Driving your vehicle -> STARTING THE ENGINE for Your Hyundai I20 4 Door First Generation (2008-2014)

Driving your vehicle  
STARTING THE ENGINE  
E040000APB  
E040100AUN  
CAUTION  
Starting the gasoline engine  
If the engine stalls while the vehicle  
is in motion, do not attempt to move  
the shift lever to the P (Park) posi-  
tion. If traffic and road conditions  
permit, you may put the shift lever  
in the N (Neutral) position while the  
vehicle is still moving and turn the  
ignition switch to the START posi-  
tion in an attempt to restart the  
engine.  
WARNING  
1. Make sure the parking brake is  
applied.  
Always wear appropriate shoes  
when operating your vehicle.  
Unsuitable shoes (high heels, ski  
boots,etc.) may interfere with your  
ability to use the brake, accelerator  
pedal, and clutch (if equipped).  
2. Manual Transaxle - Depress the  
clutch pedal fully and shift the  
transaxle into Neutral. Keep the clutch  
pedal and brake pedal depressed  
while turning the ignition switch to the  
start position.  
Automatic Transaxle - Place the  
transaxle shift lever in P (Park).  
Depress the brake pedal fully.  
You can also start the engine when  
the shift lever is in the N (Neutral)  
position.  
CAUTION  
Do not engage the starter for more  
than 10 seconds. If the engine stalls  
or fails to start, wait 5 to 10 seconds  
before re-engaging the starter.  
Improper use of the starter may  
damage it.  
3. Turn the ignition switch to START and  
hold it there until the engine starts (a  
maximum of 10 seconds), then  
release the key.  
4. In extremely cold weather (below  
-18°C / 0°F) or after the vehicle has  
not been operated for several days, let  
the engine warm up without depress-  
ing the accelerator.  
Whether the engine is cold or warm, it  
should be started without depressing  
the accelerator.  
5 5  
Driving your vehicle  
E040101APB  
Starting and stopping the engine for tur-  
bocharger intercooler  
NOTICE  
Starting the diesel engine  
If the engine does not start within 10  
seconds after the preheating is complet-  
ed, turn the ignition key once more to  
the LOCK position for 10 seconds, and  
then to the ON position, in order to pre-  
heat again.  
1. Do not race or accelerate the engine  
immediately after starting it.  
To start the diesel engine when the  
engine is cold, it has to be pre-heated  
before starting the engine and then has  
to be warmed up before starting to drive.  
If the engine is cold, idle it for several  
seconds before sufficient lubrication is  
ensured in the turbocharger unit.  
1. Make sure the parking brake is  
applied.  
2. After high speed or extended driving,  
requiring a heavy engine load, idle the  
engine about 1 minute before turning it  
off.  
NOTICE - Kick down mechanism  
2. Depress the clutch pedal fully and shift  
the transaxle into Neutral. Keep the  
clutch pedal and brake pedal  
depressed while turning the ignition  
switch to the start position.  
If your vehicle is equipped with a kick  
down mechanism in an accelerator  
pedal,it prevents you from driving at  
full throttle unintentionally by making  
the driver require increased effort to  
depress the accelerator pedal. However  
if you depress the pedal more than  
approximately 80% the vehicle can be  
full throttle and the accelerator pedal  
will be easier to depress.This is not a  
malfunction but a normal condition.  
This idle time will allow the tur-  
bocharger to cool prior to shutting the  
engine off.  
3. Turn the ignition switch  
to the ON position to pre-  
heat the engine. Then  
CAUTION  
W-60  
the glow indicator light  
will illuminate.  
Do not turn the engine off immedi-  
ately after it has been subjected to  
a heavy load. Doing so may cause  
severe damage to the engine or  
turbo charger unit.  
4. If the glow indicator light goes out, turn  
the ignition switch to the START posi-  
tion and hold it there until the engine  
starts (a maximum of 10 seconds),  
then release the key.  
5 6