2024-2026 Lexus LBX SUV Before driving -> Opening, closing and locking the doors User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Before driving -> Opening, closing and locking the doors for Your Lexus LBX SUV First Generation (2024-2026)

133
3
3-2. Opening, closing and locking the doors
Before driving
3-2.Open ing, closing and locking the door s
■ Smart entry & start system (vehi-
cles with entry function)
Carry the electronic key to enable this
function.
1 Grip the handle to unlock the
doors.
*
Make sure to touch the sensor on the back
of the handle.
The doors cannot be unlocked for 3 sec-
onds after the doors are locked.
*
: The door unlock settings can be
changed.
2 Touch the lock sensor (the indenta-
tion on the surface of the door han-
dle) to lock all the doors.
Check that the door is securely locked.
■ Wireless remote control
1 Locks all the doors
Check that the door is securely locked.
Press and hold to close the windows.
*
2 Unlocks all the doors
Press and hold to open the windows.
*
*
: These settings must be customized at
any authorized Lexus retailer or Lexus
authorized repairer, or any reliable
repairer.
■ Switching the door unlock function
It is possible to set which doors the entry
function unlocks using the wireless remote
control.
1 Turn the power switch off.
2 When the indicator light on the key sur-
face is not on, press and hold or
for approximately 5 seconds
while pressing and holding .
The setting changes each time an operation
is performed, as shown below. (When
changing the setting continuously, release
the buttons, wait for at least 5 seconds, and
repeat step
2.)
Side doors
The vehicle can be locked and
unlocked using the entry function,
wireless remote control or door
lock switches.
Unlocking and locking the doors
from the outside
134
3-2. Opening, closing and locking the doors
For vehicles with alarm: To prevent unin-
tended triggering of the alarm, unlock the
doors using the wireless remote control
and open and close a door once after the
settings have been changed. (If a door is not
opened within 30 seconds after is
pressed, the doors will be locked again and
the alarm will automatically be set.)
In a case that the alarm is triggered, imme-
diately stop the alarm. (P.87)
■ Impact detection door lock release sys-
tem
If the vehicle is involved in a severe frontal
or rear collision, manual release handle
operation will be enabled for all of the
doors. Depending on the force of the
impact or the type of accident, however, the
system may not operate.
■ Operation signals
The emergency flashers flash to indicate
that the doors have been locked/unlocked.
(Locked: once; Unlocked: twice)
A buzzer sounds to indicate that the win-
dows are operating.
■ Security feature
If a door is not opened within approximately
30 seconds after the vehicle is unlocked,
the security feature automatically locks the
vehicle again.
■ When the door cannot be locked by the
lock sensor on the surface of the door
handle (vehicles with entry function)
When the door cannot be locked even if the
lock sensor on the surface of the door han-
dle is touched by a finger, touch the lock
sensor with the palm.
When gloves are being worn, remove the
gloves.
■ Open door warning buzzer
If an attempt to lock the doors is made when
a door is not fully closed, a buzzer sounds
continuously for 5 seconds. Fully close the
door to stop the buzzer, and lock the vehi-
cle once more.
■ If a symbol indicating one or more doors
are open is shown on the multi-informa-
tion display
The hood or one or more of the doors are
not fully closed. The system also indicates
which doors are not fully closed. If the vehi-
cle reaches a speed of 5 km/h (3 mph), a
buzzer sounds to indicate that the door(s)
are not yet fully closed. Make sure that the
hood and all the doors are closed.
■ Setting the alarm (if equipped)
Locking the doors will set the alarm system.
(P.87)
■ Conditions affecting the operation of
the smart entry & start system or wire-
less remote control
P.151
Multi-information
display/Beep
Unlocking function
(Left-hand drive
vehicles)
(Right-hand drive
vehicles)
Exterior: Beeps 3
times
Holding the driver’s
door handle unlocks
only the driver’s door.
Holding the front pas-
senger door handle
unlocks all the doors.
Exterior: Beeps twice
Holding a front door
handle unlocks all the
doors.
135
3
3-2. Opening, closing and locking the doors
Before driving
■ If the smart entry & start system or the
wireless remote control does not oper-
ate properly
● Use the mechanical key to lock and
unlock the doors. (P.528)
● Replace the key battery with a new one if
it is depleted. (P.474)
■ If the 12-volt battery is discharged
The doors cannot be locked and unlocked
using the smart entry & start system or
wireless remote control. Lock or unlock the
doors using the mechanical key. (P.528)
■ Passenger and rear seat reminder func-
tion
As the first reminder so as not to forget lug-
gage, etc. in the front passenger seat or a
rear seat, when the power switch is turned
off after any of the following conditions are
met, a buzzer will sound and a message will
be displayed on the multi-information dis-
play for approximately 6 seconds.
Also, as the second reminder, when the
doors are locked, a buzzer will sound and
the emergency flashers will flash for a few
seconds, and a message will be displayed
on the multi-information display
The hybrid system is started within approxi-
mately 15 minutes after opening and closing
a rear door or the front passenger’s door.
● A rear door or the front passenger’s door
has been opened and closed after the
hybrid system was started.
The second reminder will not be activated if
a rear door or the front passenger door was
opened before the doors are locked.
When this function is disabled by following
the message displayed on the meters, the
passenger and rear seat reminder will be
off.
This function will be re-enabled when the
hybrid system is turned on.
However, if a front passenger door and rear
door is opened and then closed within
approximately 2 seconds, the passenger
and rear seat reminder function may not
operate.
The passenger and rear seat reminder
function determines that luggage, etc. has
been placed in the front passenger seat or a
rear seat based on opening and closing of
the front passenger door or a rear door.
Therefore, depending on the situation, the
passenger and rear seat reminder function
may not operate and you may still forget
luggage, etc. in the front passenger seat or
a rear seat, or it may operate unnecessarily.
■ Customization
Settings (e.g. unlocking function using a
key) can be changed. (Customizable fea-
tures:P.556)
WARNING
■ To prevent an accident
Observe the following precautions while
driving the vehicle.
Failure to do so may result in a door
opening and an occupant falling out,
resulting in death or serious injury.
● Ensure that all doors are properly
closed and locked.
● Do not press the door opener switch
of the doors while driving.
Be especially careful for the driver’s
door, as the doors may be opened
even if the inside lock buttons are in
locked position.
● Set the rear door child-protector locks
when children are seated in the rear
seats.
■ When opening or closing a door
When closing a door, swing it closed with
slight force applied to it. If you press on
the door by hand to close it, it may not be
closed completely.
Check the surroundings of the vehicle
such as whether the vehicle is on an
incline, whether there is enough space
for a door to open and whether a strong
wind is blowing. When opening or clos-
ing the door, hold the door handle tightly
to prepare for any unpredictable move-
ment.
136
3-2. Opening, closing and locking the doors
■ Door lock switches (to
lock/unlock)
1 Front doors: Locks all the doors
Rear doors: Locks the doors
The indicator comes on.
2 Front doors: Unlocks all the doors
Rear doors: Unlocks the doors
The indicator turns off.
Press the door opener switch of
the door handle to open the door.
Make sure to securely press the door
opener switch on the inner side of the
door handle
■ If the 12-volt vehicle battery is dis-
charged
The doors cannot be locked or unlocked
using the smart entry & start system or
wireless remote control, and the door
opener switches will not operate.
Use the mechanical key to enable/disable
manual release handle operation. By
enabling manual release handle operation,
the door can be opened. (P.531)
WARNING
■ When using the wireless remote con-
trol and operating the power win-
dows
Operate the power window after check-
ing to make sure that there is no possibil-
ity of any passenger having any of their
body parts caught in the window. Also,
do not allow children to operate the
wireless remote control. It is possible for
children and other passengers to get
caught in the power window.
Unlocking and locking the doors
from the inside
A
A
Opening the doors from outside
the vehicle
Opening the doors from inside
the vehicle
A
A
137
3
3-2. Opening, closing and locking the doors
Before driving
Press the front side of the door opener
switch to open the door.
Driver’s door: The door will open even if it
is locked.
When the door is unlocked, the door lock
indicator will turn off.
■ Inside door opener switch operating
conditions
When any of the following conditions are
met:
● The vehicle speed is less than 4 km/h
(2.5 mph) and the parking brake is
engaged
● The vehicle speed is less than 4 km/h
(2.5 mph) and the brake pedal is
depressed
● The shift position is in P
■ When opening a door from inside the
vehicle
If the door is not fully unlatched, press the
door opener switch twice to open the door.
■ Manual release handles inside the vehi-
cle
The door opener switches inside the vehicle
can also be used to manually open the
doors.
A door can be opened through electronic
operation by pressing the door opener
switch, or it can be opened using the door
opener switch as a manual release handle
and pulling it twice.
The door cannot be opened from
inside the vehicle when the lock is set.
1 Unlock
2 Lock
These locks can be set to prevent children
from opening the rear doors. Push down
on each rear door switch to lock both rear
doors.
The following functions can be set or
canceled:
For instructions on customizing, refer to
P.556.
Rear door child-protector lock
A
Automatic door locking and
unlocking systems
Function Operation
Speed linked door
locking function
All doors are auto-
matically locked
when the vehicle
speed is approxi-
mately 20 km/h (12
mph) or higher.
Shift position linked
door locking func-
tion
All doors are auto-
matically locked
when shifting the
shift position out of
P.
138
3-2. Opening, closing and locking the doors
Shift position linked
door unlocking
function
All doors are auto-
matically unlocked
when shifting the
shift position to P.
Driver’s door linked
door unlocking
function
All doors are auto-
matically unlocked
when driver’s door is
opened within
approximately 45
seconds after turn-
ing the power switch
off.
Function Operation
Back door
The back door can be
locked/unlocked and
opened/closed by the following
procedures.
WARNING
Observe the following precautions.
Failure to do so may cause parts of the
body to be caught, resulting in death or
serious injury.
■ Before driving the vehicle
Before driving the vehicle, make sure
that the back door is fully closed. If the
back door is not fully closed, it may open
unexpectedly while driving, causing an
accident.
■ Caution while driving
● Keep the back door closed while driv-
ing.
If the back door is left open, it may hit
nearby objects while driving or lug-
gage may be unexpectedly thrown
out, causing an accident.
In addition, exhaust gases may enter
the vehicle, causing death or a serious
health hazard. Make sure to close the
back door before driving.
● Never let anyone sit in the luggage
compartment. In the event of sudden
braking, sudden swerving or a colli-
sion, they are susceptible to death or
serious injury.
■ When children are in the vehicle
Observe the following precautions.
Failure to do so may result in death or
serious injury.
● Do not allow children to play in the
luggage compartment.
If a child is accidentally locked in the
luggage compartment, they could
have heat exhaustion or other injuries.
139
3
3-2. Opening, closing and locking the doors
Before driving
WARNING
● Do not allow a child to open or close
the back door.
Doing so may cause the back door to
move unexpectedly, or cause the
child’s hands, arms, head, or neck to
be caught by the closing back door.
■ Operating the back door
Observe the following precautions.
Failure to do so may cause parts of the
body to be caught, resulting in death or
serious injury.
● Remove any heavy loads, such as
snow and ice, from the back door
before opening it. Failure to do so may
cause the back door to suddenly shut
again after it is opened.
● When opening or closing the back
door, thoroughly check to make sure
the surrounding area is safe.
● If anyone is in the vicinity, make sure
they are safe and let them know that
the back door is about to open or
close.
● Use caution when opening or closing
the back door in windy weather as it
may move abruptly in strong wind.
● Vehicles without power back door:
The back door may suddenly shut if it is
not opened fully. It is more difficult to
open or close the back door on an
incline than on a level surface, so
beware of the back door unexpectedly
opening or closing by itself. Make sure
that the back door is fully open and
secure before using the luggage com-
partment.
● Vehicles with power back door: The
back door may suddenly shut if it is not
opened fully, while on a steep incline.
Make sure that the back door is
secured before using the luggage
compartment.
● When closing the back door, take
extra care to prevent your fingers, etc.,
from being caught.
● When closing the back door, make
sure to press it lightly on its outer sur-
face. If the back door handle is used to
fully close the back door, it may result
in hands or arms being caught.
● Do not pull on the back door damper
stay (vehicles without power back
door) (P.141) or back door spindle
(vehicles with power back door)
(P.147) to close the back door, and
do not hang on the back door damper
stay (vehicles without power back
door) or back door spindle (vehicles
with power back door).
Doing so may cause hands to be
caught or the back door damper stay
(vehicles without a power back door)
or back door spindle (vehicles with
power back door) to break, causing an
accident.
● If a bicycle carrier or similar heavy
object is attached to the back door, it
may suddenly shut again after being
opened, causing someone’s hands,
arms, head or neck to be caught and
injured. When installing an accessory
part to the back door, using a genuine
Lexus part is recommended.
140
3-2. Opening, closing and locking the doors
■ Smart entry & start system (vehi-
cles with entry function)
Carry the electronic key to enable this
function.
1 Locks all the doors
Check that the door is securely locked.
2 Unlocks all the doors
The doors cannot be unlocked for 3 sec-
onds after the doors are locked.
■ Wireless remote control
P.133
■ Door lock switch
P.136
■ Open
Raise the back door while pressing up
the back door opener switch.
■ Close
Lower the back door using the back
door handle, and make sure to push
the back door down from the outside
to close it.
■ Luggage compartment light
● The luggage compartment light turns on
when the back door is opened.
● If the luggage compartment light is left on
when the power switch is turned off, the
light will go off automatically after 10 min-
utes.
■ If the back door opener is inoperative
The back door can be unlocked from the
inside.
1 Remove the cover.
To prevent damage, cover the tip of the
screwdriver with a rag.
Unlocking and locking the back
door from the outside
Unlocking and locking the back
door from the inside
Opening/closing the back door
(vehicles without power back
door)
141
3
3-2. Opening, closing and locking the doors
Before driving
2 Loosen the screw.
3 Turn the cover.
4 Move the lever.
5 When installing, reverse the steps listed.
■ Opening/closing the back door
using the wireless remote control
Press and hold the switch for approxi-
mately 1 second.
The power back door can be operated
when it is unlocked
*
.
Pressing the switch while the power
back door is opening/closing will stop
the operation.
NOTICE
■ Back door damper stays
The back door is equipped with damper
stays that hold the back door in
place.
Observe the following precautions.
Failure to do so may cause damage to
the back door damper stay resulting
in malfunction.
● Do not attach any foreign objects,
such as stickers, plastic sheets, or
adhesives to the damper stay rod.
● Do not touch the damper stay rod with
gloves or other fabric items.
● Do not attach any accessories other
than genuine Lexus parts to the back
door.
● Do not place your hand on the damper
stay or apply lateral forces to it.
Opening/closing the back door
(vehicles with power back door)
A
A
142
3-2. Opening, closing and locking the doors
Pressing and holding the switch again
for approximately 1 second will oper-
ate the power back door in the oppo-
site direction.
*
: Opening of the power back door when it
is locked can be enabled by a custom-
ized setting. (P.556)
■ Opening/closing the back door
from the inside
Press and hold the switch for approxi-
mately 1 second.
A buzzer will sound and the power back
door will automatically open or close.
However, if the power back door is locked,
it will not open.
Pressing the switch while the power back
door is opening/closing will stop the oper-
ation.
Pressing and holding the switch again for
approximately 1 second will operate the
power back door in the opposite direction.
Left-hand drive vehicles
Right-hand drive vehicles
■ Opening/closing the back door
from the outside
Open
When the back door is unlocked: Press the
back door opener switch.
When the back door is locked: While car-
rying the electronic key on your person,
press the back door opener switch.
A buzzer will sound and the back door will
automatically open.
Pressing the switch while the power back
door is opening/closing will stop the oper-
ation.
Close
Press the switch.
A buzzer sounds and the back door will
automatically close.
Pressing the switch while the back door is
closing will stop the operation.
Pressing the switch again will open the
back door automatically.
143
3
3-2. Opening, closing and locking the doors
Before driving
Close the back door and lock all
doors after moving away from the
back door (close & lock [Walk-
Away] function)
*
*
: This setting can be customized at any
authorized Lexus retailer or Lexus
authorized repairer, or any reliable
repairer.
1 Close all of the doors except the
back door, carrying an electronic
key and press the switch on the
lower part of the back door.
A different buzzer than the normal one will
sound and the close & lock (Walk-Away)
function will go into standby.
2 While the buzzer is sounding, move
away from the back door.
When the sensor detects that you are
away from the back door, the buzzer will
sound. Depending on the direction of mov-
ing away from the back door, the location
and how to hold the electronic key or cir-
cumstances, it may not be detected prop-
erly.
All the doors other than the back door will
be locked, and after the back door is
closed, the back door will also be locked.
When all the doors have been closed and
locked, the buzzer (if equipped) will sound
and the emergency flashers will flash.
The standby state is canceled if you do not
move away from the back door for 30 sec-
onds. To operate the function again, per-
form the procedure again from the
beginning.
If you approach the back door carrying the
electronic key, the back door operation
will stop, all the doors will be unlocked, and
the buzzer (if equipped) will sound and the
emergency flashers will flash.
If the switch is pressed after the back
door operation has stopped, the close &
lock (Walk-Away) function will go into
standby again.
Close the back door and lock all
doors (close & lock function)
Press the switch.
A different buzzer than the normal one will
sound and the power back door will begin
closing automatically. When the power
back door is closed, all of the doors will
lock simultaneously and operation signals
will indicate that all of the doors have been
locked.
If the switch is pressed while the power
back door is closing, the operation will
stop.
Pressing the switch again will open the
power back door automatically.
Vehicles with Double locking system: The
double locking system will not operate at
this time.
144
3-2. Opening, closing and locking the doors
■ Closing the back door using the
back door handle
Lower the back door using the back
door handle, then a buzzer sounds and
the back door automatically closes.
■ Luggage compartment light
● The luggage compartment light turns on
when the back door is opened.
● If the luggage compartment light is left on
when the power switch is turned off, the
light will go off automatically after 10 min-
utes.
■ Power back door operating conditions
With the power back door operations set to
ON, it can automatically open and close for
the following conditions:
● The power back door is unlocked. How-
ever, the power back door will operate if
it is locked, in the following situations:
• When an electronic key is being carried
and the back door opener switch is
pressed
• When opening of the power back door
using the wireless remote control when it
is locked is enabled by a customized set-
ting.
● When the power switch is in ON during
opening operations, the back door
unlocks and operates for any of the fol-
lowing conditions:
• Parking brake is engaged
• The brake pedal is depressed
• The shift position is in P
■ Back door closer
In the event that the back door is left slightly
open, the back door closer will automati-
cally close it to the fully closed position.
Whatever the state of the power switch, the
back door closer operates.
■ Operation of the power back door
● A buzzer sounds to indicate that the back
door is opening/closing.
● When the power back door operations
are OFF, the power back door does not
operate but it can be opened and closed
by hand.
● When the power back door automati-
cally opens, if an abnormality due to peo-
ple or objects is detected, operation will
stop.
■ Back door reserve lock function
This function reserves locking of all doors
beforehand, when the power back door is
open.
When the following procedure is per-
formed, all the doors except the power
back door are locked and then power back
door will also be locked at the same time it
is closed.
1 Close all doors, except the back door.
2 During the power back door closing
operation, lock the doors using the
smart entry & start system (P.140) or
the wireless remote control. (P.129)
A buzzer sounds and the emergency flash-
ers flash to indicate that all the doors have
been closed and locked.
Before leaving the vehicle, make sure that
all the doors are closed and locked. The
doors may not be locked due to the jam
protection function or door lock prevention
145
3
3-2. Opening, closing and locking the doors
Before driving
function.
■ Close & lock function
When the power back door is open, this
function closes the power back door and
then locks all of the doors simultaneously.
When the following procedures are per-
formed and there are no electronic keys for
the vehicle within the vehicle, all of the
doors will lock when the power back door is
completely closed.
1 Close all of the doors except the power
back door.
2 While carrying an electronic key, press
the switch on the lower part of
the power back door (P.142).
A different buzzer than the normal one will
sound and then the power back door will
begin closing automatically. When the
power back door is closed, all of the doors
will lock simultaneously and operation sig-
nals will indicate that all of the doors have
been locked.
The double locking system will not operate
at this time.
■ Situations in which the close & lock
function may not operate properly
In the following situations, the close & lock
function may not operate properly:
● If the switch on the lower part of
the power back door (P.142) is
pressed by a hand which is holding an
electronic key
● If the switch on the lower part of
the power back door (P.142) is
pressed when the electronic key is in a
bag, etc. that is placed on the ground
● If the switch on the lower part of
the power back door (P.142) is
pressed with the electronic key not near
the vehicle.
■ When reconnecting the 12-volt battery
To enable the power back door to operate
properly, close the back door manually.
■ Jam protection function
Sensors are installed in the right and left
sides of the power back door. When the
door is automatically closing and the sen-
sors are pushed due to an object being
clamped, etc., the jam protection function
operates.
From that position the door automatically
moves a little in the opposite direction and
then the function stops.
■ If the back door opener is inoperative
The back door can be unlocked from the
inside.
1 Remove the cover.
To prevent damage, cover the tip of the
screwdriver with a rag.
2 Loosen the screw.
3 Turn the cover.
146
3-2. Opening, closing and locking the doors
4 Move the lever.
5 When installing, reverse the steps listed.
■ Customization
Some functions can be customized. (Cus-
tomizable features: P.556)
WARNING
■ Back door closer
● In the event that the back door is left
slightly open, the back door closer will
automatically close it to the fully closed
position. It takes several seconds
before the back door closer begins to
operate. Be careful not to catch fingers
caught or anything else in the back
door, as this may cause bone fractures
or other serious injuries.
● Be careful not to catch fingers or any-
thing else when using the back door
closer as it still operates when the
power back door system is canceled.
■ Power back door
Observe the following precautions when
operating the power back door.
Failure to do so may cause death or seri-
ous injury.
● Check the safety of the surrounding
area to make sure there are no obsta-
cles or anything that could cause any
of your belongings to get caught.
● If anyone is in the vicinity, make sure
they are safe and let them know that
the back door is about to open or
close
● If the power back door system is dis-
abled, while the back door is operating
automatically, the automatic opera-
tion is stopped. The back door then
has to be operated manually. Take
extra care in this situation, as the back
door may open or close suddenly.
● If the operating conditions of the
power back door (P.144) are no
longer met, a buzzer may sound and
the back door may stop opening or
closing. The back door then has to be
operated manually. Take extra care
when on an incline, as the back door
may open or close abruptly.
● On an incline, the back door may sud-
denly shut after it opens. Make sure
the back door is fully open and secure.
● In the following situations, the power
back door may detect an abnormality
and automatic operation may be
stopped. In this case, the back door
has to be operated manually. Take
extra care in this situation, as the back
door may open or close suddenly.
• When the back door contacts an
obstacle
• When the 12-volt battery voltage sud-
denly drops, such as when the power
switch is turned to ON or the hybrid
system is started during automatic
operation
147
3
3-2. Opening, closing and locking the doors
Before driving
WARNING
● If a bicycle carrier or similar heavy
object is attached to the back door, the
power back door may not operate,
causing itself to malfunction, or the
back door may suddenly shut again
after being opened, causing some-
one’s hands, arms, head or neck to be
caught and injured. When installing an
accessory part to the back door, ask
any authorized Lexus retailer or Lexus
authorized repairer, or any reliable
repairer for details.
■ Jam protection function
Observe the following precautions.
Failure to do so may cause death or seri-
ous injury.
● Never use any part of your body to
intentionally activate the jam protec-
tion function.
● The jam protection function may not
work if something gets caught just
before the back door fully closes. Be
careful not to get fingers caught or
anything else.
● The jam protection function may not
work depending on the shape of the
object that is caught. Be careful not to
catch fingers or anything else.
NOTICE
■ Back door spindles
The back door is equipped with spindles
that hold the back door in place.
Observe the following precautions.
Failure to do so may cause damage to
the back door spindle , resulting in
malfunction.
● Do not attach any foreign objects,
such as stickers, plastic sheets, or
adhesives to the spindle rod.
● Do not touch the spindle rod with
gloves or other fabric items.
● Do not attach any accessories other
than genuine Lexus parts to the power
back door.
● Do not place your hand on the spindle
or apply lateral forces to it.
■ To prevent back door closer malfunc-
tion
● Do not apply excessive force to the
back door while the back door closer
is operating. Applying excessive force
may cause the back door closer to
malfunction.
● If the power back door is opened and
closed repeatedly in a short amount of
time, the back door closer may stop
operating. In this case, manually open
the power back door once and wait for
a while before attempting to close it
again.
A
A
148
3-2. Opening, closing and locking the doors
The power back door system can be
enabled/disabled on the Center Dis-
play. (P.556)
1 Select on the Center Display.
2 Select “Vehicle customise”.
3 Select “Door control”.
4 Select “Power back door”.
5 Select (ON)/
(OFF).
When OFF is selected and the operations
of the power back door is made to stop
from the Center Display, unless it is set to
ON, the operation of the power back door
will not return. (No return in the power
switch operation)
The open position of the power back
door can be adjusted.
1 Stop the back door in the desirable
position. (P.141)
2 Press and hold the power back
door switch on the back door for 2
seconds.
• When the settings are completed,
the buzzer sounds 4 times.
• When opening the back door the
next time, the back door will stop at
that position.
NOTICE
■ To prevent damage to the power
back door
● Make sure that there is no ice between
the back door and frame that would
prevent movement of the back door.
Operating the power back door when
excessive load is present on the back
door may cause a malfunction.
● Do not apply excessive force to the
back door while the power back door
is operating.
● Take care not to damage the sensors
(installed on the right and left edges of
the power back door) (P.145) with a
knife or other sharp object. If the sen-
sor is disconnected, the power back
door will not close automatically.
■ Close & lock function
When closing the power back door
using the close & lock function, a differ-
ent buzzer than the normal one will
sound before the operation begins.
To check that the operation has started
correctly, check that a different buzzer
than the normal one has sounded.
Additionally, when the power back door
is fully closed and locked, operation sig-
nals will indicate that all of the doors have
been locked.
Before leaving the vehicle, make sure
that the operation signals have operated
and that all of the doors are locked.
Canceling the power back door
system (vehicles with power
back door)
Adjusting the open position of
the back door (vehicles with
power back door)
149
3
3-2. Opening, closing and locking the doors
Before driving
■ Returning the back door automatic stop
position to the initial settings
Press and hold the power back door switch
on the back door for 7 seconds.
After the buzzer sounds 4 times, it sounds
twice more. When the power back door
does the opening operation the next time,
the door will open to the initial settings posi-
tion.
■ Antenna location
Antennas outside the cabin (vehicles
with entry function)
Antennas inside the cabin
Antenna outside the luggage compart-
ment (vehicles with entry function)
Smart entry & start system
The following operations can be
performed simply by carrying the
electronic key on your person, for
example in your pocket. The driver
should always carry the electronic
key.
Locking and unlocking the doors
(vehicles with entry function)
(P.133)
Locking and unlocking the back
door (vehicles with entry func-
tion) (P.138)
Starting the hybrid system
(P.191)
A
B
C
150
3-2. Opening, closing and locking the doors
Antennas outside the cabin (vehicles
with Lexus Teammate Advanced Park
remote control function)
■ Effective range (areas within which the
electronic key is detected)
When locking or unlocking the doors
(vehicles with entry function)
The system can be operated when the elec-
tronic key is within about 0.7 m (2.3 ft.) of
either of the outside front door handles and
back door opener switch. (Only the doors
detecting the key can be operated.)
When starting the hybrid system or
changing power switch modes
The system can be operated when the elec-
tronic key is inside the vehicle.
■ If an alarm sounds or a warning message
is displayed
An alarm sounds and warning message dis-
plays shown on the multi-information dis-
play are used to protect against
unexpected accidents or theft of the vehicle
resulting from erroneous operation. When
a warning message is displayed, take
appropriate measures based on the dis-
played message.
When only an alarm sounds, circumstances
and correction procedures are as follows.
● When an exterior alarm sounds once for
5 seconds (vehicles with entry function)
● When an interior alarm pings continu-
ously
■ If “Key Detected in Vehicle” is shown on
the multi-information display
An attempt was made to lock the doors
using the smart entry & start system while
the electronic key was still inside the vehi-
cle. Retrieve the electronic key from the
vehicle and lock the doors again.
■ Battery-saving function (vehicles with
entry function)
The battery-saving function will be acti-
vated in order to prevent the electronic key
battery and the 12-volt battery from being
discharged while the vehicle is not in opera-
tion for a long time.
● In the following situations, the smart entry
& start system may take some time to
unlock the doors.
• The electronic key has been left in an
area of approximately 3.5 m (11.5 ft.) of
the outside of the vehicle for 40 seconds
or longer.
• The smart entry & start system has not
been used for 5 days or longer.
D
A
B
Situation
Correction proce-
dure
An attempt was
made to lock the
vehicle while a door
was open.
Close all of the
doors and lock the
doors again.
Situation
Correction proce-
dure
The power switch
was turned to ACC
while the driver’s
door was open (or
the driver’s door was
opened while the
power switch was in
ACC).
Turn the power
switch to OFF and
close the driver’s
door.
151
3
3-2. Opening, closing and locking the doors
Before driving
● If the smart entry & start system has not
been used for 14 days or longer, the
doors cannot be unlocked at any doors
except the driver’s door. In this case, take
hold of the driver’s door handle, or use
the wireless remote control or the
mechanical key, to unlock the doors.
■ Turning an electronic key to battery-
saving mode
● When battery-saving mode is set, battery
depletion is minimized by stopping the
electronic key from receiving radio
waves.
Press twice while pressing and
holding .
Confirm that the electronic key indicator
flashes 4 times.
While the battery-saving mode is set, the
smart entry & start system cannot be used.
To cancel the function, press any of the
electronic key buttons.
● Electronic keys that will not be used for
long periods of time can be set to the bat-
tery-saving mode in advance.
■ When electronic key function stops
If the position of the electronic key has not
changed for a certain amount of time such
as when the electronic key is left some-
where, the function of the electronic key
stops to reduce depletion of the battery.
In this case, function can automatically be
restored by moving the position of the key
such as by lifting it up.
■ Conditions affecting operation
The smart entry & start system uses weak
radio waves. In the following situations, the
communication between the electronic key
and the vehicle may be affected, preventing
the smart entry & start system, wireless
remote control and immobilizer system
from operating properly.
● When the electronic key battery is
depleted
● Near a TV tower, electric power plant,
gas station, radio station, large display,
airport or other facility that generates
strong radio waves or electrical noise
● When the electronic key is in contact
with, or is covered by the following metal-
lic objects
• Cards to which aluminum foil is attached
• Cigarette boxes that have aluminum foil
inside
• Metallic wallets or bags
• Coins
• Hand warmers made of metal
• Media such as CDs and DVDs
● When other wireless key (that emits
radio waves) is being used nearby
● When carrying the electronic key
together with the following devices that
emit radio waves
• Portable radio, cellular phone, cordless
phone or other wireless communication
devices
• Another electronic key or a wireless key
that emits radio waves
• Personal computers or personal digital
assistants (PDAs)
• Digital audio players
• Portable game systems
● If window tint with a metallic content or
metallic objects are attached to the rear
window
● When the electronic key is placed near a
battery charger or electronic devices
● When the vehicle is parked in a pay park-
ing spot where radio waves are emitted.
If the doors cannot be locked/unlocked
using the smart entry & start system,
lock/unlock the doors by performing any of
the following:
● Bring the electronic key close to either
front door handle and operate the entry
function.
152
3-2. Opening, closing and locking the doors
● Operate the wireless remote control.
If the doors cannot be locked/unlocked
using the above methods, use the mechani-
cal key. (P.528)
If the hybrid system cannot be started using
the smart entry & start system, refer to
P.529.
■ Note for the entry function
● Even when the electronic key is within the
effective range (detection areas), the sys-
tem may not operate properly in the fol-
lowing cases:
• The electronic key is too close to the win-
dow or outside door handle, near the
ground, or in a high place when the doors
are locked or unlocked.
• The electronic key is on the instrument
panel, luggage compartment or floor, or
in the door pockets or glove box when
the hybrid system is started or power
switch modes are changed.
• A person is between the vehicle and
electronic key, blocking radio waves
when the door is unlocked.
● Do not leave the electronic key on top of
the instrument panel or near the door
pockets when exiting the vehicle.
Depending on the radio wave reception
conditions, it may be detected by the
antenna outside the cabin and the doors
will become lockable from the outside,
possibly trapping the electronic key
inside the vehicle.
● As long as the electronic key is within the
effective range, the doors may be locked
or unlocked by anyone. However, only
the doors detecting the electronic key
can be used to unlock the vehicle.
● Even if the electronic key is not inside the
vehicle, it may be possible to start the
hybrid system if the electronic key is near
the window.
● The doors may unlock if a large amount
of water splashes on the door handle,
such as in the rain or in a car wash when
the electronic key is within the effective
range. (The doors will automatically be
locked after approximately 30 seconds if
the doors are not opened and closed.)
● If the wireless remote control is used to
lock the doors when the electronic key is
near the vehicle, there is a possibility that
the door may not be unlocked by the
entry function. (Use the wireless remote
control to unlock the doors.)
● Touching the door lock sensor while
wearing gloves may delay or prevent
lock operation. Remove the gloves and
touch the lock sensor again.
● If the door handle becomes wet while the
electronic key is within the effective
range, the door may lock and unlock
repeatedly. In that case, follow the follow-
ing correction procedures to wash the
vehicle.
• Place the electronic key in a location 2 m
(6 ft.) or more away from the vehicle.
(Take care to ensure that the key is not
stolen.)
• Set the electronic key to battery-saving
mode to disable the smart entry & start
system. (P.151)
● If the electronic key is inside the vehicle
and a door handle becomes wet during a
car wash, a message may be shown on
the multi-information display and a
buzzer will sound outside the vehicle. To
turn off the alarm, lock all the doors.
● The lock sensor may not work properly if
it comes into contact with ice, snow, mud,
etc. Clean the lock sensor and attempt to
operate it again.
● A sudden approach to the effective
range or door handle may prevent the
doors from being unlocked. In this case,
return the door handle to the original
position and check that the doors unlock
before pulling the door handle again.
● If there is another electronic key in the
detection area, it may take slightly longer
to unlock the doors after the door handle
is gripped.
■ When the vehicle is not driven for
extended periods
● To prevent theft of the vehicle, do not
leave the electronic key within 2 m (6 ft.)
of the vehicle.
153
3
3-2. Opening, closing and locking the doors
Before driving
● The smart entry & start system can be
deactivated in advance. (P.560)
● Battery-saving mode can reduce the
power consumption of electronic keys.
(P.151)
■ To operate the system properly
Make sure to carry the electronic key when
operating the system. Do not get the elec-
tronic key too close to the vehicle when
operating the system from the outside of
the vehicle.
Depending on the position and holding
condition of the electronic key, the key may
not be detected correctly and the system
may not operate properly. (The alarm may
go off accidentally, or the door lock preven-
tion may not operate.)
■ If the smart entry & start system does
not operate properly
● Locking and unlocking the doors: Use
the mechanical key. (P.528)
● Starting the hybrid system: P.529
■ Customization
Settings (e.g. smart entry & start system)
can be changed.
(Customizable features: P.556)
If the smart entry & start system has been
deactivated in a customized setting, refer to
the explanations for the following opera-
tions.
● Locking and unlocking the doors: Use
the wireless remote control or mechani-
cal key. (P.129, 528)
● Starting the hybrid system and changing
power switch modes: P.529
● Stopping the hybrid system: P.193
WARNING
■ Caution regarding interference with
electronic devices
● People with implantable cardiac pace-
makers, cardiac resynchronization
therapy-pacemakers or implantable
cardioverter defibrillators should
maintain a reasonable distance
between themselves and the smart
entry & start system antennas.
(P.149)
The radio waves may affect the opera-
tion of such devices. If necessary, the
entry function can be disabled. Ask
any authorized Lexus retailer or Lexus
authorized repairer, or any reliable
repairer for details, such as the fre-
quency of radio waves and timing of
the emitted radio waves. Then, consult
your doctor to see if you should dis-
able the entry function.
● User of any electrical medical device
other than implantable cardiac pace-
makers, cardiac resynchronization
therapy-pacemakers or implantable
cardioverter defibrillators should con-
sult the manufacturer of the device for
information about its operation under
the influence of radio waves.
Radio waves could have unexpected
effects on the operation of such medi-
cal devices.
Ask any authorized Lexus retailer or
Lexus authorized repairer, or any reli-
able repairer for details for disabling the
entry function.

Related Topics

Popular Owner Manuals