Get What to do in an emergency Guide for Hyundai Ix35 SUV First Generation (2009-2015)

Road warning / 6-2

In case of an emergency while driving / 6-2

If the engine will not start / 6-3

Emergency starting / 6-4

If the engine overheats / 6-6

Tire pressure monitoring system (TPMS) / 6-7

If you have a flat tire / 6-12

Towing / 6-20

What to do in an emergency

6

What to do in an emergency

IN CASE OF AN EMERGENCY

WHILE DRIVING

ROAD WARNING

It should be used whenever emergency

repairs are being made or when the vehi-

cle is stopped near the edge of a road-

way.

If the engine stalls at a crossroad

or crossing

If the engine stalls at a crossroad or

crossing, set the shift lever in the N

(Neutral) position and then push the vehi-

cle to a safe place.

Depress the flasher switch with the igni-

tion switch in any position. The flasher

switch is located in the center console

switch panel. All turn signal lights will

flash simultaneously.

If you have a flat tire while driving

If a tire goes flat while you are driving:

• The hazard warning flasher operates

whether your vehicle is running or not.

1.Take your foot off the accelerator pedal

and let the vehicle slow down while

driving straight ahead. Do not apply the

brakes immediately or attempt to pull

off the road as this may cause a loss of

control. When the vehicle has slowed

to such a speed that it is safe to do so,

brake carefully and pull off the road.

Drive off the road as far as possible

and park on firm, level ground. If you

are on a divided highway, do not park

in the median area between the two

traffic lanes.

OLM049084

• The turn signals do not work when the

hazard flasher is on.

Hazard warning flasher

• Care must be taken when using the

hazard warning flasher while the vehi-

cle is being towed.

The hazard warning flasher serves as a

warning to other drivers to exercise

extreme caution when approaching,

overtaking, or passing your vehicle.

6 2

What to do in an emergency

IF THE ENGINE WILL NOT START

2.When the vehicle is stopped, turn on

your emergency hazard flashers, set

the parking brake and put the transaxle

in P (automatic transaxle) or reverse

(manual transaxle).

If engine doesn't turn over or

turns over slowly

If engine turns over normally but

does not start

1. If your vehicle has an automatic

transaxle, be sure the shift lever is in N

(Neutral) or P (Park) and the emer-

gency brake is set.

1. Check fuel level.

2. With the ignition switch in the LOCK

position, check all connectors at igni-

tion coils and spark plugs. Reconnect

any that may be disconnected or

loose.

3.Have all passengers get out of the

vehicle. Be sure they all get out on the

side of the vehicle that is away from

traffic.

2. Check the battery connections to be

sure they are clean and tight.

3. Turn on the interior light. If the light

dims or goes out when you operate the

starter, the battery is discharged.

3. Check the fuel line in the engine com-

partment.

4.When changing a flat tire, follow the

instruction provided later in this sec-

tion.

4. If the engine still does not start, call an

authorized HYUNDAI dealer or seek

other qualified assistance.

4. Check the starter connections to be

sure they are securely tightened.

If engine stalls while driving

5. Do not push or pull the vehicle to start

it. See instructions for "Jump starting".

1. Reduce your speed gradually, keeping

a straight line. Move cautiously off the

road to a safe place.

WARNING

2. Turn on your emergency flashers.

If the engine will not start, do not

push or pull the vehicle to start it.

This could result in a collision or

cause other damage. In addition,

push or pull starting may cause the

catalytic converter to be over-

loaded and create a fire hazard.

3. Try to start the engine again. If your

vehicle will not start, contact an

authorized HYUNDAI dealer or seek

other qualified assistance.

6 3

What to do in an emergency

EMERGENCY STARTING

Jump starting

Jumper Cables

WARNING - Battery

Jump starting can be dangerous if done

incorrectly. Therefore, to avoid harm to

yourself or damage to your vehicle or

battery, follow the jump starting proce-

dures. If in doubt, we strongly recom-

mend that you have a competent techni-

cian or towing service jump start your

vehicle.

• Keep all flames or sparks away

from the battery. The battery pro-

duces hydrogen gas which may

explode if exposed to flame or

sparks.

(-)

(+)

(-)

If these instructions are not fol-

lowed exactly, serious personal

injury and damage to the vehicle

may occur! If you are not sure

how to follow this procedure,

(+)

Discharged

battery

Booster

battery

CAUTION

1VQA4001

Use only a 12-volt jumper system.

You can damage a 12-volt starting

motor, ignition system, and other

electrical parts beyond repair by

use of a 24-volt power supply (either

two 12-volt batteries in series or a

24-volt motor generator set).

seek

qualified

assistance.

Automobile batteries contain sul-

furic acid. This is poisonous and

highly corrosive. When jump

starting, wear protective glasses

and be careful not to get acid on

yourself, your clothing or on the

vehicle.

Connect cables in numerical order and

disconnect in reverse order.

• Do not attempt to jump start the

vehicle if the discharged battery

is frozen or if the electrolyte level

is low; the battery may rupture or

explode.

WARNING - Battery

Never attempt to check the elec-

trolyte level of the battery as this

may cause the battery to rupture or

explode causing serious injury.

6 4

What to do in an emergency

Jump starting procedure

Do not allow the jumper cables to con-

tact anything except the correct battery

terminals or the correct ground. Do not

lean over the battery when making

connections.

Push-starting

1. Make sure the booster battery is 12-

volt and that its negative terminal is

grounded.

Your manual transaxle-equipped vehicle

should not be push-started because it

might damage the emission control sys-

tem.

2. If the booster battery is in another

vehicle, do not allow the vehicles to

touch.

Vehicles equipped with automatic

transaxle cannot be push-started.

CAUTION - Battery cables

3. Turn off all unnecessary electrical

loads.

Follow the directions in this section for

jump-starting.

Do not connect the jumper cable

from the negative terminal of the

booster battery to the negative ter-

minal of the discharged battery.

This can cause the discharged bat-

tery to overheat and crack, releas-

ing battery acid.

4. Connect the jumper cables in the exact

sequence shown in the illustration.

First connect one end of a jumper

cable to the positive terminal of the

discharged battery (1), then connect

the other end to the positive terminal

on the booster battery (2).

WARNING

Never tow a vehicle to start it

because the sudden surge forward

when the engine starts could cause

a collision with the tow vehicle.

Proceed to connect one end of the

other jumper cable to the negative ter-

minal of the booster battery (3), then

the other end to a solid, stationary,

metallic point (for example, the engine

lifting bracket) away from the battery

(4). Do not connect it to or near any

part that moves when the engine is

cranked.

5. Start the engine of the vehicle with the

booster battery and let it run at 2,000

rpm, then start the engine of the vehi-

cle with the discharged battery.

If the cause of your battery discharging is

not apparent, you should have your vehi-

cle checked by an authorized HYUNDAI

dealer.

6 5

What to do in an emergency

IF THE ENGINE OVERHEATS

If your temperature gauge indicates over-

heating, you experience a loss of power,

or hear loud pinging or knocking, the

engine is probably too hot. If this hap-

pens, you should:

4. Check to see if the water pump drive

belt is missing. If it is not missing,

check to see that it is tight. If the drive

belt seems to be satisfactory, check for

coolant leaking from the radiator,

hoses or under the vehicle. (If the air

conditioning had been in use, it is nor-

mal for cold water to be draining from

it when you stop).

6.If you cannot find the cause of the

overheating, wait until the engine tem-

perature has returned to normal. Then,

if coolant has been lost, carefully add

coolant to the reservoir to bring the

fluid level in the reservoir up to the

halfway mark.

1. Pull off the road and stop as soon as it

is safe to do so.

2. Place the shift lever in P (automatic

transaxle) or neutral (manual transaxle)

and set the parking brake. If the air con-

ditioning is on, turn it off.

3. If engine coolant is running out under

the vehicle or steam is coming out

from the hood, stop the engine. Do not

open the hood until the coolant has

stopped running or the steaming has

stopped. If there is no visible loss of

engine coolant and no steam, leave

the engine running and check to be

sure the engine cooling fan is operat-

ing. If the fan is not running, turn the

engine off.

7.Proceed with caution, keeping alert for

further signs of overheating. If over-

heating happens again, call an author-

ized HYUNDAI dealer for assistance.

WARNING

While the engine is running, keep

hair, hands and clothing away from

moving parts such as the fan and

drive belts to prevent injury.

CAUTION

Serious loss of coolant indicates

there is a leak in the cooling system

and this should be checked as soon

as possible by an authorized

HYUNDAI dealer.

5. If the water pump drive belt is broken

or engine coolant is leaking out, stop

the engine immediately and call the

nearest authorized HYUNDAI dealer

for assistance.

WARNING

Do not remove the radiator cap

when the engine is hot. This can

allow coolant to be blown out of the

opening and cause serious burns.

6 6

What to do in an emergency

TIRE PRESSURE MONITORING SYSTEM (TPMS)

As an added safety feature, your Your vehicle has also been equipped

vehicle has been equipped with a tire with a TPMS malfunction indicator to

pressure monitoring system (TPMS) indicate when the system is not

that illuminates a low tire pressure operating properly. The TPMS mal-

telltale when one or more of your function indicator is combined with

tires is significantly under-inflated. the low tire pressure telltale. When

Accordingly, when the low tire pres- the system detects a malfunction,

sure telltale illuminates, you should the telltale will flash for approximate-

stop and check your tires as soon as ly one minute and then remain con-

possible, and inflate them to the tinuously illuminated. This sequence

proper pressure. Driving on a signifi- will continue upon subsequent vehi-

cantly under-inflated tire causes the cle start-ups as long as the malfunc-

tire to overheat and can lead to tire tion exists. When the malfunction

failure. Under-inflation also reduces indicator is illuminated, the system

fuel efficiency and tire tread life, and may not be able to detect or signal

may affect the vehicle’s handling and low tire pressure as intended. TPMS

OLM069012

(1) Low tire pressure telltale /

TPMS malfunction indicator

stopping ability.

malfunctions may occur for a variety

of reasons, including the installation

of replacement or alternate tires or

wheels on the vehicle that prevent

the TPMS from functioning properly.

Always check the TPMS malfunction

telltale after replacing one or more

tires or wheels on your vehicle to

ensure that the replacement or alter-

nate tires and wheels allow the

TPMS to continue to function proper-

ly.

Each tire, including the spare (if pro-

vided), should be checked monthly

when cold and inflated to the inflation

pressure recommended by the vehi-

cle manufacturer on the vehicle plac-

ard or tire inflation pressure label. (If

your vehicle has tires of a different

size than the size indicated on the

vehicle placard or tire inflation pres-

sure label, you should determine the

proper tire inflation pressure for

those tires.)

Please note that the TPMS is not a

substitute for proper tire mainte-

nance, and it is the driver’s responsi-

bility to maintain correct tire pres-

sure, even if under-inflation has not

reached the level to trigger illumina-

tion of the TPMS low tire pressure

telltale.

6 7

What to do in an emergency

Low tire pressure tell-

tale

✽

NOTICE

The compact spare tire is not

equipped with a tire pressure sensor.

If the TPMS, Low Tire Pressure indi-

cator does not illuminate for 3 sec-

onds when the ignition switch is

turned to the ON position or the

engine is running, or if it remains

illuminated after coming on for

approximately 3 seconds, take your

vehicle to your nearest authorized

HYUNDAI dealer and have the sys-

tem checked.

When the tire pressure monitoring

system warning indicator is illuminat-

ed, one or more of your tires is sig-

nificantly under-inflated.

Immediately reduce your speed,

avoid hard cornering and anticipate

increased stopping distances. You

should stop and check your tires as

soon as possible. Inflate the tires to

the proper pressure as indicated on

the vehicle’s placard or tire inflation

pressure label located on the driver’s

side center pillar outer panel. If you

cannot reach a service station or if

the tire cannot hold the newly added

air, replace the low pressure tire with

the compact spare tire.

Then the TPMS malfunction indicator

may turn on and the Low Tire

Pressure telltale will remain on until

you have the low-pressure tire

repaired and replaced on the vehicle.

6 8

What to do in an emergency

TPMS (Tire Pressure

Monitoring System)

malfunction indicator

CAUTION

WARNING - Low pressure

damage

In winter or cold weather, the

low tire pressure telltale may be

illuminated if the tire pressure

was adjusted to the recom-

mended tire inflation pressure

in warm weather. It does not

mean yourTPMS is malfunction-

ing because the decreased tem-

perature leads to a proportional

lowering of tire pressure.

Significantly low tire pressure

makes the vehicle unstable and

can contribute to loss of vehicle

control and increased braking

distances.

The low tire pressure telltale will illu-

minate after it blinks for approximate-

ly one minute when there is a prob-

lem with the Tire Pressure

Monitoring system.

Continued driving on low pres-

sure tires can cause the tires to

overheat and fail.

Have the system checked by an

authorized HYUNDAI dealer as soon

as possible to determine the cause

of the problem.

When you drive your vehicle

from a warm area to a cold area

or from a cold area to a warm

area, or the outside temperature

is greatly higher or lower, you

should check the tire inflation

pressure and adjust the tires to

the recommended tire inflation

pressure.

6 9

What to do in an emergency

Changing a tire with TPMS

After you replace the low pressure

tire with the compact spare tire, the

TPMS malfunction indicator may be

illuminated after a few minutes

because the compact spare tire does

not have a sensor.

CAUTION

If you have a flat tire, the Low Tire

Pressure warning indicator will turn

on. Have the flat tire repaired by an

authorized HYUNDAI dealer as soon

as possible or replace the flat tire

with the compact spare tire.

• The TPMS malfunction indica-

tor may be illuminated if the

vehicle is moving around elec-

tric power supply cables or

radios transmitter such as at

police stations, government

and public offices, broadcast-

ing stations, military installa-

tions, airports, or transmitting

towers, etc. This can interfere

with normal operation of the

Tire Pressure Monitoring

System (TPMS).

Once the low pressure tire is re-

inflated to the recommended pres-

sure and installed on the vehicle, the

TPMS malfunction indicator and the

low tire pressure telltale will extin-

guish within a few minutes.

CAUTION

NEVER use a puncture-repair-

ing agent to repair and/or inflate

a low pressure tire. The tire

sealant can damage the tire

pressure sensor. If used, you

will have to replace the tire pres-

sure sensor.

If the indicators do not extinguish

after a few minutes, please visit an

authorized HYUNDAI dealer.

• The TPMS malfunction indica-

tor may be illuminated if snow

chains are used or some sep-

arate electronic devices such

as notebook computer, mobile

charger, remote starter or nav-

igation etc., are used in the

vehicle.This can interfere with

normal operation of the Tire

Pressure Monitoring System

(TPMS).

You may not be able identify a low

tire by simply looking at it. Always

use a good quality tire pressure

gauge to measure the tire's inflation

pressure. Please note that a tire that

is hot (from being driven) will have a

higher pressure measurement than a

tire that is cold (from sitting station-

ary for at least 3 hours and driven

less than 1 mile (1.6 km) during that

3 hour period).

Each wheel is equipped with a tire

pressure sensor mounted inside the

tire behind the valve stem. You must

use TPMS specific wheels. It is rec-

ommended that you always have

your tires serviced by an authorized

HYUNDAI dealer.

Even if you replace the low pressure

tire with the compact spare tire, the

Low Tire Pressure warning indicator

will remain on until the low pressure

tire is repaired and placed on the

vehicle.

6 10

What to do in an emergency

Allow the tire to cool before measur-

ing the inflation pressure. Always be

sure the tire is cold before inflating to

the recommended pressure.

This device complies with Part 15

of the FCC rules.

WARNING - TPMS

• The TPMS cannot alert you to

severe and sudden tire dam-

age caused by external fac-

tors such as nails or road

debris.

Operation is subject to the following

two conditions:

A cold tire means the vehicle has

been sitting for 3 hours and driven for

less than 1 mile (1.6 km) in that 3

hour period.

1. This device may not cause harm-

ful interference, and

2. This device must accept any inter-

ference received, including inter-

ference that may cause undesired

operation.

• If you feel any vehicle instabil-

ity, immediately take your foot

off the accelerator, apply the

brakes gradually and with

light force, and slowly move to

a safe position off the road.

CAUTION

Do not use any tire sealant if

your vehicle is equipped with a

WARNING

Tire

Pressure

Monitoring

Changes or modifications not

expressly approved by the party

responsible for compliance

could void the user's authority

to operate the equipment.

System. The liquid sealant can

damage the tire pressure sen-

sors.

WARNING - Protecting

TPMS

Tampering with, modifying, or

disabling the Tire Pressure

Monitoring System (TPMS)

components may interfere with

the system's ability to warn the

driver of low tire pressure con-

ditions and/or TPMS malfunc-

tions. Tampering with, modify-

ing, or disabling the Tire

Pressure Monitoring System

(TPMS) components may void

the warranty for that portion of

the vehicle.

6 11

What to do in an emergency

IF YOU HAVE A FLAT TIRE

Jacking instructions

(1) Jack handle

(2) Jack

The jack is provided for emergency

tire changing only.

(3) Wheel lug nut wrench

To prevent the jack from “rattling”

while the vehicle is in motion, store it

properly.

Follow jacking instructions to reduce

the possibility of personal injury.

WARNING - Changing tires

• Never attempt vehicle repairs

in the traffic lanes of a public

road or highway.

OLM069001

Jack and tools

The jack, jack handle, wheel lug nut

wrench are stored in the luggage

compartment. Pull up the luggage

box cover to reach this equipment.

• Always move the vehicle com-

pletely off the road and onto

the shoulder before trying to

change a tire. The jack should

be used on level firm level

ground. If you cannot find a

firm, level place off the road,

call a towing service company

for assistance.

(Continued)

6 12

What to do in an emergency

(Continued)

• Be sure to use the correct

front and rear jacking posi-

tions on the vehicle; never

use the bumpers or any other

part of the vehicle for jack

support.

• The vehicle can easily roll off

the jack causing serious

injury or death. No person

should place any portion of

their body under a vehicle that

is supported only by a jack;

use vehicle support stands.

OLM069002

1VQA4022

Removing and storing the spare

tire

Changing tires

1. Park on a level surface and apply

the parking brake firmly.

Remove the luggage floor support

(1).

• Do not start or run the engine

while the vehicle is on the

jack.

2. Place the transaxle shift lever in R

(Reverse) with manual transaxle or

P (Park) with automatic transaxle.

Turn the tire hold-down wing bolt (2)

counterclockwise.

• Do not allow anyone to remain

in the vehicle while it is on the

jack.

Store the tire in the reverse order of 3. Activate the hazard warning flash-

removal.

er.

Replace the luggage floor support

(1) after tightening the wing bolt.

• Make sure any children pres-

ent are in a secure place away

from the road and from the

vehicle to be raised with the

jack.

To prevent the spare tire and tools

from “rattling” while the vehicle is in

motion, store them properly.

6 13

What to do in an emergency

WARNING - Changing a tire

• To prevent vehicle movement

while changing a tire, always

set the parking brake fully,

and always block the wheel

diagonally opposite the wheel

being changed.

• We recommend that the

wheels of the vehicle be

blocked, and that no person

remain in a vehicle that is

being jacked.

1VQA4023

OLM069006

4. Remove the wheel lug nut wrench,

jack, jack handle, and spare tire

from the vehicle.

6. Loosen the wheel lug nuts coun-

terclockwise one turn each, but do

not remove any nut until the tire

has been raised off the ground.

5. Block both the front and rear of the

wheel that is diagonally opposite

the jack position.

6 14

What to do in an emergency

9. Loosen the wheel nuts and

remove them with your fingers.

Slide the wheel off the studs and

lay it flat so it cannot roll away. To

put the wheel on the hub, pick up

the spare tire, line up the holes

with the studs and slide the wheel

onto them. If this is difficult, tip the

wheel slightly and get the top hole

in the wheel lined up with the top

stud. Then jiggle the wheel back

and forth until the wheel can be

slid over the other studs.

OCM049013N

OCM054012

7. Place the jack at the front or rear 8. Insert the jack handle into the jack

jacking position closest to the tire

you are changing. Place the jack

at the designated locations under

the frame.

and turn it clockwise, raising the

vehicle until the tire just clears the

ground. This measurement is

approximately 1.2 in (30 mm).

Before removing the wheel lug

nuts, make sure the vehicle is sta-

ble and that there is no chance for

movement or slippage.

WARNING - Jack location

To reduce the possibility of

injury, be sure to use only the

jack provided with the vehicle

and in the correct jack position;

never use any other part of the

vehicle for jack support.

6 15

What to do in an emergency

10. To reinstall the wheel, hold it on

the studs, put the wheel nuts on

the studs and tighten them finger

tight. Jiggle the tire to be sure it is

completely seated, then tighten

the nuts as much as possible

with your fingers again.

WARNING

Wheels may have sharp edges.

Handle them carefully to avoid

possible severe injury. Before

putting the wheel into place, be

sure that there is nothing on the

hub or wheel (such as mud, tar,

gravel, etc.) that prevents with

the wheel from fitting solidly

against the hub.

11. Lower the vehicle to the ground

by turning the wheel nut wrench

counterclockwise.

OLM069007

If there is, remove it. If contact of

the mounting surface between

the wheel and hub is not good,

the wheel nuts could come

loose and cause the loss of a

wheel. Loss of a wheel may

result in loss of control of the

vehicle. This may cause serious

injury or death.

Then position the wrench as shown in

the drawing and tighten the wheel

nuts. Be sure the socket is seated

completely over the nut. Do not stand

on the wrench handle or use an exten-

sion pipe over the wrench handle. Go

around the wheel tightening every nut

following the numerical sequence

shown in the image until they are all

tight. Then double-check each nut for

tightness. After changing wheels, have

an authorized HYUNDAI dealer tight-

en the wheel nuts to their proper

torque as soon as possible.

Wheel nut tightening torque:

Steel wheel & aluminum alloy wheel:

65~79 lb·ft (9~11 kg·m)

6 16

What to do in an emergency

If you have a tire gauge, remove the

valve cap and check the air pressure.

If the pressure is lower than recom-

mended, drive slowly to the nearest

service station and inflate to the cor-

rect pressure. If it is too high, adjust

it until it is correct. Always reinstall

the valve cap after checking or

adjusting tire pressure. If the cap is

not replaced, dust and dirt may get

into the tire valve and air may leak

from the tire. If you lose a valve cap,

buy another and install it as soon as

possible.

CAUTION

WARNING - Wheel studs

If the studs are damaged, they

may lose their ability to retain

the wheel.This could lead to the

loss of the wheel and a collision

resulting in serious injuries.

Your vehicle has metric threads

on the wheel studs and nuts.

Make certain during wheel

removal that the same nuts that

were removed are reinstalled -

or, if replaced, that nuts with

metric threads and the same

chamfer configuration are used.

Installation of a non-metric

thread nut on a metric stud or

vice-versa will not secure the

wheel to the hub properly and

will damage the stud so that it

must be replaced.

To prevent the jack, jack handle,

wheel lug nut wrench and spare tire

from rattling while the vehicle is in

motion, store them properly.

After you have changed wheels,

always secure the flat tire in its place

and return the jack and tools to their

proper storage locations.

WARNING - Inadequate

spare tire pressure

Note that most lug nuts do not

have metric threads. Be sure to

use extreme care in checking

for thread style before installing

aftermarket lug nuts or wheels.

If in doubt, consult an author-

ized HYUNDAI dealer.

Check the inflation pressures as

soon as possible after installing

the spare tire. Adjust it to the

specified pressure, if necessary.

Refer to “Tires and wheels” sec-

tion 8.

6 17

What to do in an emergency

Important - use of compact spare tire

Your vehicle is equipped with a com-

pact spare tire. This compact spare

tire takes up less space than a regu-

lar-size tire.This tire is smaller than a

conventional tire and is designed for

temporary use only.

When using a compact spare tire,

observe the following precautions:

WARNING

The compact spare tire is for

emergency use only. Do not

operate your vehicle on this

compact spare at speeds over

50 mph (80 km/h). The original

tire should be repaired or

replaced as soon as is possible

to avoid failure of the spare

possibly leading to personal

injury or death.

• Under no circumstances should

you exceed 50 mph (80 km/h); a

higher speed could damage the

tire.

• Ensure that you drive slowly

enough for the road conditions to

avoid all hazards. Any road hazard,

such as a pothole or debris, could

seriously damage the compact

spare.

CAUTION

• You should drive carefully

when the compact spare is in

use. The compact spare

should be replaced by the

proper conventional tire and

rim at the first opportunity.

• Any continuous road use of this tire

could result in tire failure, loss of

vehicle control, and possible per-

sonal injury.

The compact spare should be inflat-

ed to 60 psi (420 kPa).

• The operation of this vehicle

is not recommended with

more than one compact spare

tire in use at the same time.

• Do not exceed the vehicle’s maxi-

mum load rating or the load-carry-

ing capacity shown on the sidewall

of the compact spare tire.

✽

NOTICE

Check the inflation pressure after

installing the spare tire. Adjust it to

the specified pressure, as necessary.

• Avoid driving over obstacles. The

compact spare tire diameter is

smaller than the diameter of a con-

ventional tire and reduces the

ground clearance approximately 1

inch (25 mm), which could result in

damage to the vehicle.

6 18

What to do in an emergency

• Do not take this vehicle through an • The compact spare tire should not

automatic car wash while the com-

pact spare tire is installed.

be used on any other wheels, nor

should standard tires, snow tires,

wheel covers or trim rings be used

with the compact spare wheel. If

such use is attempted, damage to

these items or other car compo-

nents may occur.

• Do not use tire chains on the com-

pact spare tire. Because of the

smaller size, a tire chain will not fit

properly. This could damage the

vehicle and result in loss of the

chain.

• Do not use more than one compact

spare tire at a time.

• The compact spare tire should not

be installed on the front axle if the • Do not tow a trailer while the com-

vehicle must be driven in snow or

on ice.

pact spare tire is installed.

• Do not use the compact spare tire

on any other vehicle because this

tire has been designed especially

for your vehicle.

CAUTION

When the original tire and wheel

are repaired and reinstalled on

the vehicle, the wheel nut torque

must be set correctly to prevent

wheel vibration. The correct

wheel nut tightening torque is

65~79lb-ft (9~11kg.m).

• The compact spare tire’s tread life

is shorter than a regular tire.

Inspect your compact spare tire

regularly and replace worn com-

pact spare tires with the same size

and design, mounted on the same

wheel.

6 19

What to do in an emergency

TOWING

On AWD vehicles, your vehicle must be

towed with a wheel lift and dollies or

flatbed equipment with all the wheels off

the ground.

CAUTION

The AWD vehicle should never be

towed with the wheels on the

ground. This can cause serious

damage to the transaxle or the AWD

system.

OUN046030

dolly

On 2WD vehicles, it is acceptable to tow

the vehicle with the rear wheels on the

ground (without dollies) and the front

wheels off the ground.

If any of the loaded wheels or suspen-

sion components are damaged or the

vehicle is being towed with the front

wheels on the ground, use a towing dolly

under the front wheels.

dolly

OXM069028

OUN046029

Towing service

If emergency towing is necessary, we

recommend having it done by an author-

ized HYUNDAI dealer or a commercial

tow-truck service. Proper lifting and tow-

ing procedures are necessary to prevent

damage to the vehicle. The use of wheel

dollies or flatbed is recommended.

When being towed by a commercial tow

truck and wheel dollies are not used, the

front of the vehicle should always be lift-

ed, not the rear.

CAUTION

• Do not tow the vehicle backwards

with the front wheels on the

ground as this may cause dam-

age to the vehicle.

• Do not tow with sling-type equip-

ment. Use wheel lift or flatbed

equipment.

For trailer towing guidelines information,

refer to “Trailer towing” in section 5.

6 20

What to do in an emergency

■ Front

When towing your vehicle in an emer-

gency without wheel dollies :

1. Set the ignition switch in the ACC posi-

tion.

2. Place the transaxle shift lever in N

(Neutral).

3. Release the parking brake.

CAUTION

OLM069014

Failure to place the transaxle shift

lever in N (Neutral) may cause inter-

nal damage to the transaxle.

■ Rear

OLM069016L

Removable towing hook (rear)

1. Open the tailgate, and remove the tow-

ing hook from the tool case.

2. Remove the hole cover pressing the

lower part of the cover on the rear

bumper.

3. Install the towing hook by turning it

clockwise into the hole until it is fully

secured.

OLM069015

Emergency towing

4. Remove the towing hook and install

the cover after use.

If towing is necessary, we recommend

you to have it done by an authorized

HYUNDAI dealer or a commercial tow

truck service.

6 21

What to do in an emergency

If towing service is not available in an

emergency, your vehicle may be tem-

porarily towed using a cable or chain

secured to the emergency towing hook

under the front (or rear) of the vehicle.

Use extreme caution when towing the

vehicle. A driver must be in the vehicle to

steer it and operate the brakes.

CAUTION

• Attach a towing strap to the tow

hook.

WARNING

Use extreme caution when towing

the vehicle.

• Using a portion of the vehicle

other than the tow hooks for tow-

ing may damage the body of your

vehicle.

• Avoid sudden starts or erratic

driving maneuvers which would

place excessive stress on the

emergency towing hook and tow-

ing cable or chain. The hook and

towing cable or chain may break

and cause serious injury or dam-

age.

Towing in this manner may be done only

on hard-surfaced roads for a short dis-

tance and at low speeds. Also, the

wheels, axles, power train, steering and

brakes must all be in good condition.

• Use only a cable or chain specifi-

cally intended for use in towing

vehicles. Securely fasten the

cable or chain to the towing hook

provided.

• If the disabled vehicle is cannot

be moved, do not forcibly contin-

ue the towing. Contact an author-

ized HYUNDAI dealer or a com-

mercial tow truck service for

assistance.

• Do not use the tow hooks to pull a vehi-

cle out of mud, sand or other condi-

tions from which the vehicle cannot be

driven out under its own power.

• Before emergency towing, check that

the hook is not broken or damaged.

• Avoid towing a vehicle heavier than the

vehicle doing the towing.

• The drivers of both vehicles should

communicate with each other frequent-

ly.

• Fasten the towing cable or chain

securely to the hook.

• Tow the vehicle as straight ahead

as possible.

• Do not jerk the hook. Apply steady and

even force.

• Keep away from the vehicle dur-

ing towing.

• To avoid damaging the hook, do not

pull from the side or at a vertical angle.

Always pull straight ahead.

6 22

What to do in an emergency

Emergency towing precautions

• Turn the ignition switch to ACC so the

steering wheel isn’t locked.

CAUTION - Automatic

transaxle

• If the car is being towed with all

four wheels on the ground, it can

be towed only from the front. Be

sure that the transaxle is in neu-

tral. Be sure the steering is

unlocked by placing the ignition

switch in the ACC position. A

driver must be in the towed vehi-

cle to operate the steering and

brakes.

• Place the transaxle shift lever in N

(Neutral).

• Release the parking bake.

• Press the brake pedal with more force

than normal since you will have

reduced brake performance.

• More steering effort will be required

because the power steering system

will be disabled.

OEN066014

• If you are driving down a long hill, the

brakes may overheat and brake per-

formance will be reduced. Stop often

and let the brakes cool off.

• To avoid serious damage to the

automatic transaxle, limit the

vehicle speed to 15 km/h (10 mph)

and drive less than 1.5 km (1

mile) when towing.

• Use a towing strap less than 16 feet (5

m) long. Attach a white or red cloth

(about 12 inches (30 cm) wide) in the

middle of the strap for easy visibility.

• Drive carefully so that the towing strap

is not loosened during towing.

• Before towing, check the auto-

matic transaxle for fluid leaks

under your vehicle. If the auto-

matic transaxle fluid is leaking,

flatbed equipment or a towing

dolly must be used.

6 23

What to do in an emergency

WARNING

• Do not use the hooks under the

front (or rear) of the vehicle for

towing purposes. These hooks

are designed ONLY for transport

tie-down. If the tie-down hooks

are used for towing, the tie-down

hooks or front (or rear) bumper

will be damaged and this could

lead to serious injury.

• The hooks should be placed

toward the front of the vehicle

when using the front holes and

should be placed toward the rear

of the vehicle when using the rear

holes for tie down purpose.

OLM069017N

Tie-down hook

(for flatbed towing) (if equipped)

If not, the front or rear under

cover will be damaged.

6 24

What to do in an emergency for Your Hyundai Ix35 SUV First Generation (2009-2015)

Related Topics

Popular Owner Manuals

Latest Owner Manuals