Get Climate Control -> Auxiliary Heater Guide for Ford Mondeo 4 Door Fifth Generation (2014-2022)

Climate Control

•

Once the parking heater has performed

AUXILIARY HEATER

Parking heater

one heating cycle, the next

programmed heating cycle will only be

carried out if you have started the

vehicle’s engine in between.

After a heating cycle, drive the vehicle

for at least the period of the heating

cycle.

WARNING

•

The parking heater must not be

operated at filling stations, near

sources of combustible vapors or

dust or in enclosed spaces.

Program the parking heater

Note: The programmed time is the time at

which you wish the vehicle to be warm and

ready to drive, not the time at which the

heater switches on.

Note: You must program the times at least

70 minutes in advance of the time you wish

to set.

The parking heater operates independently

of the vehicle heater by heating the

engine’s coolant circuit. It is fed from the

vehicle fuel tank. You can also use it while

the vehicle is in motion to help the vehicle

heater warm up the interior more quickly.

Used properly, the parking heater provides

the following benefits:

Note: You must set the time and date

correctly. See Clock (page 219).

•

It preheats the interior of the vehicle.

To program the heating times:

It keeps the windows clear of ice in the

event of frost and prevents

condensation.

•

It avoids cold starts and allows the

engine to reach operating temperature

sooner.

Note: The parking heater will only operate

if there is at least 7.5 liters (1.6 gallons) of

fuel in the fuel tank and the ambient

temperature is below 15°C (59°F). The

heater will not operate if the battery is low.

Note: The heating depends on the outside

air temperature.

Note: When the parking heater is activated,

exhaust fumes may come from under the

sides of the vehicle. This is normal.

Note: On vehicles with a manual heating,

ventilation and air conditioning system, the

heating of the vehicle interior is dependent

on the temperature, air distribution and

blower control settings.

1. Press the right arrow button on the

steering wheel to enter the main menu.

2. Highlight Setup with the up and down

arrow buttons and press the right arrow

button.

3. Highlight Park Heater and press the

right arrow button.

To prevent the battery from discharging:

104

Mondeo (CA2) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 31-12-2014, CG3536en enGBR, Edition date: 11/2013

Climate Control

1. Highlight Program 1 and press the right

arrow button.

2. Highlight the day on which the heater

should warm up the vehicle.

3. Press the OK button to confirm the

selection. A cross appears in the box

next to the day to show that this day is

selected.

4. Continue in the same way to select all

the days on which the heater should

warm up the vehicle.

5. To set the time at which the vehicle

should be warmed up, highlight the

time at the top of the display and press

the right arrow button.

•

The functions Program 1 and

Program 2 allow you to program up

to two heating cycles for each day of

the week. These times will remain

stored and the heater will warm up the

vehicle at these times on these days

every week.

The function One-Time allows you to

program one heating cycle for one

specific day.

6. Press the OK button and the hours

flash. Use the up and down arrow

buttons to adjust the individual settings

and the left and right arrow buttons to

move to the next or previous setting.

7. When you have finished, press the OK

button again to confirm the selection.

•

The function Active now

automatically switches on the heater.

Programming the functions Program 1

and Program 2

You can use the function Program 2 to set

a second cycle, for example different times

on different days or twice on the same day.

The programming procedure is the same

as for the function Program 1.

105

Mondeo (CA2) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 31-12-2014, CG3536en enGBR, Edition date: 11/2013

Climate Control

Programming the function One-Time

Starting

1. Highlight One-Time and press the right

Hold the transmitter with the antenna

upwards and press the ON button for at

least two seconds. The LED on the

transmitter lights up green to confirm the

signal has been received.

arrow button.

2. Press the OK button and the hours

flash. Use the up and down arrow

buttons to adjust the individual settings

and the left and right arrow buttons to

move to the next or previous setting.

Switching off

Hold the transmitter with the antenna

upwards and press the OFF button for at

least two seconds. The LED on the

transmitter lights up red to confirm the

signal has been received.

3. When you have finished, press the OK

button again to confirm the selection.

Active now

Highlight Active now and press the OK

button. A cross appears in the box next to

the function to show that the heater is

activated.

Remote start in combination with

direct start or timer

To deactivate the heater, highlight Active

now and press the OK button again.

Remote starting

The parking heater may be started and

switched off from a distance of up to 500

meters (1640 feet) using the supplied

remote control transmitter. This range will

vary depending upon local conditions and

terrain, as well as battery condition. The

remote control transmitter will indicate

whether or not the signal has been

Remote start is integrated with normal

heater control. Parking heaters started with

direct start or timer functions can be

switched off with the remote control

transmitter and vice versa.

received. The parking heater will operate

for a maximum of 30 minutes.

Note: The heater will operate, depending

on the ambient temperature, for between

10 and 30 minutes. The interior will cool

down after the heating period has elapsed,

therefore a remote start more than 30

minutes before driving is not recommended.

Note: The remote control may not always

receive confirmation of a successful remote

command at extended operating ranges.

Feedback during starting and

switching off

The LED on the transmitter illuminates

green for about two seconds. This

indicates the signal has been received by

the vehicle and the heater has started.

The LED on the transmitter illuminates red

for about two seconds. This indicates the

signal has been received by the vehicle and

the heater has switched off.

106

Mondeo (CA2) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 31-12-2014, CG3536en enGBR, Edition date: 11/2013

Climate Control

The LED on the transmitter flashes green

3. Install a new battery (3.3V type

or red for about two seconds. This

indicates the signal was not transmitted

correctly. Repeat the transmission.

CR1-3N) with the + facing upwards.

4. Re-assemble the remote control.

Programming the transmitter

The LED on the transmitter illuminates

orange for about two seconds before

showing green or red. This indicates the

transmitter batteries are weak and should

be changed.

Further transmitters may be used with the

remote system, please consult your dealer.

Up to a maximum of 3 separate remote

controls may be added. When adding extra

transmitters these must be programmed

separately.

The LED on the transmitter flashes orange

for about 5 seconds. This indicates that

the signal was not transmitted. The

Note: The heater must be switched off

transmitter batteries are discharged and

should be changed as soon as possible.

during programming.

Note: The programming procedure may be

repeated as often as is required. The oldest

programmed transmitter will be deleted

each time.

Changing the remote control

battery

Make sure that you dispose of old batteries

in an environmentally friendly way. Seek

advice from your local authority regarding

recycling.

1. Install the battery in the new

transmitter.

2. Turn off the power to the receiver by

removing fuse F32 from the engine

compartment fuse box. See Fuse

Specification Chart (page 159).

3. Wait for at least 5 seconds.

4. Reconnect power to the receiver by

replacing the fuse, and press the OFF

button on the new transmitter within

5 seconds until the LED light turns off.

5. The new transmitter is now

programmed.

Fuel operated heater (depending

on country)

1. Insert a screwdriver or other suitable

tool into the slot on the back of the

remote control, and unscrew the

compartment cover.

WARNING

The fuel operated heater must not

be operated at filling stations, near

sources of combustible vapors or

dust or in enclosed spaces.

CAUTION

Do not touch the battery contacts or

the printed circuit board with the

screwdriver.

2. Carefully prise out the battery.

107

Mondeo (CA2) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 31-12-2014, CG3536en enGBR, Edition date: 11/2013

Climate Control -> Auxiliary Heater for Your Ford Mondeo 4 Door Fifth Generation (2014-2022)

Related Topics

Popular Owner Manuals

Latest Owner Manuals