Get Driver Controls -> Moon roof Guide for Ford Fusion 4 Door First Generation (2006-2012)

Driver Controls

For further information on the SYNC௡ system, refer to the SYNC௡

supplement.

Navigation system/SYNC௡ hands

free control features (if

equipped)

Press

voice

control briefly until the

icon appears on the

Navigation display to use the voice

command feature.

Press

to activate phone mode or

answer a phone call. Press and

hold

a call.

to exit phone mode or end

For further information on the Navigation system/SYNC௡ system, refer to

the Navigation System and SYNC௡ supplements.

MOON ROOF (IF EQUIPPED)

You can move the glass panel of the moon roof back to open or tilt up

(from the closed position) to ventilate the vehicle.

WARNING: Do not let children play with the moon roof or leave

children unattended in the vehicle. They may seriously hurt

themselves.

To open the moon roof:

The moon roof is equipped with an

automatic, one-touch, express

opening, closing and venting feature.

Press and release the rear portion of

the control. To stop motion at any

time during the one-touch

operation, press the control a

second time.

WARNING: When closing the moon roof, you should verify that

it is free of obstructions and ensure that children and/or pets are

not in the proximity of the moon roof opening.

86

2011 Fusion (fsn)

Owners Guide, 3rd Printing

USA (fus)

Driver Controls

To close the moon roof:

The moon roof is equipped with an automatic, one-touch, express closing

feature. Press and release the front portion of the control. To stop

motion at any time during the one-touch closing, press the control again.

Bounce-back:

When an obstacle has been detected in the moon roof opening as the

moon roof is closing, the moon roof will automatically open and stop at a

prescribed position. This is known as “bounce-back”. If the ignition is

turned off (without accessory delay being active) during bounce-back,

the moon roof will move until the bounce-back position is reached.

Bounce-back override:

To override bounce-back, press and hold the front portion of the control.

For example: Bounce-back can be used to overcome the resistance of ice

on the moon roof or seals. If during a bounce-back condition, the control

is released to the neutral position, then held in the one-touch position

within two seconds after the moon roof reaches the bounce-back

position, the moon roof will travel with no bounce-back protection.

If the control is released before the moon roof reaches fully closed or the

ignition is turned off (without accessory delay being active), the moon

roof will stop. Security override can be used if the moon roof movement

is restricted in some way, for example, if there is ice on the moon roof or

seals.

To vent:

• To tilt the moon roof into the vent position (when the glass panel is

closed), press and release the front portion of the control.

• To close the moon roof from the vent position, press and hold the rear

portion of the control until the glass panel stops moving.

The moon roof has a sliding shade that can be opened or closed when

the glass panel is shut. To close the shade, pull it toward the front of the

vehicle

Accessory delay:

With accessory delay, the window switches, audio system, and moon roof

(if equipped) may be used for up to 10 minutes after the ignition switch

is turned off or until any door is opened.

Note: If equipped with global open windows, you can open the vehicle’s

front windows and moon roof (if equipped) by using the control on the

remote transmitter. Refer to Global open windows earlier in this

chapter.

87

2011 Fusion (fsn)

Owners Guide, 3rd Printing

USA (fus)

Driver Controls

UNIVERSAL GARAGE DOOR OPENER (IF EQUIPPED)

Your vehicle may be equipped with a universal garage door opener which

can be used to replace the common hand-held transmitter.

Car2Uா Home Automation System (if equipped)

The Car2U௡ Home Automation

System is a universal transmitter

located in the driver’s visor that

includes two primary features – a

garage door opener and a platform

for remote activation of devices

within the home. The Car2U௡

system’s garage door opener

function replaces the common

hand-held garage door opener with a three-button transmitter that is

integrated into the interior of your vehicle. After being programmed for

garage doors, the Car2U௡ system transmitter can be programmed to

operate security devices and home lighting systems.

WARNING: Make sure that people and objects are clear of the

garage door or security device you are programming. Do not

program the Car2U௡ system with the vehicle in the garage.

Do not use the Car2U௡ system with any garage door opener that lacks

safety stop and reverse features as required by U.S. Federal Safety

Standards (this includes any garage door opener manufactured before

April 1, 1982).

Be sure to keep the original remote control transmitter for use in other

vehicles as well as for future Car2U௡ system programming. It is also

recommended that upon the sale or lease termination of the vehicle, the

programmed Car2U௡ system buttons should be erased for security

reasons. Refer to Erasing the Car2U௡ Home Automation System

buttons later in this section.

Read the instructions completely before attempting to program the

Car2U௡ system. Because of the steps involved, it may be helpful to have

another person assist you in programming the transmitter.

Additional Car2U௡ system information can be found on-line at

www.learcar2U.com or by calling the toll-free Car2U௡ system help line at

1-866-572-2728.

88

2011 Fusion (fsn)

Owners Guide, 3rd Printing

USA (fus)

Driver Controls

Types of garage door openers (rolling code and fixed code)

The Car2U௡ Home Automation System may be programmed to operate

rolling code and fixed code garage door openers.

• Rolling code garage door openers were produced after 1996 and are

code protected. Rolling code means the coded signal is changed every

time your remote control garage door opener is used.

• Fixed code garage door openers were produced prior to 1996. Fixed

code uses the same coded signal every time. It is manually

programmed by setting DIP switches for a unique personal code.

If you do not know if your garage

door opener is a rolling code or

O

N

1

2

4

5

9

11

12

10

3

6

7

8

fixed code device, open your garage

door opener’s remote control battery

cover. If a panel of DIP switches is

present your garage door opener is

a fixed code device. If not, your

garage door opener is a rolling code

device.

CTS 206-12

T

124

Note: Programming the Car2U௡ system to a community gate will require

a unique set of instructions depending on the gate system model.

Contact the Car2U௡ help line at 1-866-572-2728 to program your Car2U௡

system.

Note: Accidentally entering the program mode may override previously

programmed buttons. This can happen by pressing and releasing the

outer two buttons, or all three buttons, simultaneously. If this happens,

do not press any button until the module times out after approximately

2.5 seconds and resets to normal mode. When time-out occurs, all three

LEDs will flash rapidly for a few seconds then turn off. Any settings

should remain as previously set.

Rolling code programming

Note: Programming the rolling code garage door opener involves

time-sensitive actions. Read the entire procedure prior to beginning so

you will know which actions are time-sensitive. If you do not follow the

time-sensitive actions, the device will time out and you will have to

repeat the procedure.

Note: Do not program the Car2U௡ system with the vehicle in the garage.

Make sure that your key is on and engine off while programming the

transmitter.

89

2011 Fusion (fsn)

Owners Guide, 3rd Printing

USA (fus)

Driver Controls

1. Firmly press the two outer

Car2U௡ system buttons for

1–2 seconds, then release.

2. Go to the garage to locate the

garage door opener motor and its

“learn” button. You may need a

ladder to reach the unit and you

may need to remove the unit’s cover

or light lens to locate the “learn”

button. Press the “learn” button,

after which you will have

10–30 seconds to return to your

vehicle and complete the following

steps. If you cannot locate the

“learn” button, refer to the Owner’s Guide of your garage door opener or

call the toll-free Car2U௡ system help line at 1-866-57Car2U

(1-866-572-2728).

3. Return to your vehicle. Press and

hold the Car2U௡ system button you

would like to use to control the

garage door. You may need to hold

the button from 5–20 seconds,

during which time the selected

button indicator light will blink

slowly. Immediately (within

1 second) release the button once the garage door moves. When the

button is released, the indicator light will begin to blink rapidly until

programming is complete.

4. Press and release the button again. The garage door should move,

confirming that programming is successful. If your garage door does not

operate, repeat the previous steps in this section.

After successful programming, you will be able to operate your Car2U௡

system by pressing the button you programmed to activate the opener.

90

2011 Fusion (fsn)

Owners Guide, 3rd Printing

USA (fus)

Driver Controls

The indicator light above the selected button will turn on to confirm that

the Car2U௡ system is responding to the button command.

To program another rolling code device such as an additional garage door

opener, a security device or home lighting, repeat Steps 1 through 4

substituting a different function button in Step 3 than what you used for

the garage door opener. For example, you could assign the left-most

button to the garage door, the center button to a security device, and

the right-most button to another garage door opener.

Note: The Car2U௡ system allows for three devices to be programmed. If

you need to change or replace any of the three devices after it has been

initially programmed, it is necessary to erase the current settings using

the Erasing the Car2U௡ Home Automation System buttons procedure

and then programming all of the devices being used.

Fixed code programming

Note: Do not program the Car2U௡ system with the vehicle in the garage.

Make sure that your key is on and engine off while programming the

transmitter.

1. To program units with fixed code DIP switches, you will need the

garage door hand-held transmitter, paper and a pen or pencil.

2. Open the battery cover and record the switch settings from left to

right for all 8 to 12 switches. Use the figure below:

When a switch is in the up, on, or + position, circle “L.”

When a switch is in the middle, neutral, or 0 position, circle “M.”

When a switch is in the down, off, or – position, circle “R.”

91

2011 Fusion (fsn)

Owners Guide, 3rd Printing

USA (fus)

Driver Controls

Switch

position

Up, on

or +

Middle,

neutral

or 0

1

2

3

4

5

6

7

8

9

10 11 12

L

M

R

L

M

R

L

M

R

M

R

M

R

M

R

M

R

M

R

Down,

off or –

R

L=left; M=middle; R=right

3. To input these positions into the

Car2U௡ system, simultaneously

press all three Car2U௡ system

buttons for a few seconds and then

release to put the device into

programming mode. The indicator

lights will blink slowly. Within

2.5 minutes enter your

corresponding DIP switch settings

from left to right into your Car2U௡ system by pressing and releasing the

buttons corresponding to the settings you circled.

4. After inputting switch settings, simultaneously press and release all

three Car2U௡ system buttons. The indicator lights will turn on.

5. Press and hold the Car2U௡

system button you would like to use

to control the garage door.

Immediately (within 1 second)

release the button once the garage

door moves. During this time the

selected button indicator light will

blink slowly. Do not release the

button until you see the garage door move. Most garage doors open

quickly. You may need to hold the button from 5–55 seconds before

observing movement of the garage door.

6. The indicator light will (begin to) blink rapidly until programming is

complete. If your garage door opener does not operate following these

steps, repeat Steps 2 through 6. Otherwise, call the toll-free Car2U௡ help

line at 1-866-57Car2U (1-866-572-2728).

92

2011 Fusion (fsn)

Owners Guide, 3rd Printing

USA (fus)

Driver Controls

After successful programming, you will be able to operate your Car2U௡

system by pressing the button you programmed to activate the opener.

The indicator light above the selected button will turn on to confirm that

the Car2U௡ system is responding to the button command.

Erasing the Car2Uா Home Automation System buttons

Note: The system allows for three devices to be programmed. If you

need to change or replace any of the three devices after it has been

initially programmed, it will be necessary to erase the current settings

using the procedure below and then reprogramming all of the devices

being used.

To erase programming on the Car2U௡ system (individual buttons cannot

be erased), use the following procedure:

1. Firmly press the two outside

Car2U௡ system buttons

simultaneously for approximately

20 seconds until the indicator lights

begin to blink rapidly. The indicator

lights are located directly above the

buttons.

2. Once the indicator lights begin to

blink, release your fingers from the

buttons. The codes for all buttons

are erased.

If you sell your vehicle equipped with the Car2U௡ system, it is

recommended that you erase the programming for security reasons.

FCC and RSS-210 Industry Canada Compliance

The Car2U௡ system complies with Part 15 of the FCC rules and with

RSS-210 of Industry Canada. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2)

This device must accept any interference received including interference

that may cause undesired operation.

Changes and modifications to the Car2U௡ system transmitter by other

than an authorized service facility could void authorization to use the

equipment.

93

2011 Fusion (fsn)

Owners Guide, 3rd Printing

USA (fus)

Driver Controls

POSITIVE RETENTION FLOOR MAT

WARNING: Do not install additional floor mats on top of the

factory installed floor mats as they may interfere with the

accelerator or the brake pedals.

Position the floor mat so that the

eyelets are over the retention posts

and press down to lock in. Make

sure that the mat does not interfere

with the operation of the accelerator

or the brake pedal. To remove the

floor mat, reverse the installation

procedure.

INTERIOR TRUNK CONTROL

Press the remote trunk release

control on the instrument panel to

the left of the steering wheel.

94

2011 Fusion (fsn)

Owners Guide, 3rd Printing

USA (fus)

Driver Controls -> Moon roof for Your Ford Fusion 4 Door First Generation (2006-2012)

Related Topics

Driver Controls

Popular Owner Manuals

Latest Owner Manuals