2006-2012 Kia Ceed SUV Maintenance -> Exterior care User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Maintenance -> Exterior care for Your Kia Ceed SUV First Generation (2006-2012)

ED English 7.qxp 10/8/2007 5:52 PM Page 63  
Maintenance  
EXTERIOR CARE  
Even prompt washing with plain  
water may not completely remove all  
these deposits. A mild soap, safe for  
use on painted surfaces, may be  
used.  
Exterior general caution  
It is very important to follow the label  
directions when using any chemical  
cleaner or polish. Read all warning  
and caution statements that appear  
on the label.  
After washing, rinse the vehicle thor-  
oughly with lukewarm or cold water.  
Do not allow soap to dry on the fin-  
ish.  
Finish maintenance  
Washing  
To help protect your vehicle’s finish  
from rust and deterioration, wash it  
thoroughly and frequently at least  
once a month with lukewarm or cold  
water.  
CAUTION  
OJB037800  
Do not use strong soap, chemi-  
cal detergents or hot water, and  
do not wash the vehicle in direct  
sunlight or when the body of the  
vehicle is warm.  
CAUTION  
• Water washing in the engine  
compartment including high  
pressure water washing may  
cause the failure of electrical  
circuits located in the engine  
compartment.  
If you use your vehicle for off-road  
driving, you should wash it after each  
off-road trip. Pay special attention to  
the removal of any accumulation of  
salt, dirt, mud, and other foreign  
materials. Make sure the drain holes  
in the lower edges of the doors and  
rocker panels are kept clear and  
clean.  
WARNING  
After washing the vehicle, test  
the brakes while driving slowly  
to see if they have been affected  
by water. If braking performance  
is impaired, dry the brakes by  
applying them lightly while  
maintaining a slow forward  
speed.  
• Never allow water or other liq-  
uids come in contact with  
electrical/electronic compo-  
nents inside the vehicle as  
this may damage them.  
Insects, tar, tree sap, bird droppings,  
industrial pollution and similar  
deposits can damage your vehicle’s  
finish if not removed immediately.  
7 63  
ED English 7.qxp 10/8/2007 5:52 PM Page 64  
Maintenance  
Waxing  
Finish damage repair  
CAUTION  
Wax the vehicle when water will no  
longer bead on the paint.  
Deep scratches or stone chips in the  
painted surface must be repaired  
promptly. Exposed metal will quickly  
rust and may develop into a major  
repair expense.  
• Wiping dust or dirt off the  
body with a dry cloth will  
scratch the finish.  
Always wash and dry the vehicle  
before waxing. Use a good quality  
liquid or paste wax, and follow the  
manufacturer’s instructions. Wax all  
metal trim to protect it and to main-  
tain its luster.  
• Do not use steel wool, abra-  
sive cleaners, or strong deter-  
gents containing highly alka-  
line or caustic agents on  
chrome-plated or anodized  
aluminum parts. This may  
result in damage to the pro-  
tective coating and cause dis-  
coloration or paint deteriora-  
tion.  
NOTICE  
If your vehicle is damaged and  
requires any metal repair or  
replacement, be sure the body shop  
applies anti-corrosion materials to  
the parts repaired or replaced.  
Removing oil, tar, and similar materi-  
als with a spot remover will usually  
strip the wax from the finish. Be sure  
to re-wax these areas even if the rest  
of the vehicle does not yet need wax-  
ing.  
7 64  
ED English 7.qxp 10/8/2007 5:52 PM Page 65  
Maintenance  
Bright-metal maintenance  
Underbody maintenance  
WARNING  
To remove road tar and insects, Corrosive materials used for ice and  
use a tar remover, not a scraper or snow removal and dust control may  
other sharp object.  
After washing the vehicle, test  
the brakes while driving slowly  
to see if they have been affected  
by water. If braking performance  
is impaired, dry the brakes by  
applying them lightly while  
maintaining a slow forward  
speed.  
collect on the underbody. If these  
materials are not removed, acceler-  
ated rusting can occur on underbody  
parts such as the fuel lines, frame,  
floor pan and exhaust system, even  
though they have been treated with  
rust protection.  
To protect the surfaces of bright-  
metal parts from corrosion, apply a  
coating of wax or chrome preser-  
vative and rub to a high luster.  
• During winter weather or in coastal  
areas, cover the bright metal parts  
with a heavier coating of wax or  
preservative. If necessary, coat the  
parts with non-corrosive petroleum  
jelly or other protective compound.  
Thoroughly flush the vehicle under-  
body and wheel openings with luke-  
warm or cold water once a month,  
after off-road driving and at the end  
of each winter. Pay special attention  
to these areas because it is difficult  
to see all the mud and dirt. It will do  
more harm than good to wet down  
the road grime without removing it.  
The lower edges of doors, rocker  
panels, and frame members have  
drain holes that should not be  
allowed to clog with dirt; trapped  
water in these areas can cause rust-  
ing.  
7 65  
ED English 7.qxp 10/8/2007 5:52 PM Page 66  
Maintenance  
Aluminum wheel maintenance  
The aluminum wheels are coated  
with a clear protective finish.  
• Do not use any abrasive cleaner,  
polishing compound, solvent, or  
wire brushes on aluminum wheels.  
They may scratch or damage the  
finish.  
• Use only a mild soap or neutral  
detergent, and rinse thoroughly  
with water. Also, be sure to clean  
the wheels after driving on salted  
roads. This helps prevent corro-  
sion.  
• Avoid washing the wheels with  
high-speed car wash brushes.  
• Do not use any acid detergent. It  
may damage and corrode the alu-  
minum wheels coated with a clear  
protective finish.  
7 66  

Related Topics

Popular Owner Manuals