Get Driving your vehicle -> BRAKE SYSTEM Guide for Hyundai Ix35 SUV First Generation (2009-2015)

Driving your vehicle

BRAKE SYSTEM

Power brakes

In the event of brake failure

WARNING - Brakes

If service brakes fail to operate while the

vehicle is in motion, you can make an

emergency stop with the parking brake.

The stopping distance, however, will be

much greater than normal.

Your vehicle has power-assisted brakes

that adjust automatically through normal

usage.

• Do not drive with your foot rest-

ing on the brake pedal. This will

create abnormal high brake tem-

peratures, excessive brake lining

and pad wear, and increased

stopping distances.

In the event that the power-assisted

brakes lose power because of a stalled

engine or some other reason, you can

still stop your vehicle by applying greater

force to the brake pedal than you nor-

mally would. The stopping distance, how-

ever, will be longer.

WARNING - Parking brake

• When descending a long or steep

hill, shift to a lower gear and

avoid continuous application of

the brakes. Continuous brake

application will cause the brakes

to overheat and could result in a

temporary loss of braking per-

formance.

Applying the parking brake while

the vehicle is moving at normal

speeds can cause a sudden loss of

control of the vehicle. If you must

use the parking brake to stop the

vehicle, use great caution in apply-

ing the brake.

When the engine is not running, the

reserve brake power is partially depleted

each time the brake pedal is applied. Do

not pump the brake pedal when the

power assist has been interrupted.

• Wet brakes may impair the vehi-

cle’s ability to safely slow down;

the vehicle may also pull to one

side when the brakes are applied.

Applying the brakes lightly will

indicate whether they have been

affected in this way. Always test

your brakes in this fashion after

driving through deep water. To

dry the brakes, apply them lightly

while maintaining a safe forward

speed until brake performance

returns to normal.

Pump the brake pedal only when neces-

sary to maintain steering control on slip-

pery surfaces.

5 24

Driving your vehicle

Disc brakes wear indicator

Your vehicle has disc brakes.

CAUTION

• To avoid costly brake repairs, do

not continue to drive with worn

brake pads.

When your brake pads are worn and new

pads are required, you will hear a high-

pitched warning sound from your front

brakes or rear brakes. You may hear this

sound come and go or it may occur

whenever you depress the brake pedal.

• Always replace the front or rear

brake pads as pairs.

Please remember that some driving con-

ditions or climates may cause a brake

squeal when you first apply (or lightly

apply) the brakes. This is normal and

does not indicate a problem with your

brakes.

WARNING - Brake wear

This brake wear warning sound

means your vehicle needs service.

If you ignore this audible warning,

you will eventually lose braking

performance, which could lead to a

serious accident.

OLM059014

Parking brake

Applying the parking brake

■ Foot type

To engage the parking brake, first apply

the foot brake and then depress the park-

ing brake pedal down as far as possible.

5 25

Driving your vehicle

OLM059016

OLM059015

OLM059017

■ Hand type

Releasing the parking brake

■ Foot type

■ Hand type

To engage the parking brake, first apply

the foot brake and then pull up the park-

ing brake lever as far as possible.

To release the parking brake, first apply

the foot brake and pull up the parking

brake lever slightly. Secondly depress the

release button (1) and lower the parking

brake lever (2) while holding the button.

To release the parking brake, depress

the parking brake pedal a second time

while applying the foot brake. The pedal

will automatically extend to the fully

released position.

In addition it is recommended that when

parking the vehicle on an incline, the shift

lever should be in the P (Park) position

for Automatic transaxle, or Reverse for

manual transaxle.

CAUTION

Driving with the parking brake

applied will cause excessive brake

pad and brake rotor wear.

5 26

Driving your vehicle

If the parking brake does not release or

does not release all the way, have the

system checked by an authorized

HYUNDAI dealer.

Anti-lock brake system (ABS)

WARNING

ABS (or ESC) will not prevent acci-

dents due to improper or danger-

ous driving maneuvers. Even

though vehicle control is improved

during emergency braking, always

maintain a safe distance between

you and objects ahead. Vehicle

speeds should always be reduced

during extreme road conditions.

WARNING

• To prevent unintentional move-

ment when stopped and leaving

the vehicle, do not use the shift

lever in place of the parking

brake. Set the parking brake AND

make sure the shift lever is

securely positioned in P (Park).

W-75

The braking distance for vehicles

equipped with an anti-lock braking

system (or Electronic Stability

Control System) may be longer

than for those without it in the fol-

lowing road conditions.

Check the brake warning light by turning

the ignition switch ON (do not start the

engine). This light will be illuminated when

the parking brake is applied with the igni-

tion switch in the START or ON position.

• Never allow anyone who is unfa-

miliar with the vehicle to touch

the parking brake. If the parking

brake is released unintentionally,

serious injury may occur.

Before driving, be sure the parking brake

is fully released and the brake warning

light is off.

During these conditions the vehicle

should be driven at reduced

speeds:

• All vehicles should always have

the parking brake fully engaged

when parking to avoid inadver-

tent movement of the vehicle

which can injure occupants or

pedestrians.

If the brake warning light remains on after

the parking brake is released while the

engine is running, there may be a mal-

function in the brake system. Immediate

attention is necessary.

• Rough, gravel or snow-covered

roads.

• With tire chains installed.

(Continued)

If at all possible, cease driving the vehi-

cle immediately. If that is not possible,

use extreme caution while operating the

vehicle and only continue to drive the

vehicle until you can reach a safe loca-

tion or repair shop.

5 27

Driving your vehicle

The ABS continuously senses the speed

of the wheels. If the wheels are going to

lock, the ABS system repeatedly modu-

lates the hydraulic brake pressure to the

wheels.

✽

NOTICE

(Continued)

A click sound may be heard in the

engine compartment when the vehicle

begins to move after the engine is start-

ed. These conditions are normal and

indicate that the anti-lock brake system

is functioning properly.

• On roads where the road surface

is pitted or has different surface

height.

The safety features of an ABS (or

ESC) equipped vehicle should not

be tested by high speed driving or

cornering. This could endanger the

safety of yourself or others.

When you apply your brakes under con-

ditions which may lock the wheels, you

may hear a “tik-tik’’ sound from the

brakes, or feel a corresponding sensation

in the brake pedal. This is normal and it

means your ABS is active.

• Even with the anti-lock brake system,

your vehicle still requires sufficient

stopping distance. Always maintain a

safe distance from the vehicle in front

of you.

In order to obtain the maximum benefit

from your ABS in an emergency situa-

tion, do not attempt to modulate your

brake pressure and do not try to pump

your brakes. Press your brake pedal as

hard as possible or as hard as the situa-

tion allows the ABS to control the force

being delivered to the brakes.

• Always slow down when cornering.

The anti-lock brake system cannot pre-

vent accidents resulting from exces-

sive speeds.

• On loose or uneven road surfaces,

operation of the anti-lock brake system

may result in a longer stopping dis-

tance than for vehicles equipped with a

conventional brake system.

5 28

Driving your vehicle

CAUTION

• When you drive on a road having

poor traction, such as an icy road,

and have operated your brakes

continuously, the ABS will be

active continuously and the ABS

warning light may illuminate. Pull

your vehicle over to a safe place

and stop the engine.

• Restart the engine. If the ABS

warning light is off, then your

W-78

OLM059020L

ABS

system

is

normal.

Otherwise, you may have a prob-

lem with the ABS. Contact an

authorized HYUNDAI dealer as

soon as possible.

Electronic stability control (ESC)

CAUTION

The Electronic Stability control (ESC)

system is designed to stabilize the vehicle

during cornering maneuvers. ESC checks

where you are steering and where the

vehicle is actually going. ESC applies the

brakes at individual wheels and

intervenes in the engine management

system to stabilize the vehicle.

• If the ABS warning light is on and

stays on, you may have a problem

with the ABS. In this case, howev-

er, your regular brakes will work

normally.

✽

NOTICE

When you jump start your vehicle

because of a drained battery, the engine

may not run as smoothly and the ABS

warning light may turn on at the same

time. This happens because of the low

battery voltage. It does not mean your

ABS is malfunctioning.

• Do not pump your brakes!

• Have the battery recharged before

driving the vehicle.

• The ABS warning light will stay on

for approximately 3 seconds after

the ignition switch is ON. During

that time, the ABS will go through

self-diagnosis and the light will go

off if everything is normal. If the

light stays on, you may have a

problem with your ABS. Contact

an authorized HYUNDAI dealer as

soon as possible.

5 29

Driving your vehicle

The Electronic Stability Control (ESC)

system is an electronic system designed

to help the driver maintain vehicle control

under adverse conditions. It is not a

substitute for safe driving practices.

Factors including speed, road conditions

and driver steering input can all affect

whether ESC will be effective in

preventing a loss of control. It is still your

responsibility to drive and corner at

reasonable speeds and to leave a

sufficient margin of safety.

ESC operation

ESC ON condition

WARNING

Never drive too fast according to

the road conditions or too quickly

when cornering. Electronic stability

control (ESC) will not prevent acci-

dents. Excessive speed in turns,

abrupt maneuvers and hydroplan-

ing on wet surfaces can still result

in serious accidents. Only a safe

and attentive driver can prevent

accidents by avoiding maneuvers

that cause the vehicle to lose trac-

tion. Even with ESC installed,

always follow all the normal precau-

tions for driving - including driving

at safe speeds for the conditions.

• When the ignition is turned

ON, ESC and ESC OFF indi-

cator lights illuminate for

-

approximately

then ESC is turned on.

3

seconds,

• Press the ESC OFF button

for at least half a second after

turning the ignition ON to turn

ESC off. (ESC OFF indicator

will illuminate). To turn the

ESC on, press the ESC OFF

button (ESC OFF indicator

light will go off).

When you apply your brakes under con-

ditions which may lock the wheels, you

may hear a “tik-tik’’ sound from the

brakes, or feel a corresponding sensation

in the brake pedal. This is normal and it

means your ESC is active.

• When starting the engine,

you may hear a slight ticking

sound. This is the ESC per-

forming an automatic system

self-check and does not indi-

cate a problem.

✽

NOTICE

A click sound may be heard in the

engine compartment when the vehicle

begins to move after the engine is start-

ed. These conditions are normal and

indicate that the Electronic Stability

Control System is functioning properly.

5 30

Driving your vehicle

When operating

When the ESC is in operation,

the ESC indicator light blinks.

■ ESC indicator light

CAUTION

Driving with varying tire or wheel

sizes may cause the ESC system to

malfunction. When replacing tires,

make sure they are the same size as

your original tires.

• When the Electronic Stability

Control is operating properly,

you can feel a slight pulsation

in the vehicle. This is only the

effect of brake control and

indicates nothing unusual.

■ ESC OFF indicator light

Never operate the vehicle with dif-

ferent diameter tires installed at the

same time.

• When moving out of the mud

or driving on a slippery road,

pressing the accelerator

pedal may not cause the

engine rpm (revolutions per

minute) to increase.

Indicator light

WARNING

When ignition switch is turned to the ON

position, the indicator light illuminates,

then goes off if the ESC system is oper-

ating normally.

The Electronic Stability Control sys-

tem is only a driving aid; use pre-

cautions for safe driving by slowing

down on curved, snowy, or icy

roads. Drive slowly and don’t

attempt to accelerate whenever the

ESC indicator light is blinking, or

when the road surface is slippery.

The ESC indicator light blinks whenever

ESC is operating or illuminates when

ESC fails to operate.

ESC operation off

ESC OFF state

• To cancel ESC operation,

The ESC OFF indicator light comes on

when the ESC is turned off with the but-

ton.

press the ESC OFF button

(ESC OFF indicator light illu-

minates).

• If the ignition switch is turned

to LOCK position when ESC

is off, ESC remains off. Upon

restarting the engine, the

ESC will automatically turn

on again.

5 31

Driving your vehicle

ESC OFF usage

When driving

• ESC should be turned on for daily driv-

ing whenever possible.

VSM operation off

If you press the ESC OFF button to turn

off the ESC, the VSM will also cancel and

Vehicle stability management

(VSM) (if equipped)

This system provides further enhance-

ments to vehicle stability and steering

responses when a vehicle is driving on a

slippery road or a vehicle detected

changes in coefficient of friction between

right wheels and left wheels when brak-

ing.

the ESC OFF indicator light (

nates.

) illumi-

• To turn ESC off while driving, press the

ESC OFF button while driving on a flat

road surface.

To turn on the VSM, press the button

again. The ESC OFF indicator light goes

out.

WARNING

Malfunction indicator

Never press the ESC OFF button

while ESC is operating (ESC indica-

tor light blinks).

The VSM can be deactivated even if you

don’t cancel the VSM operation by press-

ing the ESC OFF button. It indicates that

a malfunction has been detected some-

where in the Electric Power Steering sys-

tem or VSM system. If the ESC indicator

VSM operation

When the VSM is in operation, ESC indi-

cator light (

) blinks.

If ESC is turned off while ESC is

operating, the vehicle may slip out

of control.

When the vehicle stability management

is operating properly, you can feel a slight

pulsation in the vehicle. This is only the

effect of brake control and indicates noth-

ing unusual.

light (

) or EPS warning light remains

on, take your vehicle to an authorized

HYUNDAI dealer and have the system

checked.

✽

NOTICE

• When operating the vehicle on a

dynamometer, ensure that the ESC is

turned off (ESC OFF light illuminat-

ed). If the ESC is left on, it may pre-

vent the vehicle speed from increas-

ing, and result in false diagnosis.

The VSM does not operate when:

• Driving on bank road such as gradient

or incline

• Driving rearward

✽

NOTICE

• The VSM is designed to function

above approximately 15 km/h (9 mph)

on curves.

• The VSM is designed to function

above approximately 30 km/h (18

mph) when a vehicle is braking on a

split-mu road. The split-mu road is

made of surfaces which have different

friction forces.

• ESC OFF indicator light (

on the instrument cluster

) remains

• Turning the ESC off does not affect

ABS or brake system operation.

• EPS indicator light remains on the

instrument cluster

5 32

Driving your vehicle

Hill-start assist control (HAC)

(if equipped)

WARNING

• The Vehicle Stability Management

system is not a substitute for

safe driving practices but a sup-

plementary function only. It is the

responsibility of the driver to

always check the speed and the

distance to the vehicle ahead.

Always hold the steering wheel

firmly while driving.

A vehicle has the tendency to slip back

on a steep hill when the driver begins to

accelerate after a stop. The Hill-start

Assist Control (HAC) prevents the vehi-

cle from slipping back by operating the

brakes automatically for about 2 sec-

onds. The brakes are released when the

accelerator pedal is depressed or after

about 2 seconds.

• Your vehicle is designed to acti-

vate according to the driver’s

intention, even with installed

VSM. Always follow all the normal

precautions for driving at safe

OLM059021L

WARNING

Downhill brake control (DBC)

(if equipped)

The HAC is activated only for about

2 seconds, so always depress the

accelerator pedal to begin acceler-

ating after a stop.

The Downhill Brake Control (DBC) helps

the driver descend steep hills and is acti-

vated at speeds less then 22 mph.

speeds for the conditions

–

including driving inclement

weather and on a slippery road.

DBC defaults to the OFF position when-

ever the ignition is turned on.

• Driving with varying tire or wheel

sizes may cause the VSM system

to malfunction. When replacing

tires, make sure they are the

same size as your original tires.

✽

NOTICE

The DBC can be turned on or off by

pushing the button.

• The HAC does not operate when the

transaxle shift lever is in the P (Park)

or N (Neutral) position.

• The HAC activates even though the

ESC is off but it does not activate

when the ESC has malfunctioned.

5 33

Driving your vehicle

✽

NOTICE

• The DBC does not turn ON in the P

(Park) position.

• The DBC may not activate if the ESC

(or BAS) is activated.

Mode

Indicator light

Description

Press the DBC button when the vehicle speed is under

25 mph (40 km/h). The DBC system will turn ON and

enter the standby mode.

Standby

The system does not turn ON if the vehicle speed is

over 25 mph (40 km/h).

• Noise or vibration may occur from the

brakes when the DBC is activated.

• The rear stop light comes on when the

DBC is activated.

• On a very steep hill even though the

brake pedal or accelerator pedal is

depressed the DBC may not deacti-

vate.

illuminated

In the standby mode, if the vehicle speed is under

22 mph (35 km/h) while driving down a steep hill, the

DBC will activate automatically.

Activated

blinks

• Always turn OFF the DBC on normal

roads. The DBC might activate from

the standby mode during abrupt

corning or driving over speed bumps.

• DBC may activate and cause the

engine to stop in vehicles with manual

transaxles if driving in 3rd gear (or

above) with DBC on. Do not turn on

DBC when driving in 3rd gear (or

above).

In the activated mode, the DBC will temporarily deacti-

vate under the following conditions:

• The hill is not steep enough.

Temporarily

deactivated

•

The brake pedal or accelerator pedal is depressed.

If the above conditions are gone, the DBC will automat-

ically activate again.

illuminated

The DBC will turn OFF under the following conditions:

• The DBC button is pressed again.

OFF

• The vehicle speed is over 38 mph (60 km/h).

not

illuminated

WARNING

If the DBC red indicator light illuminates, the system has overheated or there

is an operational problem. The DBC will not activate. If the DBC red indicator

light illuminates even though the DBC system has cooled, have the system

checked by an authorized HYUNDAI dealer.

5 34

Driving your vehicle

To dry the brakes, apply the brakes

lightly until the braking action returns to

normal, taking care to keep the vehicle

under control at all times. If the braking

action does not return to normal, stop

as soon as it is safe to do so and call an

authorized HYUNDAI dealer for assis-

tance.

• Be cautious when parking on a hill.

Firmly engage the parking brake and

place the shift lever in P (automatic

transaxle) or in first or reverse gear

(manual transaxle). If your vehicle is

facing downhill, turn the front wheels

into the curb to help keep the vehicle

from rolling. If your vehicle is facing

uphill, turn the front wheels away from

the curb to help keep the vehicle from

rolling. If there is no curb or if it is

required by other conditions to keep the

vehicle from rolling, block the wheels.

Good braking practices

WARNING

• Whenever you leave or park your

vehicle, always set the parking

brake as far as possible and fully

engage the vehicle's transaxle

into the P (Park) position or in

• Don't coast down hills with the vehicle

out of gear. This is extremely haz-

ardous. Keep the vehicle in gear at all

times, use the brakes to slow down,

then shift to a lower gear so that engine

braking will help you maintain a safe

speed.

first

or

reverse

(manual

transaxle). If the parking brake is

not fully engaged, the vehicle

may move inadvertently and

injure yourself and others.

• Under some conditions your parking

brake can freeze in the engaged posi-

tion.This is most likely to happen when

there is an accumulation of snow or ice

around or near the rear brakes or if the

brakes are wet. If there is a risk that the

parking brake may freeze, apply it only

temporarily while you put the shift lever

in P (automatic transaxle) or in first or

reverse gear (manual transaxle) and

block the rear wheels so the vehicle

cannot roll. Then release the parking

brake.

• All vehicles should always have

the parking brake fully engaged

when parking to avoid inadver-

tent movement of the vehicle

which can injure occupants or

pedestrians.

• Don't "ride" the brake pedal. Resting

your foot on the brake pedal while driv-

ing can be dangerous because the

brakes might overheat and lose their

effectiveness. It also increases the wear

of the brake components.

• Check to be sure the parking brake is

not engaged and that the parking brake

indicator light is out before driving

away.

• If a tire goes flat while you are driving,

apply the brakes gently and keep the

vehicle pointed straight ahead while you

slow down. When you are moving slow-

ly enough for it to be safe to do so, pull

off the road and stop in a safe place.

• Driving through water may get the

brakes wet.They can also get wet when

the vehicle is washed. Wet brakes can

be dangerous! Your vehicle will not stop

as quickly if the brakes are wet. Wet

brakes may cause the vehicle to pull to

one side.

• Do not hold the vehicle on the upgrade

with the accelerator pedal. This can

cause the transaxle to overheat.

Always use the brake pedal or parking

brake.

• If your vehicle is equipped with an auto-

matic transaxle, don't let your vehicle

creep forward. To avoid creeping for-

ward, keep your foot firmly on the brake

pedal when the vehicle is stopped.

5 35

Driving your vehicle -> BRAKE SYSTEM for Your Hyundai Ix35 SUV First Generation (2009-2015)

Related Topics

Popular Owner Manuals

Latest Owner Manuals