2024-2026 Lexus LBX SUV Maintenance and care -> Tires User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Maintenance and care -> Tires for Your Lexus LBX SUV First Generation (2024-2026)

456
6-3. Do-it-yourself maintenance
2 Insert the clips
3 Push in the center part of the clips
Check if the treadwear indicators are
showing on the tires. Also check the
tires for uneven wear, such as exces-
sive wear on one side of the tread.
Vehicles with spare tire: Check the
spare tire condition and pressure if not
rotated.
New tread
Worn tread
Treadwear indicator
The location of treadwear indicators is
shown by a “TWI” or “ ” mark, etc.,
Tires
Replace or rotate tires in accor-
dance with maintenance schedules
and treadwear.
Checking tires
A
B
C
457
6
6-3. Do-it-yourself maintenance
Maintenance and care
molded into the sidewall of each tire.
Replace the tires if the treadwear indica-
tors are showing on a tire.
■ When to replace your vehicle’s tires
Tires should be replaced if:
● The treadwear indicators are showing on
a tire.
● You have tire damage such as cuts, splits,
cracks deep enough to expose the fabric,
and bulges indicating internal damage
● A tire goes flat repeatedly or cannot be
properly repaired due to the size or loca-
tion of a cut or other damage
If you are not sure, consult any authorized
Lexus retailer or Lexus authorized repairer,
or any reliable repairer.
■ Tire life
Any tire over 6 years old must be checked
by a qualified technician even if it has sel-
dom or never been used or damage is not
obvious.
■ If the tread on snow tires wears down
below 4 mm (0.16 in.)
The effectiveness of the tires as snow tires is
lost.
Rotate the tires in the order shown.
WARNING
■ When inspecting or replacing tires
Observe the following precautions to
prevent accidents.
Failure to do so may cause damage to
parts of the drivetrain as well as danger-
ous handling characteristics, which may
lead to an accident resulting in death or
serious injury.
● Do not mix tires of different makes,
models or tread patterns.
Also, do not mix tires of remarkably
different treadwear.
● Do not use tire sizes other than those
recommended by Lexus.
● Do not mix differently constructed
tires (radial, bias-belted or bias-ply
tires).
● Do not mix summer, all season and
snow tires.
● Do not use tires that have been used
on another vehicle.
Do not use tires if you do not know
how they were used previously.
● Vehicles with compact spare tire: Do
not tow if your vehicle has a compact
spare tire installed.
● Vehicles with emergency tire punc-
ture repair kit: Do not tow anything if a
tire that has been repaired using the
emergency tire puncture repair kit is
installed. The load on the tire may
cause unexpected damage to the tire.
NOTICE
■ Driving on rough roads
Take particular care when driving on
roads with loose surfaces or potholes.
These conditions may cause losses in tire
inflation pressure, reducing the cushion-
ing ability of the tires. In addition, driving
on rough roads may cause damage to
the tires themselves, as well as the vehi-
cle’s wheels and body.
■ If tire inflation pressure of each tire
becomes low while driving
Do not continue driving, or your tires
and/or wheels may be ruined.
Tire rotation
458
6-3. Do-it-yourself maintenance
To equalize tire wear and help extend tire
life, Lexus recommends that tire rotation is
carried out approximately at the following
intervals:
2WD models: Every 10000 km (6000
miles)
AWD models: Every 5000 km (3000
miles)
Make sure to perform wheel position reg-
istration procedure after rotating the tires.
(P.460)
Your vehicle is equipped with a tire
pressure warning system that uses tire
pressure warning valves and transmit-
ters to detect low tire inflation pressure
before serious problems arise.
The tire pressure warning system of
this vehicle adopts a 2-type warning
system. (P.494)
Multi-information display (vehicles
with 7-inch multi-information dis-
play)
Multi-information display (vehicles
with 12.3-inch multi-information dis-
play)
Center Display
When “Adjust Pressure” is dis-
played on the multi-information dis-
play (Normal Warning)
A warning with the tire pressure warning
light and warning buzzer when there is an
unknown level of low tire pressure with the
Tire pressure warning system
459
6
6-3. Do-it-yourself maintenance
Maintenance and care
appearance of the tire due to natural air
leakage as well as the pressure lowering
due to changes in the pressure according
to the outside temperature.
When “Immediately Check tyre
when Safe” is displayed on the multi-
information display (Emergency
Warning)
A warning with the tire pressure warning
light and warning buzzer when there is a
known level of low tire pressure with the
appearance of the tire due to pressure
suddenly lowering.
However, the system may not be able to
detect sudden tire ruptures (bursting, etc.).
The tire pressure detected by the
tire pressure warning system can be
displayed on the Center Display.
(P.121)
■ Routine tire inflation pressure checks
The tire pressure warning system does not
replace routine tire inflation pressure
checks. Make sure to check tire inflation
pressure as part of your routine of daily
vehicle checks.
■ Tire inflation pressure
● It may take a few minutes to display the
tire inflation pressure after the power
switch is turned to ON. It may also take a
few minutes to display the tire inflation
pressure after inflation pressure has been
adjusted.
● Tire inflation pressure changes with tem-
perature. The displayed values may also
be different from the values measured
using a tire pressure gauge.
■ Situations in which the tire pressure
warning system may not operate prop-
erly
● In the following cases, the tire pressure
warning system may not operate prop-
erly.
• If non-genuine Lexus wheels are used.
• A tire has been replaced with a tire that is
not an OE (Original Equipment) tire.
• A tire has been replaced with a tire that is
not of the specified size.
• Tire chains, etc. are equipped.
• If a window tint that affects the radio wave
signals is installed.
• If there is a lot of snow or ice on the vehi-
cle, particularly around the wheels or
wheel housings.
• If the tire inflation pressure is extremely
higher than the specified level.
• If tires not equipped with tire pressure
warning valves and transmitters are used.
• If the ID code on the tire pressure warn-
ing valves and transmitters is not regis-
tered in the tire pressure warning
computer.
● Performance may be affected in the fol-
lowing situations.
• Near a TV tower, electric power plant,
gas station, radio station, large display,
airport or other facility that generates
strong radio waves or electrical noise
• When carrying a portable radio, cellular
phone, cordless phone or other wireless
communication device
● If tire position information is not correctly
displayed due to the radio wave condi-
tions, the display may be corrected by
changing the location of the vehicle as
the radio wave conditions may change.
● When the vehicle is parked, the time
taken for the warning to start or go off
could be extended.
● When tire inflation pressure declines rap-
idly for example when a tire has burst, the
warning may not operate.
When replacing tires or wheels, tire
pressure warning valves and transmit-
ters must also be installed.
When new tire pressure warning
valves and transmitters are installed,
Installing tire pressure warning
valves and transmitters
460
6-3. Do-it-yourself maintenance
new ID codes must be registered in the
tire pressure warning computer.
(P.463)
■ Replacing tires and wheels
If the ID code of the tire pressure warning
valve and transmitter is not registered, the
tire pressure warning system will not work
properly. In this case, after driving for about
10 minutes, the tire pressure warning light
blinks for 1 minute and stays on to indicate a
system malfunction.
■ When to register the position of
each wheel
It is necessary to register the position
of each wheel after performing a tire
rotation.
Wheel position registration can be
performed by oneself. Wheel position
registration is performed by driving
forward with moderate left and right
turns. However, depending on the
driving conditions and driving environ-
ment, registration may take some time
to complete.
■ Registering the position of each
wheel
1 Park the vehicle in a safe place, turn
the power switch off and wait 15
minutes or more.
2 Start the hybrid system.
The wheel position registration procedure
cannot be performed while the vehicle is
moving.
NOTICE
■ Repairing or replacing tires, wheels,
tire pressure warning valves, trans-
mitters and tire valve caps
● When removing or fitting the wheels,
tires or the tire pressure warning
valves and transmitters, contact any
authorized Lexus retailer or Lexus
authorized repairer, or any reliable
repairer as the tire pressure warning
valves and transmitters may be dam-
aged if not handled correctly.
● Make sure to install the tire valve caps.
If the tire valve caps are not installed,
water could enter the tire pressure
warning valves, corrode the valve, and
cause sticking and air leaks.
● When replacing tire valve caps, do not
use tire valve caps other than those
specified. The cap may become stuck.
■ To avoid damage to the tire pressure
warning valves and transmitters
(vehicles with an emergency tire
puncture repair kit)
When a tire is repaired with liquid seal-
ants, the tire pressure warning valve and
transmitter may not operate properly. If a
liquid sealant is used, contact any autho-
rized Lexus retailer or Lexus authorized
repairer, or any reliable repairer or other
qualified service shop as soon as possi-
ble. Make sure to replace the tire pres-
sure warning valve and transmitter when
replacing the tire. (P.459)
Registering the position of each
wheel
461
6
6-3. Do-it-yourself maintenance
Maintenance and care
3 Select on the Center Display.
4 Select “Vehicle customise”.
5 Select “Tyre pressure”.
6 Select “Tyre rotation”.
7 Select “Continue”.
A message indicating that wheel position
registration is being performed will be dis-
played on the multi-information display. “--
-” will be displayed for the tire inflation
pressure of each tire and wheel position
registration will begin.
8 Drive straight (with occasional left
and right turns) at approximately
40 km/h (25 mph) or more for
approximately 10 to 30 minutes.
When wheel position registration is com-
plete, a message indicating that registra-
tion has been completed and the inflation
pressure of each tire will be displayed on
the multi-information display.
Even if it is not possible to drive continu-
ously at approximately 40 km/h (25 mph)
or more, registration can be completed by
driving for a long time. However, if regis-
tration does not complete after driving for 1
hour or more, park the vehicle in a safe
place and leave it with the power switch in
ON for approximately 15 minutes or more,
and then perform the driving procedure
again.
■ When performing wheel position regis-
tration
● Normally, wheel position registration can
be completed within approximately 30
minutes.
● Wheel position registration is performed
while driving at a vehicle speed of
approximately 40 km/h (25 mph) or
more.
■ Wheel position registration procedure
● If the power switch is turned off while reg-
istering the wheel position, the next time
the power switch is turned to ON, the
wheel position registration will resume
and it will not be necessary to restart the
procedure.
● While the position of each wheel is being
determined and the inflation pressures
are not being displayed, if the inflation
pressure of a tire drops, the tire pressure
warning light will come on.
■ If the wheel position cannot be regis-
tered easily
● In the following situations, wheel position
registration may take longer than usual to
be completed or may not be possible.
• Vehicle is not driven at approximately 40
km/h (25 mph) or more
• Vehicle is driven on unpaved roads
● If wheel position registration does not
complete after driving for 1 hour or more,
park the vehicle in a safe place for
approximately 15 minutes and then drive
the vehicle again.
● If the vehicle is reversed during wheel
position registration, all data collected
until then will be cleared. Perform driving
again.
■ When you need to setting the tire
pressure
In the following situations, it will be nec-
essary to perform the tire inflation
pressure setting procedure of the tire
pressure warning system.
When the specified tire inflation
pressure has changed, such as due
to carried load, etc.
When the tire inflation pressure is
changed such as when the tire size
is changed.
If the tire inflation pressure has been
adjusted to the specified level, perform
the tire inflation setting procedure by
Setting the tire pressure
462
6-3. Do-it-yourself maintenance
selecting specified inflation pressure
on the Center Display. (P.462)
When the tire inflation pressure is to be
other than specified, such as when tires
other than the specified size are used,
etc., set the tire inflation pressure using
the current pressure. Make sure to
adjust the tire inflation pressure of each
tire to the appropriate level before
performing tire pressure setting. The
tire pressure warning system operates
based on this tire inflation pressure.
(P.462)
■ Setting by selecting a specified tire
inflation pressure
1 Start the hybrid system.
The tire inflation pressure cannot be set
while the vehicle is moving.
2 Select on the Center Display.
3 Select “Vehicle customise”.
4 Select “Tyre pressure”.
5 Select “Set indicated air pressure”
and then select the desired front
and rear tire pressures.
6 Select “OK”.
The tire pressure warning light will slowly
blink 3 times.
After setting the tire inflation pressure, a
message indicating that setting has been
completed will be displayed on the multi-
information display.
■ Setting using the current tire infla-
tion pressure
1 Adjust the tire inflation pressure of
each tire to the appropriate level.
Make sure to adjust the tire inflation pres-
sure with the tires cold.
2 Start the hybrid system.
The tire inflation pressure cannot be set
while the vehicle is moving.
3 Select on the Center Display.
4 Select “Vehicle customise”.
5 Select “Tyre pressure”.
6 Select “Set current air pressure”.
7 Select “Continue”.
The tire pressure warning light will slowly
blink 3 times and a message indicating that
tire inflation pressure is being set will be
displayed on the multi-information display.
After setting the tire inflation pressure, a
message indicating that setting has been
completed will be displayed on the multi-
463
6
6-3. Do-it-yourself maintenance
Maintenance and care
information display.
■ Warning performance of the tire pres-
sure warning system (Setting using the
current tire inflation pressure)
● When performing the tire pressure set-
ting using the current tire inflation pres-
sure, the warning timing of the tire
pressure warning system will vary
according to the conditions under which
tire pressure setting was performed.
Therefore, a warning may be output even
if the tire inflation pressure drops slightly
or if the tire inflation pressure increases
above that when the tire inflation pres-
sure was set.
● Make sure to perform the tire pressure
setting procedure after adjusting the tire
inflation pressure. Also, make sure the
tires are cold before performing the tire
pressure setting procedure or adjusting
the tire inflation pressure.
■ Tire inflation pressure setting proce-
dure (Setting using the current tire infla-
tion pressure)
● If the power switch is turned off while set-
ting the tire inflation pressure, the next
time the power switch is turned to ON,
the setting procedure will resume and it
will not be necessary to restart the proce-
dure.
● If the tire inflation pressure setting proce-
dure is started unnecessarily, adjust the
tire inflation pressure to the specified
level with the tires cold and then perform
setting by selecting a specified tire infla-
tion pressure, or perform the tire inflation
pressure setting procedure with the cur-
rent tire inflation pressure.
■ If the tire inflation pressure cannot be
set easily
● Normally, it takes approximately 3 min-
utes to complete the setting procedure to
the current tire inflation pressure.
● If the tire pressure warning light does not
blink 3 times when starting the tire infla-
tion pressure setting procedure, the pro-
cedure may not have started. Perform
the procedure again from the beginning.
● If tire inflation pressure setting procedure
cannot be completed after performing
the above procedure, contact any autho-
rized Lexus retailer or Lexus authorized
repairer, or any reliable repairer.
■ When to register ID codes
The tire pressure warning valve and
transmitter is equipped with a unique
ID code. When new tire pressure
warning valves and transmitters are
installed, new ID codes must be regis-
tered in the tire pressure warning com-
puter.
■ How to registration ID code
Before performing ID code registra-
tion, make sure that no wheels with tire
pressure warning valve and transmit-
ters installed are near the vehicle.
WARNING
■ When setting using the current tire
inflation pressure
Make sure to adjust the tire inflation
pressure of each tire to the appropriate
level before performing tire pressure
setting. Otherwise, the tire pressure
warning light may not illuminate even if
the tire inflation pressure drops or may
illuminate even though the tire inflation
pressure is normal.
Registering ID codes
464
6-3. Do-it-yourself maintenance
1 Park the vehicle in a safe place, turn
the power switch off and wait 15
minutes or more.
2 Start the hybrid system.
The ID code registration procedure can-
not be performed while the vehicle is mov-
ing.
3 Select on the Center Display.
4 Select “Vehicle customise”.
5 Select “Tyre pressure”.
6 Check if the desired wheel set (“Set
1” or “Set 2”) is displayed.
ID codes will be registered to the displayed
wheel set.
To change the wheel set to be registered,
select the displayed set, and then select the
wheel set you wish to register.
If ID codes have already been registered
for that wheel set, the tire pressure warning
light will slowly blink 3 times, and a mes-
sage indicating that change is occurring
will be displayed on the multi-information
display.
7 Select “New tyre registration”.
8 Select “Continue”.
The tire pressure warning light will slowly
blink 3 times and a message indicating that
ID code registration is being performed
will be displayed on the multi-information
display. Wheel set changing will be can-
celed and registration will begin.
When registration is being performed, the
tire pressure warning light will blink for
approximately 1 minute then illuminate and
“---” will be displayed for the inflation pres-
sure of each tire on the multi-information
display.
9 Drive straight (with occasional left
and right turns) at approximately
40 km/h (25 mph) or more for
approximately 10 to 30 minutes.
When registration is complete, the tire
pressure warning light will turn off and a
message indicating that registration has
been completed will be displayed on the
multi-information display.
Registration may take longer than normal
to complete if the vehicle speed cannot be
maintained at approximately 40 km/h (25
mph) or more. If registration cannot be
completed after driving for 1 hour or more,
perform the registration procedure again
from the beginning.
10 If the tire inflation pressure of the
wheel set installed differs from that
of the previous set, it will be neces-
sary to perform the tire inflation
pressure setting procedure of the
tire pressure warning system.
(P.461)
If the specified tire inflation pressure is the
same, it will not be necessary to perform
the tire inflation pressure setting proce-
dure.
465
6
6-3. Do-it-yourself maintenance
Maintenance and care
■ When registering ID codes
● Normally, wheel position registration can
be completed within approximately 30
minutes.
● ID code registration is performed while
driving at a vehicle speed of approxi-
mately 40 km/h (25 mph) or more.
● ID codes can be registered by yourself,
but depending on the driving conditions
and driving environment, registration
may take some time to complete.
● When using a wheel set which all of the
ID codes have already been registered,
the wheel set can be changed in a short
amount of time. (P.465)
■ If ID codes are not registered easily
● In the following situations, ID code regis-
tration may take longer than usual to be
completed or may not be possible.
• When the vehicle has not been parked
for approximately 15 minutes or more
before being driven
• Vehicle is not driven at approximately 40
km/h (25 mph) or more
• Vehicle is driven on unpaved roads
• Vehicle is driven near other vehicles and
system cannot recognize tire pressure
warning valve and transmitters of your
vehicle over those of other vehicles
• Wheel with tire pressure warning valve
and transmitter installed is inside or near
the vehicle
● If the vehicle is reversed during registra-
tion, all data collected until then will be
cleared. Perform driving again.
● If registration does not complete after
driving for 1 hour or more, perform the ID
code registration procedure again from
the beginning.
● If the tire pressure warning light does not
blink 3 times when starting ID code reg-
istration procedure, the procedure may
not have started. Perform the procedure
again from the beginning.
● If the ID codes cannot be registered even
when performing the above procedure,
contact any authorized Lexus retailer or
Lexus authorized repairer, or any reliable
repairer.
To cancel ID code registration after it
has been started, select “New tyre reg-
istration” again on the Center Display.
If ID code registration has been canceled,
the tire pressure warning light will turn off.
If the warning light does not turn off, ID
code registration may not have been
cancelled correctly. To cancel registration,
select “New tyre registration” again on the
Center Display.
Your vehicle is equipped with a tire
pressure warning system with a func-
tion to register two sets of ID codes.
This allows for registration of a second
wheel set, for example a winter set.
The wheel set can be changed only
if a second wheel set has been reg-
istered to the system. If a second
wheel set has not been registered,
“Set 2 (Unregistered)” will be dis-
played and it will not be possible to
change to the selected wheel set.
ID codes can be registered by yourself.
(P.463)
Only a change between both regis-
tered wheel set is possible, mixing
between these wheel sets is not sup-
ported.
While registering ID codes, it may
not be possible to change between
wheel sets normally. Cancel regis-
tration before changing between
Canceling ID code registration
Selecting wheel set
466
6-3. Do-it-yourself maintenance
wheel sets.
■ Changing ID codes between dif-
ferent wheel sets
1 Install the desired wheel set.
2 Select on the Center Display.
3 Select “Vehicle customise”.
4 Select “Tyre pressure”.
5 Select the wheel set (“Set 1” or “Set
2”) displayed for the set selection
setting.
6 Select the wheel set you wish to
register, and then select “OK”.
The tire pressure warning light will slowly
blink 3 times, a message indicating that
change is occurring will be displayed, and
the wheel set change will begin.
Wheel set change will begin and the tire
pressure warning light will blink for 1 min-
ute and then illuminate. Also, while the
change is being performed, “---” will be
displayed for the tire inflation pressure of
each tire on the multi-information display.
After approximately 2 minutes, the wheel
set change will complete, the tire pressure
warning light will turn off, and a completion
message will be displayed on the multi-
information display.
If changing does not complete after
approximately 4 minutes, a message indi-
cating that the change could not be com-
pleted will be displayed.
Check which wheel set is installed and per-
form the change procedure again from the
beginning.
7 If the specified tire inflation pres-
sure of the wheel set installed dif-
fers from that of the previous set, it
will be necessary to perform the
tire inflation pressure setting pro-
cedure of the tire pressure warning
system. (P.461)
If the specified tire inflation pressure is the
same, it will not be necessary to perform
the tire inflation pressure setting proce-
dure.
8 Register the position of each wheel.
(P.460)

Related Topics

Popular Owner Manuals