2019-2026 Lexus UX SUV Using the other interior features User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Using the other interior features for Your Lexus UX SUV First Generation (2019-2026)

328
5-5. Using the other interior features
5-5.Using the other interior feature s
1 To set the visor in the forward posi-
tion, flip it down.
2
To set the visor in the side position,
flip down, unhook, and swing it to
the side.
3
To use the side extender, place the
visor in the side position, then slide
it backward.
■ When adjusting the inside rear view mir-
ror
Adjust the inside rear view mirror to enable
sufficient confirmation of the rear view with-
out interfering with the sun visor.
Slide the cover to open.
The light turns on when the cover is
opened.
■ Vanity lights
If the vanity lights remain on when the
power switch is turned off, the lights will go
off automatically after 20 minutes.
Please use a power supply for elec-
tronic goods that use less than 12
VDC/10 A (power consumption of
120 W).
When using electronic goods, make
sure that the power consumption of all
the connected power outlets is less
than 120 W.
Inside of the console box
Lift the lid while pushing the button to
release the lock.
The console box can be opened from
either side.
Other interior features
Sun visors
NOTICE
■ To prevent damage to the sun visors
When using the side extender, do not
swing the visor to the front.
Vanity mirrors
NOTICE
■ To prevent 12-volt battery discharge
Do not leave the vanity lights on for
extended periods while the hybrid sys-
tem is off.
Power outlet
329
5-5. Using the other interior features
5
Interior features
Open the lid.
Rear
Open the lid.
■ The power outlet can be used when
The power switch is in ACC or ON.
■ When stopping the hybrid system
Disconnect electrical devices with charging
functions, such as mobile battery packs.
If such devices are left connected, the
hybrid system may not stop normally.
The USB Type-C charging ports are
used to supply 3.0 A of electricity at 5
V to external devices.
The USB Type-C charging ports are
for charging only. They are not
designed for data transfer or other
purposes.
Depending on the external device, it
may not charge properly. Refer to the
manual included with the device
before using a USB charging port.
NOTICE
■ When power outlet is not in use
To avoid damaging the power outlet,
close the power outlet lid when the
power outlet is not in use.
Foreign objects or liquids that enter the
power outlet may cause a short circuit.
■ To prevent 12-volt battery discharge
Do not use the power outlet longer than
necessary when the hybrid system is off.
■ To prevent incorrect operation of the
vehicle
When turning the power switch off, make
sure to disconnect accessories designed
for charging, such as portable chargers,
power banks, etc. from the power out-
lets.
If such an accessory is left connected, the
following may occur:
● The doors will not be able to be
locked.
● The opening screen will be displayed
on the multi-information display.
● The interior lights, instrument panel
lights, etc. will illuminate.
USB Type-C charging ports
330
5-5. Using the other interior features
■ Using the USB Type-C charging
ports
Front
Rear side of the console box
Open the lid.
■ The USB Type-C charging ports can be
used when
The power switch is in ACC or ON.
■ Situations in which the USB Type-C
charging ports may not operate cor-
rectly
● If a device which consumes more than
3.0 A at 5 V is connected
● If a device designed to communicate with
a personal computer, such as a USB
memory device, is connected
● If the connected external device is turned
off (depending on device)
● If the temperature inside the vehicle is
high, such as after the vehicle has been
parked in the sun
■ About connected external devices
Depending on the connected external
device, charging may occasionally be sus-
pended and then start again. This is not a
malfunction.
A portable device can be charged by
just placing Qi standard wireless
charge compatible portable devices
according to the Wireless Power Con-
sortium, such as smartphones and
NOTICE
■ To prevent damage to the USB Type-
C charging ports
● Do not insert foreign objects into the
ports.
● Do not spill water or other liquids into
the ports.
● Rear side of console box: When the
USB Type-C charging ports are not in
use, close the lids. If a foreign object or
liquid enters a port may cause a short
circuit.
● Do not apply excessive force to or
impact the USB Type-C charging
ports.
● Do not disassemble or modify the USB
Type-C charging ports.
■ To prevent damage to external
devices
● Do not leave external devices in the
vehicle. The temperature inside the
vehicle may become high, resulting in
damage to an external device.
● Do not push down on or apply unnec-
essary force to an external device or
the cable of an external device while it
is connected.
■ To prevent 12-volt battery discharge
Do not use the USB Type-C charging
ports for a long period of time with the
hybrid system stopped.
Wireless charger (if equipped)
331
5-5. Using the other interior features
5
Interior features
mobile batteries, etc., on the charge
area.
The compatible portable devices can
be found on the following Wireless
Power Consortium website.
This function cannot be used with por-
table devices that cannot be placed on
the wireless charger. Also, depending
on the portable device, it may not
operate as normal. Please read the
operation manual for portable devices
to be used.
■ The “Qi” logo
The “Qi” logo is a trademark of the
Wireless Power Consortium.
■ Name for all parts
Operation indicator light
Charge area
*
Charging tray
Approximately 3.9 in. (10 cm)
Approximately 1.0 in. (2.5 cm)
*
: The charging coil in the wireless charger
can be moved within the charge area up
to the position of the charging coil inside
a portable device. Charging is possible if
the center of the coil of the portable
device is placed within the charge area.
If 2 or more portable devices are placed
on the wireless charger, their charging
coils may not be properly detected and
they may not be charged.
■ Using the wireless charger
Place the portable device on the wire-
less charger.
Place the charging side of the portable
device down with the center of the device
in the center of the charge area.
A
B
C
D
E
332
5-5. Using the other interior features
When charging, the operation indicator
light (orange) on the wireless charger
comes on.
Refer to “Situations in which the function
may not operate normally” (P.336)
when charging is not performed.
When charging is complete, the operation
indicator light (green) on the wireless char-
ger comes on.
■ Recharging function
When charging is complete and
after a fixed time in the charge sus-
pension state, charging restarts.
When a portable device is moved
significantly in the charge area, the
charging coil is disconnected and
charging is stopped momentarily.
However, if there is the center of a
charging coil in the charge area, the
charging coil inside the wireless
charger will move toward it and
then charging restarts. If the porta-
ble device is moved to somewhere
outside of the charge area, charging
will stop. Place the portable device
near the center of the charge area.
■ Rapid charging function
The following portable devices sup-
port rapid charging.
• Portable devices compliant with WPC
Ver1.3.2 and compatible with rapid
charging
• iPhone’s with an iOS version that sup-
ports 7.5 W charging (iPhone 8 and
later models)
• Portable devices compatible with Gal-
axy original rapid charging standard.
When a portable device that sup-
ports rapid charging is charged,
charging automatically switches to
the rapid charging function.
■ Lighting conditions of operation indicator light
*1
: Charging power will not be output during standby. A metallic object will not be heated,
if it is placed on the wireless charger in this state.
*2
: Depending on the portable device, there are cases where the operation indicator light
Operation indicator light
Conditions
Charging tray side Center display side
Turning off Disappear
When power for Multimedia is off or the
power switch is off
Green (comes on) Gray
On Standby (charging possible state)
*1
When charging is complete
*2
Orange (comes on) Blue Charging
333
5-5. Using the other interior features
5
Interior features
will continue being lit up orange even after the charging is complete.
■ When the wireless charger does not operate properly
When the wireless charger does not operate properly, handle the probable cause
based on the following tables.
Operation indicator light
Suspected causes/Handling method
Charging tray side Center display side
Orange (Flashing
repeatedly once
every second)
Gray
Vehicle to wireless charger communication
failure
If the hybrid system is operating, stop and
then restart the hybrid system.
If the power switch is in ACC, start the hybrid
system. (P.177)
Green (Flashing
repeatedly once
every second)
Disappear
*
Wireless charger and multimedia system
communication failure
If the hybrid system is operating, stop and
then restart the hybrid system.
If the power switch is in ACC, start the hybrid
system. (P.177)
Green (comes on) Blue
AM radio stations are being automatically
selected (if equipped)
Wait until the system has completed the
automatic selection of AM radio stations.
In the case that automatic selection can-
not be completed, stop automatic selec-
tion.
The smart access system with push-button is
detecting the electronic key.
Wait until electronic key detection has
completed.
334
5-5. Using the other interior features
Green (comes on) Gray
Foreign substance detection:
The abnormal heating prevention function
for foreign substances operated due to the
presence of a metallic foreign substance in
the charge area
Remove the foreign substance from the
charge area.
Portable device misaligned / distanced from
charging surface:
The center of charging coil in the portable
device moved outside of the charging area,
or lens convex is large, or case is thick so the
abnormal heating prevention function oper-
ated
Remove the portable device from the
wireless charger, after 5 seconds, then
place the portable device so that it is near
the center of the wireless charger. Also, if
a case or cover is installed to the portable
device, remove it.
Operation indicator light
Suspected causes/Handling method
Charging tray side Center display side
335
5-5. Using the other interior features
5
Interior features
*
: Depending on the abnormal condition, the Center display may be gray.
■ The wireless charger can be operated
when
The power switch is in ACC or ON.
■ Usable portable devices
● Devices compatible with wireless
charging Qi standards can be used.
However, compatibility with portable
devices that comply with Qi Ver. 1.0,
1.3.2 and later versions is not guaranteed.
● Starting with mobile phones and smart-
phones, it is aimed for low power electri-
cally supplied portable devices of no
more than 5W.
● However, charging exceeding 5 W is
supported by the following portable
devices.
• Charging at 7.5 W or less is supported
by iPhone’s that support 7.5 W charging.
• Charging at 10 W or less is supported by
Galaxy device that support 10 W
charging of original standard.
• Charging at 15 W or less is supported by
portable devices compliant with EPP out-
put as defined by WPC standard
Ver1.3.2.
■ Using the smart access system with
push-button
If the smart access system with push-button
detects the electronic key while a device is
being charged, charging will be temporarily
stopped. When the electronic key is
detected, charging will automatically start
again.
■ When covers and accessories are
attached to portable devices
Do not charge in situations where cover
and accessories not able to handle Qi are
attached to the portable device. Depending
on the type of cover (including for certain
Green (comes on) Gray
Battery protection function of portable
device:
Before full charging, battery protection
function of portable device operated
Confirm the setting of portable device.
Continued detection of an electronic key:
When a Multimedia function is used through
vehicle customization, the electronic key is
continually detected without being con-
firmed.
In this case, turn the power switch ACC
or ON to confirm the key.
Orange (Repeat-
edly flashes 4 times
continuously)
Gray
Safety shutdown resulting when the tem-
perature within the wireless charger
exceeded the set value
Stop charging, remove the portable
device from the wireless charger, wait for
the temperature to drop, and then start
charging again.
Operation indicator light
Suspected causes/Handling method
Charging tray side Center display side
336
5-5. Using the other interior features
genuine manufacturer parts) and acces-
sory, it may not be possible to charge.
When charging is not performed even with
the portable device placed on the charge
area, remove the cover and accessories.
■ AM radio cooperation function during
charging
● When noise enters the AM radio during
charging, charging frequency will be
automatically changed to reduce noise.
● During the AM radio automatic tuning,
charging is temporarily stopped in order
to prevent tuning error due to noise
caused by charging. When tuning is fin-
ished, charging will be automatically
resumed.
■ Important points of the wireless charger
● If the electronic key cannot be detected
within the vehicle interior, charging can-
not be done. When the door is opened
and closed, charging may be temporarily
suspended.
● When charging, the wireless charging
device and portable device will get
warmer, however this is not a malfunc-
tion.
When a portable device gets warm while
charging, charging may stop due to the
protection function on the portable
device side. In this case, when the tem-
perature of the portable device drops
significantly, charge again.
The fan may start operating to lower the
temperature inside the wireless charger,
however this is not a malfunction.
■ Operation sounds
A buzzing noise may be heard when press-
ing the power switch to turn to ACC or ON
or when detecting a portable device. How-
ever, this is not a malfunction.
■ Cleaning the wireless charger
P.350
■ Situations in which the function may not
operate normally
Devices may not be charged normally in
the following situations.
● The portable device is fully charged
● The portable device is being charged
with a cable connected
● There is foreign matter between the
charge area and portable device
● Charging has caused the portable device
to heat up
● The temperature around the wireless
charger is 95°F (35°C) or higher, such
as in extreme heat
● The portable device is placed with its
charging surface facing up
● The small portable device such as fold-
able type is placed in an area misaligned
from the charge area
● The portable device is larger than the
charging tray
● The vehicle is in an area where strong
electrical waves or noise are emitted,
such as near a television tower, power
plant, gasoline station, broadcasting sta-
tion, large display, airport, etc.
● The electronic key is not inside the vehi-
cle
● Any of the following is stuck or installed
between the charging side of the porta-
ble device and the charge area.
• Thick cases or covers
• A case or cover attached with an uneven
or tilted surface, so that the charging side
is not flat
• Thick decorations
• Accessories, such as finger rings, straps,
etc.
● When there is a gap between the
charging side of the portable device and
the charge area due to a protrusion such
as a camera on the charging side of the
portable device.
● When the portable device is in contact
with, or is covered by any of the following
metallic objects:
• A card that has metal on it, such as alumi-
num foil, etc.
• A pack of cigarettes that includes alumi-
num foil
• A wallet or bag that is made of metal
• Coins
• A heating pad
• CDs, DVDs or other media
• A metal accessory
337
5-5. Using the other interior features
5
Interior features
• A case or cover made of metal
• A flip type case with a magnet on the
charging side of the portable device
● Electric wave type wireless remote con-
trols are being used nearby
● 2 or more portable devices are placed on
the wireless charger at the same time
● If you use a device with a built-in S-Pen
(Galaxy Note series, etc.) and the device
with the S-Pen inserted is on the tray.
If charging is abnormal or the operation
indicator light continues to flash for any
other reason, the wireless charger may be
malfunctioning. Contact any authorized
Lexus retailer or Lexus authorized repairer,
or any reliable repairer.
■ If the smartphone OS has been updated
If the smartphone OS has been updated to
a newer version, its charging specifications
may have changed significantly. For details,
check the information on the manufac-
turer’s website.
■ Trademark information
● iPhone is a trademark of Apple Inc., reg-
istered in the U.S. and other countries.
● Galaxy is a trademark or registered
trademark of Samsung Electronics
Co.,Ltd.
WARNING
■ Caution while driving
When charging a portable device, for
safety reasons, the driver should not
operate the main part of the portable
device while driving.
■ Precautions for when driving
Do not charge small, lightweight porta-
ble devices, such as wireless earbuds,
while driving. Lightweight devices may
fly off of the charging tray, possibly lead-
ing to an accident.
■ Caution regarding interference with
electronic devices
People with implantable cardiac pace-
makers, cardiac resynchronization ther-
apy-pacemakers or implantable
cardioverters, as well as any other elec-
trical medical device, should consult their
physician about the usage of the wireless
charger.
■ To prevent malfunctions or burns
Observe the following precautions. Fail-
ure to do so may result in a equipment
failure and damage, catch fire, burns due
to overheat or electric shock.
● Do not insert any metallic objects
between the charge area and the por-
table device while charging
● Do not attach an aluminum sticker or
other metallic object to the charge
area
● Do not attach an aluminum sticker or
other metallic object to the side of the
portable device (or to its case or
cover) that touches the charge area
● Do not store items on the wireless
charger instead of in an auxiliary box
● Do not subject to a strong force or
impact
● Do not disassemble, modify or remove
● Do not charge devices other than
specified portable devices
● Keep away from magnetic items
● Do not perform charging if the
charging area is dirty
● Do not cover with a cloth or similar
material
338
5-5. Using the other interior features
Fold down the armrest for use.
The coat hooks are provided with the
rear assist grips.
An assist grip installed on the ceiling
can be used to support your body
while sitting on the seat.
NOTICE
■ To prevent malfunctions and data
corruptions
● When charging, bringing a credit, or
other magnetic card, or magnetic stor-
age media close to the charge area
may clear any stored data due to mag-
netic influence. Also, do not bring a
wristwatch or other precision instru-
ment close to the charge area since
doing so may cause it to malfunction.
● Do not charge with a non-contact IC
card such as a transportation system
IC card inserted between the charging
side of a portable device and the
charge area. The IC chip may become
extremely hot and damage the porta-
ble device or IC card. Be especially
careful not to charge a portable device
inside a case or cover with a non-con-
tact IC card attached.
● Do not leave portable devices inside
the vehicle. The inside of the vehicle
can become hot in extreme heat,
which could cause a malfunction.
■ To prevent 12-volt battery discharge
Do not use the wireless charger for a
long period of time when the hybrid sys-
tem is stopped.
Armrest
NOTICE
■ To prevent damage to the armrest
Do not apply too much load on the arm-
rest.
Coat hooks
WARNING
■ Items that must not be hung on the
hook
Do not hang coat hangers or other hard
or sharp objects on the hook. If the SRS
curtain shield airbags deploy, these items
may become projectiles, causing death
or serious injury.
Assist grips
339
5-5. Using the other interior features
5
Interior features
*
: If equipped
■ HomeLink
®
programming procedure
The programming procedures can also be
found at the following URL.
Website: www.homelink.com/lexus
For support, contact customer support at
the following.
Help Line: 1-800-355-3515
The HomeLink
®
wireless control sys-
tem in your vehicle has 3 buttons
which can be programmed to operate
3 different devices. Refer to the pro-
gramming methods on the following
pages to determine the method which
is appropriate for the device.
WARNING
■ Assist grips
Do not use the assist grip when getting in
or out of the vehicle or rising from your
seat.
NOTICE
■ To prevent damage to the assist grip
Do not hang any heavy object or put a
heavy load on the assist grip.
Garage door opener
*
The garage door opener can be
programmed using the
HomeLink
®
to operate garage
doors, gates, entry doors, door
locks, home lighting systems, secu-
rity systems, and other devices.
System components
340
5-5. Using the other interior features
HomeLink
®
indicator light
Garage door operation indicators
HomeLink
®
icon
Illuminates while HomeLink
®
is operating.
Buttons
■ Codes stored in the HomeLink
®
mem-
ory
● The registered codes are not erased
even if the 12-volt battery cable is discon-
nected.
● If learning failed when registering a dif-
ferent code to a HomeLink
®
button that
already has a code registered to it, the
already registered code will not be
erased.
■ Before programming HomeLink
®
During programming, it is possible
that garage doors, gates, or other
devices may operate. For this rea-
son, make sure that people and
objects are clear of the garage door
or other devices to prevent injury or
other potential harm.
It is recommended that a new bat-
tery be placed in the remote control
transmitter for more accurate pro-
gramming.
Garage door opener motors manu-
factured after 1995 may be
equipped with rolling code protec-
tion. If this is the case, you may need
a stepladder or other sturdy, safe
device to reach the “Learn” or
“Smart” button on the garage door
opener motor.
WARNING
■ When programming a garage door
or other remote control device
The garage door or other device may
operate, so ensure people and objects
are out of danger to prevent potential
harm.
A
B
C
D
■ Conforming to federal safety stan-
dards
Do not use the HomeLink
®
compatible
transceiver with any garage door opener
or device that lacks safety stop and
reverse features as required by federal
safety standards.
This includes any garage door that can-
not detect an interfering object. A door
or device without these features
increases the risk of death or serious
injury.
■ When operating or programming
HomeLink
®
Never allow a child to operate or play
with the HomeLink
®
buttons.
Programming the HomeLink
®
341
5-5. Using the other interior features
5
Interior features
■ Programming HomeLink
®
Steps
1 through 3 must be performed
within 60 seconds, otherwise the indi-
cator light will stop flashing and pro-
gramming will not be able to be
completed.
1 Press and release the HomeLink
®
button you want to program and
check that the HomeLink
®
indica-
tor light flashes (orange).
2 Point the remote control transmit-
ter for the device at the rear view
mirror, 1 to 3 in. (25 to 75 mm)
from the HomeLink
®
buttons.
Keep the HomeLink
®
indicator light in
view while programming.
3 Program a device.
Programming a device other than
an entry gate (for U.S.A. owners)
Press and hold the remote control
transmitter button until the
HomeLink
®
indicator light changes
from slowly flashing orange to rapidly
flashing green (rolling code) or contin-
uously lit green (fixed code), then
release the button.
Programming an entry gate (for
U.S.A. owners)/Programming a
device in the Canadian market
Press and release the remote control
transmitter button at 2 second inter-
vals, repeatedly, until the HomeLink
®
indicator light changes from slowly
flashing (orange) to rapidly flashing
(green) (rolling code) or continuously
lit (green) (fixed code).
4 Test the HomeLink
®
operation by
pressing the newly programmed
button and observing the indicator
light:
Indicator light illuminates: Program-
ming of a fixed code device has
completed. The garage door or
other device should operate when a
HomeLink
®
button is pressed and
released.
Indicator light flashes rapidly: The
garage door opener motor or other
device is equipped with a rolling
code. To complete programming,
firmly press and hold the
HomeLink
®
button for 2 seconds
then release it.
If the garage door or other device
does not operate, proceed to “Pro-
gramming a rolling code system”.
342
5-5. Using the other interior features
5 Repeat the steps above to program
another device for any of the
remaining HomeLink
®
buttons.
■ Programming a rolling code sys-
tem
2 or more people may be necessary to
complete rolling code programming.
1 Locate the “Learn” or “Smart” but-
ton on the garage door opener
motor in the garage.
This button can usually be found where the
hanging antenna wire is attached to the
unit. The name and color of the button may
vary by manufacturer. Refer to the owner’s
manual supplied with the garage door
opener motor for details.
2 Press and release the “Learn” or
“Smart” button.
Perform 3 within 30 seconds after
performing
2.
3 Press and hold the desired
HomeLink
®
button (inside the
vehicle) for 2 seconds and release
it. Repeat this sequence
(press/hold/release) up to 3 times
to complete programming.
If the garage door opener motor
operates when the HomeLink
®
button is pressed, the garage door
opener motor recognizes the
HomeLink
®
signal.
■ Enabling 2-way communication
with a garage door (only available
for compatible devices)
When enabled, 2-way communication
allows you to check the status of the
opening and closing of a garage door
through indicators in your vehicle.
2-way communication is only available
if the garage door opener motor used
is a compatible device. (To check
device compatibility, refer to
1 Within 5 seconds after program-
ming the garage door opener has
been completed, if the garage door
opener motor is trained to
HomeLink
®
, both garage door
operation indicators will flash rap-
idly (green) and the light on the
garage door opener motor will
343
5-5. Using the other interior features
5
Interior features
blink twice, indicating that 2-way
communication is enabled.
If the indicators do not flash, perform
2 and
3 within the first 10 presses of the
HomeLink
®
button after programming
has been completed.
2 Press a programmed HomeLink
®
button to operate a garage door.
3 Within 1 minute of pressing the
HomeLink
®
button, after the
garage door operation has
stopped, press the “Learn” or
“Smart” button on the garage door
opener motor. Within 5 seconds of
the establishment of 2-way com-
munication with the garage door
opener, both garage door opera-
tion indicators in the vehicle will
flash rapidly (green) and the light
on the garage door opener motor
will blink twice, indicating that 2-
way communication is enabled.
■ Reprogramming a single
HomeLink
®
button
When the following procedure is per-
formed, buttons which already have
devices registered to them can be
overwritten:
1 With one hand, press and hold the
desired HomeLink
®
button.
2 When the HomeLink
®
indicator
starts flashing (orange), continue to
hold the HomeLink
®
button and
perform “Programming
HomeLink
®
”
1 (it takes 20 sec-
onds for the HomeLink
®
indicator
to start flashing).
■ Before programming
● Install a new battery in the transmitter.
● The battery side of the transmitter must
be pointed away from the HomeLink
®
.
Press the appropriate HomeLink
®
button. The HomeLink
®
indicator light
should turn on.
The status of the opening and closing
of a garage door is shown by the indi-
cators.
Opening
Closing
This function is only available if the garage
door opener motor used is a compatible
device. (To check device compatibility,
refer to .)
The indicators can operate within
approximately 820 ft. (250 m) of the
Operating HomeLink
®
Color Status
Orange (flashing)
Currently open-
ing/closing
Green
Opening/closing
has completed
Red (flashing)
Feedback signals
cannot be received
A
B
344
5-5. Using the other interior features
garage door. However, if there are
obstructions between the garage door
and the vehicle, such as houses and
trees, feedback signals from the
garage door may not be received.
To recall the previous door operation
status, press and release either
HomeLink
®
buttons and
or and simulta-
neously. The last recorded status will
be displayed for 3 seconds.
Press and hold the 2 outside buttons
for 10 seconds until the HomeLink
®
indicator light changes from continu-
ously lit (orange) to rapidly flashing
(green).
If you sell your vehicle, be sure to erase the
programs stored in the HomeLink
®
mem-
ory.
Erasing the entire HomeLink
®
memory (all three codes)

Related Topics

Popular Owner Manuals