2023-2026 Hyundai Kona SUV Emergency Situations User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Emergency Situations for Your Hyundai Kona SUV Second Generation (2023-2026)

8. Emergency Situations  
Hazard Warning Flasher  
2C_HazardWarningLamp  
The hazard warning flasher warns other drivers to exercise extreme caution when  
approaching, overtaking, or passing your vehicle.  
It should be used whenever making emergency repairs or when stopped near the edge of  
a roadway.  
To turn on or off the hazard warning flasher, press the hazard warning flasher button with  
the Engine Start/Stop button in any position. The hazard warning flasher button is located  
in the center fascia panel. All turn signal lights flash simultaneously.  
• The hazard warning flasher operates regardless of whether your vehicle is running or  
not.  
• The turn signals do not work when the hazard flasher is on.  
Emergency Situations 583  
In Case Of An Emergency While Driving  
If the engine stalls while driving  
• Reduce the vehicle speed gradually, keeping a straight line. Move cautiously off the  
road to a safe place.  
• Turn on your hazard warning flasher.  
• Try to start the engine again. If your vehicle does not start, contact an authorized  
HYUNDAI dealer.  
If the engine stalls at a crossroad or crossing  
If the engine stalls at a crossroads or crossing, if safe to do so, shift the gear to N (Neutral)  
and then push the vehicle to a safe location.  
To stay N (Neutral) while the vehicle is off, refer to the "To stay in N (Neutral) when vehicle  
is OFF" section in chapter 6.  
If you have a flat tire while driving  
If a tire goes flat while you are driving:  
• Take your foot off the accelerator pedal and let the vehicle slow down while driving  
straight ahead. Do not apply the brakes immediately or attempt to pull off the road  
because this may cause loss of vehicle control resulting in a collision. When the vehicle  
has slowed to such a speed that it is safe to do so, brake carefully and pull off the road.  
Drive off the road as far as possible and park on a firm, level ground. If you are on a  
divided highway, do not park in the median area between the two traffic lanes.  
• When the vehicle is stopped, press the hazard warning flasher button, shift the gear to  
P (Park), apply the parking brake, and press the Engine Start/Stop button OFF position.  
• Have all passengers get out of the vehicle. Make sure they all get out on the side of the  
vehicle that is away from traffic.  
• When changing or inflating a flat tire, follow the instructions provided later in this  
chapter.  
584 Emergency Situations  
If The Engine Does Not Start  
• Be sure the gear to N (Neutral) or P (Park). The engine starts only when the gear is in N  
(Neutral) or P (Park).  
• Turn on the interior light. If the light dims or goes out when you operate the starter, the  
battery is drained.  
Refer to the instructions in the “Jump starting” section in this chapter.  
• Check the fuel level and add fuel if necessary.  
If the vehicle still does not start, contact for assistance.  
NOTICE  
Starting the vehicle by pushing or pulling may cause the catalytic converter to overload  
and damage the emission control system.  
Emergency Situations 585  
Jump Starting  
Jump starting can be dangerous if done incorrectly. Follow the jump starting procedure  
in this section to avoid serious injury or damage to your vehicle. If in doubt about how to  
properly jump start your vehicle, have a service technician or towing service do it for you.  
586 Emergency Situations  
WARNING  
To prevent serious injury or death to you or bystanders, always follow these precautions  
when working near or handling the battery:  
Always read and follow instructions carefully when handling a battery.  
Wear eye protection designed to protect the eyes from acid splashes.  
Keep all flames, sparks, or smoking materials away from the battery.  
Hydrogen gas is always present in battery cells, is highly combustible, and may explode if  
ignited.  
Keep batteries out of reach of children.  
Batteries contain sulfuric acid that is highly corrosive. Do not allow acid to contact your  
eyes, skin, or clothing.  
If acid gets into your eyes, flush your eyes with clean water for at least 15 minutes and get  
immediate medical attention. If acid gets on your skin, thoroughly wash the area. If you  
feel pain or a burning sensation, get medical attention immediately.  
• When lifting a plastic-cased battery, excessive pressure on the case may cause battery  
acid to leak. Lift with a battery carrier or with your hands on opposite corners.  
• Do not attempt to jump start your vehicle if your battery is frozen.  
Emergency Situations 587  
• Never attempt to recharge the battery when the vehicle's battery cables are connected  
to the battery.  
• The electrical ignition system works with high voltage.  
Never touch these components with the engine running or when the Engine Start/Stop  
button is in the ON position.  
• Do not allow the positive (+) and negative (-) jumper cables to touch. It may cause  
sparks.  
Jump starting procedure  
1
Position the vehicles close enough that the jumper cables can reach. Do not allow the  
vehicles to touch.  
2 Avoid fans or any moving parts in the engine compartment at all times, even when the  
vehicles are turned off.  
3 Turn off all electrical devices such as radios, lights, air conditioning, etc. Put the  
vehicles in P (Park) and apply the parking brake. Turn both vehicles OFF.  
4 Open the engine hood.  
5 Remove the engine compartment fuse box cover.  
CAUTION  
Before jump starting, make sure to correctly identify the positive (+) and negative (-)  
terminals to avoid reverse polarity connections.  
2C_JumpStartOverview  
6 Connect the jumper cables in the exact sequence shown in the illustration. First  
connect one jumper cable to the red, positive (+) battery terminal of your vehicle (1).  
7
Connect the other end of the jumper cable to the red, positive (+) battery/jumper  
terminal of the assisting vehicle (2).  
8 Connect the second jumper cable to the black, negative (-) battery/jumper terminal of  
the assisting vehicle (3).  
9 Connect the other end of the second jumper cable to the chassis ground of your  
vehicle (4).  
588 Emergency Situations  
Do not allow the jumper cables to contact anything except the correct battery or  
jumper terminals or the correct ground. Do not lean over the battery when making  
connections.  
WARNING  
Do not connect the jumper cable to the negative (-) jumper terminal of the discharged  
battery. A spark could cause the battery to explode and lead to a personal injury or  
vehicle damage.  
10 Start the engine of the assisting vehicle and let it run at about 2,000 RPM for a few  
minutes. Then start your vehicle.  
11 Keep your vehicle operating for at least 30 minutes at idle or driving to make sure your  
battery receives enough charge to be able to start on its own after the vehicle is shut  
off. A completely discharged battery may require as long as 60 minutes runtime to fully  
recharge it. If the vehicle has run for less, the vehicle may not restart.  
If your vehicle does not start after a few attempts, it probably requires service. In this  
event please seek qualified assistance. Have your vehicle inspected by an authorized  
HYUNDAI dealer.  
Disconnect the jumper cables in the exact reverse order you connected them:  
1
Disconnect the jumper cable from the chassis ground of your vehicle (4).  
2 Disconnect the other end of the jumper cable from the black, negative (-) battery/  
jumper terminal of the assisting vehicle (3).  
3 Disconnect the second jumper cable from the red, positive (+) battery/jumper terminal  
of the assisting vehicle (2).  
4 Disconnect the other end of the jumper cable from the red, positive (+) jumper  
terminal of your vehicle (1).  
Information  
An inappropriately disposed battery may be harmful to the environment and human  
health. Always dispose of a used battery according to your local law(s) or regulations.  
NOTICE  
To prevent damage to your vehicle:  
• Only use a 12 V power supply (battery or jumper system) to jump start your vehicle.  
• Do not attempt to jump start your vehicle by push-starting.  
Emergency Situations 589  
If The Engine Overheats  
If your temperature gauge indicates overheating, you experience a loss of power, hear  
loud pinging or knocking, or the engine may be overheating. If this happens, you must:  
1
Pull off the road and stop as soon as it is safe to do so.  
2 Shift the gear to P (Park) and apply the parking brake. If the air conditioning is ON, turn  
it OFF.  
3 If engine coolant is running out under the vehicle or steam is coming out from the  
hood, stop the engine. Do not open the hood until the coolant has stopped running or  
the steaming has stopped. If there is no visible loss of engine coolant and no steam,  
leave the engine running and check to make sure the engine cooling fan is operating. If  
the fan is not running, turn off the engine.  
WARNING  
While the engine is running, keep hands, clothing, and tools away from the moving  
parts such as the cooling fan and drive belt to prevent serious injury.  
4 Check for coolant leaking from the radiator, hoses, or under the vehicle. (If the air  
conditioning has been in use, it is normal for cold water to be draining from it when  
you stop.)  
5 If engine coolant is leaking out, stop the engine immediately and call the nearest  
authorized HYUNDAI dealer for assistance.  
WARNING  
Never remove the engine coolant cap or the drain plug while the engine and radiator  
are hot.  
Hot coolant and steam may blow out under pressure, causing serious injury.  
Turn off the engine and wait until the engine cools down. Use extreme care when  
removing the coolant cap. Wrap a thick towel around it, and turn it counterclockwise  
slowly to the first stop. Step back while the pressure is released from the cooling  
system. When you are sure all the pressure has been released, press down on the cap,  
using a thick towel, and continue turning counterclockwise to remove it.  
6 If you cannot find the cause of the overheating, wait until the engine temperature has  
returned to normal.  
Then, if coolant has been lost, carefully add coolant to the reservoir to bring the fluid  
level in the reservoir up to the halfway mark.  
590 Emergency Situations  
7
Proceed with caution, keeping alert for further signs of overheating. If overheating  
happens again, contact an authorized HYUNDAI dealer for assistance.  
CAUTION  
• Serious loss of coolant indicates a leak in the cooling system. Have your vehicle  
inspected by an authorized HYUNDAI dealer.  
• When the engine overheats from low engine coolant, suddenly adding engine coolant  
may cause cracks in the engine. To prevent damage, add engine coolant slowly in  
small quantities. It may require several refilling cycles to properly fill the engine cooling  
system. If necessary, contact an authorized HYUNDAI dealer.  
Emergency Situations 591  
Tire Pressure Monitoring System (TPMS)  
2C_TPMSWarningLampOverview  
2C_TireLowPressureInfo  
1. Low Tire Pressure Telltale/TPMS Malfunction Indicator  
2. Low Tire Pressure Position Telltale and Tire Pressure Telltale (Shown on the cluster display)  
Check tire pressure  
2C_TireLowPressureWarning  
• You can check the tire pressure in the Utility view mode on the cluster.  
Refer to the "Cluster display control" section in chapter 4.  
• Tire pressure appears after a few minutes of driving. If the tire pressure does not  
appear when the vehicle is stopped, the message, “Drive to display” appears.  
• The displayed tire pressure values may differ from those measured with a tire pressure  
gauge.  
592 Emergency Situations  
• You can change the tire pressure unit from the Settings menu in the infotainment  
system. Select:  
- Setup > General > Unit > Tire Pressure Unit > psi/kPa/bar  
Information  
The infotainment system may change after software updates. For more information, refer  
to the user's manual provided in the infotainment system and the quick reference guide.  
Tire Pressure Monitoring System  
WARNING  
Over-inflation or under-inflation can reduce tire life, adversely affect vehicle handling, and  
lead to sudden tire failure that may cause loss of vehicle control resulting in a collision.  
Each tire, including the spare (if provided), should be checked monthly when cold and  
inflated to the inflation pressure recommended by the vehicle manufacturer on the  
vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size  
than the size indicated on the vehicle placard or tire inflation pressure label, you should  
determine the proper tire inflation pressure for those tires.)  
As an added safety feature, your vehicle has been equipped with a Tire Pressure  
Monitoring System (TPMS) that illuminates a low tire pressure telltale when one or more  
of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale  
illuminates, you should stop and check your tires as soon as possible, and inflate them  
to the proper pressure. Driving on a significantly under-inflated tire causes the tire to  
overheat and can lead to tire failure.  
Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle's  
handling and stopping ability.  
Please note that the TPMS is not a substitute for proper tire maintenance, and it is the  
driver's responsibility to maintain correct tire pressure, even if under-inflation has not  
reached the level to trigger illumination of the TPMS low tire pressure telltale.  
Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when  
the system is not operating properly. The TPMS malfunction indicator is combined with  
the low tire pressure telltale. When the system detects a malfunction, the telltale will flash  
for approximately one minute and then remain continuously illuminated. This sequence  
will continue upon subsequent vehicle start-ups as long as the malfunction exists.  
When the malfunction indicator is illuminated, the system may not be able to detect  
or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of  
reasons, including the installation of replacement or alternate tires or wheels on the  
vehicle that prevent the TPMS from functioning properly.  
Always check the TPMS malfunction telltale after replacing one or more tires or wheels on  
your vehicle to ensure that the replacement or alternate tires and wheels allow the TPMS  
to continue to function properly.  
Emergency Situations 593  
NOTICE  
Have the system inspected by an authorized HYUNDAI dealer if:  
• The Low Tire Pressure Telltale/TPMS Malfunction Indicator does not illuminate for 3  
seconds when the Engine Start/Stop button is set to the ON position or the engine is  
running.  
• The TPMS Malfunction Indicator remains illuminated after blinking for about 1 minute.  
• The Low Tire Pressure Position Telltale remains illuminated.  
Low tire pressure indicator  
Low Tire Pressure Warning Light  
2C_TireLowPressureWarningLamp  
Low tire pressure position and tire pressure telltale  
Low Tire Pressure Position and Tire Pressure Telltale  
2C_TireLowPressureWarning  
When the Tire Pressure Monitoring System warning indicator (  
) is illuminated and  
a warning message appears on the cluster display, one or more of your tires is  
significantly under-inflated. The Low Tire Pressure Position Telltale will indicate which  
tire is significantly under inflated by illuminating the corresponding parking light.  
If either telltale illuminates, immediately reduce your speed, avoid hard cornering and  
anticipate increased stopping distances. You should stop and check your tires as soon as  
possible. Inflate the tires to the proper pressure as indicated on the vehicle's placard or  
tire inflation pressure label located on the driver's side center pillar outer panel.  
594 Emergency Situations  
If you cannot reach a service station or if the tire cannot hold the newly added air, replace  
the low pressure tire with the spare tire.  
The Low Tire Pressure position indicator will remain on and the TPMS Malfunction  
Indicator may blink for one minute and then remain illuminated until you have the low  
pressure tire repaired and replaced on the vehicle.  
CAUTION  
In winter or cold weather, the Low Tire Pressure Telltale may be illuminated if the tire  
pressure was adjusted to the recommended tire inflation pressure in warm weather. It  
does not mean your TPMS is malfunctioning because the decreased temperature leads to  
a proportional lowering of tire pressure.  
When you drive your vehicle from a warm area to a cold area or from a cold area to a  
warm area, or the outside temperature is greatly higher or lower, check the tire inflation  
pressure and adjust the tires to the recommended tire inflation pressure.  
WARNING  
Low pressure damage  
Significantly low tire pressure makes the vehicle unstable and may contribute to loss of  
vehicle control and increased braking distances.  
Continued driving on low pressure tires may cause the tires to overheat and fail.  
TPMS malfunction indicator  
2C_TPMSMalfunctionOverview  
The TPMS Malfunction Indicator (  
) illuminates after it blinks for about one minute  
when there is a problem with the Tire Pressure Monitoring System.  
Have the system inspected by an authorized HYUNDAI dealer as soon as possible.  
NOTICE  
If there is a malfunction with the TPMS, the individual tire pressures on the cluster display  
are not available. Have the system inspected by an authorized HYUNDAI dealer as soon as  
possible.  
Emergency Situations 595  
NOTICE  
The TPMS Malfunction Indicator may illuminate after blinking for one minute if the  
vehicle is near electric power supply cables or radio transmitters such as police stations,  
government and public offices, broadcasting stations, military installations, airports,  
transmitting towers, etc.  
Additionally, the TPMS Malfunction Indicator may illuminate if snow chains are used or if  
electronic devices such as computers, chargers, remote starters, navigation, etc. are near  
the vehicle. This may interfere with normal operation of the TPMS.  
Changing a tire with TPMS  
If you have a flat tire, the Low Tire Pressure and Position telltales come on. Have the flat  
tire repaired by an authorized HYUNDAI dealer as soon as possible or replace the flat tire  
with the spare tire.  
NOTICE  
It is recommended that you do not use a puncture-repairing agent not approved by  
HYUNDAI dealer or the equivalent specified for your vehicle to repair and/or inflate a low  
pressure tire. Tire sealant not approved by HYUNDAI dealer or the equivalent specified for  
your vehicle may damage the tire pressure sensor.  
The spare tire (if equipped) does not come with a tire pressure monitoring sensor. When  
the low pressure tire or the flat tire is replaced with the spare tire, the Low Tire Pressure  
Telltale remains on. Also, the TPMS Malfunction Indicator illuminates after blinking for one  
minute if the vehicle is driven at the speed above 15.5 mph (25 km/h) for about 10 minutes.  
Once the original wheel equipped with a tire pressure monitoring sensor is reinflated to  
the recommended pressure and reinstalled on the vehicle, the Low Tire Pressure Telltale  
and TPMS Malfunction Indicator goes off within a few minutes of driving.  
If the indicators do not turn off after a few minutes, visit an authorized HYUNDAI dealer.  
Each wheel is equipped with a tire pressure sensor mounted inside the tire behind the  
valve stem (except for the spare tire). You must use TPMS specific wheels. Always have  
your tires serviced by an authorized HYUNDAI dealer.  
You may not be able to identify a tire with low pressure by simply looking at it. Always  
use a good quality tire pressure gauge to measure. Please note that a tire that is hot (from  
being driven) has a higher pressure measurement than a tire that is cold.  
A cold tire means the vehicle has been sitting for 3 hours and driven for less than 1 mile  
(1.6 km) in that 3 hour period.  
Allow the tire to cool before measuring the inflation pressure. Always make sure the tire is  
cold before inflating to the recommended pressure.  
WARNING  
• The TPMS cannot alert you to severe and sudden tire damage caused by external  
factors such as nails or road debris.  
• If you feel any vehicle instability, immediately take your foot off the accelerator pedal,  
apply the brakes gradually with light force, and slowly move to a safe position off the  
road.  
596 Emergency Situations  
WARNING  
Tampering with, modifying, or disabling the Tire Pressure Monitoring System (TPMS)  
components may interfere with the system's ability to warn the driver of low tire pressure  
conditions and/or TPMS malfunctions and may void the warranty.  
WARNING  
This device complies with Part 15 of the FCC rules.  
Operation is subject to the following three conditions:  
1
This device may not cause harmful interference.  
2 This device must accept any interference received, including interference that may  
cause undesired operation of the device.  
3 Changes or modifications not expressly approved by the party responsible for  
compliance could void the user's authority to operate the device.  
Emergency Situations 597  
If You Have A Flat Tire (With Spare Tire)  
WARNING  
Follow the instructions in this section when replacing a tire to reduce the risk of serious  
injury or death. Changing a tire can be dangerous.  
Jack and tools  
2C_SpareTireReplacementOverview  
1. Jack handle  
2. Jack  
3. Wheel lug wrench  
The jack, jack handle, and wheel lug nut wrench are stored in the cargo area under the  
luggage box cover.  
The jack is provided for emergency tire changing only.  
2C_SpareTireReplacementPrecedure  
Turn the winged hold down bolt counterclockwise to remove the spare tire.  
Store the spare tire in the same compartment by turning the winged hold down bolt  
clockwise.  
To prevent the spare tire and tools from "rattling", store them in their proper locations.  
598 Emergency Situations  
2C_SpareTireReplacementPrecedure_2  
If it is hard to loosen the tire hold down wing bolt by hand, you can loosen it easily using  
the wheel lug wrench.  
Turn the tire hold down wing bolt counterclockwise with the wheel lug wrench.  
Changing tires  
WARNING  
Because the vehicle may slip or roll off of a jack causing serious injury or death, take the  
following safety precautions:  
• NEVER place any portion of your body under the vehicle that is supported by a jack.  
• NEVER attempt to change a tire in the lane of traffic. ALWAYS move the vehicle  
completely off the road on a level, firm ground away from traffic before trying to  
change a tire. If you cannot find a level, firm place off the road, call a towing service for  
assistance.  
• ONLY use the jack provided with the vehicle.  
• ALWAYS place the jack on the designated jacking positions on the vehicle and NEVER  
on the bumpers or any other part of the vehicle for jacking support.  
• Do not start or run the engine while the vehicle is on the jack.  
• Do not allow anyone to remain in the vehicle while it is on the jack.  
• Keep children away from the road and the vehicle.  
Keep the following steps to change your vehicle's tire:  
1
Park on a level, firm surface.  
2 Shift the gear to P (Park), apply the parking brake, and press the Engine Start/Stop  
button to the OFF position.  
3 Press the hazard warning flasher button.  
4 Remove the wheel lug wrench, jack, jack handle, and spare tire from the vehicle.  
Emergency Situations 599  
5 Block both the front and rear of the tire diagonally opposite of the tire you are  
changing.  
2C_SpareTireReplacementPrecedure_3  
[A] Block  
6 Loosen the wheel nuts counterclockwise one turn each in the order shown below, but  
do not remove any wheel nuts until the tire has been raised off of the ground.  
2C_SpareTireReplacementPrecedure_4  
7
Place the jack at the designated jacking position under the frame closest to the tire you  
are changing. The jacking positions are plates welded to the frame with two notches.  
Never jack any other position or part of the vehicle to prevent the vehicle slipping off of  
the jack or damaging the vehicle.  
2C_SpareTireReplacementPrecedure_5  
600 Emergency Situations  
8 Insert the jack handle into the jack and turn it clockwise, raising the vehicle until the  
tire clears the ground. Make sure the vehicle is stable on the jack.  
2C_SpareTireReplacementPrecedure_6  
9 Loosen the wheel nuts with the wheel lug wrench and remove them with your fingers.  
Remove the wheel from the studs and lay it flat on the ground out of the way. Remove  
any dirt or debris from the studs, mounting surfaces, and spare tire.  
WARNING  
Because the wheels may have sharp edges, handle them carefully to avoid possible  
severe injury. Before putting the wheel into place, make sure that there is nothing on  
the hub or wheel (such as mud, tar, gravel, etc.) that interferes with the wheel from  
fitting solidly against the hub.  
If there is, remove it. If there is not good contact on the mounting surface between the  
wheel and hub, the wheel nuts may come loose and cause the loss of a wheel. Loss  
of a wheel may result in loss of control of the vehicle. This may cause serious injury or  
death.  
10 Install the spare tire onto the studs of the hub.  
11 Tighten the wheel nuts with your fingers onto the studs with the smaller end of the  
wheel nuts closest to the wheel.  
12 Lower the vehicle to the ground by turning the jack handle counterclockwise.  
13 Use the wheel lug nut wrench to tighten the wheel nuts in the order shown. Double-  
check each wheel nut until they are tight. After changing tires, have an authorized  
HYUNDAI dealer tighten the lug nuts to their proper torque as soon as possible.  
Emergency Situations 601  
Tighten wheel nuts to 79-94 lbf.ft (11-13 kgf.m).  
2C_SpareTireReplacementPrecedure_7  
Check the tire pressure after installing the compact spare tire. The compact spare tire  
should be inflated to 60 psi (420 kPa).  
If you have a tire gauge, check the tire pressure (refer to the"Tires and wheels" section  
in chapter 2 for tire pressure instructions). If the spare tire pressure is lower or higher  
than the recommended, drive slowly to the nearest service station and adjust it to the  
recommended pressure.  
Always reinstall the valve cap after checking or adjusting the tire pressure. If the cap is not  
replaced, air may leak from the tire. If you lose a valve cap, buy another and install it as  
soon as possible. After changing tires, secure the flat tire and return the jack and tools to  
their proper storage locations.  
NOTICE  
Check the tire pressure as soon as possible after installing a spare tire. Adjust it to the  
recommended pressure.  
WARNING  
Your vehicle has metric threads on the studs and wheel nuts. During tire changing, make  
sure that the wheel nuts that were removed are reinstalled. If you have to replace your  
wheel nuts, make sure they have metric threads to avoid damaging the studs and make  
sure the wheel is properly secured to the hub. Contact an authorized HYUNDAI dealer for  
assistance.  
If any of the equipment such as the jack, wheel nuts, studs, or other equipment is  
damaged or in poor condition, do not attempt to change the tire and call for assistance.  
Use of compact spare tires  
Compact spare tires are designed for emergency use only. Drive carefully on the compact  
spare tire and always follow the safety precautions.  
602 Emergency Situations  
WARNING  
To prevent compact spare tire failure and loss of control, possibly resulting in a collision:  
• Use the compact spare tire only in an emergency.  
• NEVER operate your vehicle over 50 mph (80 km/h).  
• Do not exceed the vehicle's maximum load rating or the load carrying capacity shown  
on the sidewall of the compact spare tire.  
• Do not use the compact spare tire continuously. Repair or replace the original tire as  
soon as possible to avoid failure of the compact spare tire.  
When driving with the compact spare tire mounted to your vehicle:  
• Do not take this vehicle through an automatic car wash after the compact spare tire  
has been installed.  
• Do not use the compact spare tire on any other vehicle because this tire has been  
designed especially for your vehicle.  
• The compact spare tire's tread life is shorter than a regular tire. Inspect your compact  
spare tire regularly and replace worn compact spare tires with the same size and  
design, mounted on the same wheel.  
• Do not use more than one compact spare tire at a time.  
• Do not tow a trailer while the compact spare tire is installed.  
NOTICE  
When the original tire and wheel are repaired and reinstalled on the vehicle, the wheel nut  
torque must be set correctly. The correct wheel nut tightening torque is 79-94 lbf.ft (11-13  
kgf.m).  
CAUTION  
To prevent damaging the compact spare tire and your vehicle:  
• Drive slowly enough for the road conditions to avoid all hazards, such as a potholes or  
debris.  
• Avoid driving over obstacles. The compact spare tire diameter is smaller than the  
diameter of a conventional tire and reduces the ground clearance about 1 inch (25 mm).  
• Do not use tire chains on the compact spare tire. Because of the smaller size, a tire  
chain will not fit properly.  
• Do not use the compact spare tire on any other wheels, nor should standard tires, snow  
tires, wheel covers or trim rings be used with the compact spare wheel.  
• Do not suddenly accelerate or decelerate (0-25 mph (0-40 km/h)) in any driving mode.  
It may cause leakage of transfer oil.  
Emergency Situations 603  
Jack label  
1C_JackLabel  
1. Model Name  
2. Maximum allowable load  
3. Always apply the parking brake before using a jack.  
4. Always turn off the engine before using a jack.  
5. Never put any portion of your body under the vehicle supported by a jack.  
6. Only use the designated jacking locations on the frame.  
7. When supporting the vehicle, have the base plate of the jack flat on the ground under  
the lifting point.  
8. Shift into R (Reverse) gear with manual transmission or shift the gear to the P  
(Park) position on vehicles with automatic transmission, dual clutch transmission, and  
intelligent variable transmission.  
9. Do not jack the vehicle on an incline. Only jack the vehicle on a firm level ground.  
10.Jack manufacturer  
11. Production date  
12. Representative company and address  
The actual Jack label in the vehicle may differ from the illustration.  
For more detailed specifications, refer to the label attached to the jack.  
604 Emergency Situations  
If You Have A Flat Tire (With Tire Mobility Kit)  
if equipped  
2C_TMKOverview  
1. Compressor  
2. Sealant bottle  
For safe operation, carefully read and follow the instructions in this manual before use.  
The Tire Mobility Kit is a temporary fix to the tire, have the tire replaced by an authorized  
HYUNDAI dealer as soon as possible.  
CAUTION  
When two or more tires are flat, do not use the Tire Mobility Kit because the sealant  
provided with the Tire Mobility Kit must be used for only one flat tire.  
WARNING  
• Do not use the Tire Mobility Kit to repair punctures in the tire walls. This can result in an  
accident due to tire failure.  
• Have your tire repaired as soon as possible. The tire may lose air pressure at any time  
after inflating with the Tire Mobility Kit.  
Introduction  
With the Tire Mobility Kit you stay mobile even after experiencing a tire puncture.  
The compressor and sealing compound system effectively and comfortably seals most  
punctures in a passenger car tire caused by nails or similar objects and reinflates the tire.  
After you are ensure that the tire is properly sealed you can drive cautiously on the tire  
(distance up to 120 miles (200 km)) at a maximum speed of 50 mph (80 km/h) in order to  
reach a service station or tire dealer for tire replacement.  
It is possible that some tires, especially with larger punctures or damage to the sidewall,  
cannot be sealed completely.  
Air pressure loss in the tire may adversely affect tire performance.  
For this reason, you should avoid abrupt steering or other driving maneuvers, especially if  
the vehicle is heavily loaded or if a trailer is in use.  
The Tire Mobility Kit is not designed or intended as a permanent tire repair method and is  
to be used for one tire only.  
Emergency Situations 605  
This instruction shows you step by step how to temporarily seal the puncture simply and  
reliably.  
Read the section "Notes on the safe use of the Tire Mobility Kit".  
Notes on the safe use of the Tire Mobility Kit  
• Park your vehicle at the side of the road so that you can work with the Tire Mobility Kit  
away from moving traffic.  
• To be sure your vehicle does not move, even when you are on level ground, always  
apply your parking brake.  
• Only use the Tire Mobility Kit for sealing/inflation passenger car tires. Only punctured  
areas located within the tread region of the tire can be sealed using the tire mobility kit.  
• Do not use on motorcycles, bicycles or any other type of tires.  
• When the tire and wheel are damaged, do not use Tire Mobility Kit.  
• Use of the Tire Mobility Kit may not be effective for tire damage larger than about 0.16  
inches (4 mm).  
Contact an authorized HYUNDAI dealer if the tire cannot be made roadworthy with the  
Tire Mobility Kit.  
• Do not use the Tire Mobility Kit if a tire is severely damaged by driving run flat or with  
insufficient air pressure.  
• Only punctured areas located within the tread region of the tire can be sealed using the  
Tire Mobility Kit.  
• Do not remove any foreign objects such as nails or screws that have penetrated the tire.  
• Provided the vehicle is outdoors, leave the vehicle running. Otherwise operating the  
compressor may eventually drain the car battery.  
• Never leave the Tire Mobility Kit unattended while it is being used.  
• Do not leave the compressor running for more than 10 minutes at a time or it may  
overheat.  
• Do not use the Tire Mobility Kit if the ambient temperature is below -22 °F (-30 °C).  
• In case of skin contact with the sealant, wash the area thoroughly with plenty of water.  
If the irritation persists, seek medical attention.  
• In case of eye contact with the sealant, flush your eyes for at least 15 minutes. If the  
irritation persists, seek medical attention.  
• In case of swallowing the sealant, rinse the mouth and drink plenty of water. However,  
never give anything to an unconscious person and seek medical attention immediately.  
• Long time exposure to the sealant may cause damage to bodily tissue such as kidney,  
etc.  
606 Emergency Situations  
Components of the Tire Mobility Kit  
1C_TMKPartsOverveiw  
1. Speed restriction label  
2. Sealant bottle  
3. Filling hose from sealant bottle to wheel  
4. Connectors and cable for the power outlet direct connection  
5. Holder for the sealant bottle  
6. Compressor  
7. ON/OFF switch  
8. Pressure gauge for displaying the tire inflation pressure  
9. Button for reducing the tire inflation pressure  
Strictly follow the specified sequence, otherwise the sealant may escape under high  
pressure.  
WARNING  
Do not use the tire sealant after the sealant has expired (the expiration date is pasted on  
the sealant container). This can increase the risk of tire failure.  
Emergency Situations 607  
WARNING  
Sealant  
• Keep out of reach of children.  
• Avoid contact with eyes.  
• Do not swallow.  
Using the Tire Mobility Kit when a tire is flat  
CAUTION  
2C_HowToUseTMK  
Detach the speed restriction label (1) from the sealant bottle (2), and place it in a highly  
visible place inside the vehicle such as on the steering wheel to remind the driver not to  
drive too fast.  
CAUTION  
If only the tire pressure needs to be adjusted, refer to the "How to adjust tire pressure"  
section in this chapter.  
Before using the Tire Mobility Kit, be fully aware of the explanation on the sealant.  
1
Shake the sealant bottle (2).  
2C_TMKPrecedure  
608 Emergency Situations  
2 Remove the sealant bottle (2) cap and sealant bottle holder (5) cap and screw the  
bottle onto the sealant bottle holder.  
2C_TMKPrecedure_2  
3 Make sure the compressor valve on the filling hose is locked.  
4 Unscrew the valve cap and screw the filling hose (3) onto the tire valve.  
2C_TMKPrecedure_6  
CAUTION  
Securely install the sealant filling hose to the valve. If not, sealant may flow backward,  
possibly clogging the filling hose.  
5 Make sure the compressor is turned off and plug the compressor power cord (4) into  
the vehicle power outlet.  
2C_TMKPrecedure_4  
Emergency Situations 609  
WARNING  
Do not connect another vehicle's Tire Mobility Kit to the power outlet. This may cause a  
fire due to the difference in current capacity.  
6 With the engine ON, switch on the compressor and let it run for about 5-7 minutes  
to fill the sealant up to proper pressure. (refer to the "Tires and wheels" section in  
chapter 2). The inflation pressure of the tire after filling is unimportant and can be  
checked/corrected later.  
Be careful not to overinflate the tire and stay away from the tire when filling it.  
CAUTION  
Do not attempt to drive your vehicle if the tire pressure is below 29 psi (200 kPa). This  
could result in an accident due to sudden tire failure.  
7
Switch off the compressor.  
8 Detach the hoses from the sealant bottle connector and from the tire valve.  
Return the Tire Mobility Kit to its storage location in the vehicle.  
9 Immediately drive about 4-6 miles (7-10 km or about 10 minutes) to evenly distribute  
the sealant in the tire.  
2C_TMKPrecedure_5  
Do not exceed a speed of 50 mph (80 km/h). If possible, do not fall below a speed of 12  
mph (20 km/h).  
While driving, if you experience any unusual vibration, ride disturbance or noise,  
reduce your speed and drive with caution until you can safely pull off of the side of  
the road.  
Call for road side service or towing.  
10 After driving about 4-6 miles (7-10 km or about 10 minutes), stop at a safety location.  
610 Emergency Situations  
11 Connect the filling hose (3) of the compressor directly to the tire valve.  
2C_TMKPrecedure_3  
12 Plug the compressor power cord into the vehicle power outlet.  
13 Adjust the tire inflation pressure to the recommended tire inflation.  
With the engine running, proceed as follows:  
• To increase the inflation pressure: Switch on the compressor. To check the current  
inflation pressure setting, briefly switch off the compressor.  
• To reduce the inflation pressure: Press the button (9) on the compressor.  
NOTICE  
Do not let the compressor run for more than 10 minutes, otherwise the device may  
overheat and may be damaged.  
Information  
The pressure gauge may show higher than actual reading when the compressor is  
running. To get an accurate tire pressure, the compressor needs to be turned off.  
CAUTION  
• If the tire inflation pressure is not maintained, drive the vehicle a second time, refer to  
step 9. Then repeat steps 10 to 13.  
• Use of the Tire Mobility Kit may not be effective for tire damage larger than about 0.16  
inches (4 mm).  
Contact an authorized HYUNDAI dealer if the tire cannot be made roadworthy with the  
Tire Mobility Kit.  
WARNING  
The tire inflation pressure must be inflated to the proper pressure, refer to the "Tires and  
wheels" section in chapter 2. If it is not inflated, do not continue to drive.  
Call for road side service or towing.  
Emergency Situations 611  
CAUTION  
Tire pressure sensor  
The sealant on the tire pressure sensor and wheel should be removed when you replace  
the tire with a new one and inspect the tire pressure sensors. Have this done at an  
authorized HYUNDAI dealer.  
Information  
When reinstalling the repaired or replaced tire and wheel on the vehicle, tighten the  
wheel nut to 79-94 lbf·ft (11-13 kgf·m).  
How to adjust tire pressure  
2C_TMKPrecedure_3  
1
Park your vehicle in a safe location.  
2 Connect the filling hose (3) of the compressor directly to the tire valve.  
3 Plug the compressor power cord (4) into the vehicle power outlet.  
4 Adjust the tire inflation pressure to the recommended tire inflation.  
With the engine running, proceed as follows:  
• To increase the inflation pressure: Switch on the compressor. To check the current  
inflation pressure setting, briefly switch off the compressor.  
• To reduce the inflation pressure: Press the button (9) on the compressor.  
NOTICE  
Do not let the compressor run for more than 10 minutes, otherwise the device may  
overheat and may be damaged.  
Information  
• The pressure gauge may show higher than actual reading when the compressor is  
running. To get an accurate tire reading, the compressor needs to be turned off.  
• When reinstalling the repaired or replaced tire and wheel on the vehicle, tighten the  
wheel nut to 79-94 lbf·ft (11-13kgf·m).  
612 Emergency Situations  
CAUTION  
Do not use the sealant when the tire pressure only needs to be adjusted.  
WARNING  
The tire inflation pressure must be inflated to the proper pressure, refer to the "Tires and  
wheels" section in chapter 2. If it is not inflated, do not continue to drive.  
Call for road side service or towing.  
Emergency Situations 613  
Towing  
Towing service  
Flatbed Towing  
2C_TowingGood  
Wheel lift Towing  
2C_TowingGood_2  
1. Dollies  
If towing is necessary, contact an authorized HYUNDAI dealer or a commercial tow-truck  
service.  
AWD vehicles must be towed with a wheel lift and dollies or flatbed with all the wheels off  
the ground.  
2WD vehicles can be towed with the rear wheels on the ground (without dollies) and the  
front wheels off the ground.  
The use of wheel dollies or flatbed is recommended. If any of the loaded wheels or  
suspension components are damaged or the vehicle is towed with the front wheels on the  
ground, use a towing dolly under the front wheels.  
614 Emergency Situations  
NOTICE  
To prevent damage when towing:  
• Do not lift using the trailer hitch or body and chassis parts.  
• Do not tow the vehicle with the front wheels on the ground.  
2C_TowingBad  
• Do not tow vehicles with sling-type equipment. Only use wheel lift or flatbed  
equipment.  
2C_TowingBad_2  
When towing your vehicle without wheel dollies:  
1
Release the parking brake before turning off the engine.  
2 Press the Engine Start/Stop button to the OFF position.  
3 Change the gear to N (Neutral) while depressing the brake pedal.  
4 Press the Engine Start/Stop button to the ACC position.  
WARNING  
If your vehicle is equipped with a rollover sensor, Press the Engine Start/Stop button to  
the OFF or ACC position when the vehicle is being towed. The side impact and curtain  
airbag may deploy if the sensor detects the situation as a rollover.  
Information  
Always shift the gear to N (Neutral) to prevent damage to the transmission before towing.  
Emergency Situations 615  
Removable towing hook  
Front  
2C_TowingHook  
Rear  
2C_TowingHook_2  
1. Install  
2. Remove  
1
Open the liftgate and remove the towing hook from the tool case.  
2 Remove the hole cover pressing the lower part of the cover on the bumper.  
3 Install the towing hook by turning it clockwise into the hole until it is fully secured.  
4 Remove the towing hook and install the cover after use.  
NOTICE  
Failure to properly tighten the towing hook may result in vehicle damage and deformation  
of related parts.  
CAUTION  
Make sure the towing hook is tighten properly. If not, during towing the towing hook may  
be thrown off the vehicle resulting in serious injury or accident.  
616 Emergency Situations  
Emergency towing  
Front  
2C_TowingHookWithGeneralVehicle  
Rear  
2C_TowingHookWithGeneralVehicle_2  
If emergency towing is necessary, contact an authorized HYUNDAI dealer or a  
commercial tow-truck service.  
If tow-truck service is not available in an emergency, your vehicle can be temporarily  
towed using a cable or chain secured to the removable towing hook at the front (or rear)  
of the vehicle.  
Perform emergency towing using cables or chains on hard-surfaced roads for a short  
distance and at low speeds. The wheels, axles, powertrain, steering, and brakes must all  
be in good working condition.  
WARNING  
Use extreme caution when towing the vehicle with a cable or chain. A driver must be in  
the vehicle to steer it and operate the brakes. Passengers other than the driver must not  
be in the vehicle.  
Always follow these emergency towing precautions:  
• Press the Engine Start/Stop button to the ACC position so the steering wheel is not  
locked.  
• Shift the gear in N (Neutral).  
Emergency Situations 617  
• Release the parking brake.  
• Depress the brake pedal with more force than normal because you have reduced  
braking performance.  
• More steering effort is required because the power steering system will be disabled.  
• Use a vehicle heavier than your own to tow your vehicle.  
• The drivers of both vehicles must communicate with each other frequently.  
• Before emergency towing, check that the removable hook is not broken or damaged.  
• Fasten the towing cable or chain securely to the hook.  
• Do not jerk the cables, chains, or removable hook. Apply steady and even force.  
• Use a towing cable or chain less than 16 ft. (5 m) long. Attach a white or red cloth  
(about 12 inches (30 cm) wide) in the middle of the cable or chain for easy visibility.  
2C_TowingHookRange  
1. 16 ft. (5m)  
• Drive carefully so the towing cable or chain remains tight during towing.  
• Before towing, check the Automatic Transmission, and Intelligent Variable Transmission  
for fluid leaks under your vehicle. If the transmission fluid is leaking, flatbed equipment  
or a towing dolly must be used.  
NOTICE  
Accelerate or decelerate the vehicle in a slow and gradual manner while maintaining  
tension on the tow rope or chain to start or drive the vehicle. Otherwise tow hooks and  
the vehicle may be damaged.  
NOTICE  
To avoid damage to your vehicle and vehicle components when towing:  
• Always pull straight ahead when using the towing hooks. Do not pull from the side or at  
a vertical angle.  
• Do not use the towing hooks to pull the vehicle out of mud, sand, or other conditions  
from which the vehicle cannot be driven out under its own power.  
• Limit the vehicle speed to 10 mph (15 km/h) and drive less than 1 mile (1.6 km) when  
towing to avoid serious damage to transmission.  
618 Emergency Situations  

Related Topics

Hazard warning flasher In case of an emergency while driving If the engine does not start If the engine overheats If you have a flat tire (With spare tire) If you have a flat tire (with Tire Mobility Kit) Towing

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot