lights; direction indicators; rear fog light; reversing light; number plate lights.  
The anomaly may be caused by a blown bulb, a blown protection fuse or an interruption of the electrical  
connection.  
FUEL LEVEL SENSOR FAILURE  
The symbol switches on in the event of fuel level sensor failure. Contact a Fiat Dealership.  
yellow amber  
yellow amber  
WATER IN DIESEL FILTER (Diesel versions)  
The warning light or the symbol switches on fixed while driving to indicate the presence of water in the diesel  
filter.  
14)  
POSSIBLE ICE ON ROAD  
The symbol turns on when the external temperature falls to or below 3°C.  
WARNING In the event of external temperature sensor failure, the digits that indicate the value are replaced by  
dashes.  
yellow amber  
67  
Symbol  
What it means  
FIAT CODE SYSTEM FAILURE  
The symbol switches on to indicate a failure of the Fiat CODE system. Contact a Fiat Dealership as soon as  
possible.  
yellow amber  
yellow amber  
DUSK SENSOR FAILURE  
The symbol switches on in the case of failure of the dusk sensor. Contact a Fiat Dealership as soon as possible.  
SOUND SYSTEM FAILURE  
The symbol switches on to report a failure of the sound system. Contact a Fiat Dealership as soon as possible.  
yellow amber  
yellow amber  
PARK ASSIST SYSTEM FAILURE  
The yellow symbol switches on in the case of temporary failure of the Park Assist system. If the problem is still  
present after cleaning the parking sensor area, contact a Fiat Dealership.  
The red symbol comes on in the case of permanent Park Assist system failure. The failed operation of the system  
might be due to the insufficient voltage from the traditional battery or other failures on the electrical system.  
Contact a Fiat Dealership as soon as possible.  
AUTONOMOUS EMERGENCY BRAKING CONTROL (AEB Control) SYSTEM FAILURE  
The yellow symbol switches on in the case of the temporary failure of the Autonomous Braking Control (AEB  
Control) system. Contact a Fiat Dealership as soon as possible.  
The red symbol switches on in the case of permanent failure of the Autonomous Braking Control (AEB Control)  
system. Contact a Fiat Dealership as soon as possible.  
yellow amber  
yellow amber  
BLIND SPOT ASSIST SYSTEM FAILURE  
The symbol comes on in the event of a Blind Spot Assist system failure. Contact a Fiat Dealership as soon as  
possible.  
68  
Symbol  
What it means  
SPEED LIMITER FAILURE  
The symbol switches on in the case of failure of the Speed Limiter device. Contact a Fiat Dealership as soon as  
possible to have the failure eliminated.  
yellow amber  
TRAFFIC SIGN RECOGNITION SYSTEM FAILURE  
The symbol comes on in the event of a Traffic Sign Recognition system failure. Contact a Fiat Dealership as soon  
as possible.  
TRAFFIC SIGN RECOGNITION SENSOR BLINDED  
In the event of a temporary condition that inhibits the use of the camera (such as grazing sun, rain, fog, snow or  
dirt) the symbol will light up temporarily until conditions are restored and the system can be used again.  
yellow amber  
TRAFFIC SIGN RECOGNITION SYSTEM DEACTIVATED  
The symbol comes on if the Traffic Sign Recognition system is off.  
yellow amber  
yellow amber  
LANE CONTROL SYSTEM  
The symbol will be solid yellow when the car is approaching a lane marker. The symbol will flash when the car  
is crossing the lane marker. Refer to “Lane Control" in “Starting and driving” for more information.  
LANE CONTROL SYSTEM FAILURE  
The symbol comes on in the event of a Lane Control system failure. Contact a Fiat Dealership as soon as  
possible.  
LANE CONTROL SYSTEM SENSOR BLINDED  
In the event of a temporary condition that inhibits the use of the camera (such as grazing sun, rain, fog, snow or  
dirt) the symbol will light up temporarily until conditions are restored and the system can be used again.  
yellow amber  
LANE CONTROL SYSTEM DEACTIVATED  
The symbol switches on if the Lane Control system is deactivated.  
yellow amber  
69  
Symbol  
What it means  
SCHEDULED SERVICING (SERVICE)  
The “Service Schedule” includes car maintenance at fixed intervals (refer to the "Maintenance and care" chapter).  
When the next scheduled service is approaching, the symbol will be displayed, followed by the number of  
kilometres/miles or days (where provided) left, when the ignition device is turned to MAR.  
This is displayed automatically, with ignition device at MAR, 2000 km before servicing or, where provided, 30  
days before servicing. It is also displayed each time the ignition device is turned to MAR.  
The display will be in km or miles according to the unit of measurement set. Go to a Fiat Dealership, where the  
"Scheduled Servicing Plan" work will be performed and the message will be reset.  
yellow amber  
yellow amber  
CLUTCH PEDAL  
This symbol lights up to indicate that the clutch pedal must be pressed to enable starting for versions with  
manual gearbox.  
DPF CLEANING (particulate trap) in progress (diesel versions with DPF only)  
The symbol switches on constantly to indicate that the DPF system needs to eliminate the trapped pollutants  
(particulate) through the regeneration process. The symbol stays off during the entire DPF regeneration  
and lights up only when driving conditions require the driver to be notified.  
The symbol does not switch on during every DPF regeneration, but only when driving conditions require that  
the driver is notified. To turn off the symbol, keep the car in motion until the regeneration process is over. The  
process normally takes about 15 minutes. Optimal conditions for completing the process are achieved by  
travelling at 60 km/h with engine speed above 2000 rpm.  
When this symbol switches on, it does not indicate a defect of the car and thus it should not be taken to a  
workshop.  
yellow amber  
WARNING Failure to follow the required procedure when the DPF warning light comes on for a  
mileage equal to or greater than 30 km or for a cumulative time equal to or greater than 2 hours, may  
result in the warning light coming on with consequent damage to the DPF device. Remember that  
if the warning light is on, it is necessary to go to the Dealership to restore the DPF to correct  
operation.  
70  
Symbol  
What it means  
GPF CLEANING (particulate filter) in progress (petrol versions only with GPF) (where provided)  
The symbol switches on constantly to indicate that the GPF system needs to eliminate the trapped pollutants  
(particulate) through the regeneration process.  
The symbol does not light up on during every GPF regeneration, but only when driving conditions require that the  
driver is notified.  
To turn off the symbol, keep the car in motion until the regeneration process is over. The optimal conditions for  
completing the process are achieved by varying the speed of the car (press and release the accelerator pedal).  
Maintain a speed above 60 km/h, on an extra-urban route, with an engine speed above 2000 rpm until the  
symbol turns off.  
yellow amber  
When this symbol switches on, it does not indicate a fault and thus it should not be taken to a workshop.  
GPF FAILURE (particulate filter) (petrol versions only with GPF) (where provided)  
The symbol lights up fixed together with the warning light and dedicated messages appear on the display in case  
of failure to the GPF (Gasoline Particulate Filter).  
In this case, contact a Fiat Dealership as soon as possible.  
INDICATION OF DIESEL EMISSIONS ADDITIVE LOW LEVEL (UREA)  
(for versions/markets, where provided)  
The Diesel Emissions Additive (UREA) low level symbol lights when the UREA level is low.  
Top up the UREA tank as soon as possible with at least 5 litres of UREA. If topping up is done with remaining  
range of UREA in the tank equal to zero, you may need to wait 2 minutes before starting the engine.  
yellow amber  
yellow amber  
AUTOMATIC HIGH BEAM HEADLIGHTS FAILURE  
The symbol switches on to report a failure of the automatic main beam headlights. Contact a Fiat Dealership as  
soon as possible.  
71  
Symbol  
What it means  
DEGRADED ENGINE OIL (where provided)  
Diesel versions: the symbol is shown on the display. The symbol is displayed for 3 minute cycles and intervals  
of 5 seconds until oil is changed. The symbol is displayed until the problem is solved.  
Petrol versions: the symbol switches on and then is not displayed when the display cycle is completed.  
WARNING After the first indication, each time the engine is started the symbol will continue to switch on as  
described above until the oil is changed.  
If the symbol flashes, this does not mean that there is a fault on the car, rather it simply reports that it is now  
necessary to change the oil as a result of regular use of the car. The deterioration of engine oil is accelerated  
by using the car for short drives, preventing the engine from reaching operating temperature. Contact a Fiat  
Dealership as soon as possible.  
yellow amber  
17) 18)  
START&STOP SYSTEM ACTIVATION  
(for versions/markets, where provided)  
The symbol switches on to report the activation of the Start&Stop system.  
green  
green  
“DUALDRIVE” ELECTRIC POWER STEERING SYSTEM ACTIVATION  
The indication CITY switches on when the "Dualdrive" electric power steering system is activated by pressing the  
relative control button. If the button is pressed again the word CITY goes out.  
INTELLIGENT SPEED ASSIST SYSTEM ACTIVATION (where provided)  
The symbol comes on in the event of a Intelligent Speed Assist system failure.  
green  
green  
ELECTRONIC CRUISE CONTROL  
The symbol comes on in the event of a Cruise Control system failure.  
SPEED LIMITER  
The symbol comes on in the event of a Speed Limiter system failure.  
green  
72  
Symbol  
What it means  
LANE CONTROL SYSTEM  
The Lane Control symbol comes on continuously green when one or both lane markings have been detected and  
the system is active and ready to provide visual and torque warnings if an unintentional lane departure occurs.  
Refer to the “Lane Control System” chapter in the “Starting and driving” section for further information.  
green  
LANE CONTROL SYSTEM  
When the Lane Control system is active but not enabled, the symbol comes on continuously white. This occurs  
when only left, right, or neither lane line has been detected. If a single lane line is detected, the system is ready to  
provide only visual warnings if an unintentional lane departure occurs on the detected lane line.  
Refer to the “Lane Control System” chapter in the “Starting and driving” section for further information.  
white  
BEAM HEIGHT  
The symbol indicates the height of the dipped beam headlamps, set to four levels (0-4) using buttons  
and  
.
white  
GEAR SHIFT ADVICE  
This symbol appears to suggest engaging a higher gear (upshifting).  
white  
white  
GEAR SHIFT ADVICE  
The symbol appears to suggest engaging a lower gear (downshifting).  
SPEED LIMIT EXCEEDED  
The (white) symbol switches on when the speed limit (e.g. 110 km/h) set through the menu of the display is  
exceeded (the inner value updates according to the set speed).  
white  
white  
START&STOP SYSTEM ACTIVATION  
(for versions/markets, where provided)  
The symbol comes on to indicate that the engine has been stopped by the Start&Stop system.  
73  
Symbol  
What it means  
ELECTRONIC CRUISE CONTROL  
The symbol appears when the electronic Cruise Control is turned on.  
white  
NOTE Some warning lights come on cyclically for a few seconds to run a safety check (for versions/markets, where provided) when the engine  
is started. Contact a dealership in the event of faults (warning lights stay on, etc.). The warning lights will go out if there are no faults.  
74  
Messages on display  
What it means  
What to do  
INDICATION OF DIESEL EMISSIONS ADDITIVE LOW  
LEVEL (UREA)  
(for versions/markets, where provided)  
When low UREA level is detected, a text message will  
appear on the instrument panel display, together with  
the symbol  
up.  
The symbol  
to indicate that UREA must be topped  
stays on until the tank is topped up  
®
with at least 5 litres of UREA.  
Top up the AdBlue (UREA) tank as soon as possible  
with at least 5 litres. If topping up is done with  
remaining range of AdBlue® (UREA) in the tank equal to  
zero, you may need to wait 2 minutes before starting  
the engine.  
If you do not top up, a specific message will appear  
on the instrument panel display whenever a certain  
threshold is reached until it will no longer be possible  
to start the engine.  
A message appears continuously on the display  
when the residual range is approximately 200 km  
accompanied by an auditory indication.  
19)  
When the residual range is 0 km, a specific message  
will appear on the display (for versions/markets, where  
provided). It will no longer be possible to restart the  
engine after it has been stopped.  
It will be possible to restart the engine after pouring at  
least 5 litres of UREA in the tank.  
BLIND SPOT ASSIST SYSTEM  
(where provided)  
Sensor block  
BLIND SPOT ASSIST  
A message will appear on the display if the Blind  
Spot Assist system sensor is blocked. In this case,  
the LEDs on the door mirrors are switched on  
continuously.  
Free the bumper of any obstacles or clean it.  
75  
What it means  
System not available  
A message will appear on the display if the Blind  
Spot Assist system sensor is not available. In this  
case, the LEDs on the door mirrors are switched on  
continuously.  
What to do  
The failed operation of the system might be due to  
the insufficient voltage from the traditional battery or  
other failures on the electrical system. Contact a Fiat  
Dealership as soon as possible to have the electrical  
system checked.  
BLIND SPOT ASSIST  
Blind Spot Assist system failure  
A message will appear on the display if the Blind Spot  
Assist system sensor is faulty. In this case, the LEDs  
on the door mirrors are switched off. An acoustic  
warning is also emitted.  
Contact a Fiat Dealership as soon as possible to have  
the failure eliminated.  
LANE CONTROL SYSTEM  
Camera obstructed  
A dedicated message is shown on the display in the  
case of dirt on the windscreen, which may adversely  
affect correct operation of the camera.  
Clean the windscreen using a soft clean cloth, taking  
care not to scratch it. Should the failure persist, contact  
a Fiat Dealership as soon as possible.  
LANE CONTROL  
System not available  
A dedicated message is shown on the display if the  
Lane Control system is not available.  
Contact a Fiat Dealership as soon as possible.  
SISTEMA AUTONOMOUS EMERGENCY BRAKING  
CONTROL  
The “BRAKE!” message appears on the display when  
the Autonomous Emergency Braking Control (AEB  
Control) system is activated.  
Increase your distance from the vehicle ahead to  
prevent the risk of collisions.  
AUTONOMOUS  
EMERGENCY BRAKING  
CONTROL  
A dedicated message is shown on the display if the  
Autonomous Emergency Braking Control system is not  
available.  
Camera obstructed  
Clean the windscreen using a soft clean cloth, taking  
care not to scratch it. Should the failure persist, contact  
a Fiat Dealership as soon as possible.  
A dedicated message is shown on the display in the  
case of dirt on the windscreen, which may adversely  
affect correct operation of the camera.  
76  
What it means  
System not available  
A dedicated message is shown on the display if the  
Autonomous Emergency Braking Control system is not  
available.  
What to do  
AUTONOMOUS  
EMERGENCY BRAKING  
CONTROL  
Contact a Fiat Dealership as soon as possible.  
SCHEDULED SERVICING (SERVICE)  
When the next scheduled service deadline is  
approaching, the word "Service" will be displayed,  
followed by the number of kilometres/miles or days  
(where provided) left, when the ignition device is  
turned to MAR.  
This is displayed automatically, with ignition device at  
MAR, 2000 km before servicing or, where provided,  
30 days before servicing. It is also displayed each time  
the ignition device is turned to MAR. The display  
will be in km or miles depending on the unit of  
measurement set.  
“SERVICE” MESSAGE  
(SCHEDULED  
SERVICING)  
Go to a Fiat Dealership, where the "Scheduled Servicing  
Plan" work will be performed and the message will be  
reset.  
DISPLAY FAILURE  
All warning lights flashing All the warning lights flash in the event of an  
instrument panel display failure.  
Contact a Fiat Dealership as soon as possible.  
Contact a Fiat Dealership as soon as possible.  
CONTROL SYSTEM WARNING LIGHT FAILURE  
Message to have the  
warning light checked  
The failure of the control system warning light is  
indicated by a message on the instrument panel  
display.  
IMPORTANT  
38) If, when the ignition device is turned to MAR, the warning light  
does not switch on or stays on while driving, a failure may have  
occurred in the restraint systems. In this case the airbags or pretensioners may not be deployed in an impact or, in a lower number of cases,  
they may be deployed accidentally. Before continuing, contact a Fiat Dealership immediately to have the system checked.  
77  
39) The failure of the  
warning light is signalled by the lighting up of the symbol  
on the instrument panel display (or, for versions where  
provided, by the flashing of the generic failure warning light). In this case, the warning light may not indicate any faults with the restraint  
systems. Before continuing, contact a Fiat Dealership immediately to have the system checked.  
WARNING  
13) If, turning the ignition device to MAR, the warning light  
Dealership as soon as possible.  
14) The presence of water in the fuel system circuit may cause severe damage to the injection system and irregular engine operation. If the  
does not turn on or if it turns on steadily or flashing while driving, contact a Fiat  
symbol is displayed contact a Fiat Dealership as soon as possible to bleed the system. If the above indications come on immediately after  
refuelling, water has probably been poured into the tank: switch the engine off immediately and contact a Fiat Dealership.  
15) If the  
symbol switches on while driving, stop the engine immediately and contact a Fiat Dealership.  
16) Driving the vehicle with this symbol on may severely damage the transmission, with resulting breakage. The oil may also overheat: contact  
with hot engine or with exhaust components at high temperature could cause fires.  
17) Degraded engine oil should be replaced as soon as possible after the warning light  
comes on, and never more than 500 km after it first  
comes on. Failure to observe the above may result in severe damage to the engine and invalidate the warranty. Remember that when this  
warning light comes on, it does not mean that the level of engine oil is low, so if it flashes it does not mean that you need to top  
up the engine oil.  
18) If the warning light flashes when driving, contact a Fiat Dealership.  
®
®
19) When the AdBlue (UREA) tank is empty and the engine is stopped it is no longer possible to restart it until the AdBlue (UREA) tank is  
topped up with at least 5 litres.  
78  

Related Topics

KNOWING THE INSTRUMENT PANEL
INSTRUMENT PANEL FEATURES DISPLAY EOBD SYSTEM (European On Board Diagnosis)

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot