2022-2026 Kia Sportage SUV What to do in an emergency -> If you have a flat tire (with spare tire) User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

What to do in an emergency -> If you have a flat tire (with spare tire) for Your Kia Sportage SUV Fifth Generation (2022-2026)

What to do in an emergency  
If you have a flat tire (with spare tire)  
the compressor may eventually drain  
the car battery.  
If you have a flat tire (with  
spare tire) (if equipped)  
If you have a flat tire, you can change  
the flat tire to a spare tire using tools.  
僅 Never leave the TMK unattended  
while it is being used.  
僅 Do not leave the compressor running  
for more than 10 min. at a time or it  
may overheat.  
WARNING  
Driving on a flat tire will cause perma  
-
nent damage to the tire. Re-inflating a  
tire after it has been driven on while  
severely underinflated or flat may cause  
a blowout and a serious crash. Never  
attempt to re-inflate a tire that has been  
driven on while severely underinflated or  
flat. In this case, repair or replace the flat  
tire as soon as possible.  
僅 Do not use the TMK if the ambient  
temperature is below -30°C (-22°F).  
僅 When the tire and wheel are dam  
-
aged, do not use Tire Mobility Kit for  
your safety.  
Technical Data  
僅 System voltage: DC 12 V  
僅 Working voltage: DC 12 V  
僅 Amperage rating: max. 15 A  
WARNING  
Changing a tire can be dangerous. Fol  
-
僅 Suitable for use at temperatures: -30  
to 70 °C (-22 to 158 °F)  
low the instructions in this section when  
changing a tire to reduce the risk of seri  
ous injury or death.  
-
僅 Max. working pressure: 7 bar (101 psi)  
僅 Size  
- Compressor: 150 x 130 x 60 mm  
(5.9 x 5.1 x 2.4 in.)  
CAUTION  
Be careful as you use the jack handle to  
stay clear of the flat end. The flat end  
has sharp edges that could cause cuts.  
- Sealant bottle: 115.3 x 87.3 ø mm  
(4.5 x 3.4 ø in.)  
- Compressor weight: 620 g (1.36 lbs)  
- Sealant volume: 400 ml (24.4 cu.  
in.)  
* Sealant and spare parts can be  
obtained and replaced at an autho  
-
rized vehicle or tire dealer. Empty seal  
ant bottles may be disposed of at  
-
home. Liquid residue from the sealant  
should be disposed of by your vehicle  
or tire dealer or in accordance with  
local waste disposal regulations.  
7
18  
What to do in an emergency  
If you have a flat tire (with spare tire)  
never use the bumpers or any other  
part of the vehicle for jacking support.  
Jack and tools  
僅 The vehicle can roll off the jack caus  
-
ing serious injury or death.  
僅 Do not go under a vehicle that is sup  
-
ported by a jack.  
僅 Do not start or run the engine while  
the vehicle is on the jack.  
ONQ5A073006  
The jack, jack handle, wheel lug nut  
wrench are stored in the luggage com  
partment.  
僅 Do not allow anyone to remain in the  
vehicle while it is on the jack.  
-
僅 Make sure any children present are in  
a secure place, away from the road  
and from the vehicle to be raised with  
the jack.  
Pull up the luggage box cover to reach  
this equipment.  
1
Jack handle  
Jack  
2
3
4
Wheel lug nut wrench  
WARNING  
Tire jack  
Tool for removing wheel cover (if  
equipped)  
Do not place any portion of your body  
under a vehicle that is only supported by  
a jack since the vehicle can easily roll off  
the jack. Use vehicle support stands.  
Jacking instructions  
The jack is provided for emergency tire  
changing only.  
僅 To prevent the jack from "rattling"  
while the vehicle is in motion, store it  
properly.  
WARNING  
Changing tires  
僅 Follow jacking instructions to reduce  
the possibility of personal injury.  
Never attempt vehicle repairs in the traf  
fic lanes of a public road or highway.  
-
7
WARNING  
WARNING  
Changing tires  
Running vehicle on jack  
僅 Never attempt vehicle repairs in the  
traffic lanes of a public road or high  
way.  
-
Do not start or run the engine of the  
vehicle while the vehicle is on the jack as  
this may cause the vehicle to fall off the  
jack.  
僅 Always move the vehicle completely  
off the road and onto the shoulder  
before trying to change a tire. The  
jack should be used on firm level  
ground. If you cannot find a firm level  
To prevent the jack from "rattling" while  
the vehicle is in motion, store it properly.  
place off the road, call a towing ser  
vice company for assistance.  
-
NOTICE  
Retreaded tires  
僅 Be sure to use the correct front and  
rear jacking positions on the vehicle;  
Substantial design variations and the  
age of the retreaded tire casing struc  
-
7
19  
What to do in an emergency  
If you have a flat tire (with spare tire)  
ture can limit service life and have nega  
tive impact on road safety.  
-
僅 Turn the tire hold-down wing bolt  
counterclockwise with the jack handle.  
Use caution when utilizing the sharp  
jack handle.  
Removing and storing the spare  
tire  
Changing tires  
WARNING  
A vehicle can slip or roll off of a jack  
causing serious injury or death to you or  
those nearby. Take the following safety  
precautions:  
僅 Never place any portion of your body  
under a vehicle that is supported by a  
jack.  
僅 Turn the tire hold-down wing bolt  
counterclockwise to remove.  
僅 Store the tire in the reverse order of  
removal.  
僅 NEVER attempt to change a tire in the  
lane of traffic. ALWAYS move the  
vehicle completely off the road on  
level, firm ground away from traffic  
before trying to change a tire. If you  
cannot find a level, firm place off the  
僅 To prevent the spare tire and tools  
from "rattling" while the vehicle is in  
motion, store them properly.  
WARNING  
road, call a towing service for assis  
tance.  
-
Touching surface of the luggage room  
floor  
僅 Be sure to use the jack provided with  
the vehicle.  
Do not touch the metal surface of the  
luggage room floor while the engine is  
operating or hot. Doing so could result in  
serious bodily injury.  
僅 ALWAYS place the jack on the desig  
-
nated jacking positions on the vehicle  
and NEVER on the bumpers or any  
other part of the vehicle for jacking  
support.  
Turn the engine off and wait until it cools  
down or wear gloves to remove the  
spare tire from the luggage room.  
僅 Do not start or run the engine while  
the vehicle is on the jack.  
If it is hard to loosen the tire holddown  
wing bolt by hand, you can loosen it eas  
ily using the jack handle.  
-
僅 Do not allow anyone to remain in the  
vehicle while it is on the jack.  
僅 Keep children away from the road and  
the vehicle.  
1. Park on a level surface and apply the  
parking brake firmly.  
ONQ5051130N  
僅 Put the jack (1) inside of the tire hold-  
down wing bolt.  
7
20  
What to do in an emergency  
If you have a flat tire (with spare tire)  
son remain in a vehicle that is being  
jacked.  
僅 Never allow any part of a person's  
body to be under a vehicle that is  
being jacked or that is on a jack. Jacks  
can be unstable and can fall, leading  
to serious injury or death.  
ONQ5051018L  
2. Shift the gear to P (Park), apply the  
parking brake, and turn the engine  
OFF.  
6. Insert the tool (1, if equipped) into the  
hole and pull out the wheel cover.  
3. Activate the hazard warning flasher.  
4. Remove the wheel lug nut wrench,  
jack, jack handle, and spare tire from  
the vehicle.  
5. Block both the front and rear of wheel  
that is diagonally opposite the jack  
position.  
ONQ5A073007  
NOTICE  
When removing the wheel cover, if you  
use any other tool except the tool (1)  
provided, the wheel cover may be dam  
aged.  
-
ONQ5051141N  
7. Loosen the wheel lug nuts counter  
-
clockwise one turn each, but do not  
remove any nut until the tire has been  
raised off the ground.  
WARNING  
Jack location  
7
To reduce the possibility of injury, be  
sure to only use the jack provided with  
the vehicle in the correct jack position;  
never use any other part of the vehicle  
for jack support.  
ONQ5E051121L  
WARNING  
8. Place the jack at the front (1) or rear  
(2) jacking position closest to the tire  
you are changing. Place the jack at  
the designated locations under the  
frame. The jacking positions are  
plates welded to the frame with two  
tabs and a raised dot to index with the  
jack.  
Changing a tire  
僅 To prevent vehicle movement while  
changing a tire, always set the park  
ing brake fully, and always block the  
wheel diagonally, opposite the wheel  
being changed.  
-
僅 We recommend that the wheels of the  
vehicle be blocked, and that no per  
-
7
21  
What to do in an emergency  
If you have a flat tire (with spare tire)  
seated, then tighten the nuts as much  
as possible with your fingers again.  
12.Lower the vehicle to the ground by  
turning the wheel nut wrench coun  
-
terclockwise.  
ONQ5A073008  
ONQ5051021L_4  
Then position the wrench as shown in  
the drawing and tighten the lug nuts.  
9. Insert the jack handle into the jack  
and turn it clockwise, raising the vehi  
-
Be sure the socket is seated com  
pletely over the nut. Do not stand on  
the wrench handle or use an exten  
-
cle until the tire just clears the ground.  
This measurement is approximately  
1.2 inches (30 mm). Before removing  
the wheel lug nuts, make sure the  
vehicle is stable and that there is no  
chance for movement or slippage.  
-
sion pipe over the wrench handle. Go  
around the wheel tightening every  
other nut until they are all tight. Then  
double-check each nut for tightness.  
After changing wheels, have the sys  
-
tem checked by a professional work  
-
shop. Have your vehicle inspected by  
an authorized Kia dealer.  
WARNING  
ONQ5051142N  
Installing a wheel  
10.Loosen the lug nuts and remove them  
with your fingers. Slide the wheel off  
the studs and lay it flat so it cannot  
roll away. To put the wheel on the  
hub, pick up the spare tire, line up the  
holes with the studs and slide the  
wheel onto them.  
僅 When you install a wheel, always  
remove any corrosion, dirt or foreign  
materials present on the mounting  
surfaces of the wheel or the surface of  
the wheel hub, brake drum or brake  
disc that contacts the wheel. Make  
sure to secure any fasteners that  
attach the rotor to the hub so they do  
not interfere with the mounting sur  
faces of the wheel. Installing wheels  
without correct metal-to-metal con  
tact at the wheel mounting surfaces  
can cause the lug nuts to loosen and  
the wheel to come off while your vehi  
cle is in motion, resulting in loss of  
If this is difficult, tip the wheel slightly  
and get the top hole in the wheel lined  
up with the top stud. Then jiggle the  
wheel back and forth until the wheel  
can be slid over the other studs.  
-
-
11.To reinstall the wheel, hold it on the  
studs, put the lug nuts on the studs  
and tighten them finger tight. Jiggle  
the tire to be sure it is completely  
-
7
22  
What to do in an emergency  
If you have a flat tire (with spare tire)  
vehicle control, personal injury or  
death.  
Note that most lug nuts do not have  
metric threads. Be sure to use extreme  
care in checking for thread style before  
installing aftermarket lug nuts or wheels.  
If in doubt, consult an authorized Kia  
dealer.  
僅 Make sure the wheel makes good  
contact with the hub when installed. If  
the contact of the mounting surface  
between the wheel and hub is not  
good, the lug nuts could come loose  
and cause the loss of a wheel. Loss of  
a wheel may result in loss of control of  
the vehicle.  
WARNING  
Wheel studs  
If the studs are damaged, they may lose  
their ability to retain the wheel. This  
could lead to the loss of the wheel and a  
collision resulting in serious injuries.  
Wheel nut tightening torque:  
Steel wheel & aluminum alloy wheel:  
11~13 kgf·m (79~94 lbf·ft)  
WARNING  
If you have a tire gauge, remove the  
valve cap and check the air pressure. If  
Never use oil or grease on bolts or nuts  
because the nuts might come loose. The  
vehicle's wheel could fall off, causing a  
crash.  
the pressure is lower than recom  
-
mended, drive slowly to the nearest ser  
vice station and inflate to the correct  
-
pressure. If it is too high, adjust it until it  
is correct. Always reinstall the valve cap  
after checking or adjusting tire pressure.  
If the cap is not replaced, air may leak  
from the tire. If you lose a valve cap, buy  
another and install it as soon as possible.  
Important - use of compact  
spare tire (if equipped)  
Your vehicle is equipped with a  
compact spare tire. This compact  
spare tire takes up less space  
than a regular-size tire. This tire  
is smaller than a conventional  
After you have changed wheels, always  
secure the flat tire in its place and return  
the jack and tools to their proper storage  
locations.  
7
tire and is designed for tempo  
rary use only.  
-
CAUTION  
Reusing lug nuts  
僅 The compact spare tire is pro  
vided only to get you to the  
nearest tire store or repair  
facility. Do not driver on the  
compact spare longer than  
necessary. When driving on a  
compact spare, drive more  
slowly and carefully than usual.  
It may not corner the same as  
a full size tire, and it may not  
-
Make certain during wheel removal that  
the same nuts that were removed are  
reinstalled - or, if replaced, that nuts with  
metric threads and the same chamfer  
configuration are used. Your vehicle has  
metric threads on the wheel studs and  
nuts. Installation of a non-metric thread  
nut on a metric stud will not secure the  
wheel to the hub properly and will dam  
age the stud so that it must be replaced.  
-
7
23  
What to do in an emergency  
If you have a flat tire (with spare tire)  
be as durable. Failure to follow  
these instructions can lead to  
an accident or to being  
stranded.  
僅 Ensure that you drive slowly  
enough for the road conditions  
to avoid all hazards. Any road  
hazard, such as a pothole or  
debris, could seriously dam  
age the compact spare.  
-
僅 The operation of this vehicle is  
not recommended with more  
than one compact spare tire in  
use at the same time.  
僅 Any continuous road use of  
this tire could result in tire fail  
-
ure, loss of vehicle control, and  
possible personal injury.  
WARNING  
Spare tire  
僅 Do not exceed the vehicle's  
maximum load rating or the  
load-carrying capacity shown  
on the sidewall of the compact  
spare tire.  
The compact spare tire is for  
emergency use only. Do not  
operate your vehicle on this com  
pact spare at speeds over 80  
km/h (50 mph). The original tire  
should be repaired or replaced  
as soon as possible to avoid fail  
ure of the spare, possibly leading  
to bodily injury or death.  
-
僅 Avoid driving over obstacles.  
The compact spare tire diame  
-
-
ter is smaller than the diameter  
of a conventional tire and  
reduces the ground clearance  
approximately 1 inch (25 mm),  
which could result in damage  
to the vehicle.  
The compact spare tire should be  
inflated to 420 kPa (60 psi).  
NOTICE  
僅 Do not take this vehicle  
through an automatic vehicle  
wash while the compact spare  
tire is installed.  
Check the inflation pressure after  
installing the spare tire. Adjust it  
tothe specified pressure, as nec  
essary.  
-
僅 Do not use the compact spare  
tire on any other vehicle  
because this tire has been  
designed especially for your  
vehicle.  
When using a compact spare tire,  
observe the following precau  
tions:  
-
僅 Under no circumstances  
僅 The compact spare tire's tread  
life is shorter than a regular  
tire. Inspect your compact  
spare tire regularly and replace  
worn compact spare tires with  
should you exceed 80 km/h  
(50 mph); a higher speed  
could damage the tire.  
7
24  
What to do in an emergency  
If you have a flat tire (with spare tire)  
the same size and design,  
mounted on the same wheel.  
僅 The compact spare tire should  
not be used on any other  
wheels, nor should standard  
tires, snow tires, wheel covers  
or trim rings be used with the  
compact spare wheel. If such  
use is attempted, damage to  
these items or other vehicle  
components may occur.  
僅 Do not use more than one  
compact spare tire at a time.  
僅 Do not tow a trailer while the  
compact spare tire is installed.  
7
7
25  
What to do in an emergency  
If you have a flat tire (with spare tire)  
Jack label  
Type A  
ONQ5061123L  
Type B  
ONQ5061089L  
Type C  
ONQ5061090L  
* The actual Jack label in the vehicle may  
differ from the illustration. For more  
detailed specifications, refer to the  
label attached to the jack.  
7
When supporting the vehicle, the base  
plate of jack must be vertical under  
the lifting point.  
8
9
Move the shift position to the P (Park)  
position on vehicles.  
1
Model Name  
2
3
Maximum allowable load  
The jack should be used on firm level  
ground.  
When using the jack, set your parking  
brake.  
10 Jack manufacturer  
4
5
When using the jack, stop the engine.  
11 Production date  
Do not get under a vehicle that is sup  
-
12 Representative company and address  
ported by a jack.  
6
The designated locations under the  
frame  
7
26  

Related Topics

Popular Owner Manuals