Get Locks and Security -> Locks Guide for Ford Edge SUV First Generation (2007-2014)

POWER DOOR LOCKS

• Press the control to unlock all

doors.

• Press the

control to lock all

doors.

Smart locks

This feature helps to prevent you from locking yourself out of the vehicle

if your key is still in the ignition.

When you open one of the front doors or the liftgate and you lock the

vehicle with the power door lock control (on the driver or passenger

door trim panel), all the doors will lock, then all doors will automatically

unlock reminding you that your key is still in the ignition.

The vehicle can still be locked, with the key in the ignition, by locking

the driver’s door with a key, using the lock control on the remote entry

transmitter portion of your Integrated Keyhead Transmitter, or locking

the vehicle with the keyless entry keypad (if equipped).

If both front doors and the liftgate are closed, the vehicle can be locked

from any method, regardless of whether the key is in the ignition or not.

Autolock feature

The autolock feature will lock all the doors when:

• all the doors are closed,

• the ignition is in the on position,

• you shift into any gear putting the vehicle in motion, and

• the vehicle attains a speed greater than 12 mph (20 km/h).

The autolock feature repeats when:

• any door is opened then closed while the ignition is in the on position

and the vehicle speed is 9 mph (15 km/h) or lower, and

• the vehicle then attains a speed greater than 12 mph (20 km/h).

Locks and Security

104

2010 Edge (edg)

Owners Guide, 3rd Printing

USA (fus)

Deactivating/activating autolock feature

Your vehicle comes with the autolock features activated; there are four

methods to enable/disable this feature:

• Through your authorized dealer,

• by using a power door unlock/lock procedure,

• using a keypad procedure (if equipped), or

• or by using the instrument cluster message center (if equipped). Refer

to Message center in the Instrument Cluster chapter.

Note: The autolock feature can be activated/deactivated independently

of the autounlock feature.

Power door lock switch autolock enable/disable procedure

Before starting, ensure the ignition is in the off position and all vehicle

doors are closed. You must complete Steps 1–5 within 30 seconds or the

procedure will have to be repeated. If the procedure needs to be

repeated, wait a minimum of 30 seconds before beginning again.

1. Place the key in the ignition and

turn the ignition to the on position.

2. Press the power door unlock

control on the door panel three

times.

3. Turn the ignition from the on

position to the off position.

4. Press the power door unlock

control on the door panel three

times.

5. Turn the ignition back to the on position. The horn will chirp one time

to confirm programming mode has been entered and is active.

6. To enable/disable the autolock feature, press the unlock control, then

press the lock control. The horn will chirp once if autolock was

deactivated or twice (one short and one long chirp) if autolock was

activated.

7. Turn the ignition to the off position. The horn will chirp once to

confirm the procedure is complete.

Locks and Security

105

2010 Edge (edg)

Owners Guide, 3rd Printing

USA (fus)

Keyless entry keypad autolock enable/disable procedure

1. Turn the ignition to the off

position.

2. Close all the doors.

3. Enter factory–set 5–digit entry

code.

4. Press and hold the 3 • 4. While holding the 3 • 4pressthe7• 8.

5. Release the 7 • 8.

6. Release the 3 • 4.

The user should receive a horn chirp to indicate the system has been

disabled or a chirp followed by a honk to indicate the system has been

enabled.

Autounlock feature

The autounlock feature will unlock all the doors when:

• the ignition is in the on position, all the doors are closed, and the

vehicle has been in motion at a speed greater than 12 mph (20 km/h);

• the vehicle has then come to a stop and the ignition is turned to the

off or accessory position; and

• the driver door is opened within 10 minutes of the ignition being

transitioned to the off or accessory position.

Note: The doors will not autounlock if the vehicle has been

electronically locked before the driver door is opened.

Deactivating/activating autounlock feature

Your vehicle comes with the autounlock features activated; there are four

methods to enable/disable this feature:

• Through your authorized dealer,

• by using a power door unlock/lock sequence,

• using a keypad procedure (if equipped), or

• or by using the instrument cluster message center (if equipped). Refer

to Message center in the Instrument Cluster chapter.

Note: The autounlock feature can be activated/deactivated

independently of the autolock feature.

Locks and Security

106

2010 Edge (edg)

Owners Guide, 3rd Printing

USA (fus)

Power door lock switch autounlock enable/disable procedure

Before starting, ensure the ignition is in the off position and all vehicle

doors are closed. You must complete Steps 1–5 within 30 seconds or the

procedure will have to be repeated. If the procedure needs to be

repeated, wait a minimum of 30 seconds before beginning again.

1. Place the key in the ignition and

turn the ignition to the on position.

2. Press the power door unlock

control on the door panel three

times.

3. Turn the ignition from the on

position to the off position.

4. Press the power door unlock

control on the door panel three

times.

5. Turn the ignition back to the on position. The horn will chirp one time

to confirm programming mode has been entered and is active.

6. To enable/disable the autounlock feature, press the lock control, then

press the unlock control. The horn will chirp once if autounlock was

deactivated or twice (one short and one long chirp) if autounlock was

activated.

7. Turn the ignition to the off position. The horn will chirp once to

confirm the procedure is complete.

Keyless entry keypad autounlock enable/disable procedure

1. Turn the ignition to the off

position.

2. Close all the doors.

3. Enter factory–set 5–digit entry

code.

4. Press and hold the 3 • 4. While holding the 3 • 4, press and release

the 7 • 8. While still holding the 3 • 4, press and release the 7 • 8a

second time.

5. Release the 3 • 4.

The user should receive a horn chirp to indicate the system has been

disabled or a chirp followed by a honk to indicate the system has been

enabled.

Locks and Security

107

2010 Edge (edg)

Owners Guide, 3rd Printing

USA (fus)

CHILDPROOF DOOR LOCKS

• When these locks are set, the

rear doors cannot be opened from

the inside.

• The rear doors can be opened

from the outside when the

childproof door locks are set, but

the doors are unlocked.

The childproof locks are located on

the rear edge of each rear door and

must be set separately for each

door. Setting the lock for one door

will not automatically set the lock

for both doors.

• Insert the key and turn to the

lock position (key horizontal) to

engage the childproof locks.

• Insert the key and turn to the

unlock position (key vertical) to

disengage the childproof locks.

REMOTE ENTRY SYSTEM

The Integrated Keyhead Transmitter (IKT) complies with part 15 of the

FCC rules and with RSS-210 of Industry Canada. Operation is subject to

the following two conditions: (1) This device may not cause harmful

interference, and (2) This device must accept any interference received,

including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to

operate the equipment.

Locks and Security

108

2010 Edge (edg)

Owners Guide, 3rd Printing

USA (fus)

There are two possible types of IKTs:

• Vehicles equipped with a power

liftgate

• Vehicles not equipped with a

power liftgate

The typical operating range for your IKT is approximately 33 feet

(10 meters). A decrease in operating range could be caused by:

• weather conditions,

• nearby radio towers,

• structures around the vehicle, or

• other vehicles parked next to your vehicle.

Locks and Security

109

2010 Edge (edg)

Owners Guide, 3rd Printing

USA (fus)

The IKT allows you to:

• remotely unlock the vehicle doors.

• remotely lock all the vehicle doors.

• remotely open the power liftgate (if equipped).

• activate the personal alarm.

• operate the illuminated entry feature.

The remote entry lock/unlock feature operates in any ignition position

except while the key is held in the start position. The panic feature

operates with the key in the off position.

If there are problems with the remote entry system, make sure to take

ALL Integrated Keyhead Transmitters with you to the authorized

dealer in order to aid in troubleshooting the problem.

Unlocking the doors/two stage unlock

1. Press and release to unlock the driver’s door. Note: The interior

lamps and parking lamps will illuminate.

2. Press

and release again within three seconds to unlock all the

doors.

The remote entry system activates the illuminated entry feature; this

feature turns on the lamps for 25 seconds or until the ignition is turned

to the on position.

The battery saver feature will turn off the lamps 10 minutes after the

ignition is turned to the off position.

Two stage unlocking may be disabled or re-enabled by simultaneously

pressing the

and controls on the IKT for four seconds (disabling

two stage unlock allows all vehicle doors to unlock simultaneously). The

parking lamps will flash twice to indicate that two-stage unlock was

enabled or disabled.

Locking the doors

1. Press and release to lock all the doors. The parking lamps will

illuminate.

2. Press

and release again within three seconds to confirm that all

the doors are closed. Note: The doors will lock again, the horn will chirp

and the turn lamps will illuminate if all the doors and liftgate are closed.

Note: If any door or the liftgate is not closed, the horn will chirp twice

and the lamps will not flash.

Locks and Security

110

2010 Edge (edg)

Owners Guide, 3rd Printing

USA (fus)

Opening the power liftgate (if equipped)

Press twice within three seconds to fully unlatch and open the

liftgate.

WARNING: Make sure all persons are clear of the liftgate area

before using power liftgate control.

In order to fully lower and latch the liftgate, press the control twice.

If the liftgate stops mid travel, it may have detected an obstacle, Check

to ensure the liftgate swing zone is free from obstruction and reset the

power assist by manually closing the liftgate. Normal operation can then

be resumed.

WARNING: Make sure the liftgate is closed to prevent exhaust

fumes from being drawn into the vehicle. This will also prevent

passengers and cargo from falling out. If you must drive with the

liftgate open, keep the vents open so outside air comes into the

vehicle.

Car finder

Press

twice within three seconds. The horn will chirp and the turn

lamps will flash. It is recommended that this method be used to locate

your vehicle, rather than using the panic alarm.

Sounding a panic alarm

Press

to activate the alarm. The horn will sound and the turn lamps

will flash for a maximum of three minutes. Press again or turn the

ignition to the on position to deactivate, or wait for the alarm to time out

in three minutes.

Note: The panic alarm will only operate when the ignition is in the off

position.

Memory feature (seat and mirrors)

The integrated keyhead transmitter (IKT) allows you to recall the

memory seat and power mirrors feature.

Locks and Security

111

2010 Edge (edg)

Owners Guide, 3rd Printing

USA (fus)

Press to automatically move the driver seat, power mirrors and

adjustable pedals to the desired memory position. The mirrors will move

to the programmed position and the seat will move to the easy entry

position. The seat will move to the final position when the key is in the

ignition (if easy entry feature is enabled).

Programming the memory feature to the transmitter

To activate this feature:

1. Move the driver seat and power mirrors to the desired positions using

the associated controls.

2. Press and hold control button 1

for five seconds. A tone will be

heard after two seconds confirming

memory position has been set.

Continue to hold until a second tone

is heard after five seconds.

3. Within three seconds press

the

4. A tone will be heard when the

transmitter programming is

complete.

5. Press the

6. Repeat this procedure for memory 2 and another transmitter if

desired.

Deprogramming the memory feature from the transmitter

To deactivate this feature:

1. Press and hold either the 1 or 2 control on the driver’s door for five

seconds. A tone will be heard after 1

⁄

seconds when the memory store

is done, continue to hold until a second tone is heard after five seconds.

2. Within three seconds press the

3. A tone will be heard when the deactivation is complete.

4. Repeat this procedure for another transmitter if desired.

Replacing the battery

The integrated keyhead transmitter uses one coin type three-volt lithium

battery CR2032 or equivalent.

Locks and Security

112

2010 Edge (edg)

Owners Guide, 3rd Printing

USA (fus)

To replace the battery:

1. Twist a thin coin in the slot of the

IKT near the key ring in order to

remove the battery cover.

Note: Do not wipe off any grease on

the battery terminals on the back

surface of the circuit board.

2. Remove the old battery.

Note: Please refer to local

regulations when disposing of

transmitter batteries.

3. Insert the new battery. Refer to

the instructions inside the IKT for

the correct orientation of the

battery. Press the battery down to

ensure that the battery is fully

seated in the battery housing cavity.

4. Snap the battery cover back onto

the key.

Note: Replacement of the battery will not cause the IKT to become

deprogrammed from your vehicle. The IKT should operate normally after

battery replacement.

Replacing lost integrated keyhead transmitters (IKTs)

If you would like to have your integrated keyhead transmitters

reprogrammed because you lost one, or would like to buy additional

IKTs, you can either reprogram them yourself, or take all IKTs to your

authorized dealer for reprogramming.

How to reprogram your integrated keyhead transmitters (IKTs)

To program a new integrated keyhead transmitter yourself, refer to

Programming spare keys in the SecuriLock威 passive anti-theft system

section of this chapter. Note: At least two IKTs are required to perform

this procedure yourself.

Illuminated entry

The interior lamps, parking lamps and puddle lamps (if equipped)

illuminate when the Integrated Keyhead Transmitter or the keyless entry

system keypad is used to unlock the door(s).

Locks and Security

113

2010 Edge (edg)

Owners Guide, 3rd Printing

USA (fus)

The illuminated entry system will turn off the lights if:

• the ignition is turned to the on position, or

• the Integrated Keyhead Transmitter lock control is pressed, or

• the vehicle is locked using the keyless entry keypad (if equipped), or

• after 25 seconds of illumination.

The lights will not turn off if:

• they have been turned on with the dimmer control, or

• any door is open.

Illuminated exit

• When all vehicle doors are closed and the key is removed from the

ignition, the interior dome lamps, parking lamps and the puddle lamps

(if equipped) will illuminate.

The lamps will turn off if all the doors remain closed and

• 25 seconds elapse, or

• the key is inserted in the ignition.

Battery saver

The battery saver will shut off the lamps 10 minutes after the ignition

has been turned to the off position.

• If the dome lamps were turned on using the panel dimmer control, the

battery saver will shut them off 10 minutes after the ignition has been

turned to the off position.

• If the courtesy lamps were turned on because one of the vehicle doors

or the liftgate was opened, the battery saver will shut them off

10 minutes after the ignition has been turned to the off position.

• The battery saver will shut off the headlamps 10 minutes after the

ignition has been turned to the off position.

SECURICODE™ KEYLESS ENTRY SYSTEM (IF EQUIPPED)

You can use the keyless entry

keypad to:

• lock or unlock the doors without

using a key.

• recall memory seat/power mirrors

positions (if equipped).

Locks and Security

114

2010 Edge (edg)

Owners Guide, 3rd Printing

USA (fus)

The keypad can be operated with the factory set 5–digit entry code; this

code is located on the owner’s wallet card in the glove box and is

available from your authorized dealer. You can also create up to three of

your own 5–digit personal entry codes.

When pressing the controls on the keypad, press the middle of the

controls to ensure a good activation.

Programming a personal entry code and keypad association to

memory feature

To create your own personal entry code:

1. Enter the factory set code.

2. Within five seconds press the 1 • 2 on the keypad.

3. Enter your personal 5-digit code. Each number must be entered

within five seconds of each other.

4. For memory recall feature, enter the sixth digit 1 • 2 to store driver 1

settings or 3 • 4 to store driver 2 settings.

Note: Pressing 5 • 6, 7 • 8, or 9 • 0 keypad numbers as a sixth digit

will not recall a driver memory setting.

Note: The factory-set code cannot be associated with a memory setting.

5. The doors will lock then unlock to confirm that your personal entry

code has been programmed to the module.

Tips:

• Do not set a code that uses five of the same number.

• Do not use five numbers in sequential order.

• The factory set code will work even if you have set your own personal

code.

Erasing personal code

1. Enter the factory set 5–digit code.

2. Within five seconds, press the 1 • 2 on the keypad and release.

3. Press and hold the 1 • 2 for two seconds. This must be done within

five seconds of completing Step 2.

All personal codes are now erased and only the factory set 5–digit code

will work.

Anti-scan feature

If the wrong code has been entered seven times (35 consecutive button

presses), the keypad will go into an anti-scan mode. This mode disables

the keypad for one minute and the keypad lamp will flash.

Locks and Security

115

2010 Edge (edg)

Owners Guide, 3rd Printing

USA (fus)

Locks and Security -> Locks for Your Ford Edge SUV First Generation (2007-2014)

Related Topics

Popular Owner Manuals

Latest Owner Manuals