Get What to do in an emergency Guide for Kia Sportage SUV Fifth Generation (2022-2026)

What to do in an emergency

Road warning

In case of an emergency while

driving

If an emergency situation occurs while

driving, stay calm and take the following

steps.

What to do in an emergency

Road warning

When an emergency situation occurs

while driving or when you park by the

edge of the roadway, you must alert

approaching or passing vehicles to be

careful as they pass. For this, you should

use the hazard warning flasher.

If the vehicle stalls while driving

1. Reduce your speed gradually, keep

ing a straight line.

-

2. Move cautiously off the road to a safe

place.

Hazard warning flasher

The hazard warning flasher serves as a

warning to other drivers to exercise

extreme caution when approaching,

overtaking, or passing your vehicle.

3. Turn on your hazard warning flasher.

4. Try to start the vehicle again. If your

vehicle will not start, contact an

authorized Kia dealer or seek other

qualified assistance.

If the engine stalls at a crossroad

or crossing

僅 If the engine stalls at a crossroad or

crossing, set the shift lever in the N

(Neutral) position and then push the

vehicle to a safe place.

ONQ5051001

It should be used whenever emergency

repairs are being made or when the

vehicle is stopped near the edge of a

roadway.

If you have a flat tire while driv

ing

-

Depress the flasher switch with the

ENGINE START/STOP button in any

position. The flasher switch is located in

the center fascia panel. All turn signal

lights will flash simultaneously.

1. Take your foot off the accelerator

pedal and let the vehicle slow down

while driving straight ahead.

7

Do not apply the brakes immediately

or attempt to pull off the road as this

may cause a loss of control.

僅 The hazard warning flasher operates

whether your vehicle is running or not.

2. When the vehicle has slowed to such

a speed that it is safe to do so, brake

carefully and pull off the road.

僅 The turn signals do not work when the

hazard flasher is on.

僅 Care must be taken when using the

hazard warning flasher while the vehi

cle is being towed.

3. Drive off the road as far as possible

and park on firm level ground.

-

If you are on a divided highway, do

not park in the median area between

the two traffic lanes.

4. When the vehicle is stopped, turn on

your emergency hazard flashers, set

7

3

What to do in an emergency

If the engine will not start

the parking brake and put the trans

mission in P.

-

If the engine will not start

When the engine doesn't start, first

check to see how much fuel there is and

whether the battery is discharged.

5. Have all passengers get out of the

vehicle. Be sure they all get out on the

side of the vehicle that is away from

traffic.

If engine doesn't turn over or

turns over slowly

6. When changing a flat tire, follow the

1. Be sure the shift lever is in N (Neutral)

or P (Park) and the emergency brake

is set.

instruction provided later in this sec

tion.

-

2. Check the battery connections to be

sure they are clean and tight.

3. Turn on the interior light. If the light

dims or goes out when you operate

the starter, the battery is discharged.

4. Check the starter connections to be

sure they are securely tightened.

WARNING

Do not push or pull the vehicle to start it.

This could cause damage to your vehi

-

cle. Refer to "Jump-starting" on page 7-

5.

If engine turns over normally but

does not start

1. Check the fuel level and add fuel if

necessary.

2. With the ENGINE START/STOP button

in the OFF position, check all connec

-

tors at the ignition coils and spark

plugs. Reconnect any that may be dis

-

connected or loose.

3. Check the fuel line in the engine com

-

partment.

4. If the engine still does not start, call an

authorized Kia dealer or seek other

qualified assistance.

7

4

What to do in an emergency

Emergency starting

WARNING

When the vehicle will not start because

of low battery power, you may need to

jump start the vehicle.

Battery

僅 Never attempt to check the electrolyte

level of the battery, as this may cause

the battery to rupture or explode.

Jump-starting

僅 Keep all flames or sparks away from

the battery. The battery produces

hydrogen gas which may explode if

exposed to flame or sparks.

Connect cables in numerical order and

disconnect in reverse order.

If these instructions are not followed

exactly, serious personal injury and

damage to the vehicle may occur! If

you are not sure how to follow this

procedure, seek qualified assistance.

Automobile batteries contain sulfuric

ONQ5051002

Jump-starting can be dangerous if done

incorrectly. Therefore, to avoid harm to

yourself or damage to your vehicle or

battery, follow these jump-starting pro

cedures. If in doubt, we strongly recom

acid. This is poisonous and highly cor

-

rosive. When jump starting, wear pro

tective glasses and be careful not to

get acid on yourself, your clothing or

on the vehicle.

-

mend that you have a competent

technician or towing service jump-start

your vehicle.

僅 Do not attempt to jump start the vehi

cle if the discharged battery is frozen

or if the electrolyte level is low; the

battery may rupture or explode.

-

CAUTION

Use only a 12-volt jumper system. You

can damage a 12-volt starting motor,

ignition system, and other electrical

parts beyond repair by use of a 24- volt

僅 Do not allow the (+) and (-) jumper

cables to touch. It may cause sparks.

7

僅 The battery may rupture or explode

when you jump start with a low or fro

zen battery.

-

power supply (either two 12-volt batter

-

ies in series or a 24-volt motor generator

set).

WARNING

Battery cables

WARNING

Do not connect the jumper cable from

Frozen batteries

the negative terminal of the booster bat

-

Do not attempt to jump start the vehicle

if the discharged battery is frozen, as the

battery may rupture or explode.

tery to the negative terminal of the dis

-

charged battery, directly. This can cause

the discharged battery to overheat and

crack or degrade. Make sure to connect

one end of the jumper cable to the nega

-

tive terminal of the booster battery, and

7

5

What to do in an emergency

Emergency starting

the other end to a metallic point, far

away from the battery.

4. If connected with the other vehicle,

start the vehicle with the booster bat

tery first and let it run at 2,000 rpm

for several minutes.

-

WARNING

5. Start the vehicle with the discharged

battery.

Sulfuric acid risk

Automobile batteries contain sulfuric

acid. When jump starting your vehicle,

be careful not to get sulfuric acid on

yourself, your clothing, or on the vehicle.

6. If the engine starts, disconnect one

end of the negative terminal of the

booster battery (3), then other end of

the positive terminal of the booster

battery (2) and the discharged battery

(1).

This acid is poisonous and highly corro

-

sive.

If the cause of your battery discharging

is not apparent, have your vehicle

checked by an authorized Kia dealer.

Jump-starting

1. Make sure the booster battery is 12-

volt and that its negative terminal is

grounded.

WARNING

Battery cables

If the booster battery is in another

vehicle, do not allow the vehicles to

come in contact.

Do not connect the jumper cable from

the negative terminal of the booster bat

-

tery to the negative terminal of the dis

charged battery. This can cause the

discharged battery to overheat and

crack, releasing battery acid.

-

2. Turn off all unnecessary electrical

loads.

3. Connect the jumper cables in the

exact sequence shown in the illustra

tion.

-

Make sure to connect one end of the

jumper cable to the negative terminal of

the booster battery, and the other end to

1) Connect one end of a jumper cable

to the positive terminal of the dis

-

a metallic point, far away from the bat

-

charged battery (1).

tery.

2) Connect the other end to the posi

-

tive terminal of the booster battery

(2).

3) Proceed to connect one end of the

other jumper cable to the negative

terminal of the booster battery (3),

then the other end to a solid, sta

-

tionary, metallic point away from

the battery (4).

Do not allow the jumper cables to

contact anything except the correct

battery terminals or the correct

ground. Do not lean over the bat

-

tery when making connections.

7

6

What to do in an emergency

If the engine overheats

Push-starting

If the engine overheats

Vehicles equipped with automatic trans

mission cannot be push-started, and

-

If your temperature gauge indicates

overheating, you experience a loss of

power, or hear a loud pinging or knock

only jump starting can be applied. Fol

low the directions in this section for

"Jump-starting" on page 7-5.

-

ing, the engine will probably be too hot.

If this happens, you should:

1. Pull off the road and stop as soon as it

is safe to do so.

WARNING

Tow starting vehicle

2. Shift the gear to P (Park) and set the

parking brake.

Never tow a vehicle to start it.

When the engine starts, the vehicle can

suddenly surge forward and could cause

a collision with the tow vehicle.

3. If the air conditioning is on, turn it off.

4. If engine coolant is running out under

the vehicle or steam is coming out

from underneath the hood, stop the

engine. Do not open the hood until the

coolant has stopped running or the

steaming has stopped.

5. If there is no visible loss of engine

coolant and no steam, leave the

engine running and check to be sure

the engine cooling fan is operating.

1) If the fan is not running, turn the

engine off.

6. Check to see if the water pump drive

belt is missing.

1) If it is not missing, check to see that

it is tight.

7

2) If the drive belt seems to be satis

-

factory, check for coolant leaking

from the radiator, hoses or under

the vehicle. (If the air conditioning

had been in use, it is normal for

cold water to be draining from it

when you stop).

WARNING

Under the hood

While the engine is running, keep

hair, hands and clothing away

7

What to do in an emergency

Tire Pressure Monitoring System (TPMS)

from moving parts, such as the fan and

drive belts, to prevent injury.

Tire Pressure Monitoring Sys

tem (TPMS) (if equipped)

The Tire Pressure Monitoring System

(TPMS) detects the pressure of vehicle's

tires and displays it on the LCD display.

-

7. If the water pump drive belt is broken

or engine coolant is leaking out, stop

the engine immediately and call the

nearest a professional workshop for

assistance. Call an authorized Kia

dealer.

8. If you cannot find the cause of the

overheating, wait until the engine

temperature has returned to normal.

If coolant has been lost, carefully add

coolant to the reservoir to bring the

fluid level in the reservoir up to the

halfway mark.

9. Proceed with caution, keeping alert

for further signs of overheating. If

overheating happens again, call a

professional workshop for assistance.

Call an authorized Kia dealer.

ONQ5051003N_2

1. Low tire pressure telltale/TPMS mal

function indicator

-

2. Low tire pressure position telltale

(Shown on the LCD display)

WARNING

Coolant reservoir cap

Tire Pressure Indicator

Do not remove the engine cool

-

僅 You can check the tire pressure in the

assist mode on the cluster.

ant reservoir cap when the

engine is hot. This may result in

coolant being blown out of the

opening and cause serious burns.

- Refer to "Driving Assist mode" on

page 4-70.

僅 Tire pressure is displayed 1~2 minutes

later after driving.

CAUTION

僅 If tire pressure is not displayed when

僅 Serious loss of coolant indicates there

is a leak in the cooling system and this

the vehicle is stopped, "Drive to dis

play" message displays. After driving,

check the tire pressure.

-

should be checked as soon as possi

-

ble. Have your vehicle checked by an

authorized Kia dealer.

僅 You can change the tire pressure unit

in the user settings mode on the clus

ter.

-

僅 When the engine overheats from low

engine coolant, suddenly adding

engine coolant may cause cracks in

the engine. To prevent damage, add

- psi, kPa (Refer to "User settings

mode" on page 4-71).

engine coolant slowly in small quanti

-

ties.

7

8

What to do in an emergency

Tire Pressure Monitoring System (TPMS)

should stop and check your tires as soon

as possible, and inflate them to the

NOTICE

僅 The tire pressure may change due to

factors such as parking condition,

driving style, and altitude above sea

level.

proper pressure. Driving on a signifi

-

cantly under-inflated tire causes the tire

to overheat and can lead to tire failure.

Under-inflation also reduces fuel effi

-

僅 The tire pressure shown on the dash

-

ciency and tire tread life, and may affect

board may differ from the tire pres

sure measured by tire pressure

gauge.

-

the vehicle's handling and stopping abil

ity.

-

Please note that the TPMS is not a sub

-

僅 Low tire pressure warning may sound

when a tire's pressure unit is equal or

stitute for proper tire maintenance, and

it is the driver's responsibility to maintain

lower than nearby tires. This is a nor

-

correct tire pressure, even if under-infla

-

mal occurrence, which is due to the

tion has not reached the level to trigger

change in tire pressure along with tire

temperature.

illumination of the TPMS low tire pres

sure telltale.

-

Your vehicle has also been equipped

with a TPMS malfunction indicator to

Effective use of TPMS

WARNING

indicate when the system is not operat

ing properly. The TPMS malfunction

indicator is combined with the low tire

pressure telltale. When the system

detects a malfunction, the telltale will

flash for approximately one minute and

then remain continuously illuminated.

This sequence will continue upon subse

quent vehicle start-ups as long as the

-

Over-inflation or under-inflation can

reduce tire life, adversely affect vehicle

handling, and lead to sudden tire failure

that may cause loss of vehicle control

resulting in an accident

-

Each tire, including the spare (if pro

vided), should be checked monthly

-

7

malfunction exists. When the malfunc

-

when cold and inflated to the inflation

pressure recommended by the vehicle

manufacturer on the vehicle placard or

tire inflation pressure label.

tion indicator is illuminated, the system

may not be able to detect or signal low

tire pressure as intended. TPMS mal

-

functions may occur for a variety of rea

-

sons, including the installation of

(If your vehicle has tires of a different

replacement or alternate tires or wheels

on the vehicle that prevent the TPMS

from functioning properly.

size than the size indicated on the vehi

cle placard or tire inflation pressure

label, you should determine the proper

tire inflation pressure for those tires.)

-

Always check the TPMS malfunction tell

tale after replacing one or more tires or

wheels on your vehicle to ensure that

the replacement or alternate tires and

wheels allow the TPMS to continue to

function properly.

-

As an added safety feature, your vehicle

has been equipped with a tire pressure

monitoring system (TPMS) that illumi

-

nates a low tire pressure telltale when

one or more of your tires is significantly

under-inflated. Accordingly, when the

low tire pressure telltale illuminates, you

7

9

What to do in an emergency

Tire Pressure Monitoring System (TPMS)

Then the TPMS malfunction indicator

and the Low Tire Pressure telltale may

turn on and appear after restarting and

about 20 minutes of continuous driving

before you have the low pressure tire

repaired and replaced on the vehicle.

NOTICE

If any of the below happens, have the

system checked by an authorized Kia

dealer.

1. The low tire pressure telltale/TPMS

malfunction indicator does not appear

for 3 seconds when the ENGINE

START/STOP button is turned to the

ON position or engine is running.

In winter or cold weather, the low tire

pressure telltale may appear if the tire

pressure was adjusted to the recom

-

mended tire inflation pressure in warm

weather. It does not mean your TPMS is

malfunctioning because the decreased

2. The TPMS malfunction indicator

remains appear after blinking for

approximately 1 minute.

temperature leads to a proportional low

-

ering of tire pressure.

3. The Low tire pressure position telltale

remains appear.

You should check the tire inflation pres

-

sure and adjust the tires to the recom

-

mended tire inflation pressure when

driving your vehicle in the following con

Low tire pressure telltale

-

ditions.

Low tire pressure position telltale

僅 from a warm area to a cold area

僅 from a cold area to a warm area

When the TPMS warning indicators

appear, one or more of your tires is sig

-

nificantly under-inflated.

僅 the outside temperature is extremely

high or low

When filling tires with more air, condi

-

tions to turn off the low tire pressure tell

-

tale may not be met. This is because a

tire inflator has a margin of error in per

formance. The low tire pressure telltale

will be turned off if the tire pressure is

above the recommended tire inflation

pressure.

-

ONQ5041289L

A: Low tire pressure

If the telltale appears, immediately

reduce your speed, avoid hard cornering

and anticipate increased stopping dis

WARNING

-

tances. You should stop and check your

tires as soon as possible.

Low pressure damage

Do not drive on low pressure tires. Sig

-

Inflate the tires to the proper pressure as

indicated on the vehicle's placard or tire

inflation pressure label located on the

driver's side center pillar outer panel. If

you cannot reach a service station or if

the tire cannot hold the newly added air,

replace the low pressure tire with the

spare tire.

nificantly low tire pressure can cause the

tires to overheat and fail, making the

vehicle unstable, resulting in increased

braking distances and a loss of vehicle

control.

7

10

What to do in an emergency

Tire Pressure Monitoring System (TPMS)

as soon as possible or replace the flat

tire with the spare tire.

Tire Pressure Monitoring System

(TPMS) malfunction indicator

CAUTION

The low tire pressure telltale will appear

after it blinks for approximately one min

ute when there is a problem with the

TPMS.

-

Repair Agents

Never use a puncture-repairing agent

not approved by Kia to repair and/or

inflate a low pressure tire. Sealant that is

not approved by Kia may damage the

tire pressure sensor.

If the system is able to correctly detect

an underinflation warning at the same

time as system failure, it will appear both

the TPMS malfunction and the low tire

pressure position telltales. For example,

if the Front Left sensor fails, the TPMS

malfunction indicator appears, but if the

Front Right, Rear Left, or Rear Right tire

is underinflated, the low tire pressure

position telltales may appear together

with the TPMS malfunction indicator.

Each wheel is equipped with a tire pres

sure sensor mounted inside the tire

behind the valve stem. You must use

TPMS specific wheels. Always have your

tires serviced by an authorized Kia

dealer.

-

Even if you replace the low pressure tire

with the spare tire, the Low Tire Pressure

telltale will remain on until the low pres

sure tire is repaired and placed on the

vehicle.

Have the system checked by an autho

rized Kia dealer as soon as possible to

determine the cause of the problem.

-

僅 The TPMS malfunction indicator may

be appeard if the vehicle is moving

around electric power supply cables

or radios transmitters such as at

After you replace the low pressure tire

with the spare tire, the TPMS malfunc

tion indicator may appear after a few

-

police stations, government and pub

-

minutes. This is because the TPMS sen

sor mounted on the spare wheel is not

yet activated.

-

lic offices, broadcasting stations, mili

tary installations, airports, or

transmitting towers, etc. This can

interfere with normal operation of the

TPMS.

-

7

Once the low pressure tire is inflated

again to the recommended pressure and

installed on the vehicle or the TPMS sen

-

僅 The TPMS malfunction indicator may

appear if the vehicle is equipped with

sor mounted on the replaced spare

wheel is initiated by a professional work

shop, the TPMS malfunction indicator

and the low tire pressure telltale will turn

off within a few minutes of driving.

-

snow chains or some personal elec

-

tronic devices (such as a laptop com

-

puter, mobile charger, remote starter

or navigation) are being used in the

vehicle. This can interfere with normal

operation of the TPMS.

If the indicator has not disappeared after

a few minutes of driving, please visit an

authorized Kia dealer.

If an original mounted tire is replaced

with the spare tire, the TPMS sensor on

the replaced spare wheel should be initi

Tire replacement with TPMS

If you have a flat tire, the Low Tire Pres

sure telltale will come on. Have the flat

tire repaired by an authorized Kia dealer

-

ated and the TPMS sensor on the origi

nal mounted wheel should be

-

7

11

What to do in an emergency

Tire Pressure Monitoring System (TPMS)

deactivated. If the TPMS sensor on the

original mounted wheel located in the

spare tire carrier still activates, the Tire

Pressure Monitoring System may not

operate properly. Have the tire with

TPMS serviced or replaced by an autho

rized Kia dealer.

the system's ability to warn the driver of

low tire pressure conditions and/or

TPMS malfunctions. Tampering with,

modifying, or disabling the Tire Pressure

Monitoring System (TPMS) components

may void the warranty for that portion of

the vehicle.

-

You may not be able to identify a low tire

by simply looking at it. Always use a

This device complies with Indus

try Canada licence-exempt RSS

standard(s).

-

good quality tire pressure gauge to mea

sure the tire's inflation pressure. Please

note that a tire that is hot (from being

-

Operation is subject to the following

conditions:

driven) will have a higher pressure mea

surement than a tire that is cold (from

sitting stationary for at least 3 hours and

driven less than 1 mile (1.6 km) during

that 3 hour period).

-

1. This device may not cause interfer

-

ence, and

2. This device must accept any interfer

-

ence, including interference that may

cause undesired operation of the

device.

Allow the tire to cool before measuring

the inflation pressure. Always be sure

the tire is cold before inflating to the rec

ommended pressure.

-

3. Changes or modifications not

expressly approved by the party

responsible for compliance could void

the user's authority to operate the

device.

A cold tire means the vehicle has been

sitting for 3 hours and driven for less

than 1 mile (1.6 km) in that 3 hour period.

Never use tire sealant if your vehicle is

equipped with a TPMS. The liquid seal

-

ant can damage the tire pressure sen

-

sors.

僅 The TPMS cannot alert you to severe

and sudden tire damage caused by

external factors such as nails or road

debris.

僅 If you feel any vehicle instability,

immediately take your foot off the

accelerator, apply the brakes gradu

-

ally and with light force, and slowly

move to a safe position off the road.

NOTICE

Protecting TPMS

Tampering with, modifying, or disabling

the Tire Pressure Monitoring System

(TPMS) components may interfere with

7

12

What to do in an emergency

If you have a flat tire (with tire mobility kit)

seals most punctures in a passenger car

tire caused by nails or similar objects

and reinflates the tire.

If you have a flat tire (with tire

mobility kit) (if equipped)

For safe operation, carefully read and

follow the instructions in this manual

before use.

After you ensured that the tire is prop

-

erly sealed you can drive cautiously on

the tire (distance up to 200 km (120

miles)) at a max. speed of 80 km/h (50

mph) in order to reach a service station

or tire dealer to have the tire replaced.

It is possible that some tires, especially

with larger punctures or damage to the

sidewall, cannot be sealed completely.

ONQ5051004N

Air pressure loss in the tire may

adversely affect tire performance.

1

Compressor

2

Sealant bottle

For this reason, you should avoid abrupt

steering or other driving maneuvers,

especially if the vehicle is heavily loaded

or if a trailer is in use.

The Tire Mobility Kit is a temporary fix to

the tire and have your vehicle inspected

by an authorized Kia dealer.

CAUTION

The Tire Mobility Kit is not designed or

intended as a permanent tire repair

method and is to be used for one tire

only. This instruction shows you step by

One sealant for one tire

When two or more tires are flat, do not

use the tire mobility kit because the sup

ported one sealant of Tire Mobility Kit is

only used for one flat tire.

-

step how to temporarily seal the punc

-

ture simply and reliably.

Read the section "Notes on the safe use

of the Tire Mobility Kit" on page 7-17.

WARNING

7

WARNING

Do not use the Tire Mobility Kit to repair

punctures in the tire walls. This can

result in an accident due to tire failure.

Do not use the TMK if a tire is severely

damaged by driving run flat or with

insufficient air pressure.

WARNING

Only punctured areas located within the

tread region of the tire can be sealed

using the TMK.

Have your tire repaired as soon as possi

ble. The tire may loose air pressure at

any time after inflating with the Tire

Mobility Kit.

-

Introduction

With the Tire Mobility Kit you stay mobile

even after experiencing a tire puncture.

The system of compressor and sealing

compound effectively and comfortably

7

13

What to do in an emergency

If you have a flat tire (with tire mobility kit)

Components of the Tire Mobility Kit

ONQ5061072

1

Speed-restriction label

2

3

4

5

6

7

8

9

Sealant bottle and label with speed restriction

Filling hose from sealant bottle to wheel

Connectors and cable for the power outlet direct connection

Holder for the sealant bottle

Compressor

ON/OFF switch

Pressure gauge for displaying the tire inflation pressure

Valve for reducing the tire inflation pressure

* Connectors, cable and connection hose are stored in the compressor housing.

* Strictly follow the specified sequence, otherwise the sealant may escape under high

pressure.

7

14

What to do in an emergency

If you have a flat tire (with tire mobility kit)

WARNING

Expired sealant

Do not use the Tire sealant after the

sealant has expired (i.e. past the expira

-

tion date on the sealant container). This

can increase the risk of tire failure.

OCV061011L

3. Ensure that valve on the compressor

is locked.

WARNING

Sealant

僅 Keep out of reach of children.

僅 Avoid contact with eyes.

僅 Do not swallow.

ONQ5051005N

Using the Tire Mobility Kit

CAUTION

4. Unscrew the valve cap from the valve

of the defective tire and screw the fill

-

ing hose of the sealant bottle onto the

tire valve.

Detach the speed restriction label from

the sealant bottle, and place it in a highly

visible place inside the vehicle such as

on the steering wheel to remind the

driver not to drive too fast.

ONQ5051007N

7

CAUTION

Securely install the sealant filling hose

on the valve. If not, sealant may flow

backward, possibly clogging the filling

hose.

ONQ5051127N

1. Shake the sealant bottle.

5. Ensure that the compressor is

switched off, position 0.

6. Connect between compressor and the

vehicle power outlet using the cable

and connectors.

OCV061010L

2. Remove the cap of the sealant bottle

and screw connection hose onto the

connector of the sealant bottle.

7

15

What to do in an emergency

If you have a flat tire (with tire mobility kit)

Distributing the sealant

ONQ5061066

7. Make the ENGINE START/STOP but

-

ONQ5061122N_2

ton position on or ignition switch posi

tion on.

-

僅 Immediately drive approximately

7~10 km (4~6 miles or, about 10 min)

to evenly distribute the sealant in the

tire.

8. Switch on the compressor and let it

run for approximately 5~7 minutes to

fill the sealant up to proper pressure.

(refer to "Tires and wheels" on page 9-

5). The inflation pressure of the tire

after filling is unimportant and will be

checked/corrected later. Be careful

not to overinflate the tire and stay

away from the tire when filling it.

CAUTION

僅 Do not exceed a speed of 80 km/h

(50 mph). If possible, do not fall below

a speed of 20 km/h (12 mph).

While driving, if you experience any

unusual vibration, ride disturbance or

noise, reduce your speed and drive

with caution until you can safely pull

off of the side of the road. Call for

road side service or towing.

When the tire and wheel are dam

-

aged, do not use Tire Mobility Kit for

your safety.

WARNING

When you use the Tire Mobility Kit, the

wheel may be stained by sealant.

Therefore, remove the wheel stained

by sealant and have the vehicle

inspected at a professional workshop.

Have your vehicle inspected by an

authorized Kia dealer.

If the tire pressure is below 180 kPa (26

psi), do not drive the vehicle. The tire

may cause accident.

9. Switch off the compressor.

10.Detach the sealant filling hoses from

the sealant bottle connector and from

the tire valve. After using, leave the

sealant bottle and the compressor

attached together.

僅 Do not connect another vehicle's Tire

Mobility Kit (TMK) to the power outlet

or battery terminal. The unmatched

power requirement between the vehi

cle power outlet and the tire mobility

kit can cause fire or circuit damage

-

Return the TMK to its storage location in

the vehicle.

within the vehicle and the Tire Mobil

ity Kit.

-

WARNING

Carbon monoxide

Do not leave your vehicle running in a

poorly ventilated area for extended peri

ods of time. Carbon monoxide poisoning

and suffocation can occur.

-

7

16

What to do in an emergency

If you have a flat tire (with tire mobility kit)

Please contact the nearest Kia dealer

ship if the tire cannot be made roadwor

thy with the Tire Mobility Kit.

-

Checking the tire inflation pres

sure

-

1. After driving approximately 7~10 km

(4~6 miles or about 10 min), stop at a

safety location.

WARNING

2. Connect the filling hose of the com

pressor directly to the tire valve.

-

The tire inflation pressure must be at

least 180 kPa (26 psi). If it is not, do not

continue driving. Call for road side ser

-

vice or towing.

NOTICE

When reinstalling the repaired or

ONQ5051007N

replaced tire and wheel on the vehicle,

tighten the wheel lug nut to 11~13 kgf·m

(79~94 lbf·ft).

3. Connect between compressor and the

vehicle power outlet using the cable

and connectors.

4. Adjust the tire inflation pressure to the

recommended tire inflation.

Notes on the safe use of the Tire

Mobility Kit

With the ignition switched on, proceed

as follows.

僅 Park your car at the side of the road

so that you can work with the TMK

away from moving traffic. Place your

warning triangle in a prominent place

to make passing vehicles aware of

your location.

僅 To increase the inflation pressure:

Switch on the compressor. To

check the current inflation pressure

setting, briefly switch off the com

-

pressor.

7

僅 To be sure your vehicle will not move,

even when you're on fairly level

ground, always set your parking

brake.

僅 To reduce the inflation pressure:

Turn the valve on the compressor.

WARNING

Do not let the compressor run for more

than 10 minutes, otherwise the device

will overheat and may be damaged.

僅 Only use the TMK for sealing/inflation

passenger car tires. Do not use on

motorcycles, bicycles or any other

type of tires.

僅 Do not remove any foreign objects-

such as nails or screws -that have

penetrated the tire.

CAUTION

If the inflation pressure is not main

-

tained, drive the vehicle a second time,

refer to "Distributing the sealant" on

page 7-16. Then repeat steps 1 to 4.

僅 Before using the TMK, read the pre

-

cautionary advice printed on the seal

ant bottle!

-

Use of the TMK may be ineffectual for

tire damage larger than approximately 4

mm (0.16 of an inch).

僅 Provided the car is outdoors, leave the

engine running. Otherwise operating

7

17

What to do in an emergency

If you have a flat tire (with spare tire)

the compressor may eventually drain

the car battery.

If you have a flat tire (with

spare tire) (if equipped)

If you have a flat tire, you can change

the flat tire to a spare tire using tools.

僅 Never leave the TMK unattended

while it is being used.

僅 Do not leave the compressor running

for more than 10 min. at a time or it

may overheat.

WARNING

Driving on a flat tire will cause perma

-

nent damage to the tire. Re-inflating a

tire after it has been driven on while

severely underinflated or flat may cause

a blowout and a serious crash. Never

attempt to re-inflate a tire that has been

driven on while severely underinflated or

flat. In this case, repair or replace the flat

tire as soon as possible.

僅 Do not use the TMK if the ambient

temperature is below -30°C (-22°F).

僅 When the tire and wheel are dam

-

aged, do not use Tire Mobility Kit for

your safety.

Technical Data

僅 System voltage: DC 12 V

僅 Working voltage: DC 12 V

僅 Amperage rating: max. 15 A

WARNING

Changing a tire can be dangerous. Fol

-

僅 Suitable for use at temperatures: -30

to 70 °C (-22 to 158 °F)

low the instructions in this section when

changing a tire to reduce the risk of seri

ous injury or death.

-

僅 Max. working pressure: 7 bar (101 psi)

僅 Size

- Compressor: 150 x 130 x 60 mm

(5.9 x 5.1 x 2.4 in.)

CAUTION

Be careful as you use the jack handle to

stay clear of the flat end. The flat end

has sharp edges that could cause cuts.

- Sealant bottle: 115.3 x 87.3 ø mm

(4.5 x 3.4 ø in.)

- Compressor weight: 620 g (1.36 lbs)

- Sealant volume: 400 ml (24.4 cu.

in.)

* Sealant and spare parts can be

obtained and replaced at an autho

-

rized vehicle or tire dealer. Empty seal

ant bottles may be disposed of at

-

home. Liquid residue from the sealant

should be disposed of by your vehicle

or tire dealer or in accordance with

local waste disposal regulations.

7

18

What to do in an emergency

If you have a flat tire (with spare tire)

never use the bumpers or any other

part of the vehicle for jacking support.

Jack and tools

僅 The vehicle can roll off the jack caus

-

ing serious injury or death.

僅 Do not go under a vehicle that is sup

-

ported by a jack.

僅 Do not start or run the engine while

the vehicle is on the jack.

ONQ5A073006

The jack, jack handle, wheel lug nut

wrench are stored in the luggage com

partment.

僅 Do not allow anyone to remain in the

vehicle while it is on the jack.

-

僅 Make sure any children present are in

a secure place, away from the road

and from the vehicle to be raised with

the jack.

Pull up the luggage box cover to reach

this equipment.

1

Jack handle

Jack

2

3

4

Wheel lug nut wrench

WARNING

Tire jack

Tool for removing wheel cover (if

equipped)

Do not place any portion of your body

under a vehicle that is only supported by

a jack since the vehicle can easily roll off

the jack. Use vehicle support stands.

Jacking instructions

The jack is provided for emergency tire

changing only.

僅 To prevent the jack from "rattling"

while the vehicle is in motion, store it

properly.

WARNING

Changing tires

僅 Follow jacking instructions to reduce

the possibility of personal injury.

Never attempt vehicle repairs in the traf

fic lanes of a public road or highway.

-

7

WARNING

Changing tires

Running vehicle on jack

僅 Never attempt vehicle repairs in the

traffic lanes of a public road or high

way.

-

Do not start or run the engine of the

vehicle while the vehicle is on the jack as

this may cause the vehicle to fall off the

jack.

僅 Always move the vehicle completely

off the road and onto the shoulder

before trying to change a tire. The

jack should be used on firm level

ground. If you cannot find a firm level

To prevent the jack from "rattling" while

the vehicle is in motion, store it properly.

place off the road, call a towing ser

vice company for assistance.

-

NOTICE

Retreaded tires

僅 Be sure to use the correct front and

rear jacking positions on the vehicle;

Substantial design variations and the

age of the retreaded tire casing struc

-

7

19

What to do in an emergency

If you have a flat tire (with spare tire)

ture can limit service life and have nega

tive impact on road safety.

-

僅 Turn the tire hold-down wing bolt

counterclockwise with the jack handle.

Use caution when utilizing the sharp

jack handle.

Removing and storing the spare

tire

Changing tires

WARNING

A vehicle can slip or roll off of a jack

causing serious injury or death to you or

those nearby. Take the following safety

precautions:

僅 Never place any portion of your body

under a vehicle that is supported by a

jack.

僅 Turn the tire hold-down wing bolt

counterclockwise to remove.

僅 Store the tire in the reverse order of

removal.

僅 NEVER attempt to change a tire in the

lane of traffic. ALWAYS move the

vehicle completely off the road on

level, firm ground away from traffic

before trying to change a tire. If you

cannot find a level, firm place off the

僅 To prevent the spare tire and tools

from "rattling" while the vehicle is in

motion, store them properly.

WARNING

road, call a towing service for assis

tance.

-

Touching surface of the luggage room

floor

僅 Be sure to use the jack provided with

the vehicle.

Do not touch the metal surface of the

luggage room floor while the engine is

operating or hot. Doing so could result in

serious bodily injury.

僅 ALWAYS place the jack on the desig

-

nated jacking positions on the vehicle

and NEVER on the bumpers or any

other part of the vehicle for jacking

support.

Turn the engine off and wait until it cools

down or wear gloves to remove the

spare tire from the luggage room.

僅 Do not start or run the engine while

the vehicle is on the jack.

If it is hard to loosen the tire holddown

wing bolt by hand, you can loosen it eas

ily using the jack handle.

-

僅 Do not allow anyone to remain in the

vehicle while it is on the jack.

僅 Keep children away from the road and

the vehicle.

1. Park on a level surface and apply the

parking brake firmly.

ONQ5051130N

僅 Put the jack (1) inside of the tire hold-

down wing bolt.

7

20

What to do in an emergency

If you have a flat tire (with spare tire)

son remain in a vehicle that is being

jacked.

僅 Never allow any part of a person's

body to be under a vehicle that is

being jacked or that is on a jack. Jacks

can be unstable and can fall, leading

to serious injury or death.

ONQ5051018L

2. Shift the gear to P (Park), apply the

parking brake, and turn the engine

OFF.

6. Insert the tool (1, if equipped) into the

hole and pull out the wheel cover.

3. Activate the hazard warning flasher.

4. Remove the wheel lug nut wrench,

jack, jack handle, and spare tire from

the vehicle.

5. Block both the front and rear of wheel

that is diagonally opposite the jack

position.

ONQ5A073007

NOTICE

When removing the wheel cover, if you

use any other tool except the tool (1)

provided, the wheel cover may be dam

aged.

-

ONQ5051141N

7. Loosen the wheel lug nuts counter

-

clockwise one turn each, but do not

remove any nut until the tire has been

raised off the ground.

WARNING

Jack location

7

To reduce the possibility of injury, be

sure to only use the jack provided with

the vehicle in the correct jack position;

never use any other part of the vehicle

for jack support.

ONQ5E051121L

WARNING

8. Place the jack at the front (1) or rear

(2) jacking position closest to the tire

you are changing. Place the jack at

the designated locations under the

frame. The jacking positions are

plates welded to the frame with two

tabs and a raised dot to index with the

jack.

Changing a tire

僅 To prevent vehicle movement while

changing a tire, always set the park

ing brake fully, and always block the

wheel diagonally, opposite the wheel

being changed.

-

僅 We recommend that the wheels of the

vehicle be blocked, and that no per

-

7

21

What to do in an emergency

If you have a flat tire (with spare tire)

seated, then tighten the nuts as much

as possible with your fingers again.

12.Lower the vehicle to the ground by

turning the wheel nut wrench coun

-

terclockwise.

ONQ5A073008

ONQ5051021L_4

Then position the wrench as shown in

the drawing and tighten the lug nuts.

9. Insert the jack handle into the jack

and turn it clockwise, raising the vehi

-

Be sure the socket is seated com

pletely over the nut. Do not stand on

the wrench handle or use an exten

-

cle until the tire just clears the ground.

This measurement is approximately

1.2 inches (30 mm). Before removing

the wheel lug nuts, make sure the

vehicle is stable and that there is no

chance for movement or slippage.

-

sion pipe over the wrench handle. Go

around the wheel tightening every

other nut until they are all tight. Then

double-check each nut for tightness.

After changing wheels, have the sys

-

tem checked by a professional work

-

shop. Have your vehicle inspected by

an authorized Kia dealer.

WARNING

ONQ5051142N

Installing a wheel

10.Loosen the lug nuts and remove them

with your fingers. Slide the wheel off

the studs and lay it flat so it cannot

roll away. To put the wheel on the

hub, pick up the spare tire, line up the

holes with the studs and slide the

wheel onto them.

僅 When you install a wheel, always

remove any corrosion, dirt or foreign

materials present on the mounting

surfaces of the wheel or the surface of

the wheel hub, brake drum or brake

disc that contacts the wheel. Make

sure to secure any fasteners that

attach the rotor to the hub so they do

not interfere with the mounting sur

faces of the wheel. Installing wheels

without correct metal-to-metal con

tact at the wheel mounting surfaces

can cause the lug nuts to loosen and

the wheel to come off while your vehi

cle is in motion, resulting in loss of

If this is difficult, tip the wheel slightly

and get the top hole in the wheel lined

up with the top stud. Then jiggle the

wheel back and forth until the wheel

can be slid over the other studs.

-

11.To reinstall the wheel, hold it on the

studs, put the lug nuts on the studs

and tighten them finger tight. Jiggle

the tire to be sure it is completely

-

7

22

What to do in an emergency

If you have a flat tire (with spare tire)

vehicle control, personal injury or

death.

Note that most lug nuts do not have

metric threads. Be sure to use extreme

care in checking for thread style before

installing aftermarket lug nuts or wheels.

If in doubt, consult an authorized Kia

dealer.

僅 Make sure the wheel makes good

contact with the hub when installed. If

the contact of the mounting surface

between the wheel and hub is not

good, the lug nuts could come loose

and cause the loss of a wheel. Loss of

a wheel may result in loss of control of

the vehicle.

WARNING

Wheel studs

If the studs are damaged, they may lose

their ability to retain the wheel. This

could lead to the loss of the wheel and a

collision resulting in serious injuries.

Wheel nut tightening torque:

Steel wheel & aluminum alloy wheel:

11~13 kgf·m (79~94 lbf·ft)

WARNING

If you have a tire gauge, remove the

valve cap and check the air pressure. If

Never use oil or grease on bolts or nuts

because the nuts might come loose. The

vehicle's wheel could fall off, causing a

crash.

the pressure is lower than recom

-

mended, drive slowly to the nearest ser

vice station and inflate to the correct

-

pressure. If it is too high, adjust it until it

is correct. Always reinstall the valve cap

after checking or adjusting tire pressure.

If the cap is not replaced, air may leak

from the tire. If you lose a valve cap, buy

another and install it as soon as possible.

Important - use of compact

spare tire (if equipped)

Your vehicle is equipped with a

compact spare tire. This compact

spare tire takes up less space

than a regular-size tire. This tire

is smaller than a conventional

After you have changed wheels, always

secure the flat tire in its place and return

the jack and tools to their proper storage

locations.

7

tire and is designed for tempo

rary use only.

-

CAUTION

Reusing lug nuts

僅 The compact spare tire is pro

vided only to get you to the

nearest tire store or repair

facility. Do not driver on the

compact spare longer than

necessary. When driving on a

compact spare, drive more

slowly and carefully than usual.

It may not corner the same as

a full size tire, and it may not

-

Make certain during wheel removal that

the same nuts that were removed are

reinstalled - or, if replaced, that nuts with

metric threads and the same chamfer

configuration are used. Your vehicle has

metric threads on the wheel studs and

nuts. Installation of a non-metric thread

nut on a metric stud will not secure the

wheel to the hub properly and will dam

age the stud so that it must be replaced.

-

7

23

What to do in an emergency

If you have a flat tire (with spare tire)

be as durable. Failure to follow

these instructions can lead to

an accident or to being

stranded.

僅 Ensure that you drive slowly

enough for the road conditions

to avoid all hazards. Any road

hazard, such as a pothole or

debris, could seriously dam

age the compact spare.

-

僅 The operation of this vehicle is

not recommended with more

than one compact spare tire in

use at the same time.

僅 Any continuous road use of

this tire could result in tire fail

-

ure, loss of vehicle control, and

possible personal injury.

WARNING

Spare tire

僅 Do not exceed the vehicle's

maximum load rating or the

load-carrying capacity shown

on the sidewall of the compact

spare tire.

The compact spare tire is for

emergency use only. Do not

operate your vehicle on this com

pact spare at speeds over 80

km/h (50 mph). The original tire

should be repaired or replaced

as soon as possible to avoid fail

ure of the spare, possibly leading

to bodily injury or death.

-

僅 Avoid driving over obstacles.

The compact spare tire diame

-

ter is smaller than the diameter

of a conventional tire and

reduces the ground clearance

approximately 1 inch (25 mm),

which could result in damage

to the vehicle.

The compact spare tire should be

inflated to 420 kPa (60 psi).

NOTICE

僅 Do not take this vehicle

through an automatic vehicle

wash while the compact spare

tire is installed.

Check the inflation pressure after

installing the spare tire. Adjust it

tothe specified pressure, as nec

essary.

-

僅 Do not use the compact spare

tire on any other vehicle

because this tire has been

designed especially for your

vehicle.

When using a compact spare tire,

observe the following precau

tions:

-

僅 Under no circumstances

僅 The compact spare tire's tread

life is shorter than a regular

tire. Inspect your compact

spare tire regularly and replace

worn compact spare tires with

should you exceed 80 km/h

(50 mph); a higher speed

could damage the tire.

7

24

What to do in an emergency

If you have a flat tire (with spare tire)

the same size and design,

mounted on the same wheel.

僅 The compact spare tire should

not be used on any other

wheels, nor should standard

tires, snow tires, wheel covers

or trim rings be used with the

compact spare wheel. If such

use is attempted, damage to

these items or other vehicle

components may occur.

僅 Do not use more than one

compact spare tire at a time.

僅 Do not tow a trailer while the

compact spare tire is installed.

7

25

What to do in an emergency

If you have a flat tire (with spare tire)

Jack label

Type A

ONQ5061123L

Type B

ONQ5061089L

Type C

ONQ5061090L

* The actual Jack label in the vehicle may

differ from the illustration. For more

detailed specifications, refer to the

label attached to the jack.

7

When supporting the vehicle, the base

plate of jack must be vertical under

the lifting point.

8

9

Move the shift position to the P (Park)

position on vehicles.

1

Model Name

2

3

Maximum allowable load

The jack should be used on firm level

ground.

When using the jack, set your parking

brake.

10 Jack manufacturer

4

5

When using the jack, stop the engine.

11 Production date

Do not get under a vehicle that is sup

-

12 Representative company and address

ported by a jack.

6

The designated locations under the

frame

7

26

What to do in an emergency

Towing

to ON position and the rollover sensor

detects the situation as a rollover.

Towing

Towing service

NOTICE

If emergency towing is necessary, have

it done by authorized Kia dealer or a

commercial tow-truck service.

If the EPB does not release normally,

take your vehicle to an authorized Kia

dealer by loading the vehicle on a flat

bed tow truck and have the system

checked.

-

Proper lifting and towing procedures are

necessary to prevent damage to the

vehicle. The use of wheel dollies (1) or

flatbed is recommended.

Towing without wheel dollies

when using a towing service

When towing your vehicle in an emer

-

gency without wheel dollies:

1. Set the ignition switch or ENGINE

START/STOP button to ACC position.

2. Place the shift lever in N (Neutral).

3. Release the parking brake.

2-wheel drive vehicle (front wheel drive)

ONQ5051008_3

7

CAUTION

ONQ5051014N

CAUTION

The AWD vehicle should never be towed

with the wheels on the ground. This can

cause serious damage to the transmis

sion or the AWD system.

Towing gear position

-

Failure to shift to N (Neutral) may cause

internal damage to the vehicle.

WARNING

CAUTION

Side and curtain air bag

僅 If any of the loaded wheels or suspen

-

If your vehicle is equipped with side and

curtain air bag, set the ENGINE START/

STOP button to ACC position when the

vehicle is being towed.

sion components are damaged or the

vehicle is being towed with the front

wheels on the ground, use a towing

dolly under the front wheels.

The side and curtain air bag may deploy

when the ENGINE START/STOP button

7

27

What to do in an emergency

Towing

Contact the fire department when

towing the vehicle.

Emergency towing

Front

ONQ5051014

僅 Do not tow the vehicle backwards

with the front wheels on the ground,

as this may cause damage to the

transmission.

2-wheel drive vehicle (front wheel drive)

ONQ5051011

Rear

ONQ5051009

僅 Attaching straps to the chassis, sus

-

ONQ5051010

pension or other parts of the body can

cause damage.

If towing is necessary, have it done by

an authorized Kia dealer or a commer

cial tow truck service.

-

僅 Do not tow with sling-type equipment.

Use wheel lift or flatbed equipment.

If a towing service is not available in an

emergency, your vehicle may be tempo

rarily towed using a cable or chain

secured to the emergency towing hook

at the front (or rear) of the vehicle.

僅 Do not tow the vehicle with four

wheels in contact with the ground if it

-

is the vehicle equipped with Auto

matic Transmission. Otherwise, the

transmission will be seriously dam

aged. Also, make sure not to tow the

-

Use extreme caution when towing the

vehicle with a cable or chain. A driver

must be in the vehicle to steer it and

operate the brakes.

vehicle connecting it with other vehi

-

cles including camper vans.

Towing in this manner may be done only

WARNING

on hard-surfaced roads for a short dis

-

tance and at low speeds. Also, the

wheels, axles, power train, steering and

brakes must all be in good condition.

僅 If you tow the vehicle while the front

wheels are touching the ground, the

vehicle motor may generate electricity

and the motor components may be

damaged or a fire may occur.

CAUTION

Accelerate or decelerate the vehicle in a

僅 When a vehicle fire occurs due to the

battery, there is a risk of a second fire.

slow and gradual manner while main

-

taining tension on the tow rope or chain

to start or drive the vehicle, otherwise

7

28

What to do in an emergency

Towing

tow hooks and the vehicle may be dam

-

wide) in the middle of the cable or

aged.

chain for easy visibility.

僅 Drive carefully so the towing cable or

chain remains tight during towing.

Always follow these emergency towing

precautions:

僅 Before towing, check the automatic

transmission for fluid leaks under

僅 Place the ignition switch in the ACC

position so the steering wheel is not

locked.

your vehicle. If the automatic trans

-

mission fluid is leaking, flatbed equip

-

僅 Place the shift button in N (Neutral).

僅 Release the parking brake.

ment or a towing dolly must be used.

NOTICE

僅 Depress the brake pedal with more

force than normal as you will have

reduced braking performance.

僅 The driver must be in the vehicle for

steering and braking operations when

the vehicle is towed and passengers

other than the driver must not be

allowed to be on board.

僅 More steering effort will be required

because the power steering system

will be disabled.

僅 To avoid damage to your vehicle and

vehicle components when towing:

僅 Use a vehicle heavier than your own

to tow your vehicle.

- Always pull straight ahead when

using the towing hooks. Do not pull

from the side or at a vertical angle.

僅 The drivers of both vehicles should

communicate with each other fre

-

quently.

- Do not use the towing hooks to pull

a vehicle out of mud, sand or other

conditions from which the vehicle

cannot be driven out under its own

power.

僅 Before emergency towing, check that

the hook is not broken or damaged.

僅 Fasten the towing cable or chain

securely to the hook.

僅 Do not jerk the hook. Apply steady

and even force.

7

- Limit the vehicle speed to (15 km/h)

and drive less than 1 mile (1.5 km)

when towing to avoid serious dam

-

age to the automatic transmission.

ONQ5061124N

僅 Use a towing cable or chain less than

16 feet (5 m) long. Attach a white or

red cloth (about 12 inches (30 cm)

7

29

What to do in an emergency

Towing

僅 Read the tire pressure on the

gauge to know whether the tire

pressure is low or high.

Emergency commodity (if

equipped)

There are some emergency commodi

-

4. Adjust the tire pressures to the speci

fied pressure.

-

ties in the vehicle to help you respond to

the emergency situation.

5. Reinstall the inflation valve cap.

Fire extinguisher

If there is small fire and you know how to

use the fire extinguisher, take the follow

-

ing steps carefully.

1. Pull the pin at the top of the extin

-

guisher.

2. Aim the nozzle toward the base of the

fire.

3. Stand approximately 2.5 m (8 ft) away

from the fire and squeeze the handle

to discharge the extinguisher. If you

release the handle, the discharge will

stop.

4. Sweep the nozzle back and forth at

the base of the fire. After the fire

appears to be out, watch it carefully

since it may re-ignite.

First aid kit

Scissors, bandage and adhesive tape

and etc. in the kit is provided.

Triangle reflector

Place the triangle reflector on the road

to warn oncoming vehicles.

Tire pressure gauge

To check the tire pressure, take the fol

lowing steps;

-

1. Unscrew the inflation valve cap.

2. Press and hold the gauge against the

tire valve.

3. A firm non-leaking push will activate

the gauge.

7

30

What to do in an emergency for Your Kia Sportage SUV Fifth Generation (2022-2026)

Related Topics

Popular Owner Manuals

Latest Owner Manuals