2024-2026 Lexus LBX SUV Maintenance and care -> Do-it-yourself maintenance User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Maintenance and care -> Do-it-yourself maintenance for Your Lexus LBX SUV First Generation (2024-2026)

443
6
6-3. Do-it-yourself maintenance
Maintenance and care
6-3.D o-it-your self mainte nance
Do-it-yourself service pre-
cautions
If you perform maintenance by
yourself, be sure to follow the cor-
rect procedure as given in these
sections.
Maintenance
Items Parts and tools
12-volt battery
condition
(P.453)
• Grease
• Conventional wrench
(for terminal clamp
bolts)
Engine/power
control unit
coolant level
(P.451)
• “Toyota Super Long
Life Coolant” or a sim-
ilar high quality eth-
ylene glycol-based
non-silicate, non-
amine, non-nitrite and
non-borate coolant
with long-life hybrid
organic acid technol-
ogy
“Toyota Super Long
Life Coolant” is pre-
mixed with 50% cool-
ant and 50% deion-
ized water.
• Funnel (used only for
adding coolant)
Hybrid battery
(traction bat-
tery) air intake
vent (P.471)
• Vacuum cleaner, etc.
• Phillips screwdriver
Engine oil level
(P.449)
• “Toyota Genuine
Motor Oil” or equiva-
lent
• Rag or paper towel
• Funnel (used only for
adding engine oil)
Fuses
(P.476)
• Fuse with same
amperage rating as
original
Light bulbs
(P.479)
• Bulb with same num-
ber and wattage rat-
ing as original
Radiator and
condenser
(P.452)
−
Tire inflation
pressure
(P.467)
• Tire pressure gauge
• Compressed air
source
Washer fluid
(P.452)
• Water or washer fluid
containing antifreeze
(for winter use)
• Funnel (used only for
adding water or
washer fluid)
WARNING
The engine compartment contains many
mechanisms and fluids that may move
suddenly, become hot, or become elec-
trically energized. To avoid death or seri-
ous injury, observe the following
precautions.
■ When working on the engine com-
partment
● Make sure that “POWER ON” on the
multi-information display and the
“READY” indicator are both off.
Items Parts and tools
444
6-3. Do-it-yourself maintenance
WARNING
● Keep hands, clothing and tools away
from the moving fan and engine drive
belt.
● Be careful not to touch the engine,
power control unit, radiator, exhaust
manifold, etc., right after driving as
they may be hot. Oil and other fluids
may also be hot.
● Do not leave anything that may burn
easily, such as paper and rags, in the
engine compartment.
● Do not smoke, cause sparks or expose
an open flame to fuel. Fuel fumes are
flammable.
● Take care because brake fluid can
harm your hands or eyes and damage
painted surfaces. If fluid gets on your
hands or in your eyes, flush the
affected area with clean water imme-
diately. If you still experience discom-
fort, consult a doctor.
■ When working near the electric cool-
ing fans or radiator grille
Be sure the power switch is OFF.
With the power switch in ON, the elec-
tric cooling fans may automatically start
to run if the air conditioning is on and/or
the coolant temperature is high.
(P.452)
■ Safety glasses
Wear safety glasses to prevent flying or
falling material, fluid spray, etc., from get-
ting in your eyes.
NOTICE
■ If you remove the air cleaner filter
Driving with the air cleaner filter
removed may cause excessive engine
wear due to dirt in the air.
■ If the fluid level is low or high
It is normal for the brake fluid level to go
down slightly as the brake pads wear or
when the fluid level in the accumulator is
high.
If the reservoir needs frequent refilling, it
may indicate a serious problem.
445
6
6-3. Do-it-yourself maintenance
Maintenance and care
1 Pull the hood lock release lever.
The hood will pop up slightly.
2 Pull up the auxiliary catch lever and
lift the hood.
3 Hold the hood open by inserting
the supporting rod into the slot.
Hood
Opening the hood
WARNING
■ Pre-driving check
Check that the hood is fully closed and
locked.
If the hood is not locked properly, it may
open while the vehicle is in motion and
cause an accident, which may result in
death or serious injury.
■ After installing the support rod into
the slot
Make sure the rod is properly inserted
into the slot to prevent the hood from
shutting on your head or body.
NOTICE
■ When closing the hood
Be sure to return the support rod to its
clip before closing the hood. Closing the
hood without returning the support rod
properly may cause the hood to be dam-
aged.
446
6-3. Do-it-yourself maintenance
■ Front
■ Rear
2WD models
AWD models
Positioning a floor jack
When using a floor jack, follow the
instructions in the manual provided
with the jack and perform the oper-
ation safely.
When raising your vehicle with a
floor jack, position the jack cor-
rectly. Improper placement may
damage your vehicle or cause
injury.
Location of the jack point
447
6
6-3. Do-it-yourself maintenance
Maintenance and care
NOTICE
■ When jacking up the rear of the vehi-
cle
Make sure that the jack saddle does not
contact the muffler. If the vehicle is
jacked up with the jack saddle contacting
the muffler, exhaust system parts may
become damaged.
448
6-3. Do-it-yourself maintenance
Fuse boxes (P.476)
Engine oil filler cap (P.450)
Engine coolant radiator cap
Engine coolant reservoir (P.451)
Radiator (P.452)
Condenser (P.452)
Electric cooling fan
Engine oil level dipstick (P.449)
Power control unit coolant reservoir (P.451)
Washer fluid tank (P.452)
■ 12-volt battery
P.453
Engine compartment
Components
A
B
C
D
E
F
G
H
I
J
449
6
6-3. Do-it-yourself maintenance
Maintenance and care
With the engine at operating tempera-
ture and turned off, check the oil level
on the dipstick.
1 Park the vehicle on level ground.
After warming up the engine and
turning off the hybrid system, wait
about 5 minutes for the oil to drain
back into the bottom of the engine.
2 Holding a rag under the end, pull
the dipstick out.
3 Wipe the dipstick clean.
4 Reinsert the dipstick fully.
5 Holding a rag under the end, pull
the dipstick out and check whether
the oil level is above low level mark.
Low level mark
The shape of the dipstick may differ
depending on the type of vehicle or
engine.
6 Wipe the dipstick and reinsert it
fully.
■ Engine oil consumption
A certain amount of engine oil will be con-
sumed while driving. In the following situa-
tions, oil consumption may increase, and
engine oil may need to be refilled in
between oil maintenance intervals.
● When the engine is new, for example
directly after purchasing the vehicle or
after replacing the engine
● If low quality oil or oil of an inappropriate
viscosity is used
● When driving at high engine speeds or
with a heavy load, when towing (vehicles
with towing package), or when driving
while accelerating or decelerating fre-
quently
● When leaving the engine idling for a long
time, or when driving frequently through
heavy traffic
■ Engine oil level rise
If the vehicle is repeatedly driven without
the engine warmed up, moisture caused by
dew condensation inside the engine or fuel
which did not burn mixes into the engine oil,
resulting in a rise in engine oil level. How-
ever, this is not a malfunction.
For example, the engine become difficult to
be warmed up in the following situations.
● When driving a short distance
● When driving at a low speed
● When the outside temperature is low
When checking the engine oil, make sure
that the engine is warmed up. If the engine
oil level exceeds the refill upper limit mark,
contact any authorized Lexus retailer or
Lexus authorized repairer, or any reliable
repairer.
Checking the engine oil
A
NOTICE
■ To prevent serious engine damage
Check the oil level on a regular basis.
450
6-3. Do-it-yourself maintenance
■ Checking the oil type and prepar-
ing the items needed
Make sure to check the oil type and
prepare the items needed before add-
ing oil.
Engine oil selection
P.549
Oil quantity (Low level mark
Refill upper limit mark)
1.2 L (1.3 qt., 1.1 Imp. qt.)
Items
Clean funnel
■ Adding engine oil
If the oil level is below or near the low
level mark, add engine oil of the same
type as that already in the engine.
1 Remove the oil filler cap by turning
it counterclockwise.
2 Add engine oil slowly, checking the
dipstick.
Make sure that the oil level does not
exceed the refill upper limit mark and is
between the low level mark and refill upper
limit mark.
Low level mark
Refill upper limit mark
The shape of the dipstick may differ
depending on the type of vehicle or
engine.
3 Install the oil filler cap by turning it
clockwise.
4 When installing the cover, reverse
the steps listed.
■ After changing the engine oil
After the engine oil has been replaced, the
engine oil maintenance data should be
reset. Perform the following procedures:
1 Select on the Center Display.
2 Select “Vehicle customise”.
3 Select “Utility”.
4 Select “Oil maintenance”.
5 Select “Reset”.
“The data has been reset.” will be displayed
on the Center Display when the reset pro-
cedure has been completed.
Adding engine oil
A
B
451
6
6-3. Do-it-yourself maintenance
Maintenance and care
The coolant level is satisfactory if it is
between the “F” and “L” lines on the
reservoir when the hybrid system is
cold.
■ Engine coolant reservoir
Reservoir cap
“F” line
“L” line
Radiator cap
If the level is on or below the “L” line, add
coolant up to the “F” line. (P.539)
■ Power control unit coolant reser-
voir
Reservoir cap
“F” line
“L” line
If the level is on or below the “L” line, add
coolant up to the “F” line. (P.539)
WARNING
■ Used engine oil
● Used engine oil contains potentially
harmful contaminants which may
cause skin disorders such as inflamma-
tion and skin cancer, so care should be
taken to avoid prolonged and
repeated contact. To remove used
engine oil from your skin, wash thor-
oughly with soap and water.
● Dispose of used oil and filters only in a
safe and acceptable manner. Do not
dispose of used oil and filters in house-
hold trash, in sewers or onto the
ground. Call any authorized Lexus
retailer or Lexus authorized repairer,
or any reliable repairer, service station
or auto parts store for information
concerning recycling or disposal.
● Do not leave used engine oil within the
reach of children.
NOTICE
■ When replacing the engine oil
● Be careful not to spill engine oil on the
vehicle components.
● Avoid overfilling, or the engine could
be damaged.
● Check the oil level on the dipstick
every time you refill the vehicle.
● Be sure the engine oil filler cap is prop-
erly tightened.
■ Precautions when filling engine oil
When lifting up the cover (P.450), lift
slowly to prevent any load from being
applied to the weatherstrip. If strongly
pulled, the weatherstrip may become
damaged.
Checking the coolant
A
B
C
D
A
B
C
452
6-3. Do-it-yourself maintenance
■ Coolant selection
Only use “Toyota Super Long Life Coolant”
or a similar high quality ethylene glycol
based non-silicate, non-amine, non-nitrite,
and non-borate coolant with long-life
hybrid organic acid technology.
“Toyota Super Long Life Coolant” is a mix-
ture of 50% coolant and 50% deionized
water. (Minimum temperature: -35°C [-
31°F])
For more details about coolant, contact any
authorized Lexus retailer or Lexus autho-
rized repairer, or any reliable repairer.
■ If the coolant level drops within a short
time of replenishing
Visually check the radiator, hoses,
engine/power control unit coolant reser-
voir caps, drain cock and water pump.
If you cannot find a leak, have any autho-
rized Lexus retailer or Lexus authorized
repairer, or any reliable repairer, test the
cap and check for leaks in the cooling sys-
tem.
Check the radiator and condenser,
and clear away any foreign objects.
If either of the above parts is extremely
dirty or you are not sure of their condi-
tion, have your vehicle inspected by
any authorized Lexus retailer or Lexus
authorized repairer, or any reliable
repairer.
If the washer fluid level is at “1/2”, add
washer fluid.
WARNING
■ When the hybrid system is hot
Do not remove the engine/power con-
trol unit coolant reservoir caps.
The cooling system may be under pres-
sure and may spray hot coolant if the cap
is removed, causing serious injuries, such
as burns.
NOTICE
■ When adding coolant
Coolant is neither plain water nor
straight antifreeze. The correct mixture
of water and antifreeze must be used to
provide proper lubrication, corrosion
protection and cooling. Be sure to read
the antifreeze or coolant label.
■ If you spill coolant
Be sure to wash it off with water to pre-
vent it from damaging parts or paint.
Checking the radiator and con-
denser
WARNING
■ When the hybrid system is hot
Do not touch the radiator or condenser
as they may be hot and cause serious
injuries, such as burns.
■ When the electric cooling fans are
operating
Do not touch the engine compartment.
The electric cooling fans may keep rotat-
ing for about 3 minutes even after the
power switch is off.
With the power switch in ON, the elec-
tric cooling fans may automatically start
to run if the air conditioning is on and/or
the coolant temperature is high. Be sure
the power switch is OFF when working
near the electric cooling fans or radiator
grille.
Adding the washer fluid
453
6
6-3. Do-it-yourself maintenance
Maintenance and care
The 12-volt battery is located under the
rear right side seat.
■ Before recharging
When recharging, the 12-volt battery pro-
duces hydrogen gas which is flammable
and explosive. Therefore, observe the fol-
lowing precautions before recharging:
● If recharging with the 12-volt battery
installed on the vehicle, be sure to dis-
connect the ground cable.
● Make sure the power switch on the char-
ger is off when connecting and discon-
necting the charger cables to the 12-volt
battery.
■ After recharging/reconnecting the 12-
volt battery
● Vehicles with steering lock system: The
hybrid system may not start. Follow the
procedure below to initialize the system.
1 Shift the shift lever to P.
2 Open and close any of the doors.
3 Restart the hybrid system.
● Unlocking the doors using the smart
entry & start system may not be possible
immediately after reconnecting the 12-
volt battery. If this happens, use the wire-
less remote control or the mechanical
key to lock/unlock the doors.
● Start the hybrid system with the power
switch in ACC
*
. The hybrid system may
WARNING
■ When adding washer fluid
Do not add washer fluid when the hybrid
system is hot or operating as washer fluid
contains alcohol and may catch fire if
spilled on the engine, etc.
NOTICE
■ Do not use any fluid other than
washer fluid
Do not use soapy water or engine anti-
freeze instead of washer fluid.
Doing so may cause streaking on the
vehicle’s painted surfaces, as well as
damaging the pump leading to problems
of the washer fluid not spraying.
■ Diluting washer fluid
Dilute washer fluid with water as neces-
sary.
Refer to the freezing temperatures listed
on the label of the washer fluid bottle.
12-volt battery
Location
454
6-3. Do-it-yourself maintenance
not start with the power switch turned off.
However, the hybrid system will operate
normally from the second attempt.
● The power switch mode is recorded by
the vehicle. If the 12-volt battery is recon-
nected, the vehicle will return the power
switch mode to the status it was in before
the 12-volt battery was disconnected.
Make sure to turn off the power switch
before disconnecting the 12-volt battery.
Take extra care when connecting the 12-
volt battery if the power switch mode
prior to the 12-volt battery being discon-
nected is unknown.
If the system will not start even after multiple
attempts at all the methods above, contact
any authorized Lexus retailer or Lexus
authorized repairer, or any reliable
repairer.
*
: ACC mode can be enabled/disabled on
the customize menu. (P.556)
WARNING
■ Chemicals in the 12-volt battery
The 12-volt battery contains poisonous
and corrosive sulfuric acid and may pro-
duce hydrogen gas which is flammable
and explosive. To reduce the risk of
death or serious injury, take the following
precautions while working on or near the
12-volt battery:
● Do not cause sparks by touching the
12-volt battery terminals with tools.
● Do not smoke or light a match near the
12-volt battery.
● Avoid contact with eyes, skin and
clothes.
● Never inhale or swallow electrolyte.
● Wear protective safety glasses when
working near the 12-volt battery.
● Keep children away from the 12-volt
battery.
■ Where to safely charge the 12-volt
battery
Always charge the 12-volt battery in an
open area. Do not charge the 12-volt
battery in a garage or closed room
where there is insufficient ventilation.
■ Emergency measures regarding
electrolyte
● If electrolyte gets in your eyes
Flush your eyes with clean water for at
least 15 minutes and get immediate
medical attention. If possible, continue
to apply water with a sponge or cloth
while traveling to the nearest medical
facility.
● If electrolyte gets on your skin
Wash the affected area thoroughly. If
you feel pain or burning, get medical
attention immediately.
● If electrolyte gets on your clothes
It can soak through clothing on to your
skin. Immediately take off the clothing
and follow the procedure above if nec-
essary.
● If you accidentally swallow electrolyte
Drink a large quantity of water or milk.
Get emergency medical attention
immediately.
■ When handling the 12-volt battery
P.538
NOTICE
■ When recharging the 12-volt battery
Never recharge the 12-volt battery while
the hybrid system is operating. Also, be
sure all accessories are turned off.
455
6
6-3. Do-it-yourself maintenance
Maintenance and care
1 Remove the 2 clips
1 Push in the center part of the clips
2 Remove the clips
2 Remove the 12-volt battery cover.
1 Pull the cover as shown in the illus-
tration to disengage the 3 claws.
2 Pull the cover toward the front of
the vehicle to remove it.
Make sure that the 12-volt battery ter-
minals are not corroded and that there
are no loose connections, cracks, or
loose clamps.
Terminals
Hold-down clamp
1 Install the 12-volt battery cover.
1 Insert the cover as shown in the
illustration to engage the 3 claws.
2 Push the cover.
2 Install the 2 clips.
1 Push out the center part of the clips
Removing the 12-volt battery
cover
Exterior
Installing the 12-volt battery
cover
A
B
456
6-3. Do-it-yourself maintenance
2 Insert the clips
3 Push in the center part of the clips
Check if the treadwear indicators are
showing on the tires. Also check the
tires for uneven wear, such as exces-
sive wear on one side of the tread.
Vehicles with spare tire: Check the
spare tire condition and pressure if not
rotated.
New tread
Worn tread
Treadwear indicator
The location of treadwear indicators is
shown by a “TWI” or “ ” mark, etc.,
Tires
Replace or rotate tires in accor-
dance with maintenance schedules
and treadwear.
Checking tires
A
B
C
457
6
6-3. Do-it-yourself maintenance
Maintenance and care
molded into the sidewall of each tire.
Replace the tires if the treadwear indica-
tors are showing on a tire.
■ When to replace your vehicle’s tires
Tires should be replaced if:
● The treadwear indicators are showing on
a tire.
● You have tire damage such as cuts, splits,
cracks deep enough to expose the fabric,
and bulges indicating internal damage
● A tire goes flat repeatedly or cannot be
properly repaired due to the size or loca-
tion of a cut or other damage
If you are not sure, consult any authorized
Lexus retailer or Lexus authorized repairer,
or any reliable repairer.
■ Tire life
Any tire over 6 years old must be checked
by a qualified technician even if it has sel-
dom or never been used or damage is not
obvious.
■ If the tread on snow tires wears down
below 4 mm (0.16 in.)
The effectiveness of the tires as snow tires is
lost.
Rotate the tires in the order shown.
WARNING
■ When inspecting or replacing tires
Observe the following precautions to
prevent accidents.
Failure to do so may cause damage to
parts of the drivetrain as well as danger-
ous handling characteristics, which may
lead to an accident resulting in death or
serious injury.
● Do not mix tires of different makes,
models or tread patterns.
Also, do not mix tires of remarkably
different treadwear.
● Do not use tire sizes other than those
recommended by Lexus.
● Do not mix differently constructed
tires (radial, bias-belted or bias-ply
tires).
● Do not mix summer, all season and
snow tires.
● Do not use tires that have been used
on another vehicle.
Do not use tires if you do not know
how they were used previously.
● Vehicles with compact spare tire: Do
not tow if your vehicle has a compact
spare tire installed.
● Vehicles with emergency tire punc-
ture repair kit: Do not tow anything if a
tire that has been repaired using the
emergency tire puncture repair kit is
installed. The load on the tire may
cause unexpected damage to the tire.
NOTICE
■ Driving on rough roads
Take particular care when driving on
roads with loose surfaces or potholes.
These conditions may cause losses in tire
inflation pressure, reducing the cushion-
ing ability of the tires. In addition, driving
on rough roads may cause damage to
the tires themselves, as well as the vehi-
cle’s wheels and body.
■ If tire inflation pressure of each tire
becomes low while driving
Do not continue driving, or your tires
and/or wheels may be ruined.
Tire rotation
458
6-3. Do-it-yourself maintenance
To equalize tire wear and help extend tire
life, Lexus recommends that tire rotation is
carried out approximately at the following
intervals:
2WD models: Every 10000 km (6000
miles)
AWD models: Every 5000 km (3000
miles)
Make sure to perform wheel position reg-
istration procedure after rotating the tires.
(P.460)
Your vehicle is equipped with a tire
pressure warning system that uses tire
pressure warning valves and transmit-
ters to detect low tire inflation pressure
before serious problems arise.
The tire pressure warning system of
this vehicle adopts a 2-type warning
system. (P.494)
Multi-information display (vehicles
with 7-inch multi-information dis-
play)
Multi-information display (vehicles
with 12.3-inch multi-information dis-
play)
Center Display
When “Adjust Pressure” is dis-
played on the multi-information dis-
play (Normal Warning)
A warning with the tire pressure warning
light and warning buzzer when there is an
unknown level of low tire pressure with the
Tire pressure warning system
459
6
6-3. Do-it-yourself maintenance
Maintenance and care
appearance of the tire due to natural air
leakage as well as the pressure lowering
due to changes in the pressure according
to the outside temperature.
When “Immediately Check tyre
when Safe” is displayed on the multi-
information display (Emergency
Warning)
A warning with the tire pressure warning
light and warning buzzer when there is a
known level of low tire pressure with the
appearance of the tire due to pressure
suddenly lowering.
However, the system may not be able to
detect sudden tire ruptures (bursting, etc.).
The tire pressure detected by the
tire pressure warning system can be
displayed on the Center Display.
(P.121)
■ Routine tire inflation pressure checks
The tire pressure warning system does not
replace routine tire inflation pressure
checks. Make sure to check tire inflation
pressure as part of your routine of daily
vehicle checks.
■ Tire inflation pressure
● It may take a few minutes to display the
tire inflation pressure after the power
switch is turned to ON. It may also take a
few minutes to display the tire inflation
pressure after inflation pressure has been
adjusted.
● Tire inflation pressure changes with tem-
perature. The displayed values may also
be different from the values measured
using a tire pressure gauge.
■ Situations in which the tire pressure
warning system may not operate prop-
erly
● In the following cases, the tire pressure
warning system may not operate prop-
erly.
• If non-genuine Lexus wheels are used.
• A tire has been replaced with a tire that is
not an OE (Original Equipment) tire.
• A tire has been replaced with a tire that is
not of the specified size.
• Tire chains, etc. are equipped.
• If a window tint that affects the radio wave
signals is installed.
• If there is a lot of snow or ice on the vehi-
cle, particularly around the wheels or
wheel housings.
• If the tire inflation pressure is extremely
higher than the specified level.
• If tires not equipped with tire pressure
warning valves and transmitters are used.
• If the ID code on the tire pressure warn-
ing valves and transmitters is not regis-
tered in the tire pressure warning
computer.
● Performance may be affected in the fol-
lowing situations.
• Near a TV tower, electric power plant,
gas station, radio station, large display,
airport or other facility that generates
strong radio waves or electrical noise
• When carrying a portable radio, cellular
phone, cordless phone or other wireless
communication device
● If tire position information is not correctly
displayed due to the radio wave condi-
tions, the display may be corrected by
changing the location of the vehicle as
the radio wave conditions may change.
● When the vehicle is parked, the time
taken for the warning to start or go off
could be extended.
● When tire inflation pressure declines rap-
idly for example when a tire has burst, the
warning may not operate.
When replacing tires or wheels, tire
pressure warning valves and transmit-
ters must also be installed.
When new tire pressure warning
valves and transmitters are installed,
Installing tire pressure warning
valves and transmitters
460
6-3. Do-it-yourself maintenance
new ID codes must be registered in the
tire pressure warning computer.
(P.463)
■ Replacing tires and wheels
If the ID code of the tire pressure warning
valve and transmitter is not registered, the
tire pressure warning system will not work
properly. In this case, after driving for about
10 minutes, the tire pressure warning light
blinks for 1 minute and stays on to indicate a
system malfunction.
■ When to register the position of
each wheel
It is necessary to register the position
of each wheel after performing a tire
rotation.
Wheel position registration can be
performed by oneself. Wheel position
registration is performed by driving
forward with moderate left and right
turns. However, depending on the
driving conditions and driving environ-
ment, registration may take some time
to complete.
■ Registering the position of each
wheel
1 Park the vehicle in a safe place, turn
the power switch off and wait 15
minutes or more.
2 Start the hybrid system.
The wheel position registration procedure
cannot be performed while the vehicle is
moving.
NOTICE
■ Repairing or replacing tires, wheels,
tire pressure warning valves, trans-
mitters and tire valve caps
● When removing or fitting the wheels,
tires or the tire pressure warning
valves and transmitters, contact any
authorized Lexus retailer or Lexus
authorized repairer, or any reliable
repairer as the tire pressure warning
valves and transmitters may be dam-
aged if not handled correctly.
● Make sure to install the tire valve caps.
If the tire valve caps are not installed,
water could enter the tire pressure
warning valves, corrode the valve, and
cause sticking and air leaks.
● When replacing tire valve caps, do not
use tire valve caps other than those
specified. The cap may become stuck.
■ To avoid damage to the tire pressure
warning valves and transmitters
(vehicles with an emergency tire
puncture repair kit)
When a tire is repaired with liquid seal-
ants, the tire pressure warning valve and
transmitter may not operate properly. If a
liquid sealant is used, contact any autho-
rized Lexus retailer or Lexus authorized
repairer, or any reliable repairer or other
qualified service shop as soon as possi-
ble. Make sure to replace the tire pres-
sure warning valve and transmitter when
replacing the tire. (P.459)
Registering the position of each
wheel
461
6
6-3. Do-it-yourself maintenance
Maintenance and care
3 Select on the Center Display.
4 Select “Vehicle customise”.
5 Select “Tyre pressure”.
6 Select “Tyre rotation”.
7 Select “Continue”.
A message indicating that wheel position
registration is being performed will be dis-
played on the multi-information display. “--
-” will be displayed for the tire inflation
pressure of each tire and wheel position
registration will begin.
8 Drive straight (with occasional left
and right turns) at approximately
40 km/h (25 mph) or more for
approximately 10 to 30 minutes.
When wheel position registration is com-
plete, a message indicating that registra-
tion has been completed and the inflation
pressure of each tire will be displayed on
the multi-information display.
Even if it is not possible to drive continu-
ously at approximately 40 km/h (25 mph)
or more, registration can be completed by
driving for a long time. However, if regis-
tration does not complete after driving for 1
hour or more, park the vehicle in a safe
place and leave it with the power switch in
ON for approximately 15 minutes or more,
and then perform the driving procedure
again.
■ When performing wheel position regis-
tration
● Normally, wheel position registration can
be completed within approximately 30
minutes.
● Wheel position registration is performed
while driving at a vehicle speed of
approximately 40 km/h (25 mph) or
more.
■ Wheel position registration procedure
● If the power switch is turned off while reg-
istering the wheel position, the next time
the power switch is turned to ON, the
wheel position registration will resume
and it will not be necessary to restart the
procedure.
● While the position of each wheel is being
determined and the inflation pressures
are not being displayed, if the inflation
pressure of a tire drops, the tire pressure
warning light will come on.
■ If the wheel position cannot be regis-
tered easily
● In the following situations, wheel position
registration may take longer than usual to
be completed or may not be possible.
• Vehicle is not driven at approximately 40
km/h (25 mph) or more
• Vehicle is driven on unpaved roads
● If wheel position registration does not
complete after driving for 1 hour or more,
park the vehicle in a safe place for
approximately 15 minutes and then drive
the vehicle again.
● If the vehicle is reversed during wheel
position registration, all data collected
until then will be cleared. Perform driving
again.
■ When you need to setting the tire
pressure
In the following situations, it will be nec-
essary to perform the tire inflation
pressure setting procedure of the tire
pressure warning system.
When the specified tire inflation
pressure has changed, such as due
to carried load, etc.
When the tire inflation pressure is
changed such as when the tire size
is changed.
If the tire inflation pressure has been
adjusted to the specified level, perform
the tire inflation setting procedure by
Setting the tire pressure
462
6-3. Do-it-yourself maintenance
selecting specified inflation pressure
on the Center Display. (P.462)
When the tire inflation pressure is to be
other than specified, such as when tires
other than the specified size are used,
etc., set the tire inflation pressure using
the current pressure. Make sure to
adjust the tire inflation pressure of each
tire to the appropriate level before
performing tire pressure setting. The
tire pressure warning system operates
based on this tire inflation pressure.
(P.462)
■ Setting by selecting a specified tire
inflation pressure
1 Start the hybrid system.
The tire inflation pressure cannot be set
while the vehicle is moving.
2 Select on the Center Display.
3 Select “Vehicle customise”.
4 Select “Tyre pressure”.
5 Select “Set indicated air pressure”
and then select the desired front
and rear tire pressures.
6 Select “OK”.
The tire pressure warning light will slowly
blink 3 times.
After setting the tire inflation pressure, a
message indicating that setting has been
completed will be displayed on the multi-
information display.
■ Setting using the current tire infla-
tion pressure
1 Adjust the tire inflation pressure of
each tire to the appropriate level.
Make sure to adjust the tire inflation pres-
sure with the tires cold.
2 Start the hybrid system.
The tire inflation pressure cannot be set
while the vehicle is moving.
3 Select on the Center Display.
4 Select “Vehicle customise”.
5 Select “Tyre pressure”.
6 Select “Set current air pressure”.
7 Select “Continue”.
The tire pressure warning light will slowly
blink 3 times and a message indicating that
tire inflation pressure is being set will be
displayed on the multi-information display.
After setting the tire inflation pressure, a
message indicating that setting has been
completed will be displayed on the multi-
463
6
6-3. Do-it-yourself maintenance
Maintenance and care
information display.
■ Warning performance of the tire pres-
sure warning system (Setting using the
current tire inflation pressure)
● When performing the tire pressure set-
ting using the current tire inflation pres-
sure, the warning timing of the tire
pressure warning system will vary
according to the conditions under which
tire pressure setting was performed.
Therefore, a warning may be output even
if the tire inflation pressure drops slightly
or if the tire inflation pressure increases
above that when the tire inflation pres-
sure was set.
● Make sure to perform the tire pressure
setting procedure after adjusting the tire
inflation pressure. Also, make sure the
tires are cold before performing the tire
pressure setting procedure or adjusting
the tire inflation pressure.
■ Tire inflation pressure setting proce-
dure (Setting using the current tire infla-
tion pressure)
● If the power switch is turned off while set-
ting the tire inflation pressure, the next
time the power switch is turned to ON,
the setting procedure will resume and it
will not be necessary to restart the proce-
dure.
● If the tire inflation pressure setting proce-
dure is started unnecessarily, adjust the
tire inflation pressure to the specified
level with the tires cold and then perform
setting by selecting a specified tire infla-
tion pressure, or perform the tire inflation
pressure setting procedure with the cur-
rent tire inflation pressure.
■ If the tire inflation pressure cannot be
set easily
● Normally, it takes approximately 3 min-
utes to complete the setting procedure to
the current tire inflation pressure.
● If the tire pressure warning light does not
blink 3 times when starting the tire infla-
tion pressure setting procedure, the pro-
cedure may not have started. Perform
the procedure again from the beginning.
● If tire inflation pressure setting procedure
cannot be completed after performing
the above procedure, contact any autho-
rized Lexus retailer or Lexus authorized
repairer, or any reliable repairer.
■ When to register ID codes
The tire pressure warning valve and
transmitter is equipped with a unique
ID code. When new tire pressure
warning valves and transmitters are
installed, new ID codes must be regis-
tered in the tire pressure warning com-
puter.
■ How to registration ID code
Before performing ID code registra-
tion, make sure that no wheels with tire
pressure warning valve and transmit-
ters installed are near the vehicle.
WARNING
■ When setting using the current tire
inflation pressure
Make sure to adjust the tire inflation
pressure of each tire to the appropriate
level before performing tire pressure
setting. Otherwise, the tire pressure
warning light may not illuminate even if
the tire inflation pressure drops or may
illuminate even though the tire inflation
pressure is normal.
Registering ID codes
464
6-3. Do-it-yourself maintenance
1 Park the vehicle in a safe place, turn
the power switch off and wait 15
minutes or more.
2 Start the hybrid system.
The ID code registration procedure can-
not be performed while the vehicle is mov-
ing.
3 Select on the Center Display.
4 Select “Vehicle customise”.
5 Select “Tyre pressure”.
6 Check if the desired wheel set (“Set
1” or “Set 2”) is displayed.
ID codes will be registered to the displayed
wheel set.
To change the wheel set to be registered,
select the displayed set, and then select the
wheel set you wish to register.
If ID codes have already been registered
for that wheel set, the tire pressure warning
light will slowly blink 3 times, and a mes-
sage indicating that change is occurring
will be displayed on the multi-information
display.
7 Select “New tyre registration”.
8 Select “Continue”.
The tire pressure warning light will slowly
blink 3 times and a message indicating that
ID code registration is being performed
will be displayed on the multi-information
display. Wheel set changing will be can-
celed and registration will begin.
When registration is being performed, the
tire pressure warning light will blink for
approximately 1 minute then illuminate and
“---” will be displayed for the inflation pres-
sure of each tire on the multi-information
display.
9 Drive straight (with occasional left
and right turns) at approximately
40 km/h (25 mph) or more for
approximately 10 to 30 minutes.
When registration is complete, the tire
pressure warning light will turn off and a
message indicating that registration has
been completed will be displayed on the
multi-information display.
Registration may take longer than normal
to complete if the vehicle speed cannot be
maintained at approximately 40 km/h (25
mph) or more. If registration cannot be
completed after driving for 1 hour or more,
perform the registration procedure again
from the beginning.
10 If the tire inflation pressure of the
wheel set installed differs from that
of the previous set, it will be neces-
sary to perform the tire inflation
pressure setting procedure of the
tire pressure warning system.
(P.461)
If the specified tire inflation pressure is the
same, it will not be necessary to perform
the tire inflation pressure setting proce-
dure.
465
6
6-3. Do-it-yourself maintenance
Maintenance and care
■ When registering ID codes
● Normally, wheel position registration can
be completed within approximately 30
minutes.
● ID code registration is performed while
driving at a vehicle speed of approxi-
mately 40 km/h (25 mph) or more.
● ID codes can be registered by yourself,
but depending on the driving conditions
and driving environment, registration
may take some time to complete.
● When using a wheel set which all of the
ID codes have already been registered,
the wheel set can be changed in a short
amount of time. (P.465)
■ If ID codes are not registered easily
● In the following situations, ID code regis-
tration may take longer than usual to be
completed or may not be possible.
• When the vehicle has not been parked
for approximately 15 minutes or more
before being driven
• Vehicle is not driven at approximately 40
km/h (25 mph) or more
• Vehicle is driven on unpaved roads
• Vehicle is driven near other vehicles and
system cannot recognize tire pressure
warning valve and transmitters of your
vehicle over those of other vehicles
• Wheel with tire pressure warning valve
and transmitter installed is inside or near
the vehicle
● If the vehicle is reversed during registra-
tion, all data collected until then will be
cleared. Perform driving again.
● If registration does not complete after
driving for 1 hour or more, perform the ID
code registration procedure again from
the beginning.
● If the tire pressure warning light does not
blink 3 times when starting ID code reg-
istration procedure, the procedure may
not have started. Perform the procedure
again from the beginning.
● If the ID codes cannot be registered even
when performing the above procedure,
contact any authorized Lexus retailer or
Lexus authorized repairer, or any reliable
repairer.
To cancel ID code registration after it
has been started, select “New tyre reg-
istration” again on the Center Display.
If ID code registration has been canceled,
the tire pressure warning light will turn off.
If the warning light does not turn off, ID
code registration may not have been
cancelled correctly. To cancel registration,
select “New tyre registration” again on the
Center Display.
Your vehicle is equipped with a tire
pressure warning system with a func-
tion to register two sets of ID codes.
This allows for registration of a second
wheel set, for example a winter set.
The wheel set can be changed only
if a second wheel set has been reg-
istered to the system. If a second
wheel set has not been registered,
“Set 2 (Unregistered)” will be dis-
played and it will not be possible to
change to the selected wheel set.
ID codes can be registered by yourself.
(P.463)
Only a change between both regis-
tered wheel set is possible, mixing
between these wheel sets is not sup-
ported.
While registering ID codes, it may
not be possible to change between
wheel sets normally. Cancel regis-
tration before changing between
Canceling ID code registration
Selecting wheel set
466
6-3. Do-it-yourself maintenance
wheel sets.
■ Changing ID codes between dif-
ferent wheel sets
1 Install the desired wheel set.
2 Select on the Center Display.
3 Select “Vehicle customise”.
4 Select “Tyre pressure”.
5 Select the wheel set (“Set 1” or “Set
2”) displayed for the set selection
setting.
6 Select the wheel set you wish to
register, and then select “OK”.
The tire pressure warning light will slowly
blink 3 times, a message indicating that
change is occurring will be displayed, and
the wheel set change will begin.
Wheel set change will begin and the tire
pressure warning light will blink for 1 min-
ute and then illuminate. Also, while the
change is being performed, “---” will be
displayed for the tire inflation pressure of
each tire on the multi-information display.
After approximately 2 minutes, the wheel
set change will complete, the tire pressure
warning light will turn off, and a completion
message will be displayed on the multi-
information display.
If changing does not complete after
approximately 4 minutes, a message indi-
cating that the change could not be com-
pleted will be displayed.
Check which wheel set is installed and per-
form the change procedure again from the
beginning.
7 If the specified tire inflation pres-
sure of the wheel set installed dif-
fers from that of the previous set, it
will be necessary to perform the
tire inflation pressure setting pro-
cedure of the tire pressure warning
system. (P.461)
If the specified tire inflation pressure is the
same, it will not be necessary to perform
the tire inflation pressure setting proce-
dure.
8 Register the position of each wheel.
(P.460)
467
6
6-3. Do-it-yourself maintenance
Maintenance and care
■ Effects of incorrect tire inflation pres-
sure
Driving with incorrect tire inflation pressure
may result in the following:
● Reduced fuel economy
● Reduced driving comfort and poor han-
dling
● Reduced tire life due to wear
● Reduced safety
● Damage to the drive train
If a tire needs frequent inflating, have it
checked by any authorized Lexus retailer
or Lexus authorized repairer, or any reli-
able repairer.
■ Instructions for checking tire inflation
pressure
When checking tire inflation pressure,
observe the following:
● Check only when the tires are cold.
If your vehicle has been parked for at
least 3 hours or has not been driven for
more than 1.5 km or 1 mile, you will get an
accurate cold tire inflation pressure read-
ing.
● Always use a tire pressure gauge.
It is difficult to judge if a tire is properly
inflated based only on its appearance.
● It is normal for the tire inflation pressure
to be higher after driving as heat is gener-
ated in the tire. Do not reduce tire infla-
tion pressure after driving.
● Passengers and luggage weight should
be placed so that the vehicle is balanced.
Tire inflation pressure
Make sure to maintain proper tire
inflation pressure. Tire inflation
pressure should be checked at
least once per month. However,
Lexus recommends that tire infla-
tion pressure be checked once
every two weeks.
WARNING
■ Proper inflation is critical to save tire
performance
Keep your tires properly inflated.
If the tires are not properly inflated, the
following conditions may occur which
could lead to an accident resulting in
death or serious injury:
● Excessive wear
● Uneven wear
● Poor handling
● Possibility of blowouts resulting from
overheated tires
● Air leaking from between tire and
wheel
● Wheel deformation and/or tire dam-
age
● Greater possibility of tire damage
while driving (due to road hazards,
expansion joints, sharp edges in the
road, etc.)
NOTICE
■ When inspecting and adjusting tire
inflation pressure
Be sure to put the tire valve caps back
on.
If a valve cap is not installed, dirt or mois-
ture may get into the valve and cause an
air leak, resulting in decreased tire infla-
tion pressure.
468
6-3. Do-it-yourself maintenance
When replacing wheels, care should
be taken to ensure that they are equiv-
alent to those removed in load capac-
ity, diameter, rim width and inset
*
.
Replacement wheels are available at
any authorized Lexus retailer or Lexus
authorized repairer, or any reliable
repairer.
*
: Conventionally referred to as offset.
Lexus does not recommend using the
following:
Wheels of different sizes or types
Used wheels
Bent wheels that have been
straightened
■ When replacing wheels
The wheels of your vehicle are equipped
with tire pressure warning valves and trans-
mitters that allow the tire pressure warning
system to provide advance warning in the
event of a loss in tire inflation pressure.
Whenever wheels are replaced, tire pres-
sure warning valves and transmitters must
be installed. (P.458, 468)
Use only Lexus wheel bolts and
wrenches designed for use with
your aluminum wheels.
When rotating, repairing or chang-
Wheels
If a wheel is bent, cracked or heav-
ily corroded, it should be replaced.
Otherwise, the tire may separate
from the wheel or cause a loss of
handling control.
Wheel selection
WARNING
■ When replacing wheels
● Do not use wheels that are a different
size from those recommended in the
Owner’s Manual, as this may result in a
loss of handling control.
● Never use an inner tube in a leaking
wheel which is designed for a tubeless
tire. Doing so may result in an acci-
dent, causing death or serious injury.
■ Use of defective wheels prohibited
Do not use cracked or deformed wheels.
Doing so could cause the tire to leak air
during driving, possibly causing an acci-
dent.
NOTICE
■ Replacing tire pressure warning
valves and transmitters
● Because tire repair or replacement
may affect the tire pressure warning
valves and transmitters, make sure to
have tires serviced by any authorized
Lexus retailer or Lexus authorized
repairer, or any reliable repairer or
other qualified service shop. In addi-
tion, make sure to purchase your tire
pressure warning valves and transmit-
ters at any authorized Lexus retailer or
Lexus authorized repairer, or any reli-
able repairer.
● Ensure that only genuine Lexus wheels
are used on your vehicle.
Tire pressure warning valves and
transmitters may not work properly
with non-genuine wheels.
Aluminum wheel precautions
469
6
6-3. Do-it-yourself maintenance
Maintenance and care
ing your tires, check that the wheel
bolts are still tight after driving 1600
km (1000 miles).
Be careful not to damage the alumi-
num wheels when using tire chains.
Use only Lexus genuine balance
weights or equivalent and a plastic
or rubber hammer when balancing
your wheels.
1 Turn the power switch off.
2 Open the glove box and slide off
the damper.
3 Push in each side of the glove box
to disconnect the claws, and then
slowly and fully open the glove box
while supporting it.
Air conditioning filter
The air conditioning filter must be
changed regularly to maintain air
conditioning efficiency.
Removing the air conditioning
filter
470
6-3. Do-it-yourself maintenance
4 With the glove box fully open,
slightly lift up the glove box and pull
toward the seat to detach the bot-
tom of the glove box.
Do not use excessive force if the glove box
does not detach when lightly pulled.
Instead, pull toward the seat while slightly
adjusting the height of the glove box.
5 Unlock the filter cover ( ), pull
the filter cover out of the claws
( ), and remove the filter cover.
6 For cold region specification vehi-
cles: Remove the filter case.
Except for cold region specification vehi-
cles: Remove the filter.
7 For cold region specification vehi-
cles: Remove the air conditioning
filter from the filter case and
replace it with a new one.
The “ UP” marks shown on the filter and
the filter case should be pointing up.
Except for cold region specification vehi-
cles: Replace the air conditioning filter with
a new one.
The “ UP” marks shown on the filter and
the filter case should be pointing up.
A
B
471
6
6-3. Do-it-yourself maintenance
Maintenance and care
■ Checking interval
Inspect and replace the air conditioning fil-
ter according to the maintenance schedule.
In dusty areas or areas with heavy traffic
flow, early replacement may be required.
(For scheduled maintenance information,
please refer to the “Lexus Service Booklet”
or “Lexus Warranty Booklet”.)
■ If air flow from the vents decreases dra-
matically
The filter may be clogged. Check the filter
and replace if necessary.
■ Air conditioning filter with deodorizing
function
When fragrances are placed in your vehi-
cle, the deodorizing effect may become sig-
nificantly weakened in a short period.
When an air conditioning odor comes out
continuously, replace the air conditioning
filter.
■ Scheduled maintenance of the air
intake vent is necessary when
In some situations such as when the vehicle
is used frequently or in heavy traffic or dusty
areas, the air intake vent may need to be
cleaned more regularly. For details, refer to
the “Lexus Service Booklet” or “Lexus War-
ranty Booklet”.
■ Cleaning the air intake vent
Improper handling of the air intake vent
cover and filter may result in damage to
them. If you have any concerns about clean-
ing the filter, contact any authorized Lexus
retailer or Lexus authorized repairer, or any
reliable repairer.
NOTICE
■ When using the air conditioning sys-
tem
Make sure that a filter is always installed.
Using the air conditioning system with-
out a filter may cause damage to the sys-
tem.
■ To prevent damage to the filter cover
When moving the filter cover in the
direction of arrow to release the fitting,
pay attention not to apply excessive
force to the claws. Otherwise, the claws
may be damaged.
Cleaning the hybrid battery
(traction battery) air intake
vent
To prevent the fuel economy from
being affected, visually inspect the
hybrid battery (traction battery) air
intake vent periodically for clogs.
If it is dusty or clogged or if “Main-
tenance Required for Traction Bat-
tery Cooling Parts See Owner’s
Manual” is displayed on the multi-
information display, clean the air
intake vent using the following pro-
cedures:
WARNING
■ If “Maintenance Required for Trac-
tion Battery Cooling Parts See
Owner’s Manual” is displayed on the
multi-information display
Clean the air intake vent immediately.
If the vehicle is continuously driven with
the warning message displayed, it may
cause a malfunction or output restriction
of the hybrid battery (traction battery).
472
6-3. Do-it-yourself maintenance
1 Turn the power switch off.
2 Using a flathead screwdriver,
remove the air intake vent cover.
1 Pull the cover as shown in the illus-
tration to disengage the 4 claws,
starting from the claw in the upper
right corner.
2 Pull the cover toward the front of
the vehicle to remove it.
3 Remove the filter from the air
intake vent cover.
If dust has accumulated on the air intake
vent cover, remove the dust with a vacuum
cleaner, etc.
1 Disengage the 2 claws as shown in
the illustration.
2 Disengage the 2 claws and remove
the filter from the cover.
4 Remove the dust and sand from the
filter.
Using a vacuum cleaner, etc., absorb dust
and sand from the filter by profiling the
nozzle lightly along the fold.
5 Hold the filter to the light and check
if it is not clogged.
If the dust or sand cannot be removed
completely, contact any authorized Lexus
retailer or Lexus authorized repairer, or
any reliable repairer.
6 Reinstall the filter to the cover.
1 Engage the filter to the 2 claws as
shown in the illustration.
Cleaning procedure
473
6
6-3. Do-it-yourself maintenance
Maintenance and care
2 Engage the filter to the 2 claws to
reinstall the filter.
Make sure that the filter is not crooked or
deformed when installing it.
7 Install the air intake vent cover.
1 Insert the tab of the cover as shown
in the illustration.
2 Push the cover to engage the 4
claws.
If “Maintenance Required for Trac-
tion Battery Cooling Parts See
Owner’s Manual” is displayed on
the multi-information display
8 Start the hybrid system and check
that the warning message is no lon-
ger displayed.
It may be necessary to drive the vehicle for
approximately 20 minutes before the
warning message is displayed again then
disappears.
If the warning message does not disappear
after some time, have the vehicle inspected
by any authorized Lexus retailer or Lexus
authorized repairer, or any reliable
repairer.
■ If the dust or sand on the filter cannot be
removed
It is recommended to use a vacuum cleaner
with plastic brushes.
WARNING
■ When cleaning the air intake vent
● Do not use water or other liquids to
clean the air intake vent. If water is
applied to the hybrid battery (traction
battery) or other components, a mal-
function or fire may occur.
● Do not touch the service plug located
near the air intake vent. (P.80)
● Before cleaning the air intake vent,
make sure to turn the power switch off
to stop the hybrid system.
● Do not put a hand or leg in the air
intake vent. If it is caught in a cooling
fan, or if it touches a high voltage part
that results in an electric shock, death
or serious injuries may result.
NOTICE
■ When cleaning the air intake vent
Do not use an air blow gun, etc.
Dust may be blown out, possibly causing
a malfunction or output restriction of the
hybrid battery (traction battery).
■ To prevent damage to the vehicle
Observe the following precautions:
● Do not allow water or foreign matter
to enter the air intake vent.
● Make sure to reinstall the filter and
cover to their original positions after
cleaning.
474
6-3. Do-it-yourself maintenance
■ If the electronic key battery is depleted
The following symptoms may occur:
● The smart entry & start system and wire-
less remote control will not function
properly.
● The operational range will be reduced.
Prepare the following before replacing
the battery:
Flathead screwdriver
Small flathead screwdriver
Lithium battery CR2032
■ Use a CR2032 lithium battery
● Batteries can be purchased at any autho-
rized Lexus retailer or Lexus authorized
repairer, or any reliable repairer, local
electrical appliance shops or camera
stores.
● Replace only with the same or equivalent
type recommended by the manufacturer.
● Dispose of used batteries according to
the local laws.
NOTICE
● Do not install anything to the air intake
vent other than the exclusive filter for
this vehicle or use the vehicle without
the filter installed.
■ To prevent damage to the filter
Observe the following precautions.
If the filter is damaged, have it replaced
with a new filter by any authorized Lexus
retailer or Lexus authorized repairer, or
any reliable repairer.
● Do not use an air blow gun, etc.
● Do not press hard a vacuum cleaner,
etc. against the filter.
● Do not use a hard brush, such as a
metal brush.
● Do not break the fold of the filter.
Electronic key battery
Replace the battery with a new one
if it is depleted.
As the key may be damaged if the
following procedure is not per-
formed properly, it is recom-
mended that key battery
replacement be performed by any
authorized Lexus retailer or Lexus
authorized repairer, or any reliable
repairer.
Items to prepare
475
6
6-3. Do-it-yourself maintenance
Maintenance and care
1 Take out the mechanical key.
2 Remove the cover.
3 Remove the battery cover.
4 Remove the depleted battery.
Insert a new battery with the “+” terminal
facing up.
Replacing the battery
WARNING
■ Battery precautions
Observe the following precautions. Fail-
ure to do so may result in death or seri-
ous injury.
● Do not swallow the battery. Doing so
may cause chemical burns.
● A coin battery or button battery is
used in the electronic key. If a battery
is swallowed, it may cause severe
chemical burns in as little as 2 hours
and may result in death or serious
injury.
● Keep away new and removed batter-
ies from children.
● If the cover cannot be firmly closed,
stop using the electronic key and stow
the key in the place where children
cannot reach, and then contact any
authorized Lexus retailer or Lexus
authorized repairer, or any reliable
repairer.
● If you accidentally swallow a battery or
put a battery into a part of your body,
get emergency medical attention
immediately.
■ To prevent battery explosion or leak-
age of flammable liquid or gas
● Replace the battery with a new battery
of the same type. If a wrong type of
battery is used, it may explode.
476
6-3. Do-it-yourself maintenance
1 Turn the power switch off.
2 Open the fuse box cover.
Engine compartment: type A fuse
box
Push the tab in and lift the lid off.
Engine compartment: type B fuse
box
Push the tab in and lift the lid off.
WARNING
● Do not expose batteries to extremely
low pressure due to high altitude or
extremely high temperatures.
● Do not burn, break or cut a battery.
NOTICE
■ When replacing the battery
Use a flathead screwdriver of appropri-
ate size. Applying excessive force may
deform or damage the cover.
■ For normal operation after replacing
the battery
Observe the following precautions to
prevent accidents:
● Always work with dry hands.
Moisture may cause the battery to
rust.
● Do not touch or move any other com-
ponent inside the remote control.
● Do not bend either of the battery ter-
minals.
Checking and replacing
fuses
If any of the electrical components
do not operate, a fuse may have
blown. If this happens, check and
replace the fuses as necessary.
Checking and replacing fuses
477
6
6-3. Do-it-yourself maintenance
Maintenance and care
Left side instrument panel (left-hand
drive vehicles)
Remove the lid.
Left side instrument panel (right-
hand drive vehicles)
Remove the cover.
1 Push the tab in and remove the
cover.
2 Unplug the connector and fix-
ing part while pressing the lock
release.
3 Remove the lid.
Right side rear seat
Remove the 12-volt battery cover
(P.455).
You can inspect or replace fuse by
yourself.
It is necessary to remove the 12-volt bat-
tery when inspecting or replacing fuse .
As there is a danger that components may
be damaged, we recommend that inspec-
tion and replacement be carried by any
authorized Lexus retailer or Lexus autho-
rized repairer, or any reliable repairer.
3 Remove the fuse.
Only type A fuse can be removed using
the pullout tool.
4 Check if the fuse is blown.
Replace the blown fuse with a new fuse of
an appropriate amperage rating. The
amperage rating can be found on the fuse
box lid.
A
B
A
B
478
6-3. Do-it-yourself maintenance
Type A
Normal fuse
Blown fuse
Type B
Normal fuse
Blown fuse
Type C
Normal fuse
Blown fuse
Type D
Normal fuse
Blown fuse
■ After a fuse is replaced
● When installing the lid, make sure that the
tab is installed securely.
● If the lights do not turn on even after the
fuse has been replaced, a bulb may need
replacement. (P.479)
● If the replaced fuse blows again, have the
vehicle inspected by any authorized
Lexus retailer or Lexus authorized
repairer, or any reliable repairer.
■ If there is an overload in a circuit
The fuses are designed to blow, protecting
the wiring harness from damage.
■ When replacing light bulbs
Lexus recommends that you use genuine
Lexus products designed for this vehicle.
Because certain bulbs are connected to cir-
cuits designed to prevent overload, non-
genuine parts or parts not designed for this
vehicle may be unusable.
A
B
A
B
A
B
A
B
479
6
6-3. Do-it-yourself maintenance
Maintenance and care
■ LED lights
The lights consist of a number of LEDs. If
any of the LEDs burn out, take your vehicle
to any authorized Lexus retailer or Lexus
authorized repairer, or any reliable repairer
to have the light replaced.
■ Condensation build-up on the inside of
the lens
Temporary condensation build-up on the
inside of the headlight lens does not indi-
cate a malfunction. Contact any authorized
Lexus retailer or Lexus authorized repairer,
or any reliable repairer for more informa-
tion in the following situations:
● Large drops of water have built up on the
inside of the lens.
● Water has built up inside the headlight.
■ When replacing an electric component,
such as a lights, etc.
P.478
WARNING
■ To prevent system breakdowns and
vehicle fire
Observe the following precautions.
Failure to do so may cause damage to
the vehicle, and possibly a fire or injury.
● Never use a fuse of a higher amperage
rating than that indicated, or use any
other object in place of a fuse.
● Always use a genuine Lexus fuse or
equivalent.
Never replace a fuse with a wire, even
as a temporary fix.
● Do not modify the fuses or fuse boxes.
■ Fuse box near the power control unit
Never check or replace the fuses as
there are high voltage parts and wiring
near the fuse box.
Doing so may cause electric shock,
resulting in death or serious injury.
NOTICE
■ Before replacing fuses
Have the cause of electrical overload
determined and repaired by any autho-
rized Lexus retailer or Lexus authorized
repairer, or any reliable repairer as soon
as possible.
Exterior lights
If any exterior light does not turn
on, have it replaced by any autho-
rized Lexus retailer or Lexus autho-
rized repairer, or any reliable
repairer.

Related Topics

Popular Owner Manuals