Get Locks and Security Guide for Ford Edge SUV First Generation (2007-2014)

KEYS

Your vehicle is equipped with two

integrated keyhead transmitters

(IKTs). The IKT functions as both a

programmed ignition key that

operates all the locks and starts the

vehicle, and the transmitter portion

functions as the remote entry

transmitter.

Your IKTs are programmed to your vehicle; using a non-programmed key

will not permit your vehicle to start. If you lose your authorized dealer

supplied IKTs, replacement IKTs are available through your authorized

dealer. Standard SecuriLock威 keys without remote entry transmitter

functionality can also be purchased from your authorized dealer if

desired.

Always carry a spare key with you in case of an emergency.

For more information regarding programming replacement IKTs, refer to

the SecuriLock威 passive anti-theft system section later in this chapter.

Note: Your vehicle’s IKTs were

issued with a security label that

provides important vehicle key cut

information. It is recommended that

you keep the label in a safe place

for future reference.

Locks and Security

103

2010 Edge (edg)

Owners Guide, 3rd Printing

USA (fus)

POWER DOOR LOCKS

• Press the control to unlock all

doors.

• Press the

control to lock all

doors.

Smart locks

This feature helps to prevent you from locking yourself out of the vehicle

if your key is still in the ignition.

When you open one of the front doors or the liftgate and you lock the

vehicle with the power door lock control (on the driver or passenger

door trim panel), all the doors will lock, then all doors will automatically

unlock reminding you that your key is still in the ignition.

The vehicle can still be locked, with the key in the ignition, by locking

the driver’s door with a key, using the lock control on the remote entry

transmitter portion of your Integrated Keyhead Transmitter, or locking

the vehicle with the keyless entry keypad (if equipped).

If both front doors and the liftgate are closed, the vehicle can be locked

from any method, regardless of whether the key is in the ignition or not.

Autolock feature

The autolock feature will lock all the doors when:

• all the doors are closed,

• the ignition is in the on position,

• you shift into any gear putting the vehicle in motion, and

• the vehicle attains a speed greater than 12 mph (20 km/h).

The autolock feature repeats when:

• any door is opened then closed while the ignition is in the on position

and the vehicle speed is 9 mph (15 km/h) or lower, and

• the vehicle then attains a speed greater than 12 mph (20 km/h).

Locks and Security

104

2010 Edge (edg)

Owners Guide, 3rd Printing

USA (fus)

Deactivating/activating autolock feature

Your vehicle comes with the autolock features activated; there are four

methods to enable/disable this feature:

• Through your authorized dealer,

• by using a power door unlock/lock procedure,

• using a keypad procedure (if equipped), or

• or by using the instrument cluster message center (if equipped). Refer

to Message center in the Instrument Cluster chapter.

Note: The autolock feature can be activated/deactivated independently

of the autounlock feature.

Power door lock switch autolock enable/disable procedure

Before starting, ensure the ignition is in the off position and all vehicle

doors are closed. You must complete Steps 1–5 within 30 seconds or the

procedure will have to be repeated. If the procedure needs to be

repeated, wait a minimum of 30 seconds before beginning again.

1. Place the key in the ignition and

turn the ignition to the on position.

2. Press the power door unlock

control on the door panel three

times.

3. Turn the ignition from the on

position to the off position.

4. Press the power door unlock

control on the door panel three

times.

5. Turn the ignition back to the on position. The horn will chirp one time

to confirm programming mode has been entered and is active.

6. To enable/disable the autolock feature, press the unlock control, then

press the lock control. The horn will chirp once if autolock was

deactivated or twice (one short and one long chirp) if autolock was

activated.

7. Turn the ignition to the off position. The horn will chirp once to

confirm the procedure is complete.

Locks and Security

105

2010 Edge (edg)

Owners Guide, 3rd Printing

USA (fus)

Keyless entry keypad autolock enable/disable procedure

1. Turn the ignition to the off

position.

2. Close all the doors.

3. Enter factory–set 5–digit entry

code.

4. Press and hold the 3 • 4. While holding the 3 • 4pressthe7• 8.

5. Release the 7 • 8.

6. Release the 3 • 4.

The user should receive a horn chirp to indicate the system has been

disabled or a chirp followed by a honk to indicate the system has been

enabled.

Autounlock feature

The autounlock feature will unlock all the doors when:

• the ignition is in the on position, all the doors are closed, and the

vehicle has been in motion at a speed greater than 12 mph (20 km/h);

• the vehicle has then come to a stop and the ignition is turned to the

off or accessory position; and

• the driver door is opened within 10 minutes of the ignition being

transitioned to the off or accessory position.

Note: The doors will not autounlock if the vehicle has been

electronically locked before the driver door is opened.

Deactivating/activating autounlock feature

Your vehicle comes with the autounlock features activated; there are four

methods to enable/disable this feature:

• Through your authorized dealer,

• by using a power door unlock/lock sequence,

• using a keypad procedure (if equipped), or

• or by using the instrument cluster message center (if equipped). Refer

to Message center in the Instrument Cluster chapter.

Note: The autounlock feature can be activated/deactivated

independently of the autolock feature.

Locks and Security

106

2010 Edge (edg)

Owners Guide, 3rd Printing

USA (fus)

Power door lock switch autounlock enable/disable procedure

Before starting, ensure the ignition is in the off position and all vehicle

doors are closed. You must complete Steps 1–5 within 30 seconds or the

procedure will have to be repeated. If the procedure needs to be

repeated, wait a minimum of 30 seconds before beginning again.

1. Place the key in the ignition and

turn the ignition to the on position.

2. Press the power door unlock

control on the door panel three

times.

3. Turn the ignition from the on

position to the off position.

4. Press the power door unlock

control on the door panel three

times.

5. Turn the ignition back to the on position. The horn will chirp one time

to confirm programming mode has been entered and is active.

6. To enable/disable the autounlock feature, press the lock control, then

press the unlock control. The horn will chirp once if autounlock was

deactivated or twice (one short and one long chirp) if autounlock was

activated.

7. Turn the ignition to the off position. The horn will chirp once to

confirm the procedure is complete.

Keyless entry keypad autounlock enable/disable procedure

1. Turn the ignition to the off

position.

2. Close all the doors.

3. Enter factory–set 5–digit entry

code.

4. Press and hold the 3 • 4. While holding the 3 • 4, press and release

the 7 • 8. While still holding the 3 • 4, press and release the 7 • 8a

second time.

5. Release the 3 • 4.

The user should receive a horn chirp to indicate the system has been

disabled or a chirp followed by a honk to indicate the system has been

enabled.

Locks and Security

107

2010 Edge (edg)

Owners Guide, 3rd Printing

USA (fus)

CHILDPROOF DOOR LOCKS

• When these locks are set, the

rear doors cannot be opened from

the inside.

• The rear doors can be opened

from the outside when the

childproof door locks are set, but

the doors are unlocked.

The childproof locks are located on

the rear edge of each rear door and

must be set separately for each

door. Setting the lock for one door

will not automatically set the lock

for both doors.

• Insert the key and turn to the

lock position (key horizontal) to

engage the childproof locks.

• Insert the key and turn to the

unlock position (key vertical) to

disengage the childproof locks.

REMOTE ENTRY SYSTEM

The Integrated Keyhead Transmitter (IKT) complies with part 15 of the

FCC rules and with RSS-210 of Industry Canada. Operation is subject to

the following two conditions: (1) This device may not cause harmful

interference, and (2) This device must accept any interference received,

including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to

operate the equipment.

Locks and Security

108

2010 Edge (edg)

Owners Guide, 3rd Printing

USA (fus)

There are two possible types of IKTs:

• Vehicles equipped with a power

liftgate

• Vehicles not equipped with a

power liftgate

The typical operating range for your IKT is approximately 33 feet

(10 meters). A decrease in operating range could be caused by:

• weather conditions,

• nearby radio towers,

• structures around the vehicle, or

• other vehicles parked next to your vehicle.

Locks and Security

109

2010 Edge (edg)

Owners Guide, 3rd Printing

USA (fus)

The IKT allows you to:

• remotely unlock the vehicle doors.

• remotely lock all the vehicle doors.

• remotely open the power liftgate (if equipped).

• activate the personal alarm.

• operate the illuminated entry feature.

The remote entry lock/unlock feature operates in any ignition position

except while the key is held in the start position. The panic feature

operates with the key in the off position.

If there are problems with the remote entry system, make sure to take

ALL Integrated Keyhead Transmitters with you to the authorized

dealer in order to aid in troubleshooting the problem.

Unlocking the doors/two stage unlock

1. Press and release to unlock the driver’s door. Note: The interior

lamps and parking lamps will illuminate.

2. Press

and release again within three seconds to unlock all the

doors.

The remote entry system activates the illuminated entry feature; this

feature turns on the lamps for 25 seconds or until the ignition is turned

to the on position.

The battery saver feature will turn off the lamps 10 minutes after the

ignition is turned to the off position.

Two stage unlocking may be disabled or re-enabled by simultaneously

pressing the

and controls on the IKT for four seconds (disabling

two stage unlock allows all vehicle doors to unlock simultaneously). The

parking lamps will flash twice to indicate that two-stage unlock was

enabled or disabled.

Locking the doors

1. Press and release to lock all the doors. The parking lamps will

illuminate.

2. Press

and release again within three seconds to confirm that all

the doors are closed. Note: The doors will lock again, the horn will chirp

and the turn lamps will illuminate if all the doors and liftgate are closed.

Note: If any door or the liftgate is not closed, the horn will chirp twice

and the lamps will not flash.

Locks and Security

110

2010 Edge (edg)

Owners Guide, 3rd Printing

USA (fus)

Opening the power liftgate (if equipped)

Press twice within three seconds to fully unlatch and open the

liftgate.

WARNING: Make sure all persons are clear of the liftgate area

before using power liftgate control.

In order to fully lower and latch the liftgate, press the control twice.

If the liftgate stops mid travel, it may have detected an obstacle, Check

to ensure the liftgate swing zone is free from obstruction and reset the

power assist by manually closing the liftgate. Normal operation can then

be resumed.

WARNING: Make sure the liftgate is closed to prevent exhaust

fumes from being drawn into the vehicle. This will also prevent

passengers and cargo from falling out. If you must drive with the

liftgate open, keep the vents open so outside air comes into the

vehicle.

Car finder

Press

twice within three seconds. The horn will chirp and the turn

lamps will flash. It is recommended that this method be used to locate

your vehicle, rather than using the panic alarm.

Sounding a panic alarm

Press

to activate the alarm. The horn will sound and the turn lamps

will flash for a maximum of three minutes. Press again or turn the

ignition to the on position to deactivate, or wait for the alarm to time out

in three minutes.

Note: The panic alarm will only operate when the ignition is in the off

position.

Memory feature (seat and mirrors)

The integrated keyhead transmitter (IKT) allows you to recall the

memory seat and power mirrors feature.

Locks and Security

111

2010 Edge (edg)

Owners Guide, 3rd Printing

USA (fus)

Press to automatically move the driver seat, power mirrors and

adjustable pedals to the desired memory position. The mirrors will move

to the programmed position and the seat will move to the easy entry

position. The seat will move to the final position when the key is in the

ignition (if easy entry feature is enabled).

Programming the memory feature to the transmitter

To activate this feature:

1. Move the driver seat and power mirrors to the desired positions using

the associated controls.

2. Press and hold control button 1

for five seconds. A tone will be

heard after two seconds confirming

memory position has been set.

Continue to hold until a second tone

is heard after five seconds.

3. Within three seconds press

the

4. A tone will be heard when the

transmitter programming is

complete.

5. Press the

6. Repeat this procedure for memory 2 and another transmitter if

desired.

Deprogramming the memory feature from the transmitter

To deactivate this feature:

1. Press and hold either the 1 or 2 control on the driver’s door for five

seconds. A tone will be heard after 1

⁄

seconds when the memory store

is done, continue to hold until a second tone is heard after five seconds.

2. Within three seconds press the

3. A tone will be heard when the deactivation is complete.

4. Repeat this procedure for another transmitter if desired.

Replacing the battery

The integrated keyhead transmitter uses one coin type three-volt lithium

battery CR2032 or equivalent.

Locks and Security

112

2010 Edge (edg)

Owners Guide, 3rd Printing

USA (fus)

To replace the battery:

1. Twist a thin coin in the slot of the

IKT near the key ring in order to

remove the battery cover.

Note: Do not wipe off any grease on

the battery terminals on the back

surface of the circuit board.

2. Remove the old battery.

Note: Please refer to local

regulations when disposing of

transmitter batteries.

3. Insert the new battery. Refer to

the instructions inside the IKT for

the correct orientation of the

battery. Press the battery down to

ensure that the battery is fully

seated in the battery housing cavity.

4. Snap the battery cover back onto

the key.

Note: Replacement of the battery will not cause the IKT to become

deprogrammed from your vehicle. The IKT should operate normally after

battery replacement.

Replacing lost integrated keyhead transmitters (IKTs)

If you would like to have your integrated keyhead transmitters

reprogrammed because you lost one, or would like to buy additional

IKTs, you can either reprogram them yourself, or take all IKTs to your

authorized dealer for reprogramming.

How to reprogram your integrated keyhead transmitters (IKTs)

To program a new integrated keyhead transmitter yourself, refer to

Programming spare keys in the SecuriLock威 passive anti-theft system

section of this chapter. Note: At least two IKTs are required to perform

this procedure yourself.

Illuminated entry

The interior lamps, parking lamps and puddle lamps (if equipped)

illuminate when the Integrated Keyhead Transmitter or the keyless entry

system keypad is used to unlock the door(s).

Locks and Security

113

2010 Edge (edg)

Owners Guide, 3rd Printing

USA (fus)

The illuminated entry system will turn off the lights if:

• the ignition is turned to the on position, or

• the Integrated Keyhead Transmitter lock control is pressed, or

• the vehicle is locked using the keyless entry keypad (if equipped), or

• after 25 seconds of illumination.

The lights will not turn off if:

• they have been turned on with the dimmer control, or

• any door is open.

Illuminated exit

• When all vehicle doors are closed and the key is removed from the

ignition, the interior dome lamps, parking lamps and the puddle lamps

(if equipped) will illuminate.

The lamps will turn off if all the doors remain closed and

• 25 seconds elapse, or

• the key is inserted in the ignition.

Battery saver

The battery saver will shut off the lamps 10 minutes after the ignition

has been turned to the off position.

• If the dome lamps were turned on using the panel dimmer control, the

battery saver will shut them off 10 minutes after the ignition has been

turned to the off position.

• If the courtesy lamps were turned on because one of the vehicle doors

or the liftgate was opened, the battery saver will shut them off

10 minutes after the ignition has been turned to the off position.

• The battery saver will shut off the headlamps 10 minutes after the

ignition has been turned to the off position.

SECURICODE™ KEYLESS ENTRY SYSTEM (IF EQUIPPED)

You can use the keyless entry

keypad to:

• lock or unlock the doors without

using a key.

• recall memory seat/power mirrors

positions (if equipped).

Locks and Security

114

2010 Edge (edg)

Owners Guide, 3rd Printing

USA (fus)

The keypad can be operated with the factory set 5–digit entry code; this

code is located on the owner’s wallet card in the glove box and is

available from your authorized dealer. You can also create up to three of

your own 5–digit personal entry codes.

When pressing the controls on the keypad, press the middle of the

controls to ensure a good activation.

Programming a personal entry code and keypad association to

memory feature

To create your own personal entry code:

1. Enter the factory set code.

2. Within five seconds press the 1 • 2 on the keypad.

3. Enter your personal 5-digit code. Each number must be entered

within five seconds of each other.

4. For memory recall feature, enter the sixth digit 1 • 2 to store driver 1

settings or 3 • 4 to store driver 2 settings.

Note: Pressing 5 • 6, 7 • 8, or 9 • 0 keypad numbers as a sixth digit

will not recall a driver memory setting.

Note: The factory-set code cannot be associated with a memory setting.

5. The doors will lock then unlock to confirm that your personal entry

code has been programmed to the module.

Tips:

• Do not set a code that uses five of the same number.

• Do not use five numbers in sequential order.

• The factory set code will work even if you have set your own personal

code.

Erasing personal code

1. Enter the factory set 5–digit code.

2. Within five seconds, press the 1 • 2 on the keypad and release.

3. Press and hold the 1 • 2 for two seconds. This must be done within

five seconds of completing Step 2.

All personal codes are now erased and only the factory set 5–digit code

will work.

Anti-scan feature

If the wrong code has been entered seven times (35 consecutive button

presses), the keypad will go into an anti-scan mode. This mode disables

the keypad for one minute and the keypad lamp will flash.

Locks and Security

115

2010 Edge (edg)

Owners Guide, 3rd Printing

USA (fus)

The anti-scan feature will turn off after:

• one minute of keypad inactivity.

• pressing the

control on the remote entry transmitter portion of

your Integrated Keyhead Transmitter.

• the ignition is turned on.

Unlocking and locking the doors using keyless entry

To unlock the driver’s door, enter the factory set 5-digit code or your

personal code. Each number must be pressed within five seconds of each

other. The interior lamps will illuminate. Note: If the two-stage unlocking

feature is disabled, all doors will unlock; for more information regarding

two-stage unlocking, refer to the Unlocking the doors/Two stage unlock

section earlier in this chapter.

To unlock all doors, enter the factory set code or your personal code,

then press the 3 • 4 control within five seconds.

To lock all doors, press and hold the 7 • 8 and the 9 • 0 at the same

time (with the driver’s door closed). You do not need to enter the

keypad code first.

SECURILOCK姞 PASSIVE ANTI-THEFT SYSTEM

SecuriLock威 passive anti-theft system is an engine immobilization

system. This system is designed to help prevent the engine from being

started unless a coded integrated keyhead transmitter (IKT)

programmed to your vehicle is used. The use of the wrong type of

coded key may lead to a “no-start” condition.

Your vehicle comes with two coded integrated keyhead transmitters;

additional coded IKTs may be purchased from your authorized dealer.

Standard SecuriLock威 keys without remote entry transmitter

functionality can also be purchased from your authorized dealer if

desired. The authorized dealer can program your spare IKTs to your

vehicle or you can program the IKTs yourself. Refer to Programming

spare keys for instructions on how to program the coded key.

Note: The SecuriLock威 passive anti-theft system is not compatible with

non-Ford aftermarket remote start systems. Use of these systems may

result in vehicle starting problems and a loss of security protection.

Note: Large metallic objects, electronic devices that are used to

purchase gasoline or similar items, or a second coded key on the same

key chain may cause vehicle starting issues. You need to prevent these

objects from touching the coded IKT while starting the engine. These

Locks and Security

116

2010 Edge (edg)

Owners Guide, 3rd Printing

USA (fus)

objects will not cause damage to the coded IKT, but may cause a

momentary issue if they are too close to the IKT when starting the

engine. If a problem occurs, turn the ignition off, remove all objects on

the key chain away from the coded IKT and restart the engine.

Note: Do not leave a duplicate coded key in the vehicle. Always

take your keys and lock all doors when leaving the vehicle.

Anti-theft indicator

The anti-theft indicator is located in the instrument panel cluster.

• When the ignition is in the off

position, the indicator will flash

once every two seconds to

indicate the SecuriLock威 system

is functioning as a theft

deterrent.

• When the ignition is in the on position, the indicator will glow for

three seconds to indicate normal system functionality.

If a problem occurs with the SecuriLock威 system, the indicator will flash

rapidly or glow steadily when the ignition is in the on position. If this

occurs, turn the ignition off then back to on to make sure there was no

electronic interference with the programmed key. If the vehicle doesn’t

start, try to start it with the 2nd programmed key and if successful

contact your authorized dealership for key replacement. If the indicator

still flashes rapidly or glows steadily, the vehicle will not start, contact

your authorized dealer as soon as possible for service.

Automatic arming

The vehicle is armed immediately after switching the ignition to the off

position.

The theft indicator will flash every

two seconds to act as a theft

deterrent when the vehicle is

armed.

Automatic disarming

The vehicle is disarmed immediately after the ignition is turned to the on

position.

The theft indicator will illuminate for three seconds and then go out. If

the theft indicator stays on for an extended period of time or flashes

rapidly, contact your authorized dealer as soon as possible.

Locks and Security

117

2010 Edge (edg)

Owners Guide, 3rd Printing

USA (fus)

Replacement integrated keyhead transmitters (IKT) and coded keys

Note: Your vehicle comes equipped with two integrated keyhead

transmitters (IKTs). The IKT functions as both a programmed ignition

key that operates all the locks and starts the vehicle, as well as a remote

keyless entry transmitter. A maximum of eight coded keys can be

programmed to your vehicle; only four of these eight keys can be IKTs

with remote entry functionality.

If your IKTs or standard SecuriLock威 coded keys are lost or stolen and

you don’t have an extra coded key, you will need to have your vehicle

towed to an authorized dealer. The key codes need to be erased from

your vehicle and new coded keys will need to be programmed.

Replacing coded keys can be very costly. Store an extra programmed key

away from the vehicle in a safe place to help prevent any

inconveniences. Please visit an authorized dealer to purchase additional

spare or replacement keys.

Programming spare keys

You can program your own integrated keyhead transmitters or standard

SecuriLock威 coded keys to your vehicle. This procedure will program

both the engine immobilizer keycode and the remote entry transmitter

portion of the IKT to your vehicle. Note: A maximum of eight coded

keys can be programmed to your vehicle; only four of these eight can be

IKTs with remote entry functionality.

Tips:

• Only use integrated keyhead transmitters (IKTs) or standard

SecuriLock威 keys.

• You must have two previously programmed coded keys (keys that

already operate your vehicle’s engine) and the new unprogrammed

key(s) readily accessible.

• If two previously programmed coded keys are not available, you must

take your vehicle to your authorized dealer to have the spare key(s)

programmed.

Locks and Security

118

2010 Edge (edg)

Owners Guide, 3rd Printing

USA (fus)

Please read and understand the

entire procedure before you begin.

1. Insert the first previously

programmed coded key into the

ignition.

2. Turn the ignition from the 1 (off)

position to the 3 (on) position. Keep

the ignition in the 3 (on) position

for at least three seconds, but no more than 10 seconds.

3. Turn the ignition to the 1 (off) position and remove the first coded

key from the ignition.

4. After three seconds but within 10 seconds of turning the ignition to

the 1 (off) position, insert the second previously coded key into the

ignition.

5. Turn the ignition from the 1 (off) position to the 3 (on) position. Keep

the ignition in the 3 (on) position for at least three seconds, but no more

than 10 seconds.

6. Turn the ignition to the 1 (off) position and remove the second

previously programmed coded key from the ignition.

7. After three seconds but within 20 seconds of turning the ignition to

the 1 (off) position and removing the previously programmed coded

key, insert the new unprogrammed key (new key/valet key) into the

ignition.

8. Turn the ignition from the 1 (off) position to the 3 (on) position. Keep

the ignition in the 3 (on) position for at least six seconds.

9. Remove the newly programmed coded key from the ignition.

If the key has been successfully programmed it will start the vehicle’s

engine and will operate the remote entry system (if the new key is an

integrated keyhead transmitter). The theft indicator light will illuminate

for three seconds and then go out to indicate successful programming.

If the key was not successfully programmed, it will not start your

vehicle’s engine and/or will not operate the remote entry features. The

theft indicator light may flash on and off. Wait 20 seconds and you may

repeat Steps 1 through 8. If failure repeats, bring your vehicle to your

authorized dealer to have the new key(s) programmed.

To program additional new unprogrammed key(s), wait 20 seconds and

then repeat this procedure from Step 1.

Locks and Security

119

2010 Edge (edg)

Owners Guide, 3rd Printing

USA (fus)

Locks and Security for Your Ford Edge SUV First Generation (2007-2014)

Related Topics

Popular Owner Manuals

Latest Owner Manuals