Get Maintenance -> Light bulbs Guide for Kia Rio 4 Door Third Generation (2017-2023)

Maintenance

LIGHT BULBS

Use only bulbs of the specified • Lamp part malfunction due to

wattage.

Bulb replacement precaution

net-work failure

Please keep extra bulbs on hand

with appropriate wattage ratings in

case of emergencies.

The headlamp, taillight, and fog light

may light up when the head lamp

switch is turned ON, and not light up

when the taillight or for light switch is

turned ON. This may be cause by

network failure or vehicle electrical

control system malfunction. If there is

a problem, we recommend the sys-

tem be serviced by an authorized Kia

dealer.

CAUTION - Light replace-

ment

Refer to “Bulb Wattage” in chapter 9.

Be sure to replace the burned-

out bulb with one of the same

wattage rating. Otherwise, it

may cause damage to the fuse

or electric wiring system.

When changing lamps, first turn off

the engine at a safe place, firmly

apply the parking brake and detach

the battery’s negative (-) terminal.

WARNING - Working on

the lights

CAUTION - Headlamp

Lens

• Lamp part malfunction due to elec-

trical control system stabilization

Prior to working on the light,

firmly apply the parking brake,

ensure that the ignition switch

is turned to the LOCK position

and turn off the lights to avoid

sudden movement of the vehi-

cle and burning your fingers or

receiving an electric shock.

To prevent damage, do not

clean the headlamp lens with

chemical solvents or strong

detergents.

A normally functioning lamp may

flicker momentarily. This momentary

occurrence is due to stabilization

function of the vehicle's electrical on

control system. If the lamp soon

returns to normal, the vehicle does

not require service.

However, if the lamp goes out after

the momentary flickering, or the flick-

ering continues, we recommend the

system be serviced by an authorized

Kia dealer.

8 70

Maintenance

If you don’t have the necessary tools,

the correct bulbs and the expertise,

consult an authorized Kia dealer. In

many cases, it is difficult to replace

vehicle light bulbs because other

parts of the vehicle must be removed

before you can get to the bulb.This is

especially true if you have to remove

the headlamp assembly to get to the

bulb(s).

✽

NOTICE

•

If the light bulb or lamp connector

is removed while the lamp is still

on, the fuse box's electronic sys-

tem may log it as a malfunction.

Therefore,

incident may be recorded as

Diagnostic Trouble Code (DTC) in

the fuse box.

It is normal for an operating lamp

to flicker momentarily. This is due

We recommend that the headlight

aiming be adjusted after an accident

or after the headlight assembly is rein-

stalled at an authorized Kia dealer.

a

lamp malfunction

a

✽

NOTICE

You can find moisture inside the lens

of lamps after a car wash or driving

•

in the rain. It is

a

natural event

Removing/installing the headlamp

assembly can result in damage to

the vehicle.

caused by the temperature differ-

ence between the inside and the out-

side of the lamp and does not mean a

problem with its functions. The

moisture inside the lamp would dis-

appear if you drive the vehicle with

the headlamp turned on, however,

the level at which the moisture is

removed may differ depending on

the size / location / condition of the

lamp. If the moisture continues to

stay inside the lamp, we recommend

that you have the vehicle checked by

an authorized Kia dealer.

to

a

stabilization function of the

vehicle’s electronic control device.

If the lamp lights up normally

after momentarily blinking, then

it is functioning as normal.

However, if the lamp continues to

flicker several times or turns off

completely, there may be an error

in the vehicle’s electronic control

device. Please have the vehicle

checked by an authorized Kia

dealer immediately.

If non-genuine parts or substandard

bulbs are used, it may lead to blow-

ing a fuse or other wiring damages.

Do not install extra lamps or LEDs to

the vehicle. If additional lights are

installed, it may lead to lamp mal-

functions and flickering. Additionally,

the fuse box and other wiring may be

damaged.

8 71

Maintenance

(1) Headlamp (Low/High)

(Bulb type)

Light bulb position (Front)

■ Head lamp - Type A

■ D.R.L. Lamp - Type A

(2) Side marker (Bulb type)

(3) Front turn signal lamp/

Position lamp

(4) Front turn signal lamp

(Bulb type)

(5) Headlamp (Low/High)

(Bulb/LED type)

(6) Side marker (LED type)

OSC077021N

OSC078045N

(7) Position lamp (LED type)

or

■ Head lamp - Type B

■ D.R.L. Lamp - Type B

Position lamp/Day time running

lamp (LED type)

(8) Day time running lamp

(Bulb type)

OSC078022N

OSC078046N

8 72

Maintenance

(1) Rear turn signal lamp (Bulb type)

(2) Back up lamp (Bulb type)

(3) Stop and tail lamp (Bulb type)

(4) Tail lamp (Bulb type)

Light bulb position (Rear) (5 Door)

■ Rear combination lamp (5 Door) - Type A

■ License plate lamp (5 Door)

(5) Side marker (Bulb type)

(6) Stop and tail lamp (LED type)

(7) Side marker (LED type)

(8) License plate lamp

(9) High mounted stop lamp

OSC077023N

OSC077025N

■ Rear combination lamp (5 Door) - Type B

■ High mounted stop lamp (5 Door)

OSC077024N

OSC077026N

8 73

Maintenance

(1) Rear turn signal lamp (Bulb type)

(2) Back up lamp (Bulb type)

Light bulb position (Rear) (4 Door)

■ Rear combination lamp (4 Door) - Type A

■ License plate lamp (4 Door)

(3) Stop and tail lamp/Side marker

(Bulb type)

(4) Tail lamp (Bulb type)

(5) Stop lamp (LED type)

(6) Tail lamp (LED type)

(7) Side marker (LED type)

(8) License plate lamp

(9) High mounted stop lamp

OSC077027N

OSC077025N

■ Rear combination lamp (4 Door) - Type B

■ High mounted stop lamp (4 Door)

OSC077028N

OSC077029N

8 74

Maintenance

6. Install a new headlamp bulb and

snap the headlamp bulb retaining

wire into position by aligning the

wire with the groove on the bulb.

Light bulb position (Side)

Headlamp (Low/High beam)

(Bulb type) bulb replacement

(Headlamp Type A)

■ Type A

7. Connect the headlamp bulb sock-

et-connector.

8. Install the headlamp bulb cover by

turning it clockwise.

OYB076047

■ Type B

OYB076049

1. Open the hood.

2. Remove the headlamp bulb cover

by turning it counterclockwise.

3. Disconnect the headlamp bulb

socket-connector.

4. Unsnap the headlamp bulb retain-

ing wire by pressing the end and

pushing it upward.

OYB076048

(1) Side repeater lamp (LED type)

(2) Side repeater lamp (bulb type)

5. Remove the bulb from the head

lamp assembly.

8 75

Maintenance

Headlamp bulb

Side marker (front) (Bulb type)

bulb replacement (Headlamp

Type A)

(Continued)

• Always handle them carefully,

and avoid scratches and abra-

sions. If the bulbs are lit, avoid

contact with liquids. Never

touch the glass with bare

hands. Residual oil may cause

the bulb to overheat and burst

when lit. A bulb should be

operated only when installed

in a headlamp.

• If a bulb becomes damaged or

cracked, replace it immediate-

ly and carefully dispose of it.

OHD076046

OSC078051N

• Wear eye protection when

changing a bulb. Allow the

bulb to cool down before han-

dling it.

WARNING - Halogen

bulbs

1. Open the hood.

2. Remove the bulb-socket from the

headlamp assembly by turning the

bulb-socket counterclockwise until

the tabs on the bulb-socket align

with the slots on the headlamp

assembly.

Handle halogen bulbs with care.

• Halogen bulbs contain pres-

surized gas that will produce

flying pieces of glass if bro-

ken.

(Continued)

3. Remove the bulb from the bulb-

socket by pulling it out.

8 76

Maintenance

4. Insert a new bulb by inserting it

into the bulb-socket.

4. Insert a new bulb by inserting it

into the bulb-socket and rotating it

until it locks into place.

Front turn signal lamp bulb

replacement (Headlamp Type A)

5. Install the socket in the headlamp

assembly by aligning the tabs on

the bulb-socket with the slots in

the assembly. Push the bulb-sock-

et into the headlamp assembly

and turn the socket clockwise.

5. Install the socket in the headlamp

assembly by aligning the tabs on

the bulb-socket with the slots in

the assembly. Push the bulb-sock-

et into the headlamp assembly

and turn the socket clockwise.

OYB076051

1. Open the hood.

2. Remove the bulb-socket from the

headlamp assembly by turning the

bulb-socket counterclockwise until

the tabs on the bulb-socket align

with the slots on the headlamp

assembly.

3. Remove the bulb from the bulb-

socket by pressing it in and rotat-

ing it counterclockwise until the

tabs on the bulb align with the

slots in the bulb-socket. Pull the

bulb out of the bulb-socket

8 77

Maintenance

5. Install a new bulb-socket assem- Headlamp bulb

bly in the headlamp assembly by

aligning the tabs on the bulb-sock-

et with the slots in the headlamp

assembly. Push the bulb-socket

into the headlamp assembly and

turn the bulb-socket clockwise.

Headlamp (Low/High beam)

(Bulb type) bulb replacement

(Headlamp Type B)

6. Install the headlamp bulb cover by

turning it clockwise.

OQL075058

OYB076052

WARNING - Halogen

bulbs

1. Open the hood.

2. Remove the headlamp bulb cover

by turning it counterclockwise.

Handle halogen bulbs with care.

• Halogen bulbs contain pres-

surized gas that will produce

flying pieces of glass if bro-

ken.

3. Disconnect the headlamp bulb

socket-connector.

4. Remove the bulb-socket from the

headlamp assembly by turning the

bulb-socket counterclockwise until

the tabs on the bulb-socket align

with the slots on the headlamp

assembly.

(Continued)

8 78

Maintenance

Headlamp (Low/High beam)

(LED type) bulb replacement

(Headlamp Type B)

Front turn signal lamp bulb

replacement (Headlamp Type B)

(Continued)

• Always handle them carefully,

and avoid scratches and abra-

sions. If the bulbs are lit, avoid

contact with liquids. Never

touch the glass with bare

hands. Residual oil may cause

the bulb to overheat and burst

when lit. A bulb should be

operated only when installed

in a headlamp.

• If a bulb becomes damaged or

cracked, replace it immediate-

ly and carefully dispose of it.

OYB076054

OSC078038

• Wear eye protection when

changing a bulb. Allow the

bulb to cool down before han-

dling it.

1. Open the hood.

If the headlamp (Low/High beam) (1)

does not operate, have the vehicle

checked by an authorized Kia dealer.

2. Remove the headlamp bulb cover

by turning it counterclockwise.

3. Remove the bulb-socket from the

headlamp assembly by turning the

bulb-socket counterclockwise until

the tabs on the bulb-socket align

with the slots on the headlamp

assembly.

8 79

Maintenance

4. Remove the bulb from the bulb

socket by pressing it in and rotat-

ing it counterclockwise until the

tabs on the bulb align with the

slots in the bulb-socket. Pull the

bulb out of the bulb-socket

Side marker (front) (LED type)

bulb replacement (Headlamp

Type B)

Position lamp + DRL (LED

type) bulb replacement

5. Insert a new bulb by inserting it

into the bulb-socket and rotating it

until it locks into place.

6. Install the socket in the headlamp

assembly by aligning the tabs on

the bulb-socket with the slots in

the assembly. Push the bulb-sock

et into the headlamp assembly

and turn the socket clockwise.

OSC077037N

OSC078053N

If the position lamp + DRL (LED) (1)

does not operate, have the vehicle

checked by an authorized Kia dealer.

7. Install the headlamp bulb cover by

turning it clockwise.

If the Side marker (LED) (1) does not

operate, have the vehicle checked by

an authorized Kia dealer.

The LED lamps cannot be replaced

as a single component because it is

part of an integrated unit. The LED

lamps have to be replaced with the

unit.

The LED lamps cannot be replaced

as a single component because it is

part of an integrated unit. The LED

lamps have to be replaced with the

unit.

A skilled technician should check or

repair the position lamp + DRL

(LED), for it may damage related

parts of the vehicle.

A skilled technician should check or

repair the Side marker (LED), for it

may damage related parts of the

vehicle.

8 80

Maintenance

A skilled technician should check or

repair the DRL bulb, for it may dam-

age related parts of the vehicle.

Daytime running lamp (Bulb

type) bulb replacement

Side repeater lamp (LED type)

bulb Replacement

■ Type A

OYB076057

■ Type B

OYB076047

If the side repeater lamp (LED) (1)

does not operate, have the vehicle

checked by an authorized Kia dealer.

The LED lamps cannot be replaced

as a single component because it is

part of an integrated unit. The LED

lamps have to be replaced with the

unit.

OYB076058

A skilled technician should check or

repair the side repeater lamp (LED),

for it may damage related parts of

the vehicle.

If the DRL (1) does not operate, have

the vehicle checked by an authorized

Kia dealer.

8 81

Maintenance

4. Remove the bulb by pulling it

straight out.

Side repeater lamp (bulb type)

bulb Replacement

Stop and tail lamp bulb

replacement (for 5 door)

5. Insert a new bulb in the socket.

6. Reassemble the socket and the

lens part.

7. Connect the bulb electrical con-

nector.

8. Reinstall the lamp assembly to the

body of the vehicle.

OYB076059

OYB076060

1. Remove the lamp assembly from

the vehicle by prying the lens and

pulling the assembly out.

1. Open the trunk lid.

2. Loosen the light assembly retain-

ing screws with a cross-tip screw-

driver.

2. Disconnect the bulb electrical con-

nector.

3. Separate the socket and the lens

parts by turning the socket coun-

terclockwise until the tabs on the

socket align with the slots on the

lens part.

8 82

Maintenance

8. Install the socket in the assembly

by aligning the tabs on the socket

with the slots in the assembly.

Push the socket into the assembly

and turn the socket clockwise.

9. Install the rear combination lamp

assembly to the body of the vehi-

cle.

OYB076061

OYB076062

3. Remove the rear combination 5. Remove the socket from the

lamp assembly from the body of

the vehicle.

assembly by turning the socket

counterclockwise until the tabs on

the socket align with the slots on

the assembly.

4. Disconnect the rear combination

lamp connector.

6. Remove the bulb from the socket by

pressing it in and rotating it counter-

clockwise until the tabs on the bulb

align with the slots in the socket.

Pull the bulb out of the socket.

7. Insert a new bulb by inserting it

into the socket and rotating it until

it locks into place.

8 83

Maintenance

Rear turn signal lamp bulb

replacement (for 5 door)

OYB076061

OYB076063

3. Remove the rear combination 5. Remove the socket from the

lamp assembly from the body of

the vehicle.

assembly by turning the socket

counterclockwise until the tabs on

the socket align with the slots on

the assembly.

OYB076060

1. Open the trunk lid.

4. Disconnect the rear combination

lamp connector.

2. Loosen the light assembly retain-

ing screws with a cross-tip screw-

driver.

6. Remove the bulb from the socket by

pressing it in and rotating it counter-

clockwise until the tabs on the bulb

align with the slots in the socket.

Pull the bulb out of the socket.

7. Insert a new bulb by inserting it

into the socket and rotating it until

it locks into place.

8 84

Maintenance

8. Install the socket in the assembly

by aligning the tabs on the socket

with the slots in the assembly.

Push the socket into the assembly

and turn the socket clockwise.

Stop and tail lamp (LED type)

bulb replacement (for 5 door)

Back-up lamp bulb replace-

ment (for 5 door)

9. Install the rear combination lamp

assembly to the body of the vehi-

cle.

OYB076064

OYB076065

If the stop and tail lamp (LED) (1) 1. Open the liftgate.

does not operate, have the vehicle

checked by an authorized Kia dealer.

2. Remove the service cover.

The LED lamps cannot be replaced

as a single component because it is

part of an integrated unit. The LED

lamps have to be replaced with the

unit.

A skilled technician should check or

repair the stop and tail lamp (LED),

for it may damage related parts of

the vehicle.

8 85

Maintenance

Tail lamp (inside) bulb replace-

ment (for 5 door)

OYB076066

OYB076067

3. Remove the socket from the

assembly by turning the socket

counterclockwise until the tabs on

the socket align with the slots on

the assembly.

3. Remove the socket from the

assembly by turning the socket

counterclockwise until the tabs on

the socket align with the slots on

the assembly.

OYB076065

1. Open the liftgate.

2. Remove the service cover.

4. Remove the bulb from bulb-socket

by pulling it out.

4. Remove the bulb from bulb-socket

by pulling it out.

5. Insert a new bulb by inserting it

into the bulb-socket.

5. Insert a new bulb by inserting it

into the bulb-socket.

6. Install the socket in the assembly

by aligning the tabs on the socket

with the slots in the assembly.

Push the socket into the assembly

and turn the socket clockwise.

6. Install the socket in the assembly

by aligning the tabs on the socket

with the slots in the assembly.

Push the socket into the assembly

and turn the socket clockwise.

7. Install the service cover by putting

it into the service hole.

7. Install the service cover by putting

it into the service hole.

8 86

Maintenance

Side marker (rear) (Bulb type)

bulb replacement (Rear combi-

nation lampType A) (for 5 door)

OYB076061

OSC078052N

4. Remove the rear combination 6. Remove the socket from the

lamp assembly from the body of

the vehicle.

assembly by turning the socket

counterclockwise until the tabs on

the socket align with the slots on

the assembly.

OYB076060

5. Disconnect the rear combination

lamp connector.

1. Open the liftgate.

2. Remove the service cover.

7. Remove the bulb from bulb-socket

by pulling it out.

3. Loosen the light assembly retain-

ing screws with a cross-tip screw-

driver.

8. Insert a new bulb by inserting it

into the bulb-socket.

9. Install the socket in the assembly

by aligning the tabs on the socket

with the slots in the assembly.

Push the socket into the assembly

and turn the socket clockwise.

8 87

Maintenance

10. Connect the rear combination

lamp connector.

Side marker (rear) (LED type)

bulb replacement (Rear combi-

nation lampType B) (for 5 door)

High mounted stop lamp bulb

replacement (for 5 door)

11. Install the rear combination lamp

assembly to the body of the vehi-

cle.

12. Install the service cover.

OYB076089

OSC078024N

If the high mounted stop lamp (1)

does not operate, have the vehicle

checked by an authorized Kia dealer.

If the Side marker (LED) (1) does not

operate, have the vehicle checked by

an authorized Kia dealer.

A skilled technician should check or

repair the high mounted stop lamp,

for it may damage related parts of

the vehicle.

The LED lamps cannot be replaced

as a single component because it is

part of an integrated unit. The LED

lamps have to be replaced with the

unit.

A skilled technician should check or

repair the Side marker (LED), for it

may damage related parts of the

vehicle.

8 88

Maintenance

3. Remove the bulb from bulb-socket

by pulling it out.

License plate lamp bulb

replacement

Rear turn signal lamp bulb

replacement (for 4 door)

4. Insert a new bulb by inserting it

into the bulb-socket.

5. Install the socket in the assembly

by aligning the tabs on the socket

with the slots in the assembly.

Push the socket into the assembly

and turn the socket clockwise.

6. Align the lens cover tabs with the

lamp housing notches and snap

the lens into place.

OYB076069

OSC077030N

1. Open the trunk lid.

1. Using a flat-blade screwdriver,

gently pry the lens cover from

lamp housing.

2. Remove the service cover by

pulling out the service cover.

2. Remove the socket from the

assembly by turning the socket

counterclockwise until the tabs on

the socket align with the slots on

the assembly.

8 89

Maintenance

6. Install the socket in the assembly

by aligning the tabs on the socket

with the slots in the assembly.

Push the socket into the assembly

and turn the socket clockwise.

Stop and tail lamp / Side mark-

er (Bulb type) replacement

(for 4 door)

7. Install the service cover.

OSC077031N

3. Remove the socket from the

assembly by turning the socket

counterclockwise until the tabs on

the socket align with the slots on

the assembly.

OSC077030N

1. Open the trunk lid.

2. Remove the service cover by

pulling out the service cover.

4. Remove the bulb from the socket

by pressing it in and rotating it

counterclockwise until the tabs on

the bulb align with the slots in the

socket. Pull the bulb out of the

socket.

5. Insert a new bulb by inserting it

into the socket and rotating it until

it locks into place.

8 90

Maintenance

6. Install the socket in the assembly

by aligning the tabs on the socket

with the slots in the assembly.

Push the socket into the assembly

and turn the socket clockwise.

Side marker (rear) (LED type)

bulb replacement (Rear combi-

nation lampType B) (for 4 door)

7. Install the service cover.

OSC077032N

3. Remove the socket from the

assembly by turning the socket

counterclockwise until the tabs on

the socket align with the slots on

the assembly.

OSC078028N

If the Side marker (LED) (1) does not

operate, have the vehicle checked by

an authorized Kia dealer.

4. Remove the bulb from the socket

by pressing it in and rotating it

counterclockwise until the tabs on

the bulb align with the slots in the

socket. Pull the bulb out of the

socket.

The LED lamps cannot be replaced

as a single component because it is

part of an integrated unit. The LED

lamps have to be replaced with the

unit.

5. Insert a new bulb by inserting it

into the socket and rotating it until

it locks into place.

A skilled technician should check or

repair the Side marker (LED), for it

may damage related parts of the

vehicle.

8 91

Maintenance

Back-up lamp bulb replace-

ment (for 4 door)

Tail lamp (Bulb type) bulb

replacement (for 4 door)

OSC077035N

3. Remove the socket from the

assembly by turning the socket

counterclockwise until the tabs on

the socket align with the slots on

the assembly.

OSC077034N

1. Open the trunk lid.

2. Loosen the retaining screw of the

trunk lid cover and then remove

the cover.

2. Loosen the retaining screw of the

trunk lid cover and then remove

the cover.

4. Remove the bulb from bulb-socket

by pulling it out.

5. Insert a new bulb by inserting it

into the bulb-socket.

6. Install the socket in the assembly

by aligning the tabs on the socket

with the slots in the assembly.

Push the socket into the assembly

and turn the socket clockwise.

7. Install the trunk lid cover.

8 92

Maintenance

6. Install the socket in the assembly

by aligning the tabs on the socket

with the slots in the assembly.

Push the socket into the assembly

and turn the socket clockwise.

Stop and tail lamp (LED type)

bulb replacement (for 4 door)

7. Install the trunk lid cover.

OSC077036N

3. Remove the socket from the

assembly by turning the socket

counterclockwise until the tabs on

the socket align with the slots on

the assembly.

OSC077033N

If the stop and tail lamp (LED) (1,2)

does not operate, have the vehicle

checked by an authorized Kia dealer.

4. Remove the bulb from the socket

by pressing it in and rotating it

counterclockwise until the tabs on

the bulb align with the slots in the

socket. Pull the bulb out of the

socket.

The LED lamps cannot be replaced

as a single component because it is

part of an integrated unit. The LED

lamps have to be replaced with the

unit.

A skilled technician should check or

repair the stop and tail lamp (LED),

for it may damage related parts of

the vehicle.

5. Insert a new bulb by inserting it

into the socket and rotating it until

it locks into place.

8 93

Maintenance

4. Insert a new bulb by inserting it

into the bulb-socket.

High mounted stop lamp bulb

replacement (for 4 door)

Trunk lamp bulb replacement

(for 4 door)

5. Install the socket in the housing by

aligning the tabs on the socket

with the slots in the housing. Push

the socket into the housing and

turn the socket clockwise.

OUC076063

OUC076061

1. Open the trunk lid.

1. Using a flat-blade screwdriver,

gently pry the lens cover from

lamp housing.

2. Remove the socket from the hous-

ing by turning the socket counter-

clockwise until the tabs on the

socket align with the slots on the

housing.

2. Remove the bulb by pulling it

straight out.

3. Install a new bulb in the socket.

3. Remove the bulb from bulb-socket

by pulling it out.

4. Align the lens cover tabs with the

lamp housing notches and snap

the lens into place.

8 94

Maintenance

1. Using a flat-blade screwdriver,

gently pry the lamp assembly from

interior.

Map lamp bulb replacement

CAUTION

Be careful not to dirty or dam-

age the lens, lens tab, and plas-

tic housings.

2. Remove the bulb by pulling it

straight out.

3. Install a new bulb in the socket.

4. Install the lamp assembly to interior.

CAUTION

Be careful not to dirty or dam-

age the lens, lens tab, and plas-

tic housings.

OYB076070

WARNING - Interior lamps

Prior to working on the Interior

lamps, ensure that the “OFF”

button is depressed to avoid

burning your fingers or receiv-

ing an electric shock.

8 95

Maintenance

1. Using a flat-blade screwdriver,

gently pry the lamp assembly from

interior.

Vanity mirror lamp bulb

replacement

Room lamp bulb replacement

2. Remove the bulb by pulling it

straight out.

3. Install a new bulb in the socket.

4. Install the lamp assembly to interior.

CAUTION

Be careful not to dirty or dam-

age the lens, lens tab, and plas-

tic housings.

OYB076071

OQL075067

WARNING - Interior lamps

Prior to working on the Interior

lamps, ensure that the “OFF”

button is depressed to avoid

burning your fingers or receiv-

ing an electric shock.

Prior to working on the Interior

lamps, ensure that the “OFF”

button is depressed to avoid

burning your fingers or receiv-

ing an electric shock.

8 96

Maintenance

1. Using a flat-blade screwdriver,

gently pry the lens cover from

lamp housing.

Glove box lamp bulb

replacement

CAUTION

Be careful not to dirty or dam-

age the lens, lens tab, and plas-

tic housings.

2. Remove the bulb by pulling it

straight out.

3. Install a new bulb in the socket.

4. Align the lens cover tabs with the

lamp housing notches and snap

the lens into place.

CAUTION

Be careful not to dirty or dam-

age the lens, lens tab, and plas-

tic housings.

OYB076072

1. Using a flat-blade screwdriver,

gently pry the lamp assembly from

interior.

2. Remove the bulb by pulling it

straight out.

3. Install a new bulb in the socket.

4. Install the lamp assembly to interior.

8 97

Maintenance

Liftgate room lamp bulb

replacement (for 5 door)

CAUTION

Be careful not to dirty or dam-

age the lens, lens tab, and plas-

tic housings.

OYB076073

1. Using a flat-blade screwdriver,

gently pry the lens cover from

lamp housing.

2. Remove the bulb by pulling it

straight out.

3. Install a new bulb in the socket.

4. Align the lens cover tabs with the

lamp housing notches and snap

the lens into place.

8 98

Maintenance -> Light bulbs for Your Kia Rio 4 Door Third Generation (2017-2023)

Related Topics

Popular Owner Manuals

Latest Owner Manuals