Get Climate Control Guide for Ford Mondeo 4 Door Fifth Generation (2014-2022)

Information Displays

Tire pressure monitoring system

Message

Indicator

Action

Check ..... tyre!

red

The tire indicated has continued to deflate. Check

the tire and inflate it to the recommended pres-

sure. See Technical Specifications (page 199).

Check tyre pres-

sures

red

One or more of the tires are significantly under-

inflated. This message may be displayed after a

new sensor has been installed. Check the tires

and inflate them to the recommended pressure.

See Technical Specifications (page 199).

Check ..... tyre

amber

The tire indicated is significantly under-inflated.

Check the tire and inflate it to the recommended

pressure. See Technical Specifications (page

199).

Tyre monitor

malfunction

You have installed a temporary spare wheel.

Install a correctly inflated full size wheel with a

sensor as soon as possible. When a malfunction

occurs, the system may not be able to detect or

signal low tire pressure.

Up to three sensors have malfunctioned, an

unapproved accessory is interfering with the

system or a general malfunction has been

detected. Have the system checked by a properly

trained technician as soon as possible. When a

malfunction occurs, the system may not be able

to detect or signal low tire pressure.

Inflate tyres for high

speed

amber

The tire pressures are not suitable for driving at

160 km/h (100 mph). Inflate the tires to the

recommended pressure. See Technical

Specifications (page 199). This message will be

displayed for only a few seconds with a low tire

pressure warning.

Tyre sensors not

detected

-

You have installed wheels and tires that do not

have sensors. The tire pressures will not be

monitored.

All sensors have malfunctioned or an unapproved

accessory is interfering with the system. Have the

system checked by a properly trained technician

as soon as possible.

96

Mondeo (CA2) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 31-12-2014, CG3536en enGBR, Edition date: 11/2013

Information Displays

Voice control

Message

Indicator

Action

Voice control

Please speak

-

See Voice control (page 281).

Voice control Not

recognised

-

Voice control Not

allowed

97

Mondeo (CA2) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 31-12-2014, CG3536en enGBR, Edition date: 11/2013

Climate Control

Warming the interior

PRINCIPLE OF OPERATION

Outside air

Keep the air intakes forward of the

windshield free from obstruction (snow,

leaves etc.) to allow the climate control

system to function effectively.

Direct the air towards your feet. In cold or

humid weather conditions, direct some of

the air towards the windshield and the

door windows.

Cooling the interior

Direct the air towards your face.

Recirculated air

CAUTION

Prolonged use of recirculated air may

cause the windows to mist up. If the

windows mist up, follow the settings

for defrosting and demisting the

windshield.

AIR VENTS

Front air vents

The air currently in the passenger

compartment will be recirculated. Outside

air will not enter the vehicle.

Heating

Heating performance depends on the

Rear air vents

temperature of the engine coolant.

Air conditioning

Note: The air conditioning operates only

when the temperature is above 4°C (39°F).

Note: If you use the air conditioning, the

fuel consumption of your vehicle will be

higher.

Air is directed through the evaporator

where it is cooled. Humidity is extracted

from the air to help keep the windows free

of mist. The resulting condensation is

directed to the outside of the vehicle and

it is therefore normal if you see a small

pool of water under your vehicle.

A

B

Open

Close

General information on controlling

the interior climate

Fully close all the windows.

98

Mondeo (CA2) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 31-12-2014, CG3536en enGBR, Edition date: 11/2013

Climate Control

Blower

MANUAL CLIMATE CONTROL

Air distribution control

A

Off

Note: If you switch the blower off, the

windshield may mist up.

A

B

C

D

E

F

Windshield

Footwell and windshield

Footwell

Face level and footwell

Face level

Face level and windshield

Recirculated air

Press the button to toggle between outside

air and recirculated air.

You can set the air distribution control to

any position between the symbols.

Heating the interior quickly

99

Mondeo (CA2) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 31-12-2014, CG3536en enGBR, Edition date: 11/2013

Climate Control

Cooling the interior quickly

Ventilation

Set the air distribution control, blower and

air vents to suit your requirements.

Defrosting and demisting the

windshield

Air conditioning

Note: Turn the air conditioning on to assist

windshield and side window demisting.

Switching the air conditioning on and

off

Note: Turn the heater control to maximum

heat to assist windshield and side window

defrosting.

If you turn the blower off, the air

conditioning will turn off. When you turn

the blower on again, the air conditioning

will come on automatically.

Cooling with outside air

Make sure that the blower and A/C is on.

The indicator in the switch will illuminate

during defrosting and demisting.

If you move the air distribution control to

a position other than A, the A/C will

remain on.

You can switch the air conditioning and

recirculated air on and off while the air

distribution control is set to position A.

If necessary, switch the heated windows

on. See Heated Windows and Mirrors

(page 103).

100

Mondeo (CA2) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 31-12-2014, CG3536en enGBR, Edition date: 11/2013

Climate Control

Reducing interior air humidity

AUTOMATIC CLIMATE CONTROL

Note: Avoid adjusting the settings when

the vehicle interior is extremely hot or cold.

The automatic climate control adjusts to

the current circumstances automatically.

For the system to function properly, the side

and center vents should be fully open.

Note: The sunload sensor is located on top

of the instrument panel. Do not cover the

sensor with any objects.

Note: At low outside temperatures, when

the system is in auto mode, the air stream

will be directed to the windshield and the

side windows as long as the engine is cold.

Note: For information on the automatic

climate control, on vehicles fitted with a

combined Navigation and automatic

climate control system, see separate

handbook.

The system controls the temperature,

amount and distribution of the air flow

automatically and adjusts them according

to the driving and weather conditions.

Pressing the AUTO button once switches

on the auto mode.

The system in your vehicle is dual-zone

automatic climate control. When the

system is in mono mode, all the

temperature zones are linked to the driver's

zone. When you switch mono mode off,

the dual-zone system allows you to set

different temperatures for the driver's and

front passenger's side.

101

Mondeo (CA2) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 31-12-2014, CG3536en enGBR, Edition date: 11/2013

Climate Control

Note: If you set one of the sides to HI or LO,

Setting the temperature

both sides will be set to HI or LO.

To switch mono mode back on

To switch mono mode back on,

press the MONO button.

MONO reappears in the display

and the passenger’s side temperature will

be adjusted to the driver’s side

temperature.

You can set the temperature between

15.5ºC (60°F) and 29.5ºC (85°F) in steps

of 0.5ºC (1°F). In position LO, 15ºC (59°F),

the system will switch to permanent

cooling. In position HI, 30°C (86°F), the

system will switch to permanent heating.

Note: If either position LO or HI is selected,

the system will not regulate a stable

temperature.

Blower

Use the buttons to adjust the

blower speed.

The blower setting is indicated in the

display.

Mono mode

To return to auto mode, press the AUTO

In mono mode, the temperature settings

for both the driver’s and passenger’s side

are linked. If you adjust the temperature

using the rotary control on the driver’s side,

the settings will be adjusted to the same

setting on the passenger’s side. In mono

mode, MONO appears in the display.

button.

Air distribution

To adjust air distribution, press the desired

button. Any combination of settings can

be selected simultaneously.

To switch mono mode off

Select a temperature for the passenger’s

side with the rotary control on the

passenger’s side. Mono mode will switch

off and MONO disappears from the

display. The temperature for the driver’s

side will remain unchanged. You can now

adjust the driver and passenger side

temperatures independently of each

another. The temperature settings for each

side are shown in the display. You can set

a temperature difference of up to 4ºC

(8°F).

A

B

C

Footwell

Face level

Windshield

When you select windshield defrosting and

demisting, A, B and C switch off

Note: If you set a temperature difference

of greater than 4ºC (8°F), the temperature

on the other side will be adjusted so that

the difference remains 4ºC (8°F).

automatically and the air conditioning

switches on. Outside air will flow into the

vehicle. You cannot select recirculated air.

102

Mondeo (CA2) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 31-12-2014, CG3536en enGBR, Edition date: 11/2013

Climate Control

Windshield defrosting and

demisting

Switching off the automatic

climate control

Press the windshield defrosting

Press the OFF button.

and demisting button. Outside

air will flow into the vehicle. Air

conditioning is automatically selected. As

long as the air distribution is set to this

position, you cannot select recirculated air.

When switched off, the heating, ventilation

and air conditioning system is switched off

and recirculated air is selected.

The blower speed and the temperature

control operate automatically and cannot

be adjusted manually. The blower is set to

high speed and the temperature to HI.

When you select windshield defrosting and

demisting, the heated screens switch on

automatically and switch off after a short

time.

HEATED WINDOWS AND

MIRRORS

Heated windows

Use the heated windows to defrost or

demist the windshield or rear window.

Note: The heated windows operate only

To return to auto mode, press the AUTO

when the engine is running.

button.

Heated windshield

Switching the air conditioning on

and off

Press the A/C button to switch

the air conditioning on and off.

A/COFF appears in the display

Heated rear window

Heated exterior mirrors

Electric exterior mirrors are fitted with a

heating element that will defrost or demist

the mirror glass. They will switch on

automatically when you switch the heated

rear window on.

when the air conditioning is switched off.

A/C ON appears in the display when the

air conditioning is switched on.

Recirculated air

Press the recirculated air button

to toggle between outside air

and recirculated air.

Note: When the system is in auto mode and

the interior and exterior temperatures are

quite hot, the system selects recirculated

air automatically to maximize cooling of the

interior. Once the selected temperature is

reached, the system will reselect outside air

automatically.

103

Mondeo (CA2) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 31-12-2014, CG3536en enGBR, Edition date: 11/2013

Climate Control

•

Once the parking heater has performed

AUXILIARY HEATER

Parking heater

one heating cycle, the next

programmed heating cycle will only be

carried out if you have started the

vehicle’s engine in between.

After a heating cycle, drive the vehicle

for at least the period of the heating

cycle.

WARNING

•

The parking heater must not be

operated at filling stations, near

sources of combustible vapors or

dust or in enclosed spaces.

Program the parking heater

Note: The programmed time is the time at

which you wish the vehicle to be warm and

ready to drive, not the time at which the

heater switches on.

Note: You must program the times at least

70 minutes in advance of the time you wish

to set.

The parking heater operates independently

of the vehicle heater by heating the

engine’s coolant circuit. It is fed from the

vehicle fuel tank. You can also use it while

the vehicle is in motion to help the vehicle

heater warm up the interior more quickly.

Used properly, the parking heater provides

the following benefits:

Note: You must set the time and date

correctly. See Clock (page 219).

•

It preheats the interior of the vehicle.

To program the heating times:

It keeps the windows clear of ice in the

event of frost and prevents

condensation.

•

It avoids cold starts and allows the

engine to reach operating temperature

sooner.

Note: The parking heater will only operate

if there is at least 7.5 liters (1.6 gallons) of

fuel in the fuel tank and the ambient

temperature is below 15°C (59°F). The

heater will not operate if the battery is low.

Note: The heating depends on the outside

air temperature.

Note: When the parking heater is activated,

exhaust fumes may come from under the

sides of the vehicle. This is normal.

Note: On vehicles with a manual heating,

ventilation and air conditioning system, the

heating of the vehicle interior is dependent

on the temperature, air distribution and

blower control settings.

1. Press the right arrow button on the

steering wheel to enter the main menu.

2. Highlight Setup with the up and down

arrow buttons and press the right arrow

button.

3. Highlight Park Heater and press the

right arrow button.

To prevent the battery from discharging:

104

Mondeo (CA2) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 31-12-2014, CG3536en enGBR, Edition date: 11/2013

Climate Control

1. Highlight Program 1 and press the right

arrow button.

2. Highlight the day on which the heater

should warm up the vehicle.

3. Press the OK button to confirm the

selection. A cross appears in the box

next to the day to show that this day is

selected.

4. Continue in the same way to select all

the days on which the heater should

warm up the vehicle.

5. To set the time at which the vehicle

should be warmed up, highlight the

time at the top of the display and press

the right arrow button.

•

The functions Program 1 and

Program 2 allow you to program up

to two heating cycles for each day of

the week. These times will remain

stored and the heater will warm up the

vehicle at these times on these days

every week.

The function One-Time allows you to

program one heating cycle for one

specific day.

6. Press the OK button and the hours

flash. Use the up and down arrow

buttons to adjust the individual settings

and the left and right arrow buttons to

move to the next or previous setting.

7. When you have finished, press the OK

button again to confirm the selection.

•

The function Active now

automatically switches on the heater.

Programming the functions Program 1

and Program 2

You can use the function Program 2 to set

a second cycle, for example different times

on different days or twice on the same day.

The programming procedure is the same

as for the function Program 1.

105

Mondeo (CA2) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 31-12-2014, CG3536en enGBR, Edition date: 11/2013

Climate Control

Programming the function One-Time

Starting

1. Highlight One-Time and press the right

Hold the transmitter with the antenna

upwards and press the ON button for at

least two seconds. The LED on the

transmitter lights up green to confirm the

signal has been received.

arrow button.

2. Press the OK button and the hours

flash. Use the up and down arrow

buttons to adjust the individual settings

and the left and right arrow buttons to

move to the next or previous setting.

Switching off

Hold the transmitter with the antenna

upwards and press the OFF button for at

least two seconds. The LED on the

transmitter lights up red to confirm the

signal has been received.

3. When you have finished, press the OK

button again to confirm the selection.

Active now

Highlight Active now and press the OK

button. A cross appears in the box next to

the function to show that the heater is

activated.

Remote start in combination with

direct start or timer

To deactivate the heater, highlight Active

now and press the OK button again.

Remote starting

The parking heater may be started and

switched off from a distance of up to 500

meters (1640 feet) using the supplied

remote control transmitter. This range will

vary depending upon local conditions and

terrain, as well as battery condition. The

remote control transmitter will indicate

whether or not the signal has been

Remote start is integrated with normal

heater control. Parking heaters started with

direct start or timer functions can be

switched off with the remote control

transmitter and vice versa.

received. The parking heater will operate

for a maximum of 30 minutes.

Note: The heater will operate, depending

on the ambient temperature, for between

10 and 30 minutes. The interior will cool

down after the heating period has elapsed,

therefore a remote start more than 30

minutes before driving is not recommended.

Note: The remote control may not always

receive confirmation of a successful remote

command at extended operating ranges.

Feedback during starting and

switching off

The LED on the transmitter illuminates

green for about two seconds. This

indicates the signal has been received by

the vehicle and the heater has started.

The LED on the transmitter illuminates red

for about two seconds. This indicates the

signal has been received by the vehicle and

the heater has switched off.

106

Mondeo (CA2) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 31-12-2014, CG3536en enGBR, Edition date: 11/2013

Climate Control

The LED on the transmitter flashes green

3. Install a new battery (3.3V type

or red for about two seconds. This

indicates the signal was not transmitted

correctly. Repeat the transmission.

CR1-3N) with the + facing upwards.

4. Re-assemble the remote control.

Programming the transmitter

The LED on the transmitter illuminates

orange for about two seconds before

showing green or red. This indicates the

transmitter batteries are weak and should

be changed.

Further transmitters may be used with the

remote system, please consult your dealer.

Up to a maximum of 3 separate remote

controls may be added. When adding extra

transmitters these must be programmed

separately.

The LED on the transmitter flashes orange

for about 5 seconds. This indicates that

the signal was not transmitted. The

Note: The heater must be switched off

transmitter batteries are discharged and

should be changed as soon as possible.

during programming.

Note: The programming procedure may be

repeated as often as is required. The oldest

programmed transmitter will be deleted

each time.

Changing the remote control

battery

Make sure that you dispose of old batteries

in an environmentally friendly way. Seek

advice from your local authority regarding

recycling.

1. Install the battery in the new

transmitter.

2. Turn off the power to the receiver by

removing fuse F32 from the engine

compartment fuse box. See Fuse

Specification Chart (page 159).

3. Wait for at least 5 seconds.

4. Reconnect power to the receiver by

replacing the fuse, and press the OFF

button on the new transmitter within

5 seconds until the LED light turns off.

5. The new transmitter is now

programmed.

Fuel operated heater (depending

on country)

1. Insert a screwdriver or other suitable

tool into the slot on the back of the

remote control, and unscrew the

compartment cover.

WARNING

The fuel operated heater must not

be operated at filling stations, near

sources of combustible vapors or

dust or in enclosed spaces.

CAUTION

Do not touch the battery contacts or

the printed circuit board with the

screwdriver.

2. Carefully prise out the battery.

107

Mondeo (CA2) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 31-12-2014, CG3536en enGBR, Edition date: 11/2013

Climate Control

The fuel operated heater aids in warming

Diesel auxiliary heater (depending

on country)

the engine and the vehicle interior on

vehicles with a diesel engine. It is switched

on or off automatically depending on the

outside air temperature and the coolant

temperature, unless you have deactivated

it. When the fuel operated heater is

operating, Aux. Heater on is displayed in

the information display. See Information

Displays (page 75).

The diesel auxiliary heater (PTC electrical

heater) aids in warming the vehicle interior

on vehicles with a diesel engine. It is

switched on or off automatically

depending on the outside air temperature,

the coolant temperature and the alternator

load.

To deactivate the fuel operated heater:

POWER MOON ROOF

WARNING

Before operating the power

moonroof you should verify it is free

of obstructions and ensure that

children and/or pets are not in the

proximity of the moonroof opening. Failure

to do so could result in serious personal

injury. It is the primary responsibility of the

supervising adults to never leave a child

unattended in a vehicle and to never leave

the keys in an unattended vehicle.

1. Press the right arrow button on the

steering wheel to enter the main menu.

2. Highlight Setup with the up and down

arrow buttons and press the right arrow

button.

3. Highlight Aux. Heater and press the

OK button to toggle the heater on and

off. A cross appears in the box when

the heater is activated.

4. Press the left arrow button to exit the

menu. Hold the left arrow button

pressed to return to the trip computer

display.

Note: When the switches are operated

often during a short period of time, the

system might become inoperable for a

certain time to prevent damage due to

overheating.

Note: The power moonroof can also be

operated with the ignition off via the global

opening and global closing function. See

Global Opening and Closing (page 37).

There are two ways of opening the

moonroof – the rear of the moonroof lifts

open or the moonroof opens from the

front, sliding back under the roof. The

moonroof opens and closes whilst the

switch is pressed.

Switch on the ignition to operate the power

moonroof.

The power moonroof is operated by a

switch located between the sun visors.

108

Mondeo (CA2) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 31-12-2014, CG3536en enGBR, Edition date: 11/2013

Climate Control

To open or close the moonroof

Opening and closing the moonroof

automatically press either side of the

switch to the second action point and

release it completely. Press again to stop.

When the closed position is reached, the

moonroof stops automatically.

Moonroof anti-trap protection

WARNINGS

The anti-trap function is deactivated

until the memory has been reset.

Careless closing of the window can

cause injuries.

Careless closing of the power

moonroof can override the anti-trap

protection and cause injuries.

Tilting the moonroof

The moonroof will stop automatically

while closing and reverse some distance

if there is an obstacle in the way.

To override anti-trap protection when there

is a resistance, e. g. in the winter, proceed

as follows:

WARNING

While the moonroof is being closed

for the third time, the anti-trap

function is disabled. Make sure there

are no obstacles in the way of the closing

moonroof.

Close the moonroof a third time to the

resistance. The anti-trap function is

disabled and the moonroof cannot be

closed automatically. The moonroof will

override the resistance and can then be

closed fully.

Opening and closing the moonroof

automatically

Note: When opening automatically, the

moonroof will stop about 8 cm from the

fully opened position. This position reduces

the buffeting noise which is sometimes

heard when the moonroof is fully open. The

moonroof will only stop automatically in

this position when the moonroof is opened

automatically.

If the moonroof does not close after the

third attempt, have it checked by an expert.

109

Mondeo (CA2) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 31-12-2014, CG3536en enGBR, Edition date: 11/2013

Climate Control

Moonroof safety mode

WARNING

The anti-trap function is not active

during this procedure. Make sure that

there are no obstacles in the way of

the closing moonroof.

If the system detects a malfunction, it

enters a safety mode. The moonroof will

move for only about 0.5 seconds at a time

and then stop again. Close the moonroof

by pressing the button again when the

moonroof stops moving. When the rear of

the moonroof is lifted, lift the rear all the

way and then close the moonroof. Have

the system checked by an expert

immediately.

Moonroof relearning

WARNING

The anti-trap function is not active

during this procedure. Make sure that

there are no obstacles in the way of

the closing moonroof.

In case the moonroof no longer closes

properly, follow this relearning procedure:

•

Tilt the rear of the moonroof as far as

possible. Release the button.

•

Press and hold the same button again

for 30 seconds until you see the

moonroof move.

•

Release the button and immediately

press and hold it again. The moonroof

will close, open fully and then close

again. Do not release the button before

the moonroof has reached the closed

position for the second time.

If the button is not pressed continuously,

the relearning function will be interrupted.

Start the procedure once more from the

beginning.

110

Mondeo (CA2) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 31-12-2014, CG3536en enGBR, Edition date: 11/2013

Climate Control for Your Ford Mondeo 4 Door Fifth Generation (2014-2022)

Related Topics

Popular Owner Manuals

Latest Owner Manuals