2004-2009 Hyundai Tucson SUV CORROSION PREVENTION & APPEARANCE CARE -> WASHING AND WAXING User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

CORROSION PREVENTION & APPEARANCE CARE -> WASHING AND WAXING for Your Hyundai Tucson SUV First Generation (2004-2009)

44
CORROSION PREVENTION AND APPEARANCE CARE
4
WASHING AND WAXING
E030A03A-AAT
Washing Your Hyundai
Never wash your car when the surface
is hot from being in the sun. Always
wash your car in the shade.
Wash your car frequently. Dirt is abra-
sive and can scratch the paint if it is not
removed. Air pollution or acid rain may
damage the paint and trim through
chemical action if pollutants are al-
lowed to remain in contact with the
surface. If you live near the ocean or in
an area where road salts or dust con-
trol chemicals are used, you should
pay particular attention to the under-
side of the car. Start by rinsing the car
to remove dust and loose dirt. In win-
ter, or if you have driven through mud
or muddy water, be sure to thoroughly
clean the underside as well. Use a
hard direct stream of water to remove
accumulations of mud or corrosive
materials. Use a good quality car-wash-
ing solution and follow the manufac-
turer's directions on the package.
These are available at your Hyundai
dealer or auto parts outlet. Don't use
strong household detergents, gaso-
line, strong solvents or abrasive clean-
ing powders as these may damage the
finish.
Use a clean sponge or cloth, rinse it
frequently and don't damage the finish
by rubbing too hard. For stubborn spots,
dampen them frequently and remove
them a little at a time.
To clean whitewall tires, use a stiff
brush or soapy steel-wool scouring
pad.
To clean plastic wheel covers, use a
clean sponge or soft cloth and water.
To clean cast aluminum alloy wheels,
use a mild soap or neutral detergent.
Do not use abrasive cleaners. Protect
the bare-metal surfaces by cleaning,
polishing and waxing. Because alumi-
num is subject to corrosion, be sure to
give aluminum alloy wheels special
attention in winter. If you drive on
salted roads, clean the wheels thor-
oughly afterwards.
After washing, be sure to rinse thor-
oughly. If soapy water dries on the
finish, streaking will result.
When the weather is warm and the
humidity low, you may find it neces-
sary to rinse each section immediately
after washing to avoid streaking.
After rinsing, dry the car using a damp
chamois or soft, absorbent cloth. The
reason for drying the car is to remove
water from the car so it will dry without
water spots. Don't rub, this can dam-
age the finish.
If you find any nicks or scratches in the
paint, use touch-up paint to cover them
to prevent corrosion. To protect the
paintwork of the car against corrosion,
you must clean your Hyundai (at least
once a month). Give special attention
to the removal of salt, mud and other
substances on the underside of the
splashboards of the car. Make sure
that the outlets and the underside of
the doors are open. Paint damage can
be caused by small accumulation of
tar, industrial precipitation, tree resin,
insects and bird droppings, when not
removed immediately. If water alone is
not strong enough to remove the accu-
mulated dirt, use a mild car washing
4
CORROSION PREVENTION AND APPEARANCE CARE
5
4
CORROSION PREVENTION AND APPEARANCE CARE
5
E030D01A-AAT
When to Wax Again
You should polish and wax the car
again when water no longer beads on
a clean surface but spreads out over a
larger area.
E030E01A-AAT
Maintaining Bumpers
Special precautions must be observed
to preserve the appearance of the
bumpers on your Hyundai. They are:
o Be careful not to spill battery elec-
trolyte or hydraulic brake fluid on the
bumpers. If you do, wash it off
immediately with clean water.
o Be gentle when cleaning the bumper
surfaces. They are made of soft
plastic and the surface can be dam-
aged if mistreated. Do not use abra-
sive cleaners. Use warm water and
mild soap or car-washing solution.
o Do not expose the bumpers to high
temperatures. For example, if you
have your car repainted, do not
leave the bumpers on the car if the
car is going to be placed in a high-
temperature paint booth.
E030B01A-AAT
Spot Cleaning
Don't use gasoline, strong solvents or
corrosive cleaning agents. These can
damage the finish of the car. To re-
move road tar, use turpentine on a
clean, soft cloth or commercially avail-
able bug and tar remover. Be gentle.
To remove dead insects or tree sap,
use warm water and mild soap or car-
washing solution. Soak the spot and
rub gently. If the paint has lost its
luster, use a commercial car-cleaning
polish.
E030C01A-AAT
Polishing and Waxing
Always wash and dry the car before
polishing or waxing or using a combi-
nation cleaner and wax. Use a good
quality commercial product and follow
the manufacturer's directions on the
container. Polish and wax the bright
trim pieces as well as the paint.
solution. Be sure to rinse the surface
after washing to remove the solution.
Never allow the solution to dry on the
painted surfaces.
CAUTION:
!
o Water washing in the engine com-
partment including high pressure
water washing may cause the fail-
ure of electrical circuits located in
the engine compartment.
o Never allow water or other liquids
to come in contact with electrical/
electronic components inside the
vehicle as this may damage them.
OJB037800

Related Topics

Popular Owner Manuals