Get Tires, Wheels and Loading -> INFLATING YOUR TIRES Guide for Ford Focus 4 Door Second Generation (2004-2010)

Tires, Wheels and Loading

• Extra load: A class of P-metric or Metric tires designed to carry a

heavier maximum load at 41 psi [43 psi (2.9 bar) for Metric tires].

Increasing the inflation pressure beyond this pressure will not increase

the tire’s load carrying capability.

• kPa: Kilopascal, a metric unit of air pressure.

• PSI: Pounds per square inch, a standard unit of air pressure.

• Cold inflation pressure: The tire pressure when the vehicle has

been stationary and out of direct sunlight for an hour or more and

prior to the vehicle being driven for 1 mile (1.6 km).

• Recommended inflation pressure: The cold inflation pressure found

on the Safety Compliance Certification Label or Tire Label located on

the B-Pillar or the edge of the driver’s door.

• B-pillar: The structural member at the side of the vehicle behind the

front door.

• Bead area of the tire: Area of the tire next to the rim.

• Sidewall of the tire: Area between the bead area and the tread.

• Tread area of the tire: Area of the perimeter of the tire that

contacts the road when mounted on the vehicle.

• Rim: The metal support (wheel) for a tire or a tire and tube assembly

upon which the tire beads are seated.

INFLATING YOUR TIRES

Safe operation of your vehicle requires that your tires are properly

inflated. Every day before you drive, check your tires. If one looks lower

than the others, use a tire gauge to check pressure of all tires and adjust

if required. Remember that a tire can lose up to half of its air pressure

without appearing flat.

At least once a month and before long trips, inspect each tire and check

the tire pressure with a tire gauge (including spare, if equipped). Inflate

all tires to the inflation pressure recommended by Ford Motor Company.

Use a tire gauge to check the tire inflation pressure, including the spare

(if equipped), at least monthly and before long trips. You are strongly

urged to buy a reliable tire pressure gauge, as automatic service station

gauges may be inaccurate. Ford Motor Company recommends the use of

a digital or dial-type tire pressure gauge rather than a stick-type tire

pressure gauge.

Use the recommended cold inflation pressure for optimum tire

performance and wear. Under-inflation or over-inflation may cause

uneven treadwear patterns.

116

2007 Focus (foc)

Owners Guide (post-2002-fmt)

USA (fus)

Tires, Wheels and Loading

Under-inflation is the most common cause of tire failures and

may result in severe tire cracking, tread separation or ЉblowoutЉ,

with unexpected loss of vehicle control and increased risk of injury.

Under-inflation increases sidewall flexing and rolling resistance,

resulting in heat buildup and internal damage to the tire. It also may

result in unnecessary tire stress, irregular wear, loss of vehicle control

and accidents. A tire can lose up to half of its air pressure and not

appear to be flat!

Always inflate your tires to the Ford recommended inflation pressure

even if it is less than the maximum inflation pressure information found

on the tire. The Ford recommended tire inflation pressure is found on

the Safety Compliance Certification Label or Tire Label which is located

on the B-Pillar or the edge of the driver’s door. Failure to follow the tire

pressure recommendations can cause uneven treadwear patterns and

adversely affect the way your vehicle handles.

Maximum Permissible Inflation Pressure is the tire manufacturer’s

maximum permissible pressure and/or the pressure at which the

maximum load can be carried by the tire. This pressure is normally

higher than the manufacturer’s recommended cold inflation pressure

which can be found on the Safety Compliance Certification Label or Tire

Label which is located on the B-Pillar or the edge of the driver’s door.

The cold inflation pressure should never be set lower than the

recommended pressure on the Safety Compliance Certification Label or

Tire Label.

When weather temperature changes occur, tire inflation pressures also

change. A 10° F (6° C) temperature drop can cause a corresponding

drop of 1 psi (7 kPa) in inflation pressure. Check your tire pressures

frequently and adjust them to the proper pressure which can be found

on the Safety Compliance Certification Label or Tire Label.

To check the pressure in your tire(s):

1. Make sure the tires are cool, meaning they are not hot from driving

even a mile.

If you are checking tire pressure when the tire is hot, (i.e. driven more

than 1 mile [1.6 km]), never “bleed” or reduce air pressure. The tires are

hot from driving and it is normal for pressures to increase above

recommended cold pressures. A hot tire at or below recommended cold

inflation pressure could be significantly under-inflated.

117

2007 Focus (foc)

Owners Guide (post-2002-fmt)

USA (fus)

Tires, Wheels and Loading

Note: If you have to drive a distance to get air for your tire(s), check

and record the tire pressure first and add the appropriate air pressure

when you get to the pump. It is normal for tires to heat up and the air

pressure inside to go up as you drive.

2. Remove the cap from the valve on one tire, then firmly press the tire

gauge onto the valve and measure the pressure with the tire gauge.

3. Add enough air to reach the recommended air pressure.

Note: If you overfill the tire, release air by pushing on the metal stem in

the center of the valve. Then recheck the pressure with your tire gauge.

4. Replace the valve cap.

5. Repeat this procedure for each tire, including the spare.

Note: Some spare tires operate at a higher inflation pressure than the

other tires. For T-type/mini-spare tires (see T-Type/Mini-Spare Tire

Information section for description): Store and maintain at 60 psi

(4.15 bar). For Full Size and Dissimilar spare tires (see Dissimilar

Spare Tire/Wheel Information section for description): Store and

maintain at the higher of the front and rear inflation pressure as shown

on the Safety Compliance Certification Label or the Tire Label.

6. Visually inspect the tires to make sure there are no nails or other

objects embedded that could poke a hole in the tire and cause an air

leak.

7. Check the sidewalls to make sure there are no gouges, cuts or bulges.

TIRE CARE

Inspecting your tires

Periodically inspect the tire treads for uneven or excessive wear and

remove objects such as stones, nails or glass that may be wedged in the

tread grooves. Check for holes or cuts that may permit air leakage from

the tire and make necessary repairs. Also inspect the tire sidewalls for

cracking, cuts, bruises and other signs of damage or excessive wear. If

internal damage to the tire is suspected, have the tire demounted and

inspected in case it needs to be repaired or replaced. For your safety,

tires that are damaged or show signs of excessive wear should not be

used because they are more likely to blow out or fail.

118

2007 Focus (foc)

Owners Guide (post-2002-fmt)

USA (fus)

Tires, Wheels and Loading -> INFLATING YOUR TIRES for Your Ford Focus 4 Door Second Generation (2004-2010)

Related Topics

Tires, Wheels and Loading

Popular Owner Manuals

Latest Owner Manuals