2019-2026 Lexus UX SUV Opening, closing and locking the doors User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Opening, closing and locking the doors for Your Lexus UX SUV First Generation (2019-2026)

120
3-2. Opening, closing and locking the doors
3-2.Opening, closing and locking t he doors
■ Smart access system with push-
button start
Carry the electronic key to enable this
function.
1 Grip the driver’s door handle to
unlock the door. Holding the
driver’s door handle for approxi-
mately 2 seconds unlocks all the
doors. Grip the front passenger
door handle to unlock all the
doors.
*
Make sure to touch the sensor on the back
of the handle.
The doors cannot be unlocked for 3 sec-
onds after the doors are locked.
*
: The door unlock settings can be
changed.
2 Touch the lock sensor (the indenta-
tion on the upper part of the front
door handle) to lock all the doors.
Check that the door is securely locked.
■ Wireless remote control
1 Locks all the doors
Check that the door is securely locked.
2 Unlocks all the doors
Pressing the button unlocks the driver’s
door. Pressing the button again within 3
seconds unlocks the other doors.
Press and hold to open the windows and
moon roof
*1, 2
*1
: If equipped
*2
: This setting must be customized at your
Lexus dealer.
■ Switching the door unlock function
It is possible to set which doors the entry
function unlocks using the wireless remote
control.
1 Turn the power switch off.
2 Cancel the intrusion sensor and tilt sen-
sor of the alarm system to prevent unin-
tended triggering of the alarm while
changing the settings. (P.74)
3 When the indicator light on the key sur-
face is not on, press and hold ,
or for approximately 5
seconds while pressing and holding
.
The setting changes each time an operation
is performed, as shown below. (When
changing the setting continuously, release
the buttons, wait for at least 5 seconds, and
repeat step
2.)
Side doors
Unlocking and locking the doors
from the outside
121
3-2. Opening, closing and locking the doors
3
Before driving
To prevent unintended triggering of the
alarm, unlock the doors using the wireless
remote control and open and close a door
once after the settings have been changed.
(If a door is not opened within 60 seconds
after is pressed, the doors will be
locked again and the alarm will automati-
cally be set.)
In a case that the alarm is triggered, imme-
diately stop the alarm. (P.72)
■ Locking the front doors from the outside
without a key
1 Push down the inside lock button.
(P.123)
2 Close the door.
The door cannot be locked if the power
switch is in ACC or ON, or the electronic
key is left inside the vehicle.
The key may not be detected correctly and
the door may be locked.
■ Impact detection door lock release sys-
tem
In the event that the vehicle is subject to a
strong impact, all the doors are unlocked.
Depending on the force of the impact or the
type of accident, however, the system may
not operate.
■ Operation signals
A buzzer sounds and the emergency flash-
ers flash to indicate that the doors have
been locked/unlocked. (Locked: Once;
Unlocked: Twice)
A buzzer sounds to indicate that all win-
dows are opening.
■ Security feature
If a door is not opened within approximately
60 seconds after the vehicle is unlocked,
the security feature automatically locks the
vehicle again.
■ When the door cannot be locked by the
lock sensor on the upper part of the
door handle
When the door cannot be locked even if the
lock sensor on the upper part of the door
handle is touched by a finger, touch the lock
sensor with the palm.
When gloves are being worn, remove the
gloves.
■ Open door warning buzzer
If an attempt to lock the doors is made when
a door is not fully closed, a buzzer sounds
continuously for 5 seconds. Fully close the
door to stop the buzzer, and lock the vehi-
cle once more.
■ Setting the alarm
Locking the doors will set the alarm system.
(P.72)
■ Conditions affecting the operation of
the smart access system with push-but-
ton start or wireless remote control
P.140
■ If the smart access system with push-
button start or the wireless remote con-
trol does not operate properly
● Use the mechanical key to lock and
unlock the doors. (P.430)
Multi-information
display/Beep
Unlocking function
Exterior: Beeps 3
times
Holding the driver’s
door handle unlocks
only the driver’s door.
Holding the front pas-
senger door handle
unlocks all the doors.
Exterior: Beeps
twice
Holding a front door
handle unlocks all the
doors.
122
3-2. Opening, closing and locking the doors
● Replace the key battery with a new one if
it is depleted. (P.392)
■ If the 12-volt battery is discharged
The doors cannot be locked and unlocked
using the smart access system with push-
button start or wireless remote control.
Lock or unlock the doors using the
mechanical key. (P.430)
■ Rear seat reminder function
● In order to remind you not to forget lug-
gage, etc. on the rear seat, when the
power switch is turned off after any of the
following conditions is met, a buzzer will
sound and a message will be displayed on
the multi-information display for approxi-
mately 6 seconds.
• The hybrid system is started within 10
minutes after opening and closing a rear
door.
• A rear door has been opened and closed
after the hybrid system was started.
However, if a rear door is opened and then
closed within approximately 2 seconds, the
rear seat reminder function may not oper-
ate.
● The rear seat reminder function deter-
mines that luggage, etc. has been placed
on a rear seat based on opening and
closing of a rear door. Therefore,
depending on the situation, the rear seat
reminder function may not operate and
you may still forget luggage, etc. on the
rear seat, or it may operate unnecessar-
ily.
● The rear seat reminder function can be
enabled/disabled. (P.469)
■ Customization
Settings (e.g. unlocking function using a
key) can be changed. (Customizable fea-
tures: P.462)
■ Door lock switches (to
lock/unlock)
1
Locks all the doors
WARNING
■ To prevent an accident
Observe the following precautions while
driving the vehicle.
Failure to do so may result in a door
opening and an occupant falling out,
resulting in death or serious injury.
● Ensure that all doors are properly
closed and locked.
● Do not pull the inside handle of the
doors while driving.
Be especially careful for the front
doors, as the doors may be opened
even if the inside lock buttons are in
locked position.
● Set the rear door child-protector locks
when children are seated in the rear
seats.
■ When opening or closing a door
Check the surroundings of the vehicle
such as whether the vehicle is on an
incline, whether there is enough space
for a door to open and whether a strong
wind is blowing. When opening or clos-
ing the door, hold the door handle tightly
to prepare for any unpredictable move-
ment.
Unlocking and locking the doors
from the inside
123
3-2. Opening, closing and locking the doors
3
Before driving
2 Unlocks all the doors
■ Inside lock buttons (to lock)
Push down the inside lock button to
lock the door.
■ Inside door handles (to unlock)
For the front doors
Pull the handle to unlock and open the
door.
When the door is unlocked, the inside lock
button will pop up.
For the rear doors
Pull the handle to unlock the door. Pull
the handle a second time to open the
door.
When the door is unlocked, the inside lock
button will pop up.
■ If a symbol indicating one or more doors
are open is shown on the multi-informa-
tion display
The hood or one or more of the doors are
not fully closed. The system also indicates
which doors are not fully closed. If the vehi-
cle reaches a speed of 3 mph (5 km/h), a
buzzer sounds to indicate that the door(s)
are not yet fully closed.
Make sure that the hood and all the doors
are closed.
The door cannot be opened from
inside the vehicle when the lock is set.
1 Unlock
2 Lock
These locks can be set to prevent children
from opening the rear doors. Push down
on each rear door switch to lock both rear
doors.
The following functions can be set or
canceled:
For instructions on customizing, refer to
P.460.
Rear door child-protector lock
Automatic door locking and
unlocking systems
124
3-2. Opening, closing and locking the doors
Function Operation
Speed linked door
locking function
All doors are auto-
matically locked
when vehicle speed
is approximately 12
mph (20 km/h) or
higher.
Shift position linked
door locking func-
tion
All doors are auto-
matically locked
when shifting the
shift position out of
P.
Shift position linked
door unlocking
function
All doors are auto-
matically unlocked
when shifting the
shift position to P.
Driver’s door linked
door unlocking
function
All doors are auto-
matically unlocked
when driver’s door is
opened within
approximately 45
seconds after turn-
ing the power switch
off.
Back door
The back door can be
locked/unlocked and
opened/closed by the following
procedures.
WARNING
Observe the following precautions.
Failure to do so may cause parts of the
body to be caught, resulting in death or
serious injury.
■ Before driving the vehicle
Make sure that the back door is fully
closed. If the back door is not fully closed,
it may open unexpectedly while driving
and hit nearby objects or luggage in the
luggage compartment may be thrown
out, causing an accident.
■ Caution while driving
● Keep the back door closed while driv-
ing.
If the back door is left open, it may hit
nearby objects while driving or lug-
gage may be unexpectedly thrown
out, causing an accident.
In addition, exhaust gases may enter
the vehicle, causing death or a serious
health hazard. Make sure to close the
back door before driving.
● Never let anyone sit in the luggage
compartment. In the event of sudden
braking, sudden swerving or a colli-
sion, they are susceptible to death or
serious injury.
■ When children are in the vehicle
Observe the following precautions.
Failure to do so may result in death or
serious injury.
● Do not allow children to play in the
luggage compartment.
If a child is accidentally locked in the
luggage compartment, they could
have heat exhaustion or other injuries.
125
3-2. Opening, closing and locking the doors
3
Before driving
WARNING
● Do not allow a child to open or close
the back door.
Doing so may cause the back door to
move unexpectedly, or cause the
child’s hands, arms, head, or neck to
be caught by the closing back door.
■ Operating the back door
Observe the following precautions.
Failure to do so may cause parts of the
body to be caught, resulting in death or
serious injury.
● Remove any heavy loads, such as
snow and ice, from the back door
before opening it. Failure to do so may
cause the back door to suddenly shut
again after it is opened.
● When opening or closing the back
door, thoroughly check to make sure
the surrounding area is safe.
● If anyone is in the vicinity, make sure
they are safe and let them know that
the back door is about to open or
close.
● Use caution when opening or closing
the back door in windy weather as it
may move abruptly in strong wind.
● Vehicles without power back door:
The back door may suddenly shut if it is
not opened fully. It is more difficult to
open or close the back door on an
incline than on a level surface, so
beware of the back door unexpectedly
opening or closing by itself. Make sure
that the back door is fully open and
secure before using the luggage com-
partment.
● Vehicles with power back door: The
back door may suddenly shut if it is not
opened fully, while on a steep incline.
Make sure that the back door is
secured before using the luggage
compartment.
● When closing the back door, take
extra care to prevent your fingers, etc.,
from being caught.
● When closing the back door, make
sure to press it lightly on its outer sur-
face. If the back door handle is used to
fully close the back door, it may result
in hands or arms being caught.
● Do not pull on the back door damper
stay (vehicles without power back
door) (P.127) or back door spindle
(vehicles with power back door)
(P.136) to close the back door, and
do not hang on the back door damper
stay (vehicles without power back
door) or back door spindle (vehicles
with power back door).
Doing so may cause hands to be
caught or the back door damper stay
(vehicles without power back door) or
back door spindle (vehicles with
power back door) to break, causing an
accident.
● If a bicycle carrier or similar heavy
object is attached to the back door, it
may suddenly shut again after being
opened, causing someone’s hands,
arms, head or neck to be caught and
injured. When installing an accessory
part to the back door, using a genuine
Lexus part is recommended.
126
3-2. Opening, closing and locking the doors
■ Smart access system with push-
button start
Carry the electronic key to enable this
function.
1 Locks all the doors
Check that the door is securely locked.
2 Unlocks all the doors
The doors cannot be unlocked for 3 sec-
onds after the doors are locked.
■ Wireless remote control
P.120
■ Door lock switch
P.122
■ Open
Raise the back door while pressing up
the back door opener switch.
■ Close
Lower the back door using the back
door handle, and make sure to push
the back door down from the outside
to close it.
■ Luggage compartment light
● The luggage compartment light turns on
when the back door is opened.
● If the luggage compartment light is left on
when the power switch is turned off, the
light will go off automatically after 20
minutes.
■ If the back door opener is inoperative
The back door can be unlocked from the
inside.
1 Remove the cover.
To protect the cover, place a rag between
the flathead screwdriver and the cover as
shown in the illustration.
Unlocking and locking the back
door from the outside
Unlocking and locking the back
door from the inside
Opening/closing the back door
(vehicles without power back
door)
127
3-2. Opening, closing and locking the doors
3
Before driving
2 Move the lever.
■ Opening/closing the back door
using the wireless remote control
Press the switch for 1 second.
If the back door is locked, unlock it
before operating the power back door.
■ Opening/closing the back door
from the inside
Press the switch for 1 second.
A buzzer sounds and the back door auto-
matically opens and closes.
Pressing the switch while the back door is
opening/closing stops the operation.
When the switch is pressed again for 1 sec-
ond during the halted operation, the back
door will perform the reverse operation.
■ Opening/closing the back door
from the outside
Open
NOTICE
■ Back door damper stays
The back door is equipped with damper
stays that hold the back door in
place.
Observe the following precautions.
Failure to do so may cause damage to
the back door damper stay resulting
in malfunction.
● Do not attach any foreign objects,
such as stickers, plastic sheets, or
adhesives to the damper stay rod.
● Do not touch the damper stay rod with
gloves or other fabric items.
● Do not attach any accessories other
than genuine Lexus parts to the back
door.
● Do not place your hand on the damper
stay or apply lateral forces to it.
A
A
Opening/closing the back door
(vehicles with power back door)
128
3-2. Opening, closing and locking the doors
When the back door is unlocked: Press the
back door opener switch.
When the back door is locked: While car-
rying the electronic key on your person,
press the back door opener switch.
A buzzer sounds and the back door auto-
matically opens.
Pressing the switch while the back door is
opening stops the operation.
Close
Press the switch on the lower part
of the back door.
A buzzer sounds and the back door auto-
matically closes.
Pressing the switch while the back
door is closing stops the operation.
Pressing the switch again will open
the back door automatically.
Close the back door and lock all
doors after moving away from the
back door (close & lock [Walk-
Away] function)
1 Close all of the doors except the
back door, carrying an electronic
key and press the switch on
the lower part of the back door.
A different buzzer than the normal one will
sound and the close & lock (Walk-Away)
function will go into standby.
2 While the buzzer is sounding, move
away from the back door.
When the sensor detects that you are
away from the back door, the buzzer will
sound and the emergency flashers (if
equipped) will flash. Depending on the
direction of moving away from the back
door, the location and how to hold the
electronic key or circumstances, it may not
be detected properly.
All the doors other than the back door will
be locked, and after the back door is
closed, the back door will also be locked.
When all the doors have been closed and
locked, the buzzer (if equipped) will sound
and the emergency flashers will flash.
(P.121)
The standby state is canceled if you do not
move away from the back door for 30 sec-
onds. To operate the function again, per-
form the procedure again from the
beginning.
If you approach the back door carrying the
electronic key, the back door operation
will stop, all the doors will be unlocked, and
the buzzer (if equipped) will sound and the
emergency flashers will flash. (P.121)
If the switch is pressed after the
back door operation has stopped, the
close & lock (Walk-Away) function will go
129
3-2. Opening, closing and locking the doors
3
Before driving
into standby again.
Close the back door and lock all
doors (close & lock function)
*
*
: These settings must be customized at
your Lexus dealer.
Close all of the doors except the
back door, carrying an electronic
key and press the switch on
the lower part of the back door.
A different buzzer than the normal one will
sound and the power back door will begin
closing automatically. When the power
back door is closed, all of the doors will
lock simultaneously and operation signals
will indicate that all of the doors have been
locked.
If the switch is pressed while the
power back door is closing, the operation
will stop.
Pressing the switch again will close
the power back door automatically.
■ Closing the back door using the
back door handle
Lower the back door using the back
door handle, then a buzzer sounds and
the back door automatically closes.
■ Hands Free Power Back Door
1 While carrying an electronic key,
stand within the smart access sys-
tem with push-button start opera-
tion range, approximately 19.7 to
27.6 in. (50 to 70 cm) from the
rear bumper.
Kick sensor
Hands Free Power Back Door
operation detection area
Smart access system with push-
button start operation detection
area (P.139)
2 Perform a kick operation by mov-
ing your foot to within approxi-
mately 3.9 in. (10 cm) of the rear
bumper, and then pulling your foot
back after the buzzer sounds.
• Perform the entire kick operation
within 1 second.
• The Hands Free Power Back Door
A
B
C
130
3-2. Opening, closing and locking the doors
will not start operating while a foot is
detected under the rear bumper.
• Operate the Hands Free Power
Back Door without contacting the
rear bumper with your foot.
• If another electronic key is in the
cabin or luggage compartment, it
may take slightly longer than normal
for the operation to occur.
• If the buzzer sounds twice, perform
a kick operation again.
Kick sensor
Hands Free Power Back Door
operation detection area
3 When the kick sensor detects that
your foot is pulled back, a buzzer
will sound and the back door will
automatically fully open/close.
If a foot is moved under the rear bumper
while the back door is operating, the back
door will stop moving.
■ Closing and locking the back door
after moving away from the back
door using the kick sensor (Hands
Free close & lock [Walk-Away]
function)
*
*
: These settings must be customized at
your Lexus dealer.
The Hands Free Power Back Door
enables automatic closing and locking
of the power back door by putting your
foot near the right lower part of the
rear bumper, moving it away from the
rear bumper, and moving away from
the back door. When operating the
Hands Free Power Back Door, make
sure that the power switch is in OFF,
the kick sensor operation is enabled
(P.137) and you are carrying an
electronic key.
1 While carrying an electronic key,
stand within the smart access sys-
tem with push-button start opera-
tion range, approximately 11.8 to
19.7 in. (30 to 50 cm) from the rear
bumper.
Kick sensor
Hands Free Power Back Door
operation detection area
Smart access system with push-
button start operation detection
area (P.139)
2 Perform a kick operation by mov-
ing your foot to within approxi-
mately 3.9 in. (10 cm) of the rear
bumper and then pulling it back.
Perform the entire kick operation within 1
second.
The back door will not start operating
while a foot is detected under the rear
A
B
A
B
C
131
3-2. Opening, closing and locking the doors
3
Before driving
bumper.
Operate the Hands Free Power Back
Door without contacting the rear bumper
with your foot.
If another electronic key is in the cabin or
luggage compartment, it may take slightly
longer than normal for the operation to
occur.
Kick sensor
Hands Free Power Back Door
operation detection area
3 When the kick sensor detects that
your foot is pulled back, a different
buzzer than the normal one will
sound and the Hands Free close &
lock (Walk-Away) function will go
into standby.
4 While the buzzer is sounding, move
away from the back door.
When the sensor detects that you are
away from the back door, the buzzer will
sound and the emergency flashers (if
equipped) will flash. Depending on the
direction of moving away from the back
door, the location and how to hold the
electronic key or circumstances, it may not
be detected properly.
All the doors other than the back door will
be locked, and after the back door is
closed, the back door will also be locked.
When all the doors have been closed and
locked, the buzzer (if equipped) will sound
and the emergency flashers will flash.
(P.121)
The standby state is canceled if you do not
move away from the back door in 30 sec-
onds. To operate the function again, per-
form the procedure again from the
beginning.
If you approach the back door carrying the
electronic key, the back door operation
will stop, all the doors will be unlocked, and
the buzzer (if equipped) will sound and the
emergency flashers will flash. (P.121)
If the power back door is operated after
the back door operation has stopped, the
Hands Free close & lock (Walk-Away)
function will go into standby again.
■ Luggage compartment light
● The luggage compartment light turns on
when the back door is opened.
● If the luggage compartment light is left on
when the power switch is turned off, the
light will go off automatically after 20
minutes.
■ Power back door operating conditions
With the power back door operations set to
ON, it can automatically open and close for
the following conditions:
● The power back door is unlocked. How-
ever, the power back door will operate if
it is locked, in the following situations:
• When the electronic key is being carried
and the power back door opener switch
is pressed
• When the wireless remote control is
used
*
● When the power switch is in ON, in addi-
tion to the above for the opening opera-
tions, the back door operates for any of
the following conditions:
• Parking brake is engaged
• The brake pedal is depressed
• The shift position is in P
*
: When configured with the customization
function so that it can be operated after
being unlocked, operate the back door
after it has been unlocked.
■ Hands Free Power Back Door operat-
ing conditions
● When the Hands Free Power Back Door
operation setting is turned on
A
B
132
3-2. Opening, closing and locking the doors
● When an electronic key is carried within
the operation range
■ Back door closer
In the event that the back door is left slightly
open, the back door closer will automati-
cally close it to the fully closed position.
Whatever the state of the power switch, the
back door closer operates.
■ Operation of the power back door
● A buzzer sounds and the emergency
flashers flash twice to indicate that the
back door is opening/closing.
● When the power back door operations
are OFF, the power back door does not
operate but it can be opened and closed
by hand.
● When the power back door automati-
cally opens, if an abnormality due to peo-
ple or objects is detected, operation will
stop.
■ Back door reserve lock function
This function reserves locking of all doors
beforehand, when the power back door is
open.
When the following procedure is per-
formed, all the doors except the power
back door are locked and then power back
door will also be locked at the same time it
is closed.
1 Close all doors, except the back door.
2 During the power back door closing
operation, lock the doors using the
smart access system with push-button
start (P.120) or the wireless remote
control. (P.116)
A buzzer sounds and the emergency flash-
ers flash to indicate that all the doors have
been closed and locked.
Before leaving the vehicle, make sure that
all the doors are closed and locked. The
doors may not be locked due to the jam
protection function or door lock prevention
function.
■ Close & lock (Walk-Away) function
operating conditions
This function can be operated when all of
the following conditions are met:
● Close & lock (Walk-Away) function is
enabled.
● An electronic key is not detected within
the vehicle.
● All of the doors other than the back door
are closed.
● The power switch is in OFF.
● The electronic key is within the effective
range (detection areas).
■ Situations in which the close & lock
(Walk-Away) function may not operate
properly
In the following situations, the function may
not operate properly:
● When the smart access system with
push-button start does not operate prop-
erly.
● When the close & lock function does not
operate properly.
● When moving away from the back door
while the close & lock (Walk-Away)
function is in the standby state.
■ Close & lock function
*
operating condi-
tions
This function can be operated when all of
the following conditions are met:
● An electronic key is not detected within
the vehicle.
● All of the doors other than the power
back door are closed.
● The power switch is in OFF.
*
: These settings must be customized at
your Lexus dealer.
■ Situations in which the close & lock
function
*
may not operate properly
In the following situations, the close & lock
function may not operate properly:
● If the switch on the lower part of
the power back door (P.127) is
pressed by a hand which is holding an
electronic key
● If the switch on the lower part of
the power back door (P.127) is
pressed when the electronic key is in a
133
3-2. Opening, closing and locking the doors
3
Before driving
bag, etc. that is placed on the ground
● If the switch on the lower part of
the power back door (P.127) is
pressed with the electronic key not near
the vehicle
*
: These settings must be customized at
your Lexus dealer.
● A foot is put near the right lower part of
the rear bumper and moved away from
the rear bumper.
The power back door may also be oper-
ated by putting a hand, an elbow, a knee,
etc. near the right lower part of the rear
bumper and moving it away from the rear
bumper. Make sure to put it close
enough to the right lower part of the rear
bumper.
■ Situations in which the Hands Free
Power Back Door may not operate
properly
In the following situations, the Hands Free
Power Back Door may not operate prop-
erly:
● When a foot remains under the rear
bumper
● If the rear bumper is strongly hit with a
foot or is touched for a while
If the rear bumper has been touched for a
while, wait for a short time before
attempting to operate the Hands Free
Power Back Door again.
● When operated while a person is too
close to the rear bumper
● When an external radio wave source
interferes with the communication
between the electronic key and the vehi-
cle (P.140)
● When the vehicle is parked near an elec-
trical noise source or a metallic object
which affects the sensitivity of the Hands
Free Power Back Door, such as a pay
parking spot, gas station, electrically
heated road, fluorescent light or iron
plate
● When the vehicle is near a TV tower,
electric power plant, radio station, large
display, airport or other facility that gen-
erates strong radio waves or electrical
noise
● When a large amount of water is applied
to the rear bumper, such as when the
vehicle is being washed or in heavy rain
● When mud, snow, ice, etc. is attached to
the rear bumper
● When the vehicle has been parked for a
while near objects that may move and
contact the rear bumper, such as plants
● When an accessory is installed to the rear
bumper
If an accessory has been installed, turn
the Hands Free Power Back Door opera-
tion setting off.
■ Preventing unintentional operation of
the Hands Free Power Back Door
When an electronic key is in the operation
range, the Hands Free Power Back Door
may operate unintentionally, so be careful
in the following situations.
● When a large amount of water is applied
to the rear bumper, such as when the
vehicle is being washed or in heavy rain
● When dirt is wiped off the rear bumper
● When a small animal or small object, such
as a ball, moves under the rear bumper
● When an object is moved from under the
rear bumper
● If someone is swinging their legs while sit-
ting on the rear bumper
● If the legs or another part of someone’s
body contacts the rear bumper while
passing by the vehicle
● When the vehicle is parked near an elec-
trical noise source which affects the sen-
sitivity of the Hands Free Power Back
Door, such as a pay parking spot, gas sta-
tion, electrically heated road, or fluores-
cent light
● When the vehicle is near a TV tower,
electric power plant, radio station, large
display, airport or other facility that gen-
erates strong radio waves or electrical
noise
● When the vehicle is parked in a place
where objects such as plants are near the
rear bumper
134
3-2. Opening, closing and locking the doors
● If luggage, etc. is set near the rear
bumper
● If accessories or a vehicle cover is
installed/removed near the rear bumper
● When the vehicle is being towed
To prevent unintentional operation, turn the
Hands Free Power Back Door operation
setting off.
■ Hands Free close & lock (Walk-Away)
function operating conditions
This function can be operated when all of
the following conditions are met:
● Hands Free close & lock (Walk-Away)
function is enabled
*
.
● Hands Free Power Back Door is
enabled.
● An electronic key is not detected within
the vehicle.
● All of the doors other than the back door
are closed.
● The power switch is in OFF.
● The electronic key is within the effective
range (detection areas).
*
: These settings must be customized at
your Lexus dealer.
■ Situations in which the Hands Free close
& lock (Walk-Away) function
*
may not
operate properly
In the following situations, the function may
not operate properly:
● When the smart access system with
push-button start does not operate prop-
erly.
● When the close & lock function does not
operate properly.
● When moving away from the back door
while the Hands Free close & lock (Walk-
Away) function is in the standby state.
● When the Hands Free Power Back Door
does not operate properly.
*
: These settings must be customized at
your Lexus dealer.
■ When reconnecting the 12-volt battery
To enable the power back door to operate
properly, close the back door manually.
■ Jam protection function
Sensors are installed in the right and left
sides of the power back door. When the
door is automatically closing and the sen-
sors are pushed due to an object being
clamped, etc., the jam protection function
operates.
From that position the door automatically
moves a little in the opposite direction and
then the function stops.
■ If the back door opener is inoperative
The back door can be unlocked from the
inside.
1 Remove the cover.
To protect the cover, place a rag between
the flathead screwdriver and the cover as
shown in the illustration.
2 Move the lever.
135
3-2. Opening, closing and locking the doors
3
Before driving
■ Customization
Some functions can be customized. (Cus-
tomizable features: P.462)
WARNING
■ Back door closer
● In the event that the back door is left
slightly open, the back door closer will
automatically close it to the fully closed
position. It takes several seconds
before the back door closer begins to
operate. Be careful not to catch fingers
or anything else in the back door, as
this may cause bone fractures or other
serious injuries.
● Be careful not to catch fingers or any-
thing else when using the back door
closer as it still operates when the
power back door system is canceled.
■ Power back door
Observe the following precautions when
operating the power back door.
Failure to do so may cause death or seri-
ous injury.
● Check the safety of the surrounding
area to make sure there are no obsta-
cles or anything that could cause any
of your belongings to get caught.
● If anyone is in the vicinity, make sure
they are safe and let them know that
the back door is about to open or
close.
● If the power back door system is dis-
abled, while the back door is operating
automatically, the automatic opera-
tion is stopped. The back door then
has to be operated manually. Take
extra care in this situation, as the back
door may open or close suddenly.
● If the operating conditions of the
power back door (P.131) are no lon-
ger met, a buzzer may sound and the
back door may stop opening or clos-
ing. The back door then has to be
operated manually. Take extra care
when on an incline, as the back door
may open or close abruptly.
● On an incline, the back door may sud-
denly shut after it opens. Make sure
the back door is fully open and secure.
● In the following situations, the power
back door may detect an abnormality
and automatic operation may be
stopped. In this case, the back door
has to be operated manually. Take
extra care in this situation, as the back
door may open or close suddenly.
• When the back door contacts an
obstacle
• When the 12-volt battery voltage sud-
denly drops, such as when the power
switch is turned to ON or the hybrid
system is started during automatic
operation
● If a bicycle carrier or similar heavy
object is attached to the back door, the
power back door may not operate,
causing itself to malfunction, or the
back door may suddenly shut again
after being opened, causing some-
one’s hands, arms, head or neck to be
caught and injured. When installing an
accessory part to the back door, using
a genuine Lexus part is recommended.
136
3-2. Opening, closing and locking the doors
WARNING
■ Jam protection function
Observe the following precautions.
Failure to do so may cause death or seri-
ous injury.
● Never use any part of your body to
intentionally activate the jam protec-
tion function.
● The jam protection function may not
work if something gets caught just
before the back door fully closes. Be
careful not to get fingers caught or
anything else.
● The jam protection function may not
work depending on the shape of the
object that is caught. Be careful not to
catch fingers or anything else.
■ Hands Free Power Back Door
Observe the following precautions.
Failure to do so may cause death or seri-
ous injury.
● Check the safety of the surrounding
area to make sure there are no obsta-
cles or anything that could cause any
of your belongings to get caught.
● Exhaust gases cause the exhaust pipes
to become quite hot. When operating
the Hands Free Power Back Door, be
careful not to touch the exhaust pipe.
● Do not operate the Hands Free Power
Back Door if there is little space under
the rear bumper.
■ Close & lock (Walk-Away) function
and Hands Free close & lock (Walk-
Away) function
*
*
: These settings must be customized at
your Lexus dealer.
The back door starts to close automati-
cally when leaving the back door. Check
the safety of the surrounding area to
make sure there are no obstacles or any-
thing that could cause any of your
belongings to get caught.
NOTICE
■ Back door spindles
The back door is equipped with spindles
that hold the back door in place.
Observe the following precautions.
Failure to do so may cause damage to
the back door spindle , resulting in
malfunction.
● Do not attach any foreign objects,
such as stickers, plastic sheets, or
adhesives to the spindle rod.
● Do not touch the spindle rod with
gloves or other fabric items.
● Do not attach any accessories other
than genuine Lexus parts to the power
back door.
● Do not place your hand on the spindle
or apply lateral forces to it.
■ To prevent back door closer malfunc-
tion
Do not apply excessive force to the back
door while the back door closer is oper-
ating. Applying excessive force may
cause the back door closer to malfunc-
tion.
■ To prevent damage to the power
back door
● Make sure that there is no ice between
the back door and frame that would
prevent movement of the back door.
Operating the power back door when
excessive load is present on the back
door may cause a malfunction.
A
A
137
3-2. Opening, closing and locking the doors
3
Before driving
The settings of the power back door
system can be changed on the center
display.
If the power back door is disabled, it will
remain disabled unless it is enabled on the
multi-information display. (It will not be
enabled even when the power switch is
turned off and then back to ON.)
The open position of the power back
door can be adjusted.
1
Stop the back door in the desirable
position. (P.127)
NOTICE
● Do not apply excessive force to the
back door while the power back door
is operating.
● Take care not to damage the sensors
(installed on the right and left edges of
the power back door) (P.134) with a
knife or other sharp object. If the sen-
sor is disconnected, the power back
door will not close automatically.
■ Close & lock function
*
When closing the power back door
using the close & lock function, a differ-
ent buzzer than the normal one will
sound before the operation begins.
To check that the operation has started
correctly, check that a different buzzer
than the normal one has sounded.
Additionally, when the power back door
is fully closed and locked, operation sig-
nals will indicate that all of the doors have
been locked.
Before leaving the vehicle, make sure
that the operation signals have operated
and that all of the doors are locked.
*
: These settings must be customized at
your Lexus dealer.
■ Hands Free Power Back Door pre-
cautions
Observe the following to ensure that the
power back door function operates
properly:
● Do not apply coatings that have a rain
clearing (hydrophilic) effect, or other
coatings, to the lower center part of
the rear bumper.
● Do not subject the rear bumper to a
strong impact.
If the rear bumper has been subjected
to a strong impact, the Hands Free
Power Back Door may not operate
properly. If the Hands Free Power
Back Door does not operate in the fol-
lowing situations, have the vehicle
inspected by your Lexus dealer.
• The kick sensor or its surrounding area
has been subjected to a strong impact.
• The lower center part of the rear
bumper is scratched or damaged.
● Do not disassemble the rear bumper.
● Do not attach stickers to the rear
bumper.
● Do not paint the rear bumper.
Changing settings of the power
back door system (vehicles with
power back door)
Adjusting the open position of
the back door (vehicles with
power back door)
138
3-2. Opening, closing and locking the doors
2 Press and hold the power back
door switch on the back door for 2
seconds.
• When the settings are completed,
the buzzer sounds 4 times.
• When opening the back door the
next time, the back door will stop at
that position.
■ Returning the back door automatic stop
position to the initial settings
Press and hold the power back door switch
on the back door for 7 seconds.
After the buzzer sounds 4 times, it sounds
twice more. When the power back door
does the opening operation the next time,
the door will open to the initial settings posi-
tion.
■ Antenna location
Antennas outside the cabin
Antennas inside the cabin
Operating the smart access system with
push-button start (P.138)
Smart access system with
push-button start
The following operations can be
performed simply by carrying the
electronic key (including the card
key) on your person, for example in
your pocket. The driver should
always carry the electronic key.
Locks and unlocks the doors
(P.120)
Locks and unlocks the back door
(P.124)
Starts the hybrid system
(P.177)
A
B
139
3-2. Opening, closing and locking the doors
3
Before driving
■ Effective range (areas within which the
electronic key is detected)
When locking or unlocking the doors
The system can be operated when the elec-
tronic key is within about 2.3 ft. (0.7 m) of
either of the outside front door handles and
back door opener switch. (Only the doors
detecting the key can be operated.)
When starting the hybrid system or
changing power switch modes
The system can be operated when the elec-
tronic key is inside the vehicle.
■ If an alarm sounds or a warning message
is displayed
An alarm sounds and warning message dis-
plays shown on the multi-information dis-
play are used to protect against
unexpected accidents or theft of the vehicle
resulting from erroneous operation. When
a warning message is displayed, take
appropriate measures based on the dis-
played message.
When only an alarm sounds, circumstances
and correction procedures are as follows.
● When an exterior alarm sounds once for
5 seconds
● When an interior alarm pings continu-
ously
■ If “Key Detected in Vehicle” is shown on
the multi-information display
An attempt was made to lock the doors
using the smart access system with push-
button start while the electronic key was still
inside the vehicle. Retrieve the electronic
key from the vehicle and lock the doors
again.
■ Battery-saving function
The battery-saving function will be acti-
vated in order to prevent the electronic key
battery and the 12-volt battery from being
discharged while the vehicle is not in opera-
tion for a long time.
● In the following situations, the smart
access system with push-button start may
take some time to unlock the doors. Also
the illuminated entry system may not
operate properly.
• The electronic key has been left in an
area of approximately 11.5 ft. (3.5 m) of
the outside of the vehicle for 40 seconds
or longer.
• The smart access system with push-but-
ton start has not been used for 5 days or
longer.
● If the smart access system with push-but-
ton start has not been used for 14 days or
longer, the doors cannot be unlocked at
any doors except the driver’s door. In this
case, take hold of the driver’s door han-
dle, or use the wireless remote control or
the mechanical key, to unlock the doors.
Situation
Correction proce-
dure
An attempt was
made to lock the
vehicle while a door
was open.
Close all of the
doors and lock the
doors again.
A
B
Situation
Correction proce-
dure
The power switch
was turned to ACC
while the driver’s
door was open (or
the driver’s door was
opened while the
power switch was in
ACC).
Turn the power
switch to OFF and
close the driver’s
door.
140
3-2. Opening, closing and locking the doors
■ Turning an electronic key to battery-
saving mode
● When battery-saving mode is set, battery
depletion is minimized by stopping the
electronic key from receiving radio
waves.
Press twice while pressing and
holding .
Confirm that the electronic key indicator
flashes 4 times.
While the battery-saving mode is set, the
smart access system with push-button start
cannot be used. To cancel the function,
press any of the electronic key buttons.
● Electronic keys that will not be used for
long periods of time can be set to the bat-
tery-saving mode in advance.
■ When electronic key function stops
If the position of the electronic key has not
changed for a certain amount of time such
as when the electronic key is left some-
where, the function of the electronic key
stops to reduce depletion of the battery.
In this case, function can automatically be
restored by moving the position of the key
such as by lifting it up.
■ Conditions affecting operation
The smart access system with push-button
start uses weak radio waves. In the follow-
ing situations, the communication between
the electronic key and the vehicle may be
affected, preventing the smart access sys-
tem with push-button start, wireless remote
control and immobilizer system from oper-
ating properly.
● When the electronic key battery is
depleted
● Near a TV tower, electric power plant,
gas station, radio station, large display,
airport or other facility that generates
strong radio waves or electrical noise
● When the electronic key is in contact
with, or is covered by the following metal-
lic objects
• Cards to which aluminum foil is attached
• Cigarette boxes that have aluminum foil
inside
• Metallic wallets or bags
• Coins
• Hand warmers made of metal
• Media such as CDs and DVDs
● When other wireless key (that emits
radio waves) is being used nearby
● When carrying the electronic key
together with the following devices that
emit radio waves
• Portable radio, cellular phone, cordless
phone or other wireless communication
devices
• Another electronic key or a wireless key
that emits radio waves
• Personal computers or personal digital
assistants (PDAs)
• Digital audio players
• Portable game systems
● If window tint with a metallic content or
metallic objects are attached to the rear
window
● When the electronic key is placed near a
battery charger or electronic devices
● When the vehicle is parked in a pay park-
ing spot where radio waves are emitted.
If the doors cannot be locked/unlocked
using the smart access system with push-
button start, lock/unlock the doors by per-
forming any of the following:
● Bring the electronic key close to either
front door handle and operate the entry
function.
● Operate the wireless remote control.
If the doors cannot be locked/unlocked
using the above methods, use the mechani-
cal key. (P.430)
If the hybrid system cannot be started using
the smart access system with push-button
start, refer to P.431.
141
3-2. Opening, closing and locking the doors
3
Before driving
■ Note for the entry function
● Even when the electronic key is within the
effective range (detection areas), the sys-
tem may not operate properly in the fol-
lowing cases:
• The electronic key is too close to the win-
dow or outside door handle, near the
ground, or in a high place when the doors
are locked or unlocked.
• The electronic key is on the instrument
panel, luggage compartment or floor, or
in the door pockets or glove box when
the hybrid system is started or power
switch modes are changed.
• A person is between the vehicle and
electronic key, blocking radio waves
when the door is unlocked
● Do not leave the electronic key on top of
the instrument panel or near the door
pockets when exiting the vehicle.
Depending on the radio wave reception
conditions, it may be detected by the
antenna outside the cabin and the doors
will become lockable from the outside,
possibly trapping the electronic key
inside the vehicle.
● As long as the electronic key is within the
effective range, the doors may be locked
or unlocked by anyone. However, only
the doors detecting the electronic key
can be used to unlock the vehicle.
● Even if the electronic key is not inside the
vehicle, it may be possible to start the
hybrid system if the electronic key is near
the window.
● The doors may unlock if a large amount
of water splashes on the door handle,
such as in the rain or in a car wash when
the electronic key is within the effective
range. (The doors will automatically be
locked after approximately 60 seconds if
the doors are not opened and closed.)
● If the wireless remote control is used to
lock the doors when the electronic key is
near the vehicle, there is a possibility that
the door may not be unlocked by the
entry function. (Use the wireless remote
control to unlock the doors.)
● Touching the door lock sensor while
wearing gloves may delay or prevent
lock operation. Remove the gloves and
touch the lock sensor again.
● Some models: When the lock operation
is performed using the lock sensor, rec-
ognition signals will be shown up to two
consecutive times. After this, no recogni-
tion signals will be given.
● If the door handle becomes wet while the
electronic key is within the effective
range, the door may lock and unlock
repeatedly. In that case, follow the follow-
ing correction procedures to wash the
vehicle.
• Place the electronic key in a location 6 ft.
(2 m) or more away from the vehicle.
(Take care to ensure that the key is not
stolen.)
• Set the electronic key to battery-saving
mode to disable the smart access system
with push-button start. (P.140)
● If the electronic key is inside the vehicle
and a door handle becomes wet during a
car wash, a message may be shown on
the multi-information display and a
buzzer will sound outside the vehicle. To
turn off the alarm, lock all the doors.
● The lock sensor may not work properly if
it comes into contact with ice, snow, mud,
etc. Clean the lock sensor and attempt to
operate it again.
● A sudden approach to the effective
range or door handle may prevent the
doors from being unlocked. In this case,
return the door handle to the original
position and check that the doors unlock
before pulling the door handle again.
● If there is another electronic key in the
detection area, it may take slightly longer
to unlock the doors after the door handle
is gripped.
■ When the vehicle is not driven for
extended periods
● To prevent theft of the vehicle, do not
leave the electronic key within 6 ft. (2 m)
of the vehicle.
● The smart access system with push-but-
ton start can be deactivated in advance.
(P.460)
● Battery-saving mode can reduce the
power consumption of electronic keys.
(P.140)
142
3-2. Opening, closing and locking the doors
■ To operate the system properly
Make sure to carry the electronic key when
operating the system. Do not get the elec-
tronic key too close to the vehicle when
operating the system from the outside of
the vehicle.
Depending on the position and holding
condition of the electronic key, the key may
not be detected correctly and the system
may not operate properly. (The alarm may
go off accidentally, or the door lock preven-
tion may not operate.)
■ If the smart access system with push-
button start does not operate properly
● Locking and unlocking the doors: Use
the mechanical key. (P.430)
● Starting the hybrid system: P.431
■ Customization
Settings (e.g. smart access system with
push-button start) can be changed.
(Customizable features: P.460)
If the smart access system with push-button
start has been deactivated in a customized
setting, refer to the explanations for the fol-
lowing operations.
● Locking and unlocking the doors: Use
the wireless remote control or mechani-
cal key. (P.120, 430)
● Starting the hybrid system and changing
power switch modes: P.431
● Stopping the hybrid system: P.178
WARNING
■ Caution regarding interference with
electronic devices
● People with implantable cardiac pace-
makers, cardiac resynchronization
therapy-pacemakers or implantable
cardioverter defibrillators should
maintain a reasonable distance
between themselves and the smart
access system with push-button start
antennas. (P.138)
The radio waves may affect the opera-
tion of such devices. If necessary, the
entry function can be disabled. Ask
your Lexus dealer for details, such as
the frequency of radio waves and tim-
ing of the emitted radio waves. Then,
consult your doctor to see if you
should disable the entry function.
● User of any electrical medical device
other than implantable cardiac pace-
makers, cardiac resynchronization
therapy-pacemakers or implantable
cardioverter defibrillators should con-
sult the manufacturer of the device for
information about its operation under
the influence of radio waves.
Radio waves could have unexpected
effects on the operation of such medi-
cal devices.
Ask your Lexus dealer for details for dis-
abling the entry function.

Related Topics

Popular Owner Manuals